summaryrefslogtreecommitdiffstats
path: root/target/linux/ixp4xx/patches-2.6.25/030-ixp4xx_fsg_board_support.patch
diff options
context:
space:
mode:
Diffstat (limited to 'target/linux/ixp4xx/patches-2.6.25/030-ixp4xx_fsg_board_support.patch')
-rw-r--r--target/linux/ixp4xx/patches-2.6.25/030-ixp4xx_fsg_board_support.patch559
1 files changed, 0 insertions, 559 deletions
diff --git a/target/linux/ixp4xx/patches-2.6.25/030-ixp4xx_fsg_board_support.patch b/target/linux/ixp4xx/patches-2.6.25/030-ixp4xx_fsg_board_support.patch
deleted file mode 100644
index 8fb7280e0..000000000
--- a/target/linux/ixp4xx/patches-2.6.25/030-ixp4xx_fsg_board_support.patch
+++ /dev/null
@@ -1,559 +0,0 @@
-From: Rod Whitby <rod@whitby.id.au>
-Subject: [PATCH] ixp4xx: Add support for the Freecom FSG-3 board (Patch #4874)
-
-The Freecom-FSG3 is a small network-attached-storage device with the
-following feature set:
-
-* Intel IXP422
-* 4MB Flash (ixp4xx flash driver)
-* 64MB RAM
-* 4 USB 2.0 host ports (ehci and ohci drivers)
-* 1 WAN (eth1) and 3 LAN (eth0) ethernet ports
- * Supported by the open source ixp4xx ethernet driver
-* Via VT6421 disk controller (libata and sata-via drivers)
- * Internal hard disk (PATA supported, SATA not yet supported)
- * External SATA port (not yet supported)
-* ISL1208 RTC chip
-* Winbond 83782 temp sensor and fan controller
-* MiniPCI slot
-
-The ixp4xx_defconfig is also updated to support this device (the
-leds-fsg driver is to be submitted separately via the leds tree after
-this initial support is merged, as it depends on header gpio defines).
-
-Signed-off-by: Rod Whitby <rod@whitby.id.au>
-
-PATCH FOLLOWS
-KernelVersion: v2.6.25-rc6-74-g264e3e8
----
-
-Updated to correct all issues found by RMK.
-
-The front power button calls ctrl_alt_del() and the rear reset button
-now calls machine_restart() directly.
-
- arch/arm/configs/ixp4xx_defconfig | 9 +-
- arch/arm/mach-ixp4xx/Kconfig | 9 +
- arch/arm/mach-ixp4xx/Makefile | 2 +
- arch/arm/mach-ixp4xx/fsg-pci.c | 71 ++++++++
- arch/arm/mach-ixp4xx/fsg-setup.c | 276 ++++++++++++++++++++++++++++++++
- include/asm-arm/arch-ixp4xx/fsg.h | 50 ++++++
- include/asm-arm/arch-ixp4xx/hardware.h | 1 +
- include/asm-arm/arch-ixp4xx/irqs.h | 7 +
- 8 files changed, 421 insertions(+), 4 deletions(-)
- create mode 100644 arch/arm/mach-ixp4xx/fsg-pci.c
- create mode 100644 arch/arm/mach-ixp4xx/fsg-setup.c
- create mode 100644 include/asm-arm/arch-ixp4xx/fsg.h
-
---- a/arch/arm/configs/ixp4xx_defconfig
-+++ b/arch/arm/configs/ixp4xx_defconfig
-@@ -165,6 +165,7 @@
- CONFIG_MACH_NAS100D=y
- CONFIG_MACH_DSMG600=y
- CONFIG_ARCH_IXDP4XX=y
-+CONFIG_MACH_FSG=y
- CONFIG_CPU_IXP46X=y
- CONFIG_CPU_IXP43X=y
- CONFIG_MACH_GTWX5715=y
-@@ -770,7 +771,7 @@
