path: root/target/linux/ubicom32/patches-2.6.32/100-ubicom32_support.patch

--- a/drivers/char/hw_random/Kconfig
+++ b/drivers/char/hw_random/Kconfig
@@ -186,3 +186,16 @@ config HW_RANDOM_MXC_RNGA
 	  module will be called mxc-rnga.
 
 	  If unsure, say Y.
+
+config HW_RANDOM_UBICOM32
+	tristate "Ubicom32 HW Random Number Generator support"
+	depends on HW_RANDOM && UBICOM32
+	default HW_RANDOM
+	---help---
+	  This driver provides kernel-side support for the Random Number
+	  Generator hardware found on Ubicom32 processors.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called pasemi-rng.
+
+	  If unsure, say Y.
--- a/drivers/char/hw_random/Makefile
+++ b/drivers/char/hw_random/Makefile
@@ -18,3 +18,4 @@ obj-$(CONFIG_HW_RANDOM_VIRTIO) += virtio
 obj-$(CONFIG_HW_RANDOM_TX4939) += tx4939-rng.o
 obj-$(CONFIG_HW_RANDOM_MXC_RNGA) += mxc-rnga.o
 obj-$(CONFIG_HW_RANDOM_OCTEON) += octeon-rng.o
+obj-$(CONFIG_HW_RANDOM_UBICOM32) += ubicom32-rng.o
--- a/drivers/crypto/Kconfig
+++ b/drivers/crypto/Kconfig
@@ -61,6 +61,40 @@ config CRYPTO_DEV_GEODE
 	  To compile this driver as a module, choose M here: the module
 	  will be called geode-aes.
 
+config CRYPTO_UBICOM32
+        bool "Ubicom32 Security Module"
+        depends on UBICOM32
+        help
+          This is the ubicom32 hardware acceleration common code.
+
+config CRYPTO_AES_UBICOM32
+        tristate "Ubicom32 AES implementation"
+        depends on CRYPTO_UBICOM32
+        select CRYPTO_ALGAPI
+        help
+          This is the ubicom32 hardware AES implementation.
+
+config CRYPTO_DES_UBICOM32
+        tristate "Ubicom32 DES implementation"
+        depends on CRYPTO_UBICOM32
+        select CRYPTO_ALGAPI
+        help
+          This is the ubicom32 hardware DES and 3DES implementation.
+
+config CRYPTO_SHA1_UBICOM32
+        tristate "Ubicom32 SHA1 implementation"
+        depends on CRYPTO_UBICOM32
+        select CRYPTO_ALGAPI
+        help
+          This is the ubicom32 hardware SHA1 implementation.
+
+config CRYPTO_MD5_UBICOM32
+        tristate "Ubicom32 MD5 implementation"
+        depends on CRYPTO_UBICOM32
+        select CRYPTO_ALGAPI
+        help
+          This is the ubicom32 hardware MD5 implementation.
+
 config ZCRYPT
 	tristate "Support for PCI-attached cryptographic adapters"
 	depends on S390
--- a/drivers/mmc/host/Kconfig
+++ b/drivers/mmc/host/Kconfig
@@ -382,3 +382,10 @@ config MMC_VIA_SDMMC
 	  If you have a controller with this interface, say Y or M here.
 
 	  If unsure, say N.
+
+config MMC_UBICOM32
+	tristate "Ubicom32 MMC/SD host controller"
+	depends on UBICOM32
+	help
+	  This provides support for the SD/MMC hardware found on Ubicom32
+	  IP7K processors
--- a/drivers/mmc/host/Makefile
+++ b/drivers/mmc/host/Makefile
@@ -35,6 +35,7 @@ obj-$(CONFIG_MMC_TMIO)		+= tmio_mmc.o
 obj-$(CONFIG_MMC_CB710)	+= cb710-mmc.o
 obj-$(CONFIG_MMC_VIA_SDMMC)	+= via-sdmmc.o
 obj-$(CONFIG_GPIOMMC)		+= gpiommc.o
+obj-$(CONFIG_MMC_UBICOM32)	+= ubicom32sd.o
 
 ifeq ($(CONFIG_CB710_DEBUG),y)
 	CFLAGS-cb710-mmc	+= -DDEBUG
--- a/drivers/mtd/devices/Kconfig
+++ b/drivers/mtd/devices/Kconfig
@@ -114,6 +114,31 @@ config MTD_SST25L
 	  Set up your spi devices with the right board-specific platform data,
 	  if you want to specify device partitioning.
 
+config MTD_UBI32_NAND_SPI_ER
+	tristate "UBI32_NAND SPI-ER support"
+	help
+	  This driver supports the Micron MT29F1G01 SPI-ER NAND flash chip
+	  using the built in flash controller on the Ubicom32 architecture.
+	  Partial page writes are not supported by this driver.
+
+config MTD_NAND_SPI_ER
+	tristate "NAND SPI-ER support"
+	help
+	  This driver supports the Micron MT29F1G01 SPI-ER NAND flash chip
+	  using a generic SPI bus.  Partial page writes are supported
+	  by this driver.
+
+config MTD_UBI32_M25P80
+	tristate "Ubicom processor support for most SPI Flash chips (AT26DF, M25P, W25X, ...)"
+	depends on UBICOM32
+	default y
+	help
+	  This enables access to most modern SPI flash chips, used for
+	  program and data storage.   Series supported include Atmel AT26DF,
+	  Spansion S25SL, SST 25VF, ST M25P, and Winbond W25X.  Other chips
+	  are supported as well.  See the driver source for the current list,
+	  or to add other chips.
+
 config MTD_SLRAM
 	tristate "Uncached system RAM"
 	help
--- a/drivers/mtd/devices/Makefile
+++ b/drivers/mtd/devices/Makefile
@@ -17,3 +17,6 @@ obj-$(CONFIG_MTD_BLOCK2MTD)	+= block2mtd
 obj-$(CONFIG_MTD_DATAFLASH)	+= mtd_dataflash.o
 obj-$(CONFIG_MTD_M25P80)	+= m25p80.o
 obj-$(CONFIG_MTD_SST25L)	+= sst25l.o
+obj-$(CONFIG_MTD_UBI32_M25P80)	+= ubi32-m25p80.o
+obj-$(CONFIG_MTD_NAND_SPI_ER)	+= nand-spi-er.o
+obj-$(CONFIG_MTD_UBI32_NAND_SPI_ER)	+= ubi32-nand-spi-er.o
--- a/drivers/net/Kconfig
+++ b/drivers/net/Kconfig
@@ -2608,6 +2608,19 @@ config S6GMAC
 
 source "drivers/net/stmmac/Kconfig"
 
+config UBICOM32_GMAC
+	tristate "Ubicom Gigabit Ethernet support"
+	depends on UBICOM32
+	help
+	  Gigabit Ethernet support for ubicom32 processors
+
+config UBICOM32_OCM_FOR_SKB
+        bool  "USE OCM for SKB (EXPERIMENTAL)"
+        depends on UBICOM32_GMAC
+	default n
+        help
+          Allocate skb from OCM for Ethernet Receive when possible
+
 endif # NETDEV_1000
 
 #
--- a/drivers/net/Makefile
+++ b/drivers/net/Makefile
@@ -286,3 +286,5 @@ obj-$(CONFIG_VIRTIO_NET) += virtio_net.o
 obj-$(CONFIG_SFC) += sfc/
 
 obj-$(CONFIG_WIMAX) += wimax/
+
+obj-$(CONFIG_UBICOM32_GMAC) += ubi32-eth.o
--- a/drivers/net/usb/asix.c
+++ b/drivers/net/usb/asix.c
@@ -319,14 +319,33 @@ static int asix_rx_fixup(struct usbnet *
 		/* get the packet length */
 		size = (u16) (header & 0x0000ffff);
 
-		if ((skb->len) - ((size + 1) & 0xfffe) == 0)
+		if ((skb->len) - ((size + 1) & 0xfffe) == 0) {
+#ifndef HAVE_EFFICIENT_UNALIGNED_ACCESS
+			if (((u32)packet & 0x02) == 0) {
+				memmove(packet - 2, packet, size);
+				skb->data -= 2;
+				skb->tail -= 2;
+			}
+#endif
 			return 2;
+		}
+
 		if (size > ETH_FRAME_LEN) {
 			deverr(dev,"asix_rx_fixup() Bad RX Length %d", size);
 			return 0;
 		}
 		ax_skb = skb_clone(skb, GFP_ATOMIC);
 		if (ax_skb) {
+#ifndef HAVE_EFFICIENT_UNALIGNED_ACCESS
+			if (((u32)packet & 0x02) == 0) {
+				memmove(packet - 2, packet, size);
+				ax_skb->data = packet - 2;
+			} else {
+				ax_skb->data = packet;
+			}
+#else
+			ax_skb->data = packet;
+#endif
 			ax_skb->len = size;
 			ax_skb->data = packet;
 			skb_set_tail_pointer(ax_skb, size);
@@ -1125,13 +1144,19 @@ static int ax88178_link_reset(struct usb
 	mode = AX88178_MEDIUM_DEFAULT;
 
 	if (ecmd.speed == SPEED_1000)
+#ifdef HAVE_EFFICIENT_UNALIGNED_ACCESS
 		mode |= AX_MEDIUM_GM;
+#else
+		mode |= AX_MEDIUM_GM | AX_MEDIUM_ENCK;
+#endif
 	else if (ecmd.speed == SPEED_100)
 		mode |= AX_MEDIUM_PS;
 	else
 		mode &= ~(AX_MEDIUM_PS | AX_MEDIUM_GM);
 
