summaryrefslogtreecommitdiffstats
path: root/target/linux/ramips/files
Commit message (Collapse)AuthorAgeFilesLines
* ramips: Add support for 8devices Carambola dev board.juhosg2012-08-294-0/+49
| | | | | | | | | | | | Add support for 8devices Carambola dev board. The Carambola is a small RT3050-based development board with two ethernet ports, on-board chip antenna, usb and plenty of accessible gpio ports, sold by 8devices. Signed-off-by: Tobias Diedrich <ranma+openwrt@tdiedrich.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33303 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ramips: Rename POC registersjuhosg2012-08-291-31/+31
| | | | | | | | | | | | | | | | | | Rename POC registers. The current code uses POC1-POC3. The datasheet uses: POC1: Port Control 0 POC1: Port Control 1 POC2: Port Control 2 So the first POC1 is a typo that should have been POC0, rename the registers to POC0-POC2 accordingly. Signed-off-by: Tobias Diedrich <ranma+openwrt@tdiedrich.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33302 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ramips: Minor ramips_esw.c cleanupjuhosg2012-08-294-62/+18
| | | | | | | | | | | | Stop handling VLAN setup in the kernel. Removes the obsolete RT305X_ESW_VLAN_CONFIG_BYPASS option I added for WL-351 and add some extra comments. Also removes the en_vlan per-port flag that isn't very useful really, it now is only controlled by the global enable_vlan flag. Signed-off-by: Tobias Diedrich <ranma+openwrt@tdiedrich.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33301 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ramips: Add swconfig support to ramips_esw.cjuhosg2012-08-292-35/+755
| | | | | | | | | | | | | | | | | | | Add swconfig support to ramips_esw.c This patch adds swconfig support for ramips_esw: Tested on both D-LINK DIR-300 B1 and Sitecom WL-351 (external rtl8366rb on internal port 5). I've made sure that in the enable_vlan=0 case it behaves like a dumb switch, so external switches should work fine with vlans and verified this on the WL-351. The current state shown by swconfig is always read directly from HW registers, new settings only show after 'swconfig dev rt305x set apply'. Signed-off-by: Tobias Diedrich <ranma+openwrt@tdiedrich.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33299 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ramips: ramips_esw.c indentation cleanupjuhosg2012-08-291-11/+11
| | | | | | | | | | Minor indentation cleanup. Prepare for the main swconfig patch by cleaning up indentation a bit. Signed-off-by: Tobias Diedrich <ranma+openwrt@tdiedrich.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33298 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ramips: add board alias for the ALL0239-3Gjuhosg2012-08-172-0/+4
| | | | | | | | | | | | | | Generate image for the ALL0239-3G which can be flashed through the chipset-vendor SDK based firmware's web-interface and bootloader. The bootloader seems to ignore uImage checksum errors, but does complain about them once the 0xDEADC0DE was replaced by an actual JFFS2 page. I'm working on implementing fixtrx for uImage in the mtd package to solve this. Signed-off-by: Daniel Golle <dgolle@allnet.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33206 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ramips: add support for D-Link DIR-615 H1juhosg2012-08-174-1/+120
| | | | | | | | | | | | rt2x00 still needs some patching as the radio doesn't come to life. Installation via webflash. [juhosg: fix whitespace issues, remove rt305x_register_usb from machine setup because the board has no USB port] Signed-off-by: Mikko Hissa <mikko.hissa@uta.fi> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33205 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ramips: rename rt3352 usb platform devicesjuhosg2012-08-121-2/+2
| | | | | | | | | In order to get OHCI/EHCI working on the Rt3352, the platform device must be named so rt3883-?hci will recognize it. Signed-off-by: Daniel Golle <dgolle@allnet.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33145 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ramips: watchdog: use maximum possible timeout by defaultjuhosg2012-08-121-6/+6
| | | | | | | | | | | | | As the userspace has no means to determine the maximum possible timeout, use that as the default and let the userspace lower it when necessary. As the result the usual OpenWrt install (with busybox's watchdog trying to set the timeout to 60s on start) is using a 33s timeout on an RT3052 clocked at 384MHz instead of the current 20s default. Signed-off-by: Paul Fertser <fercerpav@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33144 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ramips: add D-Link DIR-620 A1 supportjuhosg2012-08-122-3/+52