- # CONFIG_SATA_SIL24 is not set
- # CONFIG_SATA_SIS is not set
- # CONFIG_SATA_ULI is not set
--# CONFIG_SATA_VIA is not set
-+CONFIG_SATA_VIA=y
- # CONFIG_SATA_VITESSE is not set
- # CONFIG_SATA_INIC162X is not set
- # CONFIG_PATA_ALI is not set
-@@ -1143,7 +1144,7 @@
- # CONFIG_SENSORS_VIA686A is not set
- # CONFIG_SENSORS_VT1211 is not set
- # CONFIG_SENSORS_VT8231 is not set
--# CONFIG_SENSORS_W83781D is not set
-+CONFIG_SENSORS_W83781D=y
- # CONFIG_SENSORS_W83791D is not set
- # CONFIG_SENSORS_W83792D is not set
- # CONFIG_SENSORS_W83793 is not set
-@@ -1334,8 +1335,8 @@
- #
- # LED drivers
- #
--# CONFIG_LEDS_IXP4XX is not set
- CONFIG_LEDS_GPIO=y
-+CONFIG_LEDS_FSG=y
-
- #
- # LED Triggers
-@@ -1367,7 +1368,7 @@
- # CONFIG_RTC_DRV_DS1672 is not set
- # CONFIG_RTC_DRV_MAX6900 is not set
- # CONFIG_RTC_DRV_RS5C372 is not set
--# CONFIG_RTC_DRV_ISL1208 is not set
-+CONFIG_RTC_DRV_ISL1208=y
- CONFIG_RTC_DRV_X1205=y
- CONFIG_RTC_DRV_PCF8563=y
- # CONFIG_RTC_DRV_PCF8583 is not set
---- a/arch/arm/mach-ixp4xx/Kconfig
-+++ b/arch/arm/mach-ixp4xx/Kconfig
-@@ -125,6 +125,15 @@
- depends on ARCH_IXDP425 || MACH_IXDP465 || MACH_KIXRP435
- default y
-
-+config MACH_FSG
-+ bool
-+ prompt "Freecom FSG-3"
-+ select PCI
-+ help
-+ Say 'Y' here if you want your kernel to support Freecom's
-+ FSG-3 device. For more information on this platform,
-+ see http://www.nslu2-linux.org/wiki/FSG3/HomePage
-+
- #
- # Certain registers and IRQs are only enabled if supporting IXP465 CPUs
- #
---- a/arch/arm/mach-ixp4xx/Makefile
-+++ b/arch/arm/mach-ixp4xx/Makefile
-@@ -15,6 +15,7 @@
- obj-pci-$(CONFIG_MACH_DSMG600) += dsmg600-pci.o
- obj-pci-$(CONFIG_MACH_GATEWAY7001) += gateway7001-pci.o
- obj-pci-$(CONFIG_MACH_WG302V2) += wg302v2-pci.o
-+obj-pci-$(CONFIG_MACH_FSG) += fsg-pci.o
-
- obj-y += common.o
-
-@@ -28,6 +29,7 @@
- obj-$(CONFIG_MACH_DSMG600) += dsmg600-setup.o
- obj-$(CONFIG_MACH_GATEWAY7001) += gateway7001-setup.o
- obj-$(CONFIG_MACH_WG302V2) += wg302v2-setup.o
-+obj-$(CONFIG_MACH_FSG) += fsg-setup.o
-
- obj-$(CONFIG_PCI) += $(obj-pci-$(CONFIG_PCI)) common-pci.o
- obj-$(CONFIG_IXP4XX_QMGR) += ixp4xx_qmgr.o
---- /dev/null
-+++ b/arch/arm/mach-ixp4xx/fsg-pci.c
-@@ -0,0 +1,71 @@
-+/*
-+ * arch/arch/mach-ixp4xx/fsg-pci.c
-+ *
-+ * FSG board-level PCI initialization
-+ *
-+ * Author: Rod Whitby <rod@whitby.id.au>
-+ * Maintainer: http://www.nslu2-linux.org/
-+ *
-+ * based on ixdp425-pci.c:
-+ * Copyright (C) 2002 Intel Corporation.
-+ * Copyright (C) 2003-2004 MontaVista Software, Inc.
-+ *
-+ * This program is free software; you can redistribute it and/or modify
-+ * it under the terms of the GNU General Public License version 2 as
-+ * published by the Free Software Foundation.