+#ifdef HAVE_EFFICIENT_UNALIGNED_ACCESS
 	mode |= AX_MEDIUM_ENCK;
+#endif
 
 	if (ecmd.duplex == DUPLEX_FULL)
 		mode |= AX_MEDIUM_FD;
--- a/drivers/oprofile/cpu_buffer.c
+++ b/drivers/oprofile/cpu_buffer.c
@@ -327,10 +327,10 @@ static inline void oprofile_end_trace(st
 }
 
 static inline void
-__oprofile_add_ext_sample(unsigned long pc, struct pt_regs * const regs,
-			  unsigned long event, int is_kernel)
+__oprofile_add_ext_sample_cpu(unsigned long pc, struct pt_regs * const regs,
+			      unsigned long event, int is_kernel, int cpu)
 {
-	struct oprofile_cpu_buffer *cpu_buf = &__get_cpu_var(cpu_buffer);
+	struct oprofile_cpu_buffer *cpu_buf = &per_cpu(cpu_buffer, cpu);
 	unsigned long backtrace = oprofile_backtrace_depth;
 
 	/*
@@ -352,7 +352,8 @@ __oprofile_add_ext_sample(unsigned long 
 void oprofile_add_ext_sample(unsigned long pc, struct pt_regs * const regs,
 			     unsigned long event, int is_kernel)
 {
-	__oprofile_add_ext_sample(pc, regs, event, is_kernel);
+	__oprofile_add_ext_sample_cpu(pc, regs, event,
+				      is_kernel, smp_processor_id());
 }
 
 void oprofile_add_sample(struct pt_regs * const regs, unsigned long event)
@@ -360,7 +361,8 @@ void oprofile_add_sample(struct pt_regs 
 	int is_kernel = !user_mode(regs);
 	unsigned long pc = profile_pc(regs);
 
-	__oprofile_add_ext_sample(pc, regs, event, is_kernel);
+	__oprofile_add_ext_sample_cpu(pc, regs, event,
+				      is_kernel, smp_processor_id());
 }
 
 /*
--- a/drivers/pci/Makefile
+++ b/drivers/pci/Makefile
@@ -47,8 +47,8 @@ obj-$(CONFIG_PPC) += setup-bus.o
 obj-$(CONFIG_MIPS) += setup-bus.o setup-irq.o
 obj-$(CONFIG_X86_VISWS) += setup-irq.o
 obj-$(CONFIG_MN10300) += setup-bus.o
+obj-$(CONFIG_UBICOM32) += setup-bus.o setup-irq.o
 
-#
 # ACPI Related PCI FW Functions
 #
 obj-$(CONFIG_ACPI)    += pci-acpi.o
--- a/drivers/serial/Kconfig
+++ b/drivers/serial/Kconfig
@@ -879,6 +879,57 @@ config SERIAL_UARTLITE_CONSOLE
 	  console (the system console is the device which receives all kernel
 	  messages and warnings and which allows logins in single user mode).
 
+config SERIAL_UBI32_UARTTIO
+        tristate "Ubicom UARTTIO support"
+        depends on UBICOM32=y
+        select SERIAL_CORE
+	default y
+        help
+          Add support for the Ubicom virtual peripherial serial interface.
+
+config SERIAL_UBI32_UARTTIO_NR_UARTS
+	int "Maximum number of UARTTIO virtual serial ports"
+	depends on SERIAL_UBI32_UARTTIO
+	default "4"
+	help
+	  Set this to the maximum number of serial ports you want the driver to support.
+
+config SERIAL_UBI32_UARTTIO_CONSOLE
+        tristate "Ubicom UARTTIO console support"
+        depends on SERIAL_UBI32_UARTTIO=y
+        select SERIAL_CORE_CONSOLE
+	default y
+        help
+          Add support for console on the Ubicom virtual peripherial serial interface.
+
+config SERIAL_UBI32_SERDES
+        bool "Ubicom serial port support"
+        depends on UBICOM32=y
+        select SERIAL_CORE
+	default y
+        help
+          Add support for the Ubicom serial interface.
+
+config SERIAL_UBI32_SERDES_CONSOLE
+        bool "Ubicom serial console support"
+        depends on SERIAL_UBI32_SERDES=y
+        select SERIAL_CORE_CONSOLE
+	default y
+
+config SERIAL_UBI32_MAILBOX
+        bool "Ubicom mailbox support"
+        depends on UBICOM32=y
+        select SERIAL_CORE
+	default n
+        help
+          Add support for the Ubicom mailbox interface.
+
+config SERIAL_UBI32_MAILBOX_CONSOLE
+        bool "Ubicom mailbox console support"
+        depends on SERIAL_UBI32_MAILBOX=y
+        select SERIAL_CORE_CONSOLE
+	default y
+
 config SERIAL_SUNCORE
 	bool
 	depends on SPARC
--- a/drivers/serial/Makefile
+++ b/drivers/serial/Makefile
@@ -81,3 +81,6 @@ obj-$(CONFIG_SERIAL_KS8695) += serial_ks
 obj-$(CONFIG_KGDB_SERIAL_CONSOLE) += kgdboc.o
 obj-$(CONFIG_SERIAL_QE) += ucc_uart.o
 obj-$(CONFIG_SERIAL_TIMBERDALE)	+= timbuart.o
+obj-$(CONFIG_SERIAL_UBI32_SERDES) += ubi32_serdes.o
+obj-$(CONFIG_SERIAL_UBI32_UARTTIO) += ubi32_uarttio.o
+obj-$(CONFIG_SERIAL_UBI32_MAILBOX) += ubi32_mailbox.o
--- a/drivers/spi/Kconfig
+++ b/drivers/spi/Kconfig
@@ -214,6 +214,15 @@ config SPI_S3C24XX
 	help
 	  SPI driver for Samsung S3C24XX series ARM SoCs
 
+config SPI_UBICOM32_GPIO
+	tristate "Ubicom32 SPI over GPIO"
+	depends on SPI_MASTER && UBICOM32 && EXPERIMENTAL
+	select SPI_BITBANG
+	select HAS_DMA
+	help
+	  SPI driver for the Ubicom32 architecture using
+	  GPIO lines to provide the SPI bus.
+
 config SPI_S3C24XX_GPIO
 	tristate "Samsung S3C24XX series SPI by GPIO"
 	depends on ARCH_S3C2410 && EXPERIMENTAL
--- a/drivers/spi/Makefile
+++ b/drivers/spi/Makefile
@@ -29,6 +29,7 @@ obj-$(CONFIG_SPI_MPC52xx_PSC)		+= mpc52x
 obj-$(CONFIG_SPI_MPC8xxx)		+= spi_mpc8xxx.o
 obj-$(CONFIG_SPI_PPC4xx)		+= spi_ppc4xx.o
 obj-$(CONFIG_SPI_S3C24XX_GPIO)		+= spi_s3c24xx_gpio.o
+obj-$(CONFIG_SPI_UBICOM32_GPIO)		+= spi_ubicom32_gpio.o
 obj-$(CONFIG_SPI_S3C24XX)		+= spi_s3c24xx.o
 obj-$(CONFIG_SPI_TXX9)			+= spi_txx9.o
 obj-$(CONFIG_SPI_XILINX)		+= xilinx_spi.o
--- a/drivers/uio/Kconfig
+++ b/drivers/uio/Kconfig
@@ -94,4 +94,12 @@ config UIO_PCI_GENERIC
 	  primarily, for virtualization scenarios.
 	  If you compile this as a module, it will be called uio_pci_generic.
 
+config UIO_UBICOM32RING
+	tristate "Ubicom32 Ring Buffer driver"
+	default n
+	help
+	  Userspace I/O interface for a Ubicom32 Ring Buffer.
+
+	  If you compile this as a module, it will be called uio_ubicom32ring
+
 endif
--- a/drivers/uio/Makefile
+++ b/drivers/uio/Makefile
@@ -6,3 +6,4 @@ obj-$(CONFIG_UIO_SMX)	+= uio_smx.o
 obj-$(CONFIG_UIO_AEC)	+= uio_aec.o
 obj-$(CONFIG_UIO_SERCOS3)	+= uio_sercos3.o
 obj-$(CONFIG_UIO_PCI_GENERIC)	+= uio_pci_generic.o
+obj-$(CONFIG_UIO_UBICOM32RING)	+= uio_ubicom32ring.o
--- a/drivers/usb/gadget/epautoconf.c
+++ b/drivers/usb/gadget/epautoconf.c
@@ -154,6 +154,10 @@ ep_matches (
 			/* configure your hardware with enough buffering!! */
 		}
 		break;
+
+	case USB_ENDPOINT_XFER_BULK:
+		if ((gadget->is_dualspeed) && (ep->maxpacket < 512))
+			return 0;
 	}
 
 	/* MATCH!! */
--- a/drivers/usb/Kconfig
+++ b/drivers/usb/Kconfig
@@ -22,6 +22,7 @@ config USB_ARCH_HAS_HCD
 	default y if PCMCIA && !M32R			# sl811_cs
 	default y if ARM				# SL-811
 	default y if SUPERH				# r8a66597-hcd
+	default y if UBICOM32				# Ubicom's onchip USB Duial role controller
 	default PCI
 
