diff options
Diffstat (limited to 'target/linux/realtek/files/drivers/net/wireless/rtl8192e/Hal8821APwrSeq.h')
| -rw-r--r-- | target/linux/realtek/files/drivers/net/wireless/rtl8192e/Hal8821APwrSeq.h | 162 |
1 files changed, 162 insertions, 0 deletions
diff --git a/target/linux/realtek/files/drivers/net/wireless/rtl8192e/Hal8821APwrSeq.h b/target/linux/realtek/files/drivers/net/wireless/rtl8192e/Hal8821APwrSeq.h new file mode 100644 index 000000000..a4433cc0e --- /dev/null +++ b/target/linux/realtek/files/drivers/net/wireless/rtl8192e/Hal8821APwrSeq.h @@ -0,0 +1,162 @@ +//#ifndef REALTEK_POWER_SEQUENCE_8821
+//#define REALTEK_POWER_SEQUENCE_8821
+
+#ifdef CONFIG_RTL_92E_SUPPORT
+
+#ifdef CONFIG_WLAN_HAL
+#include "WlanHAL/RTL88XX/Hal88XXPwrSeqCmd.h"
+
+#endif
+
+
+#ifdef BIT
+#undef BIT
+#endif
+#define BIT(x) (1 << (x))
+
+/*
+ Check document WM-20110607-Paul-RTL8821A_Power_Architecture-R02.vsd
+ There are 6 HW Power States:
+ 0: POFF--Power Off
+ 1: PDN--Power Down
+ 2: CARDEMU--Card Emulation
+ 3: ACT--Active Mode
+ 4: LPS--Low Power State
+ 5: SUS--Suspend
+
+ The transision from different states are defined below
+ TRANS_CARDEMU_TO_ACT
+ TRANS_ACT_TO_CARDEMU
+ TRANS_CARDEMU_TO_SUS
+ TRANS_SUS_TO_CARDEMU
+ TRANS_CARDEMU_TO_PDN
+ TRANS_ACT_TO_LPS
+ TRANS_LPS_TO_ACT
+
+ TRANS_END
+*/
+#define RTL8821A_TRANS_CARDEMU_TO_ACT_STEPS 15
+#define RTL8821A_TRANS_ACT_TO_CARDEMU_STEPS 15
+#define RTL8821A_TRANS_CARDEMU_TO_SUS_STEPS 15
+#define RTL8821A_TRANS_SUS_TO_CARDEMU_STEPS 15
+#define RTL8821A_TRANS_CARDEMU_TO_PDN_STEPS 15
+#define RTL8821A_TRANS_PDN_TO_CARDEMU_STEPS 15
+#define RTL8821A_TRANS_ACT_TO_LPS_STEPS 15
+#define RTL8821A_TRANS_LPS_TO_ACT_STEPS 15
+#define RTL8821A_TRANS_END_STEPS 1
+
+
+#define RTL8821A_TRANS_CARDEMU_TO_ACT \
+ /* format */ \
+ /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/ \
+ {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT(2), 0},/* disable SW LPS 0x04[10]=0*/ \
+ {0x0006, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_POLLING, BIT(1), BIT(1)},/* wait till 0x04[17] = 1 power ready*/ \
+ {0x0006, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT(0), BIT(0)},/* release WLON reset 0x04[16]=1*/ \
+ {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT(7), 0},/* disable HWPDN 0x04[15]=0*/ \
+ {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, (BIT(4)|BIT(3)), 0},/* disable WL suspend*/ \
+ {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT(0), BIT(0)},/* polling until return 0*/ \
+ {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_POLLING, BIT(0), 0},/**/ \
+
+
+#define RTL8821A_TRANS_ACT_TO_CARDEMU \
+ /* format */ \
+ /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/ \
+ {0x001F, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0},/*0x1F[7:0] = 0 turn off RF*/ \
+ {0x004E, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT(7), 0},/*0x4C[23] = 0x4E[7] = 0, switch DPDT_SEL_P output from register 0x65[2] */\
+ {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT(1), BIT(1)}, /*0x04[9] = 1 turn off MAC by HW state machine*/ \
+ {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_POLLING, BIT(1), 0}, /*wait till 0x04[9] = 0 polling until return 0 to disable*/ \
+
+#define RTL8821A_TRANS_CARDEMU_TO_SUS \
+ /* format */ \
+ /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/ \
+ {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT(4)|BIT(3), (BIT(4)|BIT(3))}, /*0x04[12:11] = 2b'11 enable WL suspend for PCIe*/ \