-+ *
-+ */
-+
-+#include <linux/pci.h>
-+#include <linux/init.h>
-+#include <linux/irq.h>
-+
-+#include <asm/mach/pci.h>
-+#include <asm/mach-types.h>
-+
-+void __init fsg_pci_preinit(void)
-+{
-+ set_irq_type(IRQ_FSG_PCI_INTA, IRQT_LOW);
-+ set_irq_type(IRQ_FSG_PCI_INTB, IRQT_LOW);
-+ set_irq_type(IRQ_FSG_PCI_INTC, IRQT_LOW);
-+
-+ ixp4xx_pci_preinit();
-+}
-+
-+static int __init fsg_map_irq(struct pci_dev *dev, u8 slot, u8 pin)
-+{
-+ static int pci_irq_table[FSG_PCI_IRQ_LINES] = {
-+ IRQ_FSG_PCI_INTC,
-+ IRQ_FSG_PCI_INTB,
-+ IRQ_FSG_PCI_INTA,
-+ };
-+
-+ int irq = -1;
-+ slot = slot - 11;
-+
-+ if (slot >= 1 && slot <= FSG_PCI_MAX_DEV &&
-+ pin >= 1 && pin <= FSG_PCI_IRQ_LINES)
-+ irq = pci_irq_table[(slot - 1)];
-+ printk(KERN_INFO "%s: Mapped slot %d pin %d to IRQ %d\n",
-+ __func__, slot, pin, irq);
-+
-+ return irq;
-+}
-+
-+struct hw_pci fsg_pci __initdata = {
-+ .nr_controllers = 1,
-+ .preinit = fsg_pci_preinit,
-+ .swizzle = pci_std_swizzle,
-+ .setup = ixp4xx_setup,
-+ .scan = ixp4xx_scan_bus,
-+ .map_irq = fsg_map_irq,
-+};
-+
-+int __init fsg_pci_init(void)
-+{
-+ if (machine_is_fsg())
-+ pci_common_init(&fsg_pci);
-+ return 0;
-+}
-+
-+subsys_initcall(fsg_pci_init);
---- /dev/null
-+++ b/arch/arm/mach-ixp4xx/fsg-setup.c
-@@ -0,0 +1,276 @@
-+/*
-+ * arch/arm/mach-ixp4xx/fsg-setup.c
-+ *
-+ * FSG board-setup
-+ *
-+ * Copyright (C) 2008 Rod Whitby <rod@whitby.id.au>
-+ *
-+ * based on ixdp425-setup.c:
-+ * Copyright (C) 2003-2004 MontaVista Software, Inc.
-+ * based on nslu2-power.c
-+ * Copyright (C) 2005 Tower Technologies
-+ *
-+ * Author: Rod Whitby <rod@whitby.id.au>
-+ * Maintainers: http://www.nslu2-linux.org/
-+ *
-+ */
-+
-+#include <linux/if_ether.h>
-+#include <linux/irq.h>
-+#include <linux/serial.h>
-+#include <linux/serial_8250.h>
-+#include <linux/leds.h>
-+#include <linux/reboot.h>
-+#include <linux/i2c.h>
-+#include <linux/i2c-gpio.h>
-+
-+#include <asm/mach-types.h>
-+#include <asm/mach/arch.h>
-+#include <asm/mach/flash.h>
-+#include <asm/io.h>
-+#include <asm/gpio.h>
-+
-+static struct flash_platform_data fsg_flash_data = {
-+ .map_name = "cfi_probe",
-+ .width = 2,
-+};
-+
-+static struct resource fsg_flash_resource = {
-+ .flags = IORESOURCE_MEM,
-+};
-+
-+static struct platform_device fsg_flash = {
-+ .name = "IXP4XX-Flash",
-+ .id = 0,
-+ .dev = {
-+ .platform_data = &fsg_flash_data,
-+ },
-+ .num_resources = 1,
-+ .resource = &fsg_flash_resource,
-+};
-+