 # many non-PCI SOC chips embed OHCI
--- a/drivers/usb/musb/Kconfig
+++ b/drivers/usb/musb/Kconfig
@@ -14,7 +14,7 @@ config USB_MUSB_HDRC
 	select TWL4030_USB if MACH_OMAP_3430SDP
 	select NOP_USB_XCEIV if MACH_OMAP3EVM
 	select USB_OTG_UTILS
-	tristate 'Inventra Highspeed Dual Role Controller (TI, ADI, ...)'
+	tristate 'Inventra Highspeed Dual Role Controller (TI, ADI, Ubicom, ...)'
 	help
 	  Say Y here if your system has a dual role high speed USB
 	  controller based on the Mentor Graphics silicon IP.  Then
--- a/drivers/usb/musb/Makefile
+++ b/drivers/usb/musb/Makefile
@@ -30,6 +30,10 @@ ifeq ($(CONFIG_BF52x),y)
 	musb_hdrc-objs	+= blackfin.o
 endif
 
+ifeq ($(CONFIG_UBICOM32), y)
+        musb_hdrc-objs  += ubi32_usb.o
+endif
+
 ifeq ($(CONFIG_USB_GADGET_MUSB_HDRC),y)
 	musb_hdrc-objs		+= musb_gadget_ep0.o musb_gadget.o
 endif
--- a/drivers/usb/musb/musb_core.c
+++ b/drivers/usb/musb/musb_core.c
@@ -105,6 +105,13 @@
 #include <asm/mach-types.h>
 #endif
 
+#ifdef CONFIG_UBICOM32
+#include <asm/ip5000.h>
+#include <asm/ubicom32-tio.h>
+extern void ubi32_usb_init(void);
+extern void ubi32_usb_int_clr(void);
+#endif
+
 #include "musb_core.h"
 
 
@@ -148,8 +155,37 @@ static inline struct musb *dev_to_musb(s
 }
 
 /*-------------------------------------------------------------------------*/
+#if defined(CONFIG_UBICOM32)
+
+/*
+ * Load an endpoint's FIFO
+ */
+void musb_write_fifo(struct musb_hw_ep *hw_ep, u16 wCount, const u8 *pSource)
+{
+	void __iomem *fifo = hw_ep->fifo;
+
+	prefetch((u8 *)pSource);
+
+	DBG(4, "%cX ep%d fifo %p count %d buf %p\n",
+			'T', hw_ep->epnum, fifo, wCount, pSource);
+
+	usb_tio_write_fifo((u32)fifo, (u32)pSource, wCount);
+
+}
+
+/*
+ * Unload an endpoint's FIFO
+ */
+void musb_read_fifo(struct musb_hw_ep *hw_ep, u16 wCount, u8 *pDest)
+{
+
+	void __iomem *fifo = hw_ep->fifo;
+	DBG(4, "%cX ep%d fifo %p count %d buf %p\n",
+			'R', hw_ep->epnum, fifo, wCount, pDest);
+	usb_tio_read_fifo((u32)fifo, (u32)pDest, wCount);
+}
 
-#if !defined(CONFIG_USB_TUSB6010) && !defined(CONFIG_BLACKFIN)
+#elif !defined(CONFIG_USB_TUSB6010) && !defined(CONFIG_BLACKFIN)
 
 /*
  * Load an endpoint's FIFO
@@ -228,8 +264,7 @@ void musb_read_fifo(struct musb_hw_ep *h
 		readsb(fifo, dst, len);
 	}
 }
-
-#endif	/* normal PIO */
+#endif /* !T6010 && !BLACKFIN */
 
 
 /*-------------------------------------------------------------------------*/
@@ -890,12 +925,19 @@ void musb_start(struct musb *musb)
 	musb_writeb(regs, MUSB_TESTMODE, 0);
 
 	/* put into basic highspeed mode and start session */
+#ifndef CONFIG_UBICOM32
 	musb_writeb(regs, MUSB_POWER, MUSB_POWER_ISOUPDATE
 						| MUSB_POWER_SOFTCONN
 						| MUSB_POWER_HSENAB
 						/* ENSUSPEND wedges tusb */
 						/* | MUSB_POWER_ENSUSPEND */
 						);
+#else
+	musb_writeb(regs, MUSB_POWER,  MUSB_POWER_HSENAB
+						/* ENSUSPEND wedges tusb */
+						/* | MUSB_POWER_ENSUSPEND */
+						);
+#endif
 
 	musb->is_active = 0;
 	devctl = musb_readb(regs, MUSB_DEVCTL);
@@ -1096,6 +1138,7 @@ static struct fifo_cfg __initdata mode_4
 };
 
 
+#ifndef CONFIG_UBICOM32
 /*
  * configure a fifo; for non-shared endpoints, this may be called
  * once for a tx fifo and once for an rx fifo.
@@ -1255,7 +1298,7 @@ static int __init ep_config_from_table(s
 
 	return 0;
 }
-
+#endif /* CONFIG_UBICOM32 */
 
 /*
  * ep_config_from_hw - when MUSB_C_DYNFIFO_DEF is false
@@ -1271,6 +1314,11 @@ static int __init ep_config_from_hw(stru
 	DBG(2, "<== static silicon ep config\n");
 
 	/* FIXME pick up ep0 maxpacket size */
+#ifdef CONFIG_UBICOM32
+	/* set ep0 to shared_fifo, otherwise urb will be put to out_qh but ep0_irq try to get the urb from in_qh*/
+	hw_ep = musb->endpoints;
+	hw_ep->is_shared_fifo = true;
+#endif
 
 	for (epnum = 1; epnum < musb->config->num_eps; epnum++) {
 		musb_ep_select(mbase, epnum);
@@ -1291,14 +1339,27 @@ static int __init ep_config_from_hw(stru
 		/* REVISIT:  this algorithm is lazy, we should at least
 		 * try to pick a double buffered endpoint.
 		 */
+#ifndef CONFIG_UBICOM32
 		if (musb->bulk_ep)
 			continue;
 		musb->bulk_ep = hw_ep;
+#else
+		if ((musb->bulk_ep_in) && (musb->bulk_ep_out))
+			continue;
+		/* Save theEP with 1024 Bytes FIFO for ISO */
+		if(hw_ep->max_packet_sz_tx == 512) {
+			if (!musb->bulk_ep_in) {
+				musb->bulk_ep_in = hw_ep;
+			} else if (!musb->bulk_ep_out) {
+				musb->bulk_ep_out = hw_ep;
+			}
+		}
+#endif /* CONFIG_UBICOM32 */
 #endif
 	}
 
 #ifdef CONFIG_USB_MUSB_HDRC_HCD
-	if (!musb->bulk_ep) {
+	if ((!musb->bulk_ep_in) || (!musb->bulk_ep_out)) {
 		pr_debug("%s: missing bulk\n", musb_driver_name);
 		return -EINVAL;
 	}
@@ -1407,12 +1468,16 @@ static int __init musb_core_init(u16 mus
 	musb->epmask = 1;
 
 	if (reg & MUSB_CONFIGDATA_DYNFIFO) {
+#ifndef CONFIG_UBICOM32
 		if (musb->config->dyn_fifo)
 			status = ep_config_from_table(musb);
-		else {
+		else
+#endif
+		{
 			ERR("reconfigure software for Dynamic FIFOs\n");
 			status = -ENODEV;
 		}
+
 	} else {
 		if (!musb->config->dyn_fifo)
 			status = ep_config_from_hw(musb);
@@ -1476,8 +1541,8 @@ static int __init musb_core_init(u16 mus
 
 /*-------------------------------------------------------------------------*/
 
-#if defined(CONFIG_ARCH_OMAP2430) || defined(CONFIG_ARCH_OMAP3430)
-
+#if defined(CONFIG_ARCH_OMAP2430) || defined(CONFIG_ARCH_OMAP3430) || defined(CONFIG_UBICOM32)
+static u32_t musb_int_count = 0;
 static irqreturn_t generic_interrupt(int irq, void *__hci)
 {
 	unsigned long	flags;
@@ -1486,10 +1551,17 @@ static irqreturn_t generic_interrupt(int
 
 	spin_lock_irqsave(&musb->lock, flags);
 
+#ifndef CONFIG_UBICOM32
 	musb->int_usb = musb_readb(musb->mregs, MUSB_INTRUSB);
 	musb->int_tx = musb_readw(musb->mregs, MUSB_INTRTX);
 	musb->int_rx = musb_readw(musb->mregs, MUSB_INTRRX);
+#else
+	musb_read_int_status(&musb->int_usb, &musb->int_tx, &musb->int_rx);
+	//ubi32_usb_int_clr();
+	musb_int_count++;
+#endif
 
+	DBG(4, "usb %x, tx %x, rx %x", musb->int_usb, musb->int_tx, musb->int_rx);
 	if (musb->int_usb || musb->int_tx || musb->int_rx)
 		retval = musb_interrupt(musb);
 