+ {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT(3)|BIT(4), BIT(3)}, /*0x04[12:11] = 2b'01 enable WL suspend*/ \
+ {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT(3)|BIT(4), BIT(3)|BIT(4)}, /*0x04[12:11] = 2b'11 enable WL suspend for PCIe*/ \
+ {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_SDIO,PWR_CMD_WRITE, BIT(0), BIT(0)}, /*Set SDIO suspend local register*/ \
+ {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_SDIO,PWR_CMD_POLLING, BIT(1), 0}, /*wait power state to suspend*/
+
+#define RTL8821A_TRANS_SUS_TO_CARDEMU \
+ /* format */ \
+ /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/ \
+ {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_SDIO,PWR_CMD_WRITE, BIT(0), 0}, /*Set SDIO suspend local register*/ \
+ {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_SDIO,PWR_CMD_POLLING, BIT(1), BIT(1)}, /*wait power state to suspend*/\
+ {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT(3)|BIT(4), 0}, /*0x04[12:11] = 2b'01enable WL suspend*/
+
+#define RTL8821A_TRANS_CARDEMU_TO_CARDDIS \
+ /* format */ \
+ /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/ \
+ {0x0007, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0x20}, /*0x07=0x20 , SOP option to disable BG/MB*/ \
+ {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT(3)|BIT(4), BIT(3)}, /*0x04[12:11] = 2b'01 enable WL suspend*/ \
+ {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT(2), BIT(2)}, /*0x04[10] = 1, enable SW LPS*/ \
+ {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_SDIO,PWR_CMD_WRITE, BIT(0), BIT(0)}, /*Set SDIO suspend local register*/ \
+ {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_SDIO,PWR_CMD_POLLING, BIT(1), 0}, /*wait power state to suspend*/
+
+#define RTL8821A_TRANS_CARDDIS_TO_CARDEMU \
+ /* format */ \
+ /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/ \
+ {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_SDIO,PWR_CMD_WRITE, BIT(0), 0}, /*Set SDIO suspend local register*/ \
+ {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_SDIO,PWR_CMD_POLLING, BIT(1), BIT(1)}, /*wait power state to suspend*/\
+ {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT(3)|BIT(4), 0}, /*0x04[12:11] = 2b'01enable WL suspend*/\
+ {0x0301, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0},/*PCIe DMA start*/
+
+
+#define RTL8821A_TRANS_CARDEMU_TO_PDN \
+ /* format */ \
+ /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/ \
+ {0x0006, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT(0), 0},/* 0x04[16] = 0*/\
+ {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT(7), BIT(7)},/* 0x04[15] = 1*/
+
+#define RTL8821A_TRANS_PDN_TO_CARDEMU \
+ /* format */ \
+ /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/ \
+ {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT(7), 0},/* 0x04[15] = 0*/
+
+#define RTL8821A_TRANS_ACT_TO_LPS \
+ /* format */ \
+ /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/ \
+ {0x0301, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0xFF},/*PCIe DMA stop*/ \
+ {0x0522, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0xFF},/*Tx Pause*/ \
+ {0x05F8, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_POLLING, 0xFF, 0},/*Should be zero if no packet is transmitting*/ \
+ {0x05F9, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_POLLING, 0xFF, 0},/*Should be zero if no packet is transmitting*/ \