-+static struct i2c_gpio_platform_data fsg_i2c_gpio_data = {
-+ .sda_pin = FSG_SDA_PIN,
-+ .scl_pin = FSG_SCL_PIN,
-+};
-+
-+static struct platform_device fsg_i2c_gpio = {
-+ .name = "i2c-gpio",
-+ .id = 0,
-+ .dev = {
-+ .platform_data = &fsg_i2c_gpio_data,
-+ },
-+};
-+
-+static struct i2c_board_info __initdata fsg_i2c_board_info [] = {
-+ {
-+ I2C_BOARD_INFO("rtc-isl1208", 0x6f),
-+ },
-+};
-+
-+static struct resource fsg_uart_resources[] = {
-+ {
-+ .start = IXP4XX_UART1_BASE_PHYS,
-+ .end = IXP4XX_UART1_BASE_PHYS + 0x0fff,
-+ .flags = IORESOURCE_MEM,
-+ },
-+ {
-+ .start = IXP4XX_UART2_BASE_PHYS,
-+ .end = IXP4XX_UART2_BASE_PHYS + 0x0fff,
-+ .flags = IORESOURCE_MEM,
-+ }
-+};
-+
-+static struct plat_serial8250_port fsg_uart_data[] = {
-+ {
-+ .mapbase = IXP4XX_UART1_BASE_PHYS,
-+ .membase = (char *)IXP4XX_UART1_BASE_VIRT + REG_OFFSET,
-+ .irq = IRQ_IXP4XX_UART1,
-+ .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
-+ .iotype = UPIO_MEM,
-+ .regshift = 2,
-+ .uartclk = IXP4XX_UART_XTAL,
-+ },
-+ {
-+ .mapbase = IXP4XX_UART2_BASE_PHYS,
-+ .membase = (char *)IXP4XX_UART2_BASE_VIRT + REG_OFFSET,
-+ .irq = IRQ_IXP4XX_UART2,
-+ .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
-+ .iotype = UPIO_MEM,
-+ .regshift = 2,
-+ .uartclk = IXP4XX_UART_XTAL,
-+ },
-+ { }
-+};
-+
-+static struct platform_device fsg_uart = {
-+ .name = "serial8250",
-+ .id = PLAT8250_DEV_PLATFORM,
-+ .dev = {
-+ .platform_data = fsg_uart_data,
-+ },
-+ .num_resources = ARRAY_SIZE(fsg_uart_resources),
-+ .resource = fsg_uart_resources,
-+};
-+
-+static struct platform_device fsg_leds = {
-+ .name = "fsg-led",
-+ .id = -1,
-+};
-+
-+/* Built-in 10/100 Ethernet MAC interfaces */
-+static struct eth_plat_info fsg_plat_eth[] = {
-+ {
-+ .phy = 5,
-+ .rxq = 3,
-+ .txreadyq = 20,
-+ }, {
-+ .phy = 4,
-+ .rxq = 4,
-+ .txreadyq = 21,
-+ }
-+};
-+
-+static struct platform_device fsg_eth[] = {
-+ {
-+ .name = "ixp4xx_eth",
-+ .id = IXP4XX_ETH_NPEB,
-+ .dev = {
-+ .platform_data = fsg_plat_eth,
-+ },
-+ }, {
-+ .name = "ixp4xx_eth",
-+ .id = IXP4XX_ETH_NPEC,
-+ .dev = {
-+ .platform_data = fsg_plat_eth + 1,
-+ },
-+ }
-+};
-+
-+static struct platform_device *fsg_devices[] __initdata = {
-+ &fsg_i2c_gpio,
-+ &fsg_flash,
-+ &fsg_leds,
-+ &fsg_eth[0],
-+ &fsg_eth[1],
-+};
-+
-+static irqreturn_t fsg_power_handler(int irq, void *dev_id)
-+{
-+ /* Signal init to do the ctrlaltdel action, this will bypass init if
-+ * it hasn't started and do a kernel_restart.