@@ -2241,6 +2313,10 @@ static struct platform_driver musb_drive
 
 static int __init musb_init(void)
 {
+#ifdef CONFIG_UBICOM32
+	ubi32_usb_init();
+#endif
+
 #ifdef CONFIG_USB_MUSB_HDRC_HCD
 	if (usb_disabled())
 		return 0;
--- a/drivers/usb/musb/musb_core.h
+++ b/drivers/usb/musb/musb_core.h
@@ -339,7 +339,12 @@ struct musb {
 	 * queue until it completes or NAKs too much; then we try the next
 	 * endpoint.
 	 */
+#ifdef CONFIG_UBICOM32
+	struct musb_hw_ep	*bulk_ep_in;
+	struct musb_hw_ep	*bulk_ep_out;
+#else
 	struct musb_hw_ep	*bulk_ep;
+#endif
 
 	struct list_head	control;	/* of musb_qh */
 	struct list_head	in_bulk;	/* of musb_qh */
--- a/drivers/usb/musb/musb_gadget.c
+++ b/drivers/usb/musb/musb_gadget.c
@@ -434,7 +434,7 @@ void musb_g_tx(struct musb *musb, u8 epn
 		 * probably rates reporting as a host error
 		 */
 		if (csr & MUSB_TXCSR_P_SENTSTALL) {
-			csr |= MUSB_TXCSR_P_WZC_BITS;
+			csr &= ~(MUSB_TXCSR_P_WZC_BITS);
 			csr &= ~MUSB_TXCSR_P_SENTSTALL;
 			musb_writew(epio, MUSB_TXCSR, csr);
 			break;
@@ -442,7 +442,7 @@ void musb_g_tx(struct musb *musb, u8 epn
 
 		if (csr & MUSB_TXCSR_P_UNDERRUN) {
 			/* we NAKed, no big deal ... little reason to care */
-			csr |= MUSB_TXCSR_P_WZC_BITS;
+			csr &= ~(MUSB_TXCSR_P_WZC_BITS);
 			csr &= ~(MUSB_TXCSR_P_UNDERRUN
 					| MUSB_TXCSR_TXPKTRDY);
 			musb_writew(epio, MUSB_TXCSR, csr);
@@ -577,12 +577,18 @@ static void rxstate(struct musb *musb, s
 {
 	const u8		epnum = req->epnum;
 	struct usb_request	*request = &req->request;
-	struct musb_ep		*musb_ep = &musb->endpoints[epnum].ep_out;
+	struct musb_ep		*musb_ep = NULL;
 	void __iomem		*epio = musb->endpoints[epnum].regs;
-	unsigned		fifo_count = 0;
-	u16			len = musb_ep->packet_sz;
+	u16			fifo_count = 0;
+	u16			len = 0;
 	u16			csr = musb_readw(epio, MUSB_RXCSR);
 
+	if (musb->endpoints[epnum].is_shared_fifo)
+		musb_ep = &musb->endpoints[epnum].ep_in;
+	else
+		musb_ep = &musb->endpoints[epnum].ep_out;
+	len =  musb_ep->packet_sz;
+
 	/* We shouldn't get here while DMA is active, but we do... */
 	if (dma_channel_status(musb_ep->dma) == MUSB_DMA_STATUS_BUSY) {
 		DBG(4, "DMA pending...\n");
@@ -730,7 +736,7 @@ static void rxstate(struct musb *musb, s
 			 */
 
 			/* ack the read! */
-			csr |= MUSB_RXCSR_P_WZC_BITS;
+			csr &= ~MUSB_RXCSR_P_WZC_BITS;
 			csr &= ~MUSB_RXCSR_RXPKTRDY;
 			musb_writew(epio, MUSB_RXCSR, csr);
 		}
@@ -749,10 +755,15 @@ void musb_g_rx(struct musb *musb, u8 epn
 	u16			csr;
 	struct usb_request	*request;
 	void __iomem		*mbase = musb->mregs;
-	struct musb_ep		*musb_ep = &musb->endpoints[epnum].ep_out;
+	struct musb_ep		*musb_ep = NULL;
 	void __iomem		*epio = musb->endpoints[epnum].regs;
 	struct dma_channel	*dma;
 
+	if (musb->endpoints[epnum].is_shared_fifo)
+		musb_ep = &musb->endpoints[epnum].ep_in;
+	else
+		musb_ep = &musb->endpoints[epnum].ep_out;
+
 	musb_ep_select(mbase, epnum);
 
 	request = next_request(musb_ep);
@@ -1756,7 +1767,9 @@ int usb_gadget_register_driver(struct us
 			}
 		}
 	}
-
+#ifndef CONFIG_USB_MUSB_OTG
+	musb_pullup(musb, 1);
+#endif
 	return retval;
 }
 EXPORT_SYMBOL(usb_gadget_register_driver);
--- a/drivers/usb/musb/musb_gadget_ep0.c
+++ b/drivers/usb/musb/musb_gadget_ep0.c
@@ -241,14 +241,14 @@ __acquires(musb->lock)
 		case USB_REQ_SET_ADDRESS:
 			/* change it after the status stage */
 			musb->set_address = true;
-			musb->address = (u8) (ctrlrequest->wValue & 0x7f);
+			musb->address = (u8) (le16_to_cpu(ctrlrequest->wValue) & 0x7f);
 			handled = 1;
 			break;
 
 		case USB_REQ_CLEAR_FEATURE:
 			switch (recip) {
 			case USB_RECIP_DEVICE:
-				if (ctrlrequest->wValue
+				if (le16_to_cpu(ctrlrequest->wValue)
 						!= USB_DEVICE_REMOTE_WAKEUP)
 					break;
 				musb->may_wakeup = 0;
@@ -262,8 +262,8 @@ __acquires(musb->lock)
 
 				if (num == 0
 						|| num >= MUSB_C_NUM_EPS
-						|| ctrlrequest->wValue
-							!= USB_ENDPOINT_HALT)
+						|| le16_to_cpu(ctrlrequest->wValue
+							!= USB_ENDPOINT_HALT))
 					break;
 
 				if (ctrlrequest->wIndex & USB_DIR_IN)
@@ -293,7 +293,7 @@ __acquires(musb->lock)
 			switch (recip) {
 			case USB_RECIP_DEVICE:
 				handled = 1;
-				switch (ctrlrequest->wValue) {
+				switch (le16_to_cpu(ctrlrequest->wValue)) {
 				case USB_DEVICE_REMOTE_WAKEUP:
 					musb->may_wakeup = 1;
 					break;
@@ -375,8 +375,8 @@ stall:
 
 				if (epnum == 0
 						|| epnum >= MUSB_C_NUM_EPS
-						|| ctrlrequest->wValue
-							!= USB_ENDPOINT_HALT)
+						|| le16_to_cpu(ctrlrequest->wValue
+							!= USB_ENDPOINT_HALT))
 					break;
 
 				ep = musb->endpoints + epnum;
--- a/drivers/usb/musb/musb_host.c
+++ b/drivers/usb/musb/musb_host.c
@@ -160,7 +160,11 @@ static inline void musb_h_tx_start(struc
 	/* NOTE: no locks here; caller should lock and select EP */
 	if (ep->epnum) {
 		txcsr = musb_readw(ep->regs, MUSB_TXCSR);
+#ifndef CONFIG_UBICOM32
 		txcsr |= MUSB_TXCSR_TXPKTRDY | MUSB_TXCSR_H_WZC_BITS;
+#else
+		txcsr |= (MUSB_TXCSR_TXPKTRDY & (~MUSB_TXCSR_H_WZC_BITS));
+#endif
 		musb_writew(ep->regs, MUSB_TXCSR, txcsr);
 	} else {
 		txcsr = MUSB_CSR0_H_SETUPPKT | MUSB_CSR0_TXPKTRDY;
@@ -235,6 +239,8 @@ musb_start_urb(struct musb *musb, int is
 		break;
 	default:		/* bulk, interrupt */
 		/* actual_length may be nonzero on retry paths */
+		if (urb->actual_length)
+			DBG(3 ,"musb_start_urb: URB %p retried, len: %d\n", urb, urb->actual_length);
 		buf = urb->transfer_buffer + urb->actual_length;
 		len = urb->transfer_buffer_length - urb->actual_length;
 	}
@@ -532,7 +538,11 @@ musb_host_packet_rx(struct musb *musb, s
 	musb_read_fifo(hw_ep, length, buf);
 
 	csr = musb_readw(epio, MUSB_RXCSR);
+#ifndef CONFIG_UBICOM32
 	csr |= MUSB_RXCSR_H_WZC_BITS;
+#else
+	csr &= ~MUSB_RXCSR_H_WZC_BITS;
+#endif
 	if (unlikely(do_flush))
 		musb_h_flush_rxfifo(hw_ep, csr);
 	else {
@@ -566,6 +576,7 @@ musb_rx_reinit(struct musb *musb, struct
 
 	/* if programmed for Tx, put it in RX mode */
 	if (ep->is_shared_fifo) {
+#ifndef  CONFIG_UBICOM32
 		csr = musb_readw(ep->regs, MUSB_TXCSR);
 		if (csr & MUSB_TXCSR_MODE) {
 			musb_h_tx_flush_fifo(ep);
@@ -580,7 +591,18 @@ musb_rx_reinit(struct musb *musb, struct
 		 */
 		if (csr & MUSB_TXCSR_DMAMODE)
 			musb_writew(ep->regs, MUSB_TXCSR, MUSB_TXCSR_DMAMODE);
+
+#else
+		/* clear mode (and everything else) to enable Rx */
 		musb_writew(ep->regs, MUSB_TXCSR, 0);
+		/* scrub all previous state, clearing toggle */
+		csr = musb_readw(ep->regs, MUSB_RXCSR);
+		if (csr & MUSB_RXCSR_RXPKTRDY)
+			WARNING("rx%d, packet/%d ready?\n", ep->epnum,
+				musb_readw(ep->regs, MUSB_RXCOUNT));
+
+		musb_h_flush_rxfifo(ep, MUSB_RXCSR_CLRDATATOG);
+#endif
 
 	/* scrub all previous state, clearing toggle */
 	} else {
@@ -1108,6 +1130,16 @@ void musb_host_tx(struct musb *musb, u8 
 	void __iomem		*mbase = musb->mregs;
 	struct dma_channel	*dma;
 
