diff options
Diffstat (limited to 'target/linux/amazon/files/drivers/char/admmod.c')
| -rw-r--r-- | target/linux/amazon/files/drivers/char/admmod.c | 1486 |
1 files changed, 0 insertions, 1486 deletions
diff --git a/target/linux/amazon/files/drivers/char/admmod.c b/target/linux/amazon/files/drivers/char/admmod.c deleted file mode 100644 index 0229f53f5..000000000 --- a/target/linux/amazon/files/drivers/char/admmod.c +++ /dev/null @@ -1,1486 +0,0 @@ -/****************************************************************************** - Copyright (c) 2004, Infineon Technologies. All rights reserved. - - No Warranty - Because the program is licensed free of charge, there is no warranty for - the program, to the extent permitted by applicable law. Except when - otherwise stated in writing the copyright holders and/or other parties - provide the program "as is" without warranty of any kind, either - expressed or implied, including, but not limited to, the implied - warranties of merchantability and fitness for a particular purpose. The - entire risk as to the quality and performance of the program is with - you. should the program prove defective, you assume the cost of all - necessary servicing, repair or correction. - - In no event unless required by applicable law or agreed to in writing - will any copyright holder, or any other party who may modify and/or - redistribute the program as permitted above, be liable to you for - damages, including any general, special, incidental or consequential - damages arising out of the use or inability to use the program - (including but not limited to loss of data or data being rendered - inaccurate or losses sustained by you or third parties or a failure of - the program to operate with any other programs), even if such holder or - other party has been advised of the possibility of such damages. - ****************************************************************************** - Module : admmod.c - Date : 2004-09-01 - Description : JoeLin - Remarks: - - Revision: - MarsLin, add to support VLAN - - *****************************************************************************/ -//000001.joelin 2005/06/02 add"ADM6996_MDC_MDIO_MODE" define, -// if define ADM6996_MDC_MDIO_MODE==> ADM6996LC and ADM6996I will be in MDIO/MDC(SMI)(16 bit) mode, -// amazon should contrl ADM6996 by MDC/MDIO pin -// if undef ADM6996_MDC_MDIO_MODE==> ADM6996 will be in EEProm(32 bit) mode, -// amazon should contrl ADM6996 by GPIO15,16,17,18 pin -/* 507281:linmars 2005/07/28 support MDIO/EEPROM config mode */ -/* 509201:linmars remove driver testing codes */ - -#include <linux/module.h> -#include <linux/string.h> -#include <linux/proc_fs.h> -#include <linux/delay.h> -#include <asm/uaccess.h> -#include <linux/init.h> -#include <linux/ioctl.h> -#include <asm/atomic.h> -#include <asm-mips/amazon/amazon.h> -#include <asm-mips/amazon/adm6996.h> -//#include <linux/amazon/adm6996.h> - - -unsigned int ifx_sw_conf[ADM_SW_MAX_PORT_NUM+1] = \ - {ADM_SW_PORT0_CONF, ADM_SW_PORT1_CONF, ADM_SW_PORT2_CONF, \ - ADM_SW_PORT3_CONF, ADM_SW_PORT4_CONF, ADM_SW_PORT5_CONF}; -unsigned int ifx_sw_bits[8] = \ - {0x1, 0x3, 0x7, 0xf, 0x1f, 0x3f, 0x7f, 0xff}; -unsigned int ifx_sw_vlan_port[6] = {0, 2, 4, 6, 7, 8}; -//050613:fchang -/* 