diff options
Diffstat (limited to 'target/linux/ifxmips/files-2.6.30/arch/mips/include/asm/mach-ifxmips/ifxmips_gptu.h')
| -rw-r--r-- | target/linux/ifxmips/files-2.6.30/arch/mips/include/asm/mach-ifxmips/ifxmips_gptu.h | 155 |
1 files changed, 0 insertions, 155 deletions
diff --git a/target/linux/ifxmips/files-2.6.30/arch/mips/include/asm/mach-ifxmips/ifxmips_gptu.h b/target/linux/ifxmips/files-2.6.30/arch/mips/include/asm/mach-ifxmips/ifxmips_gptu.h deleted file mode 100644 index 330c3cfd5..000000000 --- a/target/linux/ifxmips/files-2.6.30/arch/mips/include/asm/mach-ifxmips/ifxmips_gptu.h +++ /dev/null @@ -1,155 +0,0 @@ -#ifndef __DANUBE_GPTU_DEV_H__2005_07_26__10_19__ -#define __DANUBE_GPTU_DEV_H__2005_07_26__10_19__ - - -/****************************************************************************** - Copyright (c) 2002, Infineon Technologies. All rights reserved. - - No Warranty - Because the program is licensed free of charge, there is no warranty for - the program, to the extent permitted by applicable law. Except when - otherwise stated in writing the copyright holders and/or other parties - provide the program "as is" without warranty of any kind, either - expressed or implied, including, but not limited to, the implied - warranties of merchantability and fitness for a particular purpose. The - entire risk as to the quality and performance of the program is with - you. should the program prove defective, you assume the cost of all - necessary servicing, repair or correction. - - In no event unless required by applicable law or agreed to in writing - will any copyright holder, or any other party who may modify and/or - redistribute the program as permitted above, be liable to you for - damages, including any general, special, incidental or consequential - damages arising out of the use or inability to use the program - (including but not limited to loss of data or data being rendered - inaccurate or losses sustained by you or third parties or a failure of - the program to operate with any other programs), even if such holder or - other party has been advised of the possibility of such damages. -******************************************************************************/ - - -/* - * #################################### - * Definition - * #################################### - */ - -/* - * Available Timer/Counter Index - */ -#define TIMER(n, X) (n * 2 + (X ? 1 : 0)) -#define TIMER_ANY 0x00 -#define TIMER1A TIMER(1, 0) -#define TIMER1B TIMER(1, 1) -#define TIMER2A TIMER(2, 0) -#define TIMER2B TIMER(2, 1) -#define TIMER3A TIMER(3, 0) -#define TIMER3B TIMER(3, 1) - -/* - * Flag of Timer/Counter - * These flags specify the way in which timer is configured. - */ -/* Bit size of timer/counter. */ -#define TIMER_FLAG_16BIT 0x0000 -#define TIMER_FLAG_32BIT 0x0001 -/* Switch between timer and counter. */ -#define TIMER_FLAG_TIMER 0x0000 -#define TIMER_FLAG_COUNTER 0x0002 -/* Stop or continue when overflowing/underflowing. */ -#define TIMER_FLAG_ONCE 0x0000 -#define TIMER_FLAG_CYCLIC 0x0004 -/* Count up or counter down. */ -#define TIMER_FLAG_UP 0x0000 -#define TIMER_FLAG_DOWN 0x0008 -/* Count on specific level or edge. */ -#define TIMER_FLAG_HIGH_LEVEL_SENSITIVE 0x0000 -#define TIMER_FLAG_LOW_LEVEL_SENSITIVE 0x0040 -#define TIMER_FLAG_RISE_EDGE 0x0010 -#define TIMER_FLAG_FALL_EDGE 0x0020 -#define TIMER_FLAG_ANY_EDGE 0x0030 -/* Signal is syncronous to module clock or not. */ -#define TIMER_FLAG_UNSYNC 0x0000 -#define TIMER_FLAG_SYNC 0x0080 -/* Different interrupt