+#ifdef CONFIG_UBICOM32
+	if (hw_ep->is_shared_fifo) {
+		qh = hw_ep->in_qh;
+	}
+#ifdef CONFIG_USB_SERIAL_SIERRAWIRELESS
+	printk(KERN_DEBUG "OUT/TX%d end, csr %04x%s\n", epnum, tx_csr,
+			dma ? ", dma" : "");
+#endif
+#endif
+
 	musb_ep_select(mbase, epnum);
 	tx_csr = musb_readw(epio, MUSB_TXCSR);
 
@@ -1148,9 +1180,14 @@ void musb_host_tx(struct musb *musb, u8 
 		 * we have a candidate... NAKing is *NOT* an error
 		 */
 		musb_ep_select(mbase, epnum);
+#ifndef CONFIG_UBICOM32
 		musb_writew(epio, MUSB_TXCSR,
 				MUSB_TXCSR_H_WZC_BITS
 				| MUSB_TXCSR_TXPKTRDY);
+#else
+		musb_writew(epio, MUSB_TXCSR,
+				 MUSB_TXCSR_TXPKTRDY);
+#endif
 		return;
 	}
 
@@ -1324,8 +1361,14 @@ void musb_host_tx(struct musb *musb, u8 
 	qh->segsize = length;
 
 	musb_ep_select(mbase, epnum);
+#ifndef CONFIG_UBICOM32
+	musb_writew(epio, MUSB_TXCSR,
+		    MUSB_TXCSR_H_WZC_BITS | MUSB_TXCSR_TXPKTRDY);
+#else
 	musb_writew(epio, MUSB_TXCSR,
-			MUSB_TXCSR_H_WZC_BITS | MUSB_TXCSR_TXPKTRDY);
+		    MUSB_TXCSR_MODE | MUSB_TXCSR_TXPKTRDY);
+#endif
+
 }
 
 
@@ -1385,7 +1428,11 @@ static void musb_bulk_rx_nak_timeout(str
 
 	/* clear nak timeout bit */
 	rx_csr = musb_readw(epio, MUSB_RXCSR);
+#ifndef CONFIG_UBICOM32
 	rx_csr |= MUSB_RXCSR_H_WZC_BITS;
+#else
+	rx_csr &= ~MUSB_RXCSR_H_WZC_BITS;
+#endif
 	rx_csr &= ~MUSB_RXCSR_DATAERROR;
 	musb_writew(epio, MUSB_RXCSR, rx_csr);
 
@@ -1454,6 +1501,13 @@ void musb_host_rx(struct musb *musb, u8 
 
 	pipe = urb->pipe;
 
+#ifdef CONFIG_UBICOM32
+#ifdef CONFIG_USB_SERIAL_SIERRAWIRELESS
+		printk(KERN_DEBUG  "RXCSR%d %04x, reqpkt, len %zu%s\n", epnum, rx_csr,
+				xfer_len, dma ? ", dma" : "");
+#endif
+#endif
+
 	DBG(5, "<== hw %d rxcsr %04x, urb actual %d (+dma %zu)\n",
 		epnum, rx_csr, urb->actual_length,
 		dma ? dma->actual_len : 0);
@@ -1492,8 +1546,15 @@ void musb_host_rx(struct musb *musb, u8 
 				return;
 			}
 			musb_ep_select(mbase, epnum);
+#ifndef CONFIG_UBICOM32
 			rx_csr |= MUSB_RXCSR_H_WZC_BITS;
 			rx_csr &= ~MUSB_RXCSR_DATAERROR;
+#else
+			/* NEED TO EVALUATE CHANGE */
+			rx_csr &= ~MUSB_RXCSR_H_WZC_BITS;
+			rx_csr &= ~MUSB_RXCSR_DATAERROR;
+//			musb_writew(epio, MUSB_RXCSR, (~(MUSB_RXCSR_H_WZC_BITS))| MUSB_RXCSR_H_REQPKT);
+#endif
 			musb_writew(epio, MUSB_RXCSR, rx_csr);
 
 			goto finish;
@@ -1554,8 +1615,13 @@ void musb_host_rx(struct musb *musb, u8 
 		rx_csr &= ~MUSB_RXCSR_H_REQPKT;
 
 		musb_ep_select(mbase, epnum);
+#ifndef CONFIG_UBICOM32
 		musb_writew(epio, MUSB_RXCSR,
 				MUSB_RXCSR_H_WZC_BITS | rx_csr);
+#else
+		musb_writew(epio, MUSB_RXCSR,
+				(~MUSB_RXCSR_H_WZC_BITS) & rx_csr);
+#endif
 	}
 #endif
 	if (dma && (rx_csr & MUSB_RXCSR_DMAENAB)) {
@@ -1585,7 +1651,7 @@ void musb_host_rx(struct musb *musb, u8 
 			else
 				done = false;
 
-		} else  {
+		} else {
 		/* done if urb buffer is full or short packet is recd */
 		done = (urb->actual_length + xfer_len >=
 				urb->transfer_buffer_length
@@ -1799,7 +1865,11 @@ static int musb_schedule(
 		if (musb_ep_get_qh(hw_ep, is_in) != NULL)
 			continue;
 
+#ifndef CONFIG_UBICOM32
 		if (hw_ep == musb->bulk_ep)
+#else
+		if ((hw_ep == musb->bulk_ep_in) || (hw_ep == musb->bulk_ep_out)) /* Ubicom */
+#endif
 			continue;
 
 		if (is_in)
@@ -1813,7 +1883,14 @@ static int musb_schedule(
 			best_end = epnum;
 		}
 	}
+
+#ifdef CONFIG_UBICOM32
+	if (((best_diff >= qh->maxpacket)) && ((qh->type == USB_ENDPOINT_XFER_BULK) && (!is_in)))
+		best_end = -1;
+#endif
+
 	/* use bulk reserved ep1 if no other ep is free */
+#ifndef CONFIG_UBICOM32
 	if (best_end < 0 && qh->type == USB_ENDPOINT_XFER_BULK) {
 		hw_ep = musb->bulk_ep;
 		if (is_in)
@@ -1835,6 +1912,22 @@ static int musb_schedule(
 	} else if (best_end < 0) {
 		return -ENOSPC;
 	}
+#else
+	if (best_end < 0 && qh->type == USB_ENDPOINT_XFER_BULK) {
+		/* hw_ep = musb->bulk_ep; */
+		if (is_in) {
+			head = &musb->in_bulk;
+			hw_ep = musb->bulk_ep_in; /* UBICOM */
+		}
+		else {
+			head = &musb->out_bulk;
+			hw_ep = musb->bulk_ep_out; /* UBICOM */
+		}
+		goto success;
+	} else if (best_end < 0) {
+		return -ENOSPC;
+	}
+#endif
 
 	idle = 1;
 	qh->mux = 0;
@@ -1846,6 +1939,13 @@ success:
 		list_add_tail(&qh->ring, head);
 		qh->mux = 1;
 	}
+	/*
+	 * It's not make sense to set NAK timeout when qh->mux = 0,
+	 * There is nothing else to schedule
+	 */
+	if ((qh->type == USB_ENDPOINT_XFER_BULK) && (qh->mux == 0))
+		qh->intv_reg = 0;
+
 	qh->hw_ep = hw_ep;
 	qh->hep->hcpriv = qh;
 	if (idle)
@@ -1964,6 +2064,15 @@ static int musb_urb_enqueue(
 		/* ISO always uses logarithmic encoding */
 		interval = min_t(u8, epd->bInterval, 16);
 		break;
+#ifdef COMFIG_UBICOM32
+	case USB_ENDPOINT_XFER_BULK:
+		 if (epd->bEndpointAddress & USB_ENDPOINT_DIR_MASK)
+			interval = (USB_SPEED_HIGH == urb->dev->speed) ? 16: 2;
+		 else
+			interval = 0;
+		 break;
+#endif
+
 	default:
 		/* REVISIT we actually want to use NAK limits, hinting to the
 		 * transfer scheduling logic to try some other qh, e.g. try
--- a/drivers/usb/musb/musb_io.h
+++ b/drivers/usb/musb/musb_io.h
@@ -58,6 +58,7 @@ static inline void writesb(const void __
 
 #ifndef CONFIG_BLACKFIN
 
+#ifndef CONFIG_UBICOM32
 /* NOTE:  these offsets are all in bytes */
 
 static inline u16 musb_readw(const void __iomem *addr, unsigned offset)
@@ -72,7 +73,37 @@ static inline void musb_writew(void __io
 
 static inline void musb_writel(void __iomem *addr, unsigned offset, u32 data)
 	{ __raw_writel(data, addr + offset); }
+#else
+#include <asm/ubicom32-tio.h>
+static inline u16 musb_readw(const void __iomem *addr, unsigned offset)
+{
+        u16 data;
+        usb_tio_read_u16((u32)(addr + offset), &data);
+        return data;
+}
 
+static inline u8 musb_readb(const void __iomem *addr, unsigned offset)
+{
+        u8 data;
+        usb_tio_read_u8((u32)(addr + offset), &data);
+        return data;
+}
+
+static inline void musb_writew(void __iomem *addr, unsigned offset, u16 data)
+{
+        usb_tio_write_u16((u32)(addr + offset), data);
+}
+
+static inline void musb_writeb(void __iomem *addr, unsigned offset, u8 data)
+{
+        usb_tio_write_u8((u32)(addr + offset), data);
+}
+
+static inline void  musb_read_int_status(u8_t *int_usb, u16_t *int_tx, u16_t *int_rx)
+{
+	return usb_tio_read_int_status(int_usb, int_tx, int_rx);
+}
+#endif /* CONFIG_UBICOM32 */
 
 #ifdef CONFIG_USB_TUSB6010
 
@@ -106,7 +137,7 @@ static inline void musb_writeb(void __io
 	__raw_writew(tmp, addr + (offset & ~1));
 }
 
-#else
+#elif !defined(CONFIG_UBICOM32)
 
 static inline u8 musb_readb(const void __iomem *addr, unsigned offset)
 	{ return __raw_readb(addr + offset); }
--- a/drivers/usb/musb/musb_regs.h
+++ b/drivers/usb/musb/musb_regs.h
@@ -167,6 +167,7 @@
 	(MUSB_TXCSR_H_NAKTIMEOUT | MUSB_TXCSR_H_RXSTALL \
 	| MUSB_TXCSR_H_ERROR | MUSB_TXCSR_FIFONOTEMPTY)
 
+
 /* RXCSR in Peripheral and Host mode */
 #define MUSB_RXCSR_AUTOCLEAR		0x8000
 #define MUSB_RXCSR_DMAENAB		0x2000
--- a/drivers/video/backlight/Kconfig
+++ b/drivers/video/backlight/Kconfig
@@ -100,6 +100,63 @@ config LCD_HP700
 	  If you have an HP Jornada 700 series handheld (710/720/728)
 	  say Y to enable LCD control driver.
 