| | | | | | | | | | | | Full functionality runtime tested, installation via OEM web-interface requires a follow-up patch. Thanks go to Sergey Vasilyugin for his patch that pointed me at the missing bits (including the antiparallel wps led). Signed-off-by: Paul Fertser <fercerpav@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33142 3c298f89-4303-0410-b956-a3cf2f4a3e73
* [ramips] DWC otg usb: compilation fixes and trivial bugfix in slave modeblogic2012-07-245-5/+45
| | | | | | Signed-of-by: Nikolai Zhubr <n-a-zhubr@yandex.ru> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32823 3c298f89-4303-0410-b956-a3cf2f4a3e73
* [ramips] D-Link DAP-1350 initial supportblogic2012-07-244-0/+101
| | | | | | | | | The initial support for the D-Link DAP-1350. USB related functionality is not tested. Signed-off-by: Yoichi Shinoda <shinoda@jaist.ac.jp> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32821 3c298f89-4303-0410-b956-a3cf2f4a3e73
* [ramips] enable OHCI/EHCI glue on Rt305x, so it is available for Rt3352F.blogic2012-07-241-0/+2
| | | | | | | | Hope that this works, didn't have a chance to actually test it... Signed-off-by: Daniel Golle <dgolle@allnet.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32815 3c298f89-4303-0410-b956-a3cf2f4a3e73
* [ramips] add support for Allnet ALL5002 to kernelblogic2012-07-244-0/+70
| | | | | | | | support ALL5002 in ramips/rt305x branch of the kernel. Signed-off-by: Daniel Golle <dgolle@allnet.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32813 3c298f89-4303-0410-b956-a3cf2f4a3e73
* [ramips] uart_clk on Rt3352F is always 40MHzblogic2012-07-241-1/+1
| | | | | | | | | Currently, sys_clk/10 is used which is just wrong. cpu_clk/10 would work for systems with 400MHz CPU clock. Signed-off-by: Daniel Golle <dgolle@allnet.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32812 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ramips: rt305x: add support for Edimax 3G-6200Njuhosg2012-07-124-0/+93
| | | | | | | | Support for Edimax 3G-6200N router with USB. Signed-off-by: Lukasz Golebiowski <lgolebio@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32682 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ramips: rt305x: add support for the Petatel PSR-680W Wireless CDMA Routerjuhosg2012-06-194-0/+80
| | | | | | | | | | This patch adds support for the Korean made Petatel PSR-680W Wireless CDMA Router. The platform is based on Ralink RT3052. http://wiki.openwrt.org/toh/petatel/psr-680w Signed-off-by: Dmitry Shmygov <shmygov at rambler.ru> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32450 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ramips: WAN LED for D-Link DIR-300-B1juhosg2012-05-291-0/+14
| | | | | | | | | | | | | | | | | | Add led devices for D-Link DIR-300-B1 WAN LED. Note that the GPIO state is also ANDed with the esw switch port 4 LED state, which is why I've set the amber LED to default-on. Closes: https://dev.openwrt.org/ticket/11326 Signed-off-by: Tobias Diedrich <ranma+openwrt@tdiedrich.de> [ juhosg: - fix comment style in mach-dir-300-revb.c, - remove the PPP specific LED setup, not everyone uses a PPP connection on the WAN interface] git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31989 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ramips: rt3883: add device registration code for the SPI controllerjuhosg2012-05-272-0/+26
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31922 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ramips: rt3883: fix GPIO reservation for the SPI pinsjuhosg2012-05-271-1/+1
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31920 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ramips: rt305x: remove superfluous controller_data assignmentjuhosg2012-05-271-1/+0
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31919 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ramips: Add byte queue limits support to net/ethernet/ramips_main.cjuhosg2012-05-231-0/+8