+ {0x05FA, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_POLLING, 0xFF, 0},/*Should be zero if no packet is transmitting*/ \
+ {0x05FB, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_POLLING, 0xFF, 0},/*Should be zero if no packet is transmitting*/ \
+ {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT(0), 0},/*CCK and OFDM are disabled,and clock are gated*/ \
+ {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_DELAY, 0, PWRSEQ_DELAY_US},/*Delay 1us*/ \
+ {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT(1), 0},/*Whole BB is reset*/ \
+ {0x0100, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0x03},/*Reset MAC TRX*/ \
+ {0x0101, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT(1), 0},/*check if removed later*/ \
+ {0x0553, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT(5), BIT(5)},/*Respond TxOK to scheduler*/ \
+
+
+#define RTL8821A_TRANS_LPS_TO_ACT \
+ /* format */ \
+ /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/ \
+ {0x0080, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_SDIO,PWR_CMD_WRITE, 0xFF, 0x84}, /*SDIO RPWM*/\
+ {0xFE58, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0x84}, /*USB RPWM*/\
+ {0x0361, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0x84}, /*PCIe RPWM*/\
+ {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_DELAY, 0, PWRSEQ_DELAY_MS}, /*Delay*/\
+ {0x0008, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT(4), 0}, /*. 0x08[4] = 0 switch TSF to 40M*/\
+ {0x0109, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_POLLING, BIT(7), 0}, /*Polling 0x109[7]=0 TSF in 40M*/\
+ {0x0029, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT(6)|BIT(7), 0}, /*. 0x29[7:6] = 2b'00 enable BB clock*/\
+ {0x0101, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT(1), BIT(1)}, /*. 0x101[1] = 1*/\
+ {0x0100, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0xFF}, /*. 0x100[7:0] = 0xFF enable WMAC TRX*/\
+ {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT(1)|BIT(0), BIT(1)|BIT(0)}, /*. 0x02[1:0] = 2b'11 enable BB macro*/\
+ {0x0522, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0}, /*. 0x522 = 0*/
+
+#define RTL8821A_TRANS_END \
+ /* format */ \
+ /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/ \
+ {0xFFFF, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,0,PWR_CMD_END, 0, 0}, //
+
+
+extern WLAN_PWR_CFG rtl8821A_power_on_flow[RTL8821A_TRANS_CARDEMU_TO_ACT_STEPS+RTL8821A_TRANS_END_STEPS];
+extern WLAN_PWR_CFG rtl8821A_radio_off_flow[RTL8821A_TRANS_ACT_TO_CARDEMU_STEPS+RTL8821A_TRANS_END_STEPS];
+extern WLAN_PWR_CFG rtl8821A_card_disable_flow[RTL8821A_TRANS_ACT_TO_CARDEMU_STEPS+RTL8821A_TRANS_CARDEMU_TO_PDN_STEPS+RTL8821A_TRANS_END_STEPS];
+extern WLAN_PWR_CFG rtl8821A_card_enable_flow[RTL8821A_TRANS_ACT_TO_CARDEMU_STEPS+RTL8821A_TRANS_CARDEMU_TO_PDN_STEPS+RTL8821A_TRANS_END_STEPS];
+extern WLAN_PWR_CFG rtl8821A_suspend_flow[RTL8821A_TRANS_ACT_TO_CARDEMU_STEPS+RTL8821A_TRANS_CARDEMU_TO_SUS_STEPS+RTL8821A_TRANS_END_STEPS];
+extern WLAN_PWR_CFG rtl8821A_resume_flow[RTL8821A_TRANS_ACT_TO_CARDEMU_STEPS+RTL8821A_TRANS_CARDEMU_TO_SUS_STEPS+RTL8821A_TRANS_END_STEPS];
+extern WLAN_PWR_CFG rtl8821A_hwpdn_flow[RTL8821A_TRANS_ACT_TO_CARDEMU_STEPS+RTL8821A_TRANS_CARDEMU_TO_PDN_STEPS+RTL8821A_TRANS_END_STEPS];
+extern WLAN_PWR_CFG rtl8821A_enter_lps_flow[RTL8821A_TRANS_ACT_TO_LPS_STEPS+RTL8821A_TRANS_END_STEPS];
+extern WLAN_PWR_CFG rtl8821A_leave_lps_flow[RTL8821A_TRANS_LPS_TO_ACT_STEPS+RTL8821A_TRANS_END_STEPS];
+
+#endif
|