summaryrefslogtreecommitdiffstats
path: root/target/linux/x86/net5501/config-default
Commit message (Collapse)AuthorAgeFilesLines
* x86: remove support for old kernelsjuhosg2012-05-181-20/+0
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31804 3c298f89-4303-0410-b956-a3cf2f4a3e73
* x86: sync 3.2 configsjuhosg2012-05-161-2/+5
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31750 3c298f89-4303-0410-b956-a3cf2f4a3e73
* linux: move certain disabled symbols to the generic configsjuhosg2012-05-151-7/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * CONFIG_ARCH_DMA_ADDR_T_64BIT * CONFIG_ARCH_HAS_ILOG2_U32 * CONFIG_ARCH_HAS_ILOG2_U64 * CONFIG_ARCH_PHYS_ADDR_T_64BIT * CONFIG_ARCH_SUPPORTS_MSI * CONFIG_GENERIC_CPU_DEVICES * CONFIG_HWMON_DEBUG_CHIP * CONFIG_I2C_PXA_PCI * CONFIG_LEDS_GPIO * CONFIG_MINIX_FS_NATIVE_ENDIAN * CONFIG_MLX4_CORE * CONFIG_POWER_SUPPLY * CONFIG_POWER_SUPPLY_DEBUG * CONFIG_QUOTACTL * CONFIG_SDIO_UART * CONFIG_SENSORS_K10TEMP * CONFIG_SENSORS_SCH56XX_COMMON * CONFIG_SENSORS_VIA_CPUTEMP * CONFIG_SERIO_AMBAKMI * CONFIG_SERIO_I8042 * CONFIG_SERIO_LIBPS2 * CONFIG_SERIO_PCIPS2 * CONFIG_SERIO_RAW * CONFIG_SERIO_SERPORT * CONFIG_SPI_BITBANG * CONFIG_SPI_GPIO git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31737 3c298f89-4303-0410-b956-a3cf2f4a3e73
* config: deprecated symbol CONFIG_LEDS_GPIO_PLATFORMjow2012-02-241-1/+0
| | | | | | | | | | | | CONFIG_LEDS_GPIO_PLATFORM went away a while ago. http://git.kernel.org/?p=linux/kernel/git/stable/linux-stable.git;a=commit;h=2bcc7ed5b83b0a59c6976476e8788675038fb11b Also, most platforms comment out CONFIG_LEDS_GPIO but not x86 for some reason. Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@30708 3c298f89-4303-0410-b956-a3cf2f4a3e73
* [PATCH] net5501: correct net5501 h/w configurationjow2012-02-021-30/+13
| | | | | | | | | | | | | | | | | Bump to version 3.2. Simplify and correct kernel config (based on x86/config-3.2). Designate eth0 as wan interface, and bridge eth1/eth2/eth3. Add heartbeat LED trigger. Use correct CS5535 GPIO driver. Use correct USB drivers (OHCI not UHCI). Add MSR and HW clock support. Add GPIO mask definition. Add correct SATA drivers. Add LED triggers. [Patch from Philipp Prindeville, via http://patchwork.openwrt.org/patch/1802/] git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29994 3c298f89-4303-0410-b956-a3cf2f4a3e73
* x86: turn off CONFIG_X86_GENERIC for geos and net5501nbd2010-11-211-2/+3
| | | | | | | | CONFIG_X86_GENERIC obscures CONFIG_MGEODE_LX, etc. and causes it to use wrong cache-line size. Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@24071 3c298f89-4303-0410-b956-a3cf2f4a3e73
* x86: refresh config, enable pci express supportnbd2010-11-171-0/+1
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@24026 3c298f89-4303-0410-b956-a3cf2f4a3e73
* [x86] resync config-default, enable gpio supportflorian2010-10-301-10/+25
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@23727 3c298f89-4303-0410-b956-a3cf2f4a3e73
* [x86] add net5501 supportflorian2010-04-111-0/+25
This patch brings up the net5501 platform. Note that the x86/ target included support for all x86/ class processors. That's not technically correct. This should be constrained only to the "generic" subtarget. Every x86-class target that isn't generic should be able to select only the optimizations/capabilities applicable to that architectural variant. It's also assumed that all x86 processors have keyboard & mouse ports, ISA, DMI, ACPI... the embedded ones typically don't. Again, moving that to the generic subtarget. Fortunately, this was a fairly benign tweak. The net5501 board includes the following logic: Geode/LX processor CS5535 super-I/O chip PC87360 sensor chip Via Rhine Ethernet controllers Via Sata controllers USB, LEDS, I2C Signed-off-by: Philip Prindeville <philipp_subx@redfish-solutions.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@20794 3c298f89-4303-0410-b956-a3cf2f4a3e73