-+ */
-+ ctrl_alt_del();
-+
-+ return IRQ_HANDLED;
-+}
-+
-+static irqreturn_t fsg_reset_handler(int irq, void *dev_id)
-+{
-+ /* This is the paper-clip reset which does an emergency reboot. */
-+ printk(KERN_INFO "Restarting system.\n");
-+ machine_restart(NULL);
-+
-+ /* This should never be reached. */
-+ return IRQ_HANDLED;
-+}
-+
-+static void __init fsg_init(void)
-+{
-+ DECLARE_MAC_BUF(mac_buf);
-+ uint8_t __iomem *f;
-+ int i;
-+
-+ ixp4xx_sys_init();
-+
-+ fsg_flash_resource.start = IXP4XX_EXP_BUS_BASE(0);
-+ fsg_flash_resource.end =
-+ IXP4XX_EXP_BUS_BASE(0) + ixp4xx_exp_bus_size - 1;
-+
-+ *IXP4XX_EXP_CS0 |= IXP4XX_FLASH_WRITABLE;
-+ *IXP4XX_EXP_CS1 = *IXP4XX_EXP_CS0;
-+
-+ /* Configure CS2 for operation, 8bit and writable */
-+ *IXP4XX_EXP_CS2 = 0xbfff0002;
-+
-+ i2c_register_board_info(0, fsg_i2c_board_info,
-+ ARRAY_SIZE(fsg_i2c_board_info));
-+
-+ /* This is only useful on a modified machine, but it is valuable
-+ * to have it first in order to see debug messages, and so that
-+ * it does *not* get removed if platform_add_devices fails!
-+ */
-+ (void)platform_device_register(&fsg_uart);
-+
-+ platform_add_devices(fsg_devices, ARRAY_SIZE(fsg_devices));
-+
-+ if (request_irq(gpio_to_irq(FSG_RB_GPIO), &fsg_reset_handler,
-+ IRQF_DISABLED | IRQF_TRIGGER_LOW,
-+ "FSG reset button", NULL) < 0) {
-+
-+ printk(KERN_DEBUG "Reset Button IRQ %d not available\n",
-+ gpio_to_irq(FSG_RB_GPIO));
-+ }
-+
-+ if (request_irq(gpio_to_irq(FSG_SB_GPIO), &fsg_power_handler,
-+ IRQF_DISABLED | IRQF_TRIGGER_LOW,
-+ "FSG power button", NULL) < 0) {
-+
-+ printk(KERN_DEBUG "Power Button IRQ %d not available\n",
-+ gpio_to_irq(FSG_SB_GPIO));
-+ }
-+
-+ /*
-+ * Map in a portion of the flash and read the MAC addresses.
-+ * Since it is stored in BE in the flash itself, we need to
-+ * byteswap it if we're in LE mode.
-+ */
-+ f = ioremap(IXP4XX_EXP_BUS_BASE(0), 0x400000);
-+ if (f) {
-+#ifdef __ARMEB__
-+ for (i = 0; i < 6; i++) {
-+ fsg_plat_eth[0].hwaddr[i] = readb(f + 0x3C0422 + i);
-+ fsg_plat_eth[1].hwaddr[i] = readb(f + 0x3C043B + i);
-+ }
-+#else
-+
-+ /*
-+ Endian-swapped reads from unaligned addresses are
-+ required to extract the two MACs from the big-endian
-+ Redboot config area in flash.