507281:linmars start */ -#ifdef CONFIG_SWITCH_ADM6996_MDIO -#define ADM6996_MDC_MDIO_MODE 1 //000001.joelin -#else -#undef ADM6996_MDC_MDIO_MODE -#endif -/* 507281:linmars end */ -#define adm6996i 0 -#define adm6996lc 1 -#define adm6996l 2 -unsigned int adm6996_mode=adm6996i; -/* - initialize GPIO pins. - output mode, low -*/ -void ifx_gpio_init(void) -{ - //GPIO16,17,18 direction:output - //GPIO16,17,18 output 0 - - AMAZON_SW_REG(AMAZON_GPIO_P1_DIR) |= (GPIO_MDIO|GPIO_MDCS|GPIO_MDC); - AMAZON_SW_REG(AMAZON_GPIO_P1_OUT) =AMAZON_SW_REG(AMAZON_GPIO_P1_IN)& ~(GPIO_MDIO|GPIO_MDCS|GPIO_MDC); - -} - -/* read one bit from mdio port */ -int ifx_sw_mdio_readbit(void) -{ - //int val; - - //val = (AMAZON_SW_REG(GPIO_conf0_REG) & GPIO0_INPUT_MASK) >> 8; - //return val; - //GPIO16 - return AMAZON_SW_REG(AMAZON_GPIO_P1_IN)&1; -} - -/* - MDIO mode selection - 1 -> output - 0 -> input - - switch input/output mode of GPIO 0 -*/ -void ifx_mdio_mode(int mode) -{ -// AMAZON_SW_REG(GPIO_conf0_REG) = mode ? GPIO_ENABLEBITS : -// ((GPIO_ENABLEBITS | MDIO_INPUT) & ~MDIO_OUTPUT_EN); - mode?(AMAZON_SW_REG(AMAZON_GPIO_P1_DIR)|=GPIO_MDIO): - (AMAZON_SW_REG(AMAZON_GPIO_P1_DIR)&=~GPIO_MDIO); - /*int r=AMAZON_SW_REG(AMAZON_GPIO_P1_DIR); - mode?(r|=GPIO_MDIO):(r&=~GPIO_MDIO); - AMAZON_SW_REG(AMAZON_GPIO_P1_DIR)=r;*/ -} - -void ifx_mdc_hi(void) -{ - //GPIO_SET_HI(GPIO_MDC); - //AMAZON_SW_REG(AMAZON_GPIO_P1_OUT)|=GPIO_MDC; - /*int r=AMAZON_SW_REG(AMAZON_GPIO_P1_OUT); - r|=GPIO_MDC; - AMAZON_SW_REG(AMAZON_GPIO_P1_OUT)=r;*/ - - AMAZON_SW_REG(AMAZON_GPIO_P1_OUT)=AMAZON_SW_REG(AMAZON_GPIO_P1_IN)|GPIO_MDC; -} - -void ifx_mdio_hi(void) -{ - //GPIO_SET_HI(GPIO_MDIO); - //AMAZON_SW_REG(AMAZON_GPIO_P1_OUT)|=GPIO_MDIO; - /*int r=AMAZON_SW_REG(AMAZON_GPIO_P1_OUT); - r|=GPIO_MDIO; - AMAZON_SW_REG(AMAZON_GPIO_P1_OUT)=r;*/ - - AMAZON_SW_REG(AMAZON_GPIO_P1_OUT)=AMAZON_SW_REG(AMAZON_GPIO_P1_IN)|GPIO_MDIO; -} - -void ifx_mdcs_hi(void) -{ - //GPIO_SET_HI(GPIO_MDCS); - //AMAZON_SW_REG(AMAZON_GPIO_P1_OUT)|=GPIO_MDCS; - /*int r=AMAZON_SW_REG(AMAZON_GPIO_P1_OUT); - r|=GPIO_MDCS; - AMAZON_SW_REG(AMAZON_GPIO_P1_OUT)=r;*/ - - AMAZON_SW_REG(AMAZON_GPIO_P1_OUT)=AMAZON_SW_REG(AMAZON_GPIO_P1_IN)|GPIO_MDCS; -} - -void ifx_mdc_lo(void) -{ - //GPIO_SET_LOW(GPIO_MDC); - //AMAZON_SW_REG(AMAZON_GPIO_P1_OUT)&=~GPIO_MDC; - /*int r=AMAZON_SW_REG(AMAZON_GPIO_P1_OUT); - r&=~GPIO_MDC; - AMAZON_SW_REG(AMAZON_GPIO_P1_OUT)=r;*/ - - AMAZON_SW_REG(AMAZON_GPIO_P1_OUT)=AMAZON_SW_REG(AMAZON_GPIO_P1_IN)&(~GPIO_MDC); -} - -void ifx_mdio_lo(void) -{ - //GPIO_SET_LOW(GPIO_MDIO); - //AMAZON_SW_REG(AMAZON_GPIO_P1_OUT)&=~GPIO_MDIO; - /*int r=AMAZON_SW_REG(AMAZON_GPIO_P1_OUT); - r&=~GPIO_MDIO; - AMAZON_SW_REG(AMAZON_GPIO_P1_OUT)=r;*/ - - AMAZON_SW_REG(AMAZON_GPIO_P1_OUT)=AMAZON_SW_REG(AMAZON_GPIO_P1_IN)&(~GPIO_MDIO); -} - -void ifx_mdcs_lo(void) -{ - //GPIO_SET_LOW(GPIO_MDCS); - //AMAZON_SW_REG(AMAZON_GPIO_P1_OUT)&=~GPIO_MDCS; - /*int r=AMAZON_SW_REG(AMAZON_GPIO_P1_OUT); - r&=~GPIO_MDCS; - AMAZON_SW_REG(AMAZON_GPIO_P1_OUT)=r;*/ - - AMAZON_SW_REG(AMAZON_GPIO_P1_OUT)=AMAZON_SW_REG(AMAZON_GPIO_P1_IN)&(~GPIO_MDCS); -} - -/* - mdc pulse - 0 -> 1 -> 0 -*/ -static void ifx_sw_mdc_pulse(void) -{ - ifx_mdc_lo(); - udelay(ADM_SW_MDC_DOWN_DELAY); - ifx_mdc_hi(); - udelay(ADM_SW_MDC_UP_DELAY); - ifx_mdc_