+config LCD_UBICOM32POWER
+	tristate "Ubicom LCD power Driver"
+	depends on LCD_CLASS_DEVICE && UBICOM32
+	default n
+	help
+	  If you have a Ubicom32 based system with an LCD panel that requires
+	  power control, say Y to enable the power control driver for it.
+
+config LCD_UBICOM32
+	tristate "Ubicom Backlight Driver"
+	depends on LCD_CLASS_DEVICE && UBICOM32
+	default n
+	help
+	  This driver takes care of initialization of LCD panels with
+	  built in controllers.
+
+menu "Ubicom32 LCD Panel Support"
+	depends on UBICOM32 && LCD_UBICOM32
+
+config LCD_UBICOM32_TFT2N0369E_P
+	bool "TFT2N0369E (Portrait)"
+	default n
+	help
+	  Support for TFT2N0369 in portrait mode
+
+config LCD_UBICOM32_TFT2N0369E_L
+	bool "TFT2N0369E (Landscape)"
+	default n
+	help
+	  Support for TFT2N0369 in landscape mode
+
+config LCD_UBICOM32_CFAF240320KTTS
+	bool "CFAF240320KTTS"
+	default n
+	help
+	  Support for CFAF240320KTTS
+
+config LCD_UBICOM32_CFAF240320KTTS_180
+	bool "CFAF240320KTTS (180 rotation)"
+	default n
+	help
+	  Support for CFAF240320KTTS rotated 180 degrees
+
+config LCD_UBICOM32_CFAF240320D
+	bool "CFAF240320D"
+	default n
+	help
+	  Support for CFAF240320D
+
+config LCD_UBICOM32_CFAF320240F
+	bool "CFAF320240F"
+	default n
+	help
+	  Support for CFAF320240F
+
+endmenu
+
 #
 # Backlight
 #
@@ -262,3 +319,11 @@ config BACKLIGHT_ADP5520
 	  To compile this driver as a module, choose M here: the module will
 	  be called adp5520_bl.
 
+config BACKLIGHT_UBICOM32
+	tristate "Ubicom Backlight Driver"
+	depends on BACKLIGHT_CLASS_DEVICE && UBICOM32
+	default n
+	help
+	  If you have a Ubicom32 based system with a backlight say Y to enable the
+	  backlight driver.
+
--- a/drivers/video/backlight/Makefile
+++ b/drivers/video/backlight/Makefile
@@ -10,6 +10,9 @@ obj-$(CONFIG_LCD_PLATFORM)	   += platfor
 obj-$(CONFIG_LCD_VGG2432A4)	   += vgg2432a4.o
 obj-$(CONFIG_LCD_TDO24M)	   += tdo24m.o
 obj-$(CONFIG_LCD_TOSA)		   += tosa_lcd.o
+obj-$(CONFIG_LCD_LTV350QV)	   += ltv350qv.o
+obj-$(CONFIG_LCD_UBICOM32POWER)	   += ubicom32lcdpower.o
+obj-$(CONFIG_LCD_UBICOM32)	   += ubicom32lcd.o
 
 obj-$(CONFIG_BACKLIGHT_CLASS_DEVICE) += backlight.o
 obj-$(CONFIG_BACKLIGHT_ATMEL_PWM)    += atmel-pwm-bl.o
@@ -28,4 +31,4 @@ obj-$(CONFIG_BACKLIGHT_SAHARA)	+= kb3886
 obj-$(CONFIG_BACKLIGHT_WM831X)	+= wm831x_bl.o
 obj-$(CONFIG_BACKLIGHT_ADX)    += adx_bl.o
 obj-$(CONFIG_BACKLIGHT_ADP5520)	+= adp5520_bl.o
-
+obj-$(CONFIG_BACKLIGHT_UBICOM32) += ubicom32bl.o
--- a/drivers/video/Kconfig
+++ b/drivers/video/Kconfig
@@ -611,6 +611,50 @@ config FB_BFIN_T350MCQB
 	 This display is a QVGA 320x240 24-bit RGB display interfaced by an 8-bit wide PPI
 	 It uses PPI[0..7] PPI_FS1, PPI_FS2 and PPI_CLK.
 
+config FB_UBICOM32
+	tristate "Ubicom32 Frame Buffer driver"
+	depends on FB && UBICOM32
+	select FB_CFB_FILLRECT
+	select FB_CFB_COPYAREA
+	select FB_CFB_IMAGEBLIT
+	select FONT_6x11 if FRAMEBUFFER_CONSOLE
+	help
+	 This is the framebuffer device driver for the Ubicom32 architecture.
+	 You can configure video memory by using kernel command line parameters, for example:
+		video=ubicomfb:vram_size=512,init_value=0xffff
+
+config FB_UBICOM32_PLIO80
+	tristate "Ubicom32 80 Bus PLIO Frame Buffer driver"
+	depends on FB && UBICOM32
+	select FB_CFB_FILLRECT
+	select FB_CFB_COPYAREA
+	select FB_CFB_IMAGEBLIT
+	select FONT_6x11 if FRAMEBUFFER_CONSOLE
+	select UBICOM32_PLIO
+	help
+	 This is a framebuffer device driver for the Ubicom32 architecture.
+	 You can configure the xres, yres and vram size (in kilobytes) by using
+	 kernel command line parameters, for example:
+		video=ubicom32vfb:xres=320,yres=240,vram_size=512
+
+config FB_UBICOM32_VIRTUAL
+	tristate "Ubicom32 Virtual Frame Buffer driver"
+	depends on FB && UBICOM32
+	select FB_CFB_FILLRECT
+	select FB_CFB_COPYAREA
+	select FB_CFB_IMAGEBLIT
+	select FONT_6x11 if FRAMEBUFFER_CONSOLE
+	help
+	 This is a virtual framebuffer device driver for the Ubicom32 architecture.
+	 You can configure the xres, yres and vram size (in kilobytes) by using
+	 kernel command line parameters, for example:
+		video=ubicom32vfb:xres=320,yres=240,vram_size=512
+
+config FB_UBICOM32_VIRTUAL_NOAUTO
+	bool "Do not automatically load"
+	depends on FB_UBICOM32_VIRTUAL
+	help
+	 Select this option to prevent the VFB from automatically loading at boot.
 
 config FB_STI
 	tristate "HP STI frame buffer device support"
--- a/drivers/video/Makefile
+++ b/drivers/video/Makefile
@@ -140,6 +140,10 @@ obj-$(CONFIG_FB_BFIN_T350MCQB)	  += bfin
 obj-$(CONFIG_FB_MX3)		  += mx3fb.o
 obj-$(CONFIG_FB_DA8XX)		  += da8xx-fb.o
 
+obj-$(CONFIG_FB_UBICOM32)         += ubicom32fb.o
+obj-$(CONFIG_FB_UBICOM32_PLIO80)  += ubicom32plio80.o
+obj-$(CONFIG_FB_UBICOM32_VIRTUAL) += ubicom32vfb.o
+
 # the test framebuffer is last
 obj-$(CONFIG_FB_VIRTUAL)          += vfb.o
 
--- a/drivers/watchdog/Kconfig
+++ b/drivers/watchdog/Kconfig
@@ -973,6 +973,19 @@ config WATCHDOG_RIO
 	  machines.  The watchdog timeout period is normally one minute but
 	  can be changed with a boot-time parameter.
 