-+ */
-+
-+ fsg_plat_eth[0].hwaddr[0] = readb(f + 0x3C0421);
-+ fsg_plat_eth[0].hwaddr[1] = readb(f + 0x3C0420);
-+ fsg_plat_eth[0].hwaddr[2] = readb(f + 0x3C0427);
-+ fsg_plat_eth[0].hwaddr[3] = readb(f + 0x3C0426);
-+ fsg_plat_eth[0].hwaddr[4] = readb(f + 0x3C0425);
-+ fsg_plat_eth[0].hwaddr[5] = readb(f + 0x3C0424);
-+
-+ fsg_plat_eth[1].hwaddr[0] = readb(f + 0x3C0439);
-+ fsg_plat_eth[1].hwaddr[1] = readb(f + 0x3C043F);
-+ fsg_plat_eth[1].hwaddr[2] = readb(f + 0x3C043E);
-+ fsg_plat_eth[1].hwaddr[3] = readb(f + 0x3C043D);
-+ fsg_plat_eth[1].hwaddr[4] = readb(f + 0x3C043C);
-+ fsg_plat_eth[1].hwaddr[5] = readb(f + 0x3C0443);
-+#endif
-+ iounmap(f);
-+ }
-+ printk(KERN_INFO "FSG: Using MAC address %s for port 0\n",
-+ print_mac(mac_buf, fsg_plat_eth[0].hwaddr));
-+ printk(KERN_INFO "FSG: Using MAC address %s for port 1\n",
-+ print_mac(mac_buf, fsg_plat_eth[1].hwaddr));
-+
-+}
-+
-+MACHINE_START(FSG, "Freecom FSG-3")
-+ /* Maintainer: www.nslu2-linux.org */
-+ .phys_io = IXP4XX_PERIPHERAL_BASE_PHYS,
-+ .io_pg_offst = ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xfffc,
-+ .map_io = ixp4xx_map_io,
-+ .init_irq = ixp4xx_init_irq,
-+ .timer = &ixp4xx_timer,
-+ .boot_params = 0x0100,
-+ .init_machine = fsg_init,
-+MACHINE_END
-+
---- /dev/null
-+++ b/include/asm-arm/arch-ixp4xx/fsg.h
-@@ -0,0 +1,50 @@
-+/*
-+ * include/asm-arm/arch-ixp4xx/fsg.h
-+ *
-+ * Freecom FSG-3 platform specific definitions
-+ *
-+ * Author: Rod Whitby <rod@whitby.id.au>
-+ * Author: Tomasz Chmielewski <mangoo@wpkg.org>
-+ * Maintainers: http://www.nslu2-linux.org
-+ *
-+ * Based on coyote.h by
-+ * Copyright 2004 (c) MontaVista, Software, Inc.
-+ *
-+ * This file is licensed under the terms of the GNU General Public
-+ * License version 2. This program is licensed "as is" without any
-+ * warranty of any kind, whether express or implied.
-+ */
-+
-+#ifndef __ASM_ARCH_HARDWARE_H__
-+#error "Do not include this directly, instead #include <asm/hardware.h>"
-+#endif
-+
-+#define FSG_SDA_PIN 12
-+#define FSG_SCL_PIN 13
-+
-+/*
-+ * FSG PCI IRQs
-+ */
-+#define FSG_PCI_MAX_DEV 3
-+#define FSG_PCI_IRQ_LINES 3
-+
-+
-+/* PCI controller GPIO to IRQ pin mappings */
-+#define FSG_PCI_INTA_PIN 6
-+#define FSG_PCI_INTB_PIN 7
-+#define FSG_PCI_INTC_PIN 5
-+
-+/* Buttons */
-+
-+#define FSG_SB_GPIO 4 /* sync button */
-+#define FSG_RB_GPIO 9 /* reset button */
-+#define FSG_UB_GPIO 10 /* usb button */
-+
-+/* LEDs */
-+
-+#define FSG_LED_WLAN_BIT 0
-+#define FSG_LED_WAN_BIT 1
-+#define FSG_LED_SATA_BIT 2
-+#define FSG_LED_USB_BIT 4
-+#define FSG_LED_RING_BIT 5
-+#define FSG_LED_SYNC_BIT 7
---- a/include/asm-arm/arch-ixp4xx/hardware.h
-+++ b/include/asm-arm/arch-ixp4xx/hardware.h
-@@ -45,5 +45,6 @@
- #include "nslu2.h"
- #include "nas100d.h"
- #include "dsmg600.h"
-+#include "fsg.h"
-
- #endif /* _ASM_ARCH_HARDWARE_H */
---- a/include/asm-arm/arch-ixp4xx/irqs.h
-+++ b/include/asm-arm/arch-ixp4xx/irqs.h
-@@ -128,4 +128,11 @@
- #define IRQ_DSMG600_PCI_INTE IRQ_IXP4XX_GPIO7
- #define IRQ_DSMG600_PCI_INTF IRQ_IXP4XX_GPIO6
-
-+/*
-+ * Freecom FSG-3 Board IRQs
-+ */
-+#define IRQ_FSG_PCI_INTA IRQ_IXP4XX_GPIO6
-+#define IRQ_FSG_PCI_INTB IRQ_IXP4XX_GPIO7
-+#define IRQ_FSG_PCI_INTC IRQ_IXP4XX_GPIO5
-+
- #endif
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-01 01:25:51 +0000