| | | | | | | | | | | | | | Add byte queue limits support to net/ethernet/ramips_main.c "Byte queue limits are a mechanism to limit the size of the transmit hardware queue on a NIC by number of bytes. The goal of these byte limits is too reduce latency (HOL blocking) caused by excessive queuing in hardware (aka buffer bloat) without sacrificing throughput." Signed-off-by: Tobias Diedrich <ranma+openwrt@tdiedrich.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31844 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ramips: W306R V2.0 - GPIO and Network fixesjuhosg2012-05-021-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | Fixed: GPIO typos and confirmed GPIO_BUTTON_RESET Fixed: Lan & Wan reversed: swaped "eth0.2" with "eth0.1" by removing a line(default is correct), and reversed the Lan/wan layout LLLLW to WLLLL. Added: image/Makefile now builds -factory.bin files. I am unsure of the accepted way to change the makefile but the name of the image needs to be 'linkn Kernel Image' in order to be accepted by the OEM firmware. Known issue: eth0 (internal switch i think has mac address: 00:11:22:33:44:55 but i think it should be same as the lan). Known issue: Pressing the reset button has no noticable effect, i would expect the router to boot failsafe if being pressed on boot, reboot if short press and reset all to default if long press. [juhosg: remove mtdlayout_W306R and use mtdlayout_4M instead] Signed-off-by: David Pearce <david_18051985@hotmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31557 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ramips: rt305x: add support for the UR-336UN boardjuhosg2012-04-234-0/+99
| | | | | | Patch-by: Lebedev Dmitry <lebedev@trendnet.ru> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31451 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ramips: rt305x: add support for the Asus WL-330N3G boardjuhosg2012-04-234-0/+107
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the ASUS WL-330N3G Comparing to the WL-330N, It have 32MB ram, usb support and a bicolor led. The bi-color led is driven by 2 gpio. I don't know how to handle this, so I simply made 2 leds : one red, one blue. But the red light takes precedence over the blue one according to the chart below. r = led is red b = led is blue 0 = led is off xy= x->r for red, b for blue led, y->value of brightness in /sys/class/leds/x/brughtness initial state action led gpio state r0 b0 r0->r1 r r0 b0 r0 b0 b0->b1 b r0 b1 r1 b0 r1->r0 0 r0 b0 r1 b0 b0->b1 r r1 *b1* r1 b1 r1->r0 b r0 b1 r1 b1 b1->b0 r r1 b0 r0 b1 r0->r1 r r1 *b1* r0 b1 b1->b0 0 r0 r0 Signed-off-by: Frédéric Leroy <fredo@starox.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31450 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ramips: rt305x: add OHCI/EHCI registration code for RT3352juhosg2012-04-212-5/+161
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31402 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ramips: rt305x: fix CPU clock detection on RT3352juhosg2012-04-212-12/+36
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31401 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ramips: rt305x: use different memory size setup for RT3352juhosg2012-04-212-2/+13
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31400 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ramips: rt305x: add initial support for Tenda W306R V2.0juhosg2012-04-214-0/+79
| | | | | | | | | | More device info at: http://wiki.openwrt.org/toh/tenda/w306r Signed-off-by: David Pearce <David_18051985@hotmail.com.au> [juhosg: fix checkpatch errors, remove kmod-phy and luci-ssl packages from the profile, change broken GPIO number] git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31396 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ramips: add support for the ARC FreeStation5 board, also fix WCR-150GN ↵jow2012-03-294-0/+39
| | | | | | network setup while we're at it - thanks Pau Escrich <p4u@dabax.net> for the implementation git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31144 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ramips: rt305x: build image for the DIR-615 rev D boardsjuhosg2012-03-272-0/+4
| | | | | | Patch from #10105. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31101 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ramips: rt305x: add add support for the Asus WL-330N boardjuhosg2012-03-274-0/+101
| | | | | | | | | [juhosg: reorder several lines in order to keep things sorted alphabetically] Signed-off-by: Frédéric Leroy <fredo@starox.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31100 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ramips: add RT3350 detectionjuhosg2012-03-123-0/+12
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@30900 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ramips: rt305x: rewrite SoC detectionjuhosg2012-03-113-5/+60
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@30890 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ramips: rt305x: rename SYSTEM_CONFIG_* defines to RT305X_SYSCFG_*juhosg2012-03-113-14/+14