+# Ubicom32
+
+config UBI32_WDT
+	tristate "Ubicom32 Hardware Watchdog support"
+	depends on UBICOM32
+	---help---
+	  If you say yes here you will get support for the Ubicom32 On-Chip
+	  Watchdog Timer. If you have one of these processors and wish to
+	  have watchdog support enabled, say Y, otherwise say N.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called ubi32_wdt.
+
 # XTENSA Architecture
 
 #
--- a/drivers/watchdog/Makefile
+++ b/drivers/watchdog/Makefile
@@ -139,6 +139,9 @@ obj-$(CONFIG_SH_WDT) += shwdt.o
 obj-$(CONFIG_WATCHDOG_RIO)		+= riowd.o
 obj-$(CONFIG_WATCHDOG_CP1XXX)		+= cpwd.o
 
+# Ubicom32 Architecture
+obj-$(CONFIG_UBI32_WDT)			+= ubi32_wdt.o
+
 # XTENSA Architecture
 
 # Architecture Independant
--- a/fs/binfmt_flat.c
+++ b/fs/binfmt_flat.c
@@ -67,6 +67,11 @@
 #define FLAT_DATA_ALIGN	(sizeof(void *))
 #endif
 
+#ifndef ARCH_FLAT_ALIGN
+#undef FLAT_DATA_ALIGN
+#define FLAT_DATA_ALIGN	ARCH_FLAT_ALIGN
+#endif
+
 #define RELOC_FAILED 0xff00ff01		/* Relocation incorrect somewhere */
 #define UNLOADED_LIB 0x7ff000ff		/* Placeholder for unused library */
 
@@ -434,6 +439,7 @@ static int load_flat_file(struct linux_b
 	loff_t fpos;
 	unsigned long start_code, end_code;
 	int ret;
+	int flush_happened = 0;
 
 	hdr = ((struct flat_hdr *) bprm->buf);		/* exec-header */
 	inode = bprm->file->f_path.dentry->d_inode;
@@ -520,6 +526,7 @@ static int load_flat_file(struct linux_b
 		/* OK, This is the point of no return */
 		set_personality(PER_LINUX_32BIT);
 		setup_new_exec(bprm);
+		flush_happened = 1;
 	}
 
 	/*
@@ -534,6 +541,12 @@ static int load_flat_file(struct linux_b
 	 * it all together.
 	 */
 	if ((flags & (FLAT_FLAG_RAM|FLAT_FLAG_GZIP)) == 0) {
+
+#ifdef ARCH_FLAT_ALIGN_TEXT
+		printk("Unable to mmap rom with ARCH alignment requirements\n");
+		ret = -ENOEXEC;
+		goto err;
+#endif
 		/*
 		 * this should give us a ROM ptr,  but if it doesn't we don't
 		 * really care
@@ -552,7 +565,7 @@ static int load_flat_file(struct linux_b
 			goto err;
 		}
 
-		len = data_len + extra + MAX_SHARED_LIBS * sizeof(unsigned long);
+		len = data_len + extra + ALIGN(MAX_SHARED_LIBS * sizeof(unsigned long), FLAT_DATA_ALIGN);
 		len = PAGE_ALIGN(len);
 		down_write(&current->mm->mmap_sem);
 		realdatastart = do_mmap(0, 0, len,
@@ -571,6 +584,7 @@ static int load_flat_file(struct linux_b
 		datapos = ALIGN(realdatastart +
 				MAX_SHARED_LIBS * sizeof(unsigned long),
 				FLAT_DATA_ALIGN);
+		//datapos = realdatastart + ALIGN(MAX_SHARED_LIBS * sizeof(unsigned long), ARCH_FLAT_ALIGN);
 
 		DBG_FLT("BINFMT_FLAT: Allocated data+bss+stack (%d bytes): %x\n",
 				(int)(data_len + bss_len + stack_len), (int)datapos);
@@ -599,7 +613,11 @@ static int load_flat_file(struct linux_b
 		memp_size = len;
 	} else {
 
-		len = text_len + data_len + extra + MAX_SHARED_LIBS * sizeof(unsigned long);
+		len = text_len + data_len + extra + ALIGN(MAX_SHARED_LIBS * sizeof(unsigned long), FLAT_DATA_ALIGN);
+#ifdef ARCH_FLAT_ALIGN_TEXT
+		/* Reserve space for the text alignment. */
+		len += FLAT_DATA_ALIGN;
+#endif
 		len = PAGE_ALIGN(len);
 		down_write(&current->mm->mmap_sem);
 		textpos = do_mmap(0, 0, len,
@@ -615,10 +633,17 @@ static int load_flat_file(struct linux_b
 			goto err;
 		}
 
+		memp = textpos;
+#ifdef ARCH_FLAT_ALIGN_TEXT
+		textpos = ALIGN(textpos + sizeof(struct flat_hdr), FLAT_DATA_ALIGN) - sizeof(struct flat_hdr);
+#endif
 		realdatastart = textpos + ntohl(hdr->data_start);
 		datapos = ALIGN(realdatastart +
 				MAX_SHARED_LIBS * sizeof(unsigned long),
 				FLAT_DATA_ALIGN);
+//		datapos = realdatastart + ALIGN(MAX_SHARED_LIBS * sizeof(unsigned long), ARCH_FLAT_ALIGN);
+//		reloc = (unsigned long *) (textpos + ntohl(hdr->reloc_start) +
+//					   ALIGN(MAX_SHARED_LIBS * sizeof(unsigned long), ARCH_FLAT_ALIGN));
 
 		reloc = (unsigned long *)
 			(datapos + (ntohl(hdr->reloc_start) - text_len));
@@ -658,7 +683,7 @@ static int load_flat_file(struct linux_b
 		}
 		if (IS_ERR_VALUE(result)) {
 			printk("Unable to read code+data+bss, errno %d\n",(int)-result);
-			do_munmap(current->mm, textpos, text_len + data_len + extra +
+			do_munmap(current->mm, memp, text_len + data_len + extra +
 				MAX_SHARED_LIBS * sizeof(unsigned long));
 			ret = result;
 			goto err;
@@ -671,6 +696,9 @@ static int load_flat_file(struct linux_b
 
 	/* The main program needs a little extra setup in the task structure */
 	start_code = textpos + sizeof (struct flat_hdr);
+#ifdef ARCH_FLAT_ALIGN_TEXT
+	BUG_ON(ALIGN(start_code, FLAT_DATA_ALIGN) != start_code);
+#endif
 	end_code = textpos + text_len;
 	if (id == 0) {
 		current->mm->start_code = start_code;
@@ -799,6 +827,13 @@ static int load_flat_file(struct linux_b
 
 	return 0;
 err:
+	if (flush_happened) {
+		/*
+		 * The parent process has already started running. We cannot allow the child to return back to user space
+		 * as this child is still uning the parent stack and 2 will clobber each other. We are going to kill this child.
+		 */
+		do_exit(SIGTERM);
+	}
 	return ret;
 }
 
--- a/fs/Kconfig.binfmt
+++ b/fs/Kconfig.binfmt
@@ -30,7 +30,7 @@ config COMPAT_BINFMT_ELF
 config BINFMT_ELF_FDPIC
 	bool "Kernel support for FDPIC ELF binaries"
 	default y
-	depends on (FRV || BLACKFIN || (SUPERH32 && !MMU))
+	depends on (FRV || BLACKFIN || (SUPERH32 && !MMU) || UBICOM32)
 	help
 	  ELF FDPIC binaries are based on ELF, but allow the individual load
 	  segments of a binary to be located in memory independently of each
--- a/include/asm-generic/resource.h
+++ b/include/asm-generic/resource.h
@@ -69,13 +69,16 @@
 /*
  * boot-time rlimit defaults for the init task:
  */
+#ifndef	CONFIG_ELF_CORE
+#define	CONFIG_USER_ELF_CORE_SIZE	0
+#endif
 #define INIT_RLIMITS							\
 {									\
 	[RLIMIT_CPU]		= {  RLIM_INFINITY,  RLIM_INFINITY },	\
 	[RLIMIT_FSIZE]		= {  RLIM_INFINITY,  RLIM_INFINITY },	\
 	[RLIMIT_DATA]		= {  RLIM_INFINITY,  RLIM_INFINITY },	\
 	[RLIMIT_STACK]		= {       _STK_LIM,   _STK_LIM_MAX },	\
-	[RLIMIT_CORE]		= {              0,  RLIM_INFINITY },	\
+	[RLIMIT_CORE]		= { CONFIG_USER_ELF_CORE_SIZE,  RLIM_INFINITY },	\
 	[RLIMIT_RSS]		= {  RLIM_INFINITY,  RLIM_INFINITY },	\
 	[RLIMIT_NPROC]		= {              0,              0 },	\
 	[RLIMIT_NOFILE]		= {       INR_OPEN,       INR_OPEN },	\
--- a/include/linux/elf-em.h
+++ b/include/linux/elf-em.h
@@ -41,6 +41,7 @@
  * up with a final number.
  */
 #define EM_ALPHA	0x9026
+#define EM_UBICOM32 	        0xde3d	/* Ubicom32; no ABI */
 
 /* Bogus old v850 magic number, used by old tools. */
 #define EM_CYGNUS_V850	0x9080
--- a/include/linux/fb.h
+++ b/include/linux/fb.h
@@ -152,6 +152,10 @@ struct dentry;
 #define FB_ACCEL_PROSAVAGE_DDR  0x8d	/* S3 ProSavage DDR             */
 #define FB_ACCEL_PROSAVAGE_DDRK 0x8e	/* S3 ProSavage DDR-K           */
 
+#define FB_ACCEL_UBICOM32		0x0100	/* Ubicom32			*/
+#define FB_ACCEL_UBICOM32_VFB		0x0101	/* Ubicom32 VFB			*/
+#define FB_ACCEL_UBICOM32_PLIO80	0x0102	/* Ubicom32 PLIO80		*/
+
 struct fb_fix_screeninfo {
 	char id[16];			/* identification string eg "TT Builtin" */
 	unsigned long smem_start;	/* Start of frame buffer mem */
--- a/include/linux/if_ppp.h
+++ b/include/linux/if_ppp.h
@@ -114,14 +114,14 @@ struct pppol2tp_ioc_stats {
 	__u16		tunnel_id;	/* redundant */
 	__u16		session_id;	/* if zero, get tunnel stats */
 	__u32		using_ipsec:1;	/* valid only for session_id == 0 */
-	aligned_u64	tx_packets;
-	aligned_u64	tx_bytes;
-	aligned_u64	tx_errors;
-	aligned_u64	rx_packets;
-	aligned_u64	rx_bytes;
-	aligned_u64	rx_seq_discards;
-	aligned_u64	rx_oos_packets;
-	aligned_u64	rx_errors;
+	__u64	tx_packets;
+	__u64	tx_bytes;
+	__u64	tx_errors;
+	__u64	rx_packets;
+	__u64	rx_bytes;
+	__u64	rx_seq_discards;
+	__u64	rx_oos_packets;
+	__u64	rx_errors;
 };
 