handle type. */ -#define TIMER_FLAG_NO_HANDLE 0x0000 -#if defined(__KERNEL__) - #define TIMER_FLAG_CALLBACK_IN_IRQ 0x0100 -#endif // defined(__KERNEL__) -#define TIMER_FLAG_SIGNAL 0x0300 -/* Internal clock source or external clock source */ -#define TIMER_FLAG_INT_SRC 0x0000 -#define TIMER_FLAG_EXT_SRC 0x1000 - - -/* - * ioctl Command - */ -#define GPTU_REQUEST_TIMER 0x01 /* General method to setup timer/counter. */ -#define GPTU_FREE_TIMER 0x02 /* Free timer/counter. */ -#define GPTU_START_TIMER 0x03 /* Start or resume timer/counter. */ -#define GPTU_STOP_TIMER 0x04 /* Suspend timer/counter. */ -#define GPTU_GET_COUNT_VALUE 0x05 /* Get current count value. */ -#define GPTU_CALCULATE_DIVIDER 0x06 /* Calculate timer divider from given freq.*/ -#define GPTU_SET_TIMER 0x07 /* Simplified method to setup timer. */ -#define GPTU_SET_COUNTER 0x08 /* Simplified method to setup counter. */ - -/* - * Data Type Used to Call ioctl - */ -struct gptu_ioctl_param { - unsigned int timer; /* In command GPTU_REQUEST_TIMER, GPTU_SET_TIMER, and * - * GPTU_SET_COUNTER, this field is ID of expected * - * timer/counter. If it's zero, a timer/counter would * - * be dynamically allocated and ID would be stored in * - * this field. * - * In command GPTU_GET_COUNT_VALUE, this field is * - * ignored. * - * In other command, this field is ID of timer/counter * - * allocated. */ - unsigned int flag; /* In command GPTU_REQUEST_TIMER, GPTU_SET_TIMER, and * - * GPTU_SET_COUNTER, this field contains flags to * - * specify how to configure timer/counter. * - * In command GPTU_START_TIMER, zero indicate start * - * and non-zero indicate resume timer/counter. * - * In other command, this field is ignored. */ - unsigned long value; /* In command GPTU_REQUEST_TIMER, this field contains * - * init/reload value. * - * In command GPTU_SET_TIMER, this field contains * - * frequency (0.001Hz) of timer. * - * In command GPTU_GET_COUNT_VALUE, current count * - * value would be stored in this field. * - * In command GPTU_CALCULATE_DIVIDER, this field * - * contains frequency wanted, and after calculation, * - * divider would be stored in this field to overwrite * - * the frequency. * - * In other command, this field is ignored. */ - int pid; /* In command GPTU_REQUEST_TIMER and GPTU_SET_TIMER, * - * if signal is required, this field contains process * - * ID to which signal would be sent. * - * In other command, this field is ignored. */ - int sig; /* In command GPTU_REQUEST_TIMER and GPTU_SET_TIMER, * - * if signal is required, this field contains signal * - * number which would be sent. * - * In other command, this field is ignored. */ -}; - -/* - * #################################### - * Data Type - * #################################### - */ -typedef void (*timer_callback)(unsigned long arg); - -extern int ifxmips_request_timer(unsigned int, unsigned int, unsigned long, unsigned long, unsigned long); -extern int ifxmips_free_timer(unsigned int); -extern int ifxmips_start_timer(unsigned int, int); -extern int ifxmips_stop_timer(unsigned int); -extern int ifxmips_reset_counter_flags(u32 timer, u32 flags); -extern int ifxmips_get_count_value(unsigned int, unsigned long *); -extern u32 ifxmips_cal_divider(unsigned long); -extern int ifxmips_set_timer(unsigned int, unsigned int, int, int, unsigned int, unsigned long, unsigned long); -extern int ifxmips_set_counter(unsigned int timer, unsigned int flag, - u32 reload, unsigned long arg1, unsigned long arg2); - -#endif /* __DANUBE_GPTU_DEV_H__2005_07_26__10_19__ */ |