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@30889 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ramips: replace RALINK_SOC_* macros with global variablesjuhosg2012-03-1110-64/+30
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@30888 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ramips: introduce ramips_soc_prom_init and move SoC detection into thatjuhosg2012-03-1111-21/+18
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@30887 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ramips: allow to use DSP ASE on RT3xxxjuhosg2012-03-112-2/+2
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@30879 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ramips: add support for unbranded XDX-RN502J boardjuhosg2012-03-044-0/+86
| | | | | | | | | | | | | | | | | | | | | | | This patch adds support for routers using a PCB marked XDX-RN502J V2.0, such as some unbranded routers like this: http://www.mediafire.com/?8acv87h6snn9fj6 http://www.mediafire.com/?do7xonw7scor4kn http://www.mediafire.com/?1ad49zvx3e7jyix http://www.mediafire.com/?i46cqiq66maa197 http://www.aliexpress.com/product-fm/516397994-Free-Shipping-300M-3G-WAN-Wireless-N-WiFi-USB-AP-Router-2-Antennas-wholesalers.html some reports also state the Aceex 22Y uses the same board. more information can be found in the following openwrt forum post https://forum.openwrt.org/viewtopic.php?id=34878 [juhosg: fix checkpatch warnings, use the GENERIC_4M template] Signed-off-by: bruno schwander <bruno@tinkerbox.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@30809 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ramips: board support for Asus RT-N10+juhosg2012-03-044-0/+81
| | | | | | | | | [juhosg: fix indentation in platform scripts, and remove debug messages from 06_set_iface_mac] Signed-off-by: Patrick van Staveren <trick@vanstaveren.us> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@30808 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ramips: don't read RAMIPS_RX_CALC_IDX0 register in the loopjuhosg2012-02-261-1/+3
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@30733 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ramips: raeth: add rx_info structurejuhosg2012-02-262-24/+57
| | | | | | | | | | | | | This helps to reduce code size on RX path: add/remove: 0/0 grow/shrink: 3/1 up/down: 68/-56 (12) function old new delta ramips_eth_open 1104 1144 +40 ramips_ring_free 212 232 +20 ramips_eth_stop 400 408 +8 ramips_eth_rx_hw 648 592 -56 git-svn-id: svn://svn.openwrt.org/openwrt/trunk@30732 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ramips: raeth: add tx_info structurejuhosg2012-02-262-19/+55
| | | | | | | | | | | | | | This helps to reduce code size on TX path: add/remove: 0/0 grow/shrink: 1/4 up/down: 56/-92 (-36) function old new delta ramips_eth_open 1048 1104 +56 ramips_eth_tx_housekeeping 156 148 -8 ramips_ring_free 224 212 -12 ramips_eth_stop 420 400 -20 ramips_eth_hard_start_xmit 480 428 -52 git-svn-id: svn://svn.openwrt.org/openwrt/trunk@30731 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ramips: raeth: don't process disabled interruptsjuhosg2012-02-251-5/+11
| | | | | | Also rename the 'fe_int' variable. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@30713 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ramips: raeth: show interrupt statistics in debugfsjuhosg2012-02-223-0/+105
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@30681 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ramips: raeth: add debugfs supportjuhosg2012-02-225-1/+91
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@30680 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ramips: raeth: rename main source filejuhosg2012-02-222-0/+2
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@30679 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ramips: raeth: add missing Kconfig and Makefilejuhosg2012-02-212-0/+18
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@30671 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ramips: move the ethernet driver into a separate directoryjuhosg2012-02-213-0/+0
| | | | | | Also clean up the Kconfig symbols. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@30670 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ramips: rename the spi driverjuhosg2012-02-211-0/+0
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@30669 3c298f89-4303-0410-b956-a3cf2f4a3e73
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-19 01:04:06 +0000