 #define ifr__name       b.ifr_ifrn.ifrn_name
--- a/include/linux/oprofile.h
+++ b/include/linux/oprofile.h
@@ -102,6 +102,8 @@ void oprofile_add_sample(struct pt_regs 
  */
 void oprofile_add_ext_sample(unsigned long pc, struct pt_regs * const regs,
 				unsigned long event, int is_kernel);
+void oprofile_add_ext_sample_cpu(unsigned long pc, struct pt_regs * const regs,
+				unsigned long event, int is_kernel, int cpu);
 
 /* Use this instead when the PC value is not from the regs. Doesn't
  * backtrace. */
--- a/include/linux/serial_core.h
+++ b/include/linux/serial_core.h
@@ -179,6 +179,9 @@
 /* BCM63xx family SoCs */
 #define PORT_BCM63XX	89
 
+/* Ubicom32 */
+#define PORT_UBI32_UARTTIO	87
+
 #ifdef __KERNEL__
 
 #include <linux/compiler.h>
--- a/include/linux/slab.h
+++ b/include/linux/slab.h
@@ -328,4 +328,14 @@ static inline void *kzalloc_node(size_t 
 
 void __init kmem_cache_init_late(void);
 
+struct kmem_cache_size_info {
+	unsigned short page;
+	unsigned short order;
+};
+
+/*
+ * get info on all the memory allocated by slab for this named cache
+ */
+extern int kmem_cache_block_info(char *name, struct kmem_cache_size_info *data, int max_data);
+
 #endif	/* _LINUX_SLAB_H */
--- a/init/Kconfig
+++ b/init/Kconfig
@@ -844,6 +844,12 @@ config ELF_CORE
 	help
 	  Enable support for generating core dumps. Disabling saves about 4k.
 
+config USER_ELF_CORE_SIZE
+	int "user core dump size (10MB to 32MB)"
+	range 10485760 33554432
+	default 16777216
+	depends on ELF_CORE
+
 config PCSPKR_PLATFORM
 	bool "Enable PC-Speaker support" if EMBEDDED
 	depends on ALPHA || X86 || MIPS || PPC_PREP || PPC_CHRP || PPC_PSERIES
--- a/kernel/module.c
+++ b/kernel/module.c
@@ -2945,6 +2945,9 @@ static int m_show(struct seq_file *m, vo
 	/* Used by oprofile and other similar tools. */
 	seq_printf(m, " 0x%p", mod->module_core);
 
+#ifdef ARCH_PROC_MODULES_EXTRA
+	ARCH_PROC_MODULES_EXTRA(m, mod);
+#endif
 	/* Taints info */
 	if (mod->taints)
 		seq_printf(m, " %s", module_flags(mod, buf));
@@ -3097,8 +3100,12 @@ void print_modules(void)
 	printk(KERN_DEFAULT "Modules linked in:");
 	/* Most callers should already have preempt disabled, but make sure */
 	preempt_disable();
-	list_for_each_entry_rcu(mod, &modules, list)
+	list_for_each_entry_rcu(mod, &modules, list) {
 		printk(" %s%s", mod->name, module_flags(mod, buf));
+#ifdef ARCH_OOPS_MODULE_EXTRA
+		ARCH_OOPS_MODULE_EXTRA(mod);
+#endif
+	}
 	preempt_enable();
 	if (last_unloaded_module[0])
 		printk(" [last unloaded: %s]", last_unloaded_module);
--- a/kernel/sched_clock.c
+++ b/kernel/sched_clock.c
@@ -38,8 +38,7 @@
  */
 unsigned long long __attribute__((weak)) sched_clock(void)
 {
-	return (unsigned long long)(jiffies - INITIAL_JIFFIES)
-					* (NSEC_PER_SEC / HZ);
+	return (get_jiffies_64() - INITIAL_JIFFIES) * (NSEC_PER_SEC / HZ);
 }
 
 static __read_mostly int sched_clock_running;
--- a/lib/Kconfig.debug
+++ b/lib/Kconfig.debug
@@ -690,7 +690,7 @@ config FRAME_POINTER
 	bool "Compile the kernel with frame pointers"
 	depends on DEBUG_KERNEL && \
 		(CRIS || M68K || M68KNOMMU || FRV || UML || \
-		 AVR32 || SUPERH || BLACKFIN || MN10300) || \
+		 AVR32 || SUPERH || BLACKFIN || MN10300 || UBICOM32) || \
 		ARCH_WANT_FRAME_POINTERS
 	default y if (DEBUG_INFO && UML) || ARCH_WANT_FRAME_POINTERS
 	help
--- a/mm/Makefile
+++ b/mm/Makefile
@@ -45,3 +45,5 @@ obj-$(CONFIG_MEMORY_FAILURE) += memory-f
 obj-$(CONFIG_HWPOISON_INJECT) += hwpoison-inject.o
 obj-$(CONFIG_DEBUG_KMEMLEAK) += kmemleak.o
 obj-$(CONFIG_DEBUG_KMEMLEAK_TEST) += kmemleak-test.o
+
+CFLAGS_slab.o := $(PROFILING) -O2
--- a/mm/slab.c
+++ b/mm/slab.c
@@ -4086,6 +4086,68 @@ out:
 
 #ifdef CONFIG_SLABINFO
 
+
+/*
+ * get info on all the memory allocated by slab for this named cache
+ */
+int kmem_cache_block_info(char *name, struct kmem_cache_size_info *data, int max_data)
+{
+	int res = 0;
+	int found = 0;
+	int node;
+	struct kmem_cache *cachep;
+	struct kmem_list3 *l3;
+	struct slab *slabp;
+
+	/* Find the cache in the chain of caches. */
+	mutex_lock(&cache_chain_mutex);
+	list_for_each_entry(cachep, &cache_chain, next) {
+		if (strcmp(cachep->name, name) == 0) {
+			found = 1;
+			break;
+		}
+	}
+	mutex_unlock(&cache_chain_mutex);
+	if (!found) {
+		return 0;
+	}
+	for_each_online_node(node) {
+		l3 = cachep->nodelists[node];
+		if (!l3)
+			continue;
+		if (res >= max_data)
+			break;
+		check_irq_on();
+		spin_lock_irq(&l3->list_lock);
+
+		list_for_each_entry(slabp, &l3->slabs_full, list) {
+			if (res >= max_data)
+				break;
+			data[res].page = ((unsigned int)slabp->s_mem >> PAGE_SHIFT) & 0xffff;
+			data[res].order = cachep->gfporder;
+			res++;
+		}
+		list_for_each_entry(slabp, &l3->slabs_partial, list) {
+			if (res >= max_data)
+				break;
+			data[res].page = ((unsigned int)slabp->s_mem >> PAGE_SHIFT) & 0xffff;
+			data[res].order = cachep->gfporder;
+			res++;
+		}
+		list_for_each_entry(slabp, &l3->slabs_free, list) {
+			if (res >= max_data)
+				break;
+			data[res].page = ((unsigned int)slabp->s_mem >> PAGE_SHIFT) & 0xffff;
+			data[res].order = cachep->gfporder;
+			res++;
+		}
+
+		spin_unlock_irq(&l3->list_lock);
+	}
+
+	return res;
+}
+
 static void print_slabinfo_header(struct seq_file *m)
 {
 	/*
--- a/scripts/mod/file2alias.c
+++ b/scripts/mod/file2alias.c
@@ -783,6 +783,15 @@ void handle_moddevtable(struct module *m
 			+ sym->st_value;
 	}
 
+	/*
+	 * somehow our gcc is not generating st_size correctly and set 0 for some symbols.
+	 * and 0 size will break do_table since it adjust size to (size - id_size)
+	 * this is to make sure st_size fall in range.
+	 */
+	if (sym->st_size == 0 || sym->st_size > info->sechdrs[sym->st_shndx].sh_size) {
+		sym->st_size = info->sechdrs[sym->st_shndx].sh_size;
+	}
+
 	if (sym_is(symname, "__mod_pci_device_table"))
 		do_table(symval, sym->st_size,
 			 sizeof(struct pci_device_id), "pci",
--- a/sound/Kconfig
+++ b/sound/Kconfig
@@ -110,6 +110,8 @@ source "sound/parisc/Kconfig"
 
 source "sound/soc/Kconfig"
 
+source "sound/ubicom32/Kconfig"
+
 endif # SND
 
 menuconfig SOUND_PRIME
--- a/sound/Makefile
+++ b/sound/Makefile
@@ -6,7 +6,7 @@ obj-$(CONFIG_SOUND_PRIME) += sound_firmw
 obj-$(CONFIG_SOUND_PRIME) += oss/
 obj-$(CONFIG_DMASOUND) += oss/
 obj-$(CONFIG_SND) += core/ i2c/ drivers/ isa/ pci/ ppc/ arm/ sh/ synth/ usb/ \
-	sparc/ spi/ parisc/ pcmcia/ mips/ soc/ atmel/
+	sparc/ spi/ parisc/ pcmcia/ mips/ soc/ atmel/ ubicom32/
 obj-$(CONFIG_SND_AOA) += aoa/
 
 # This one must be compilable even if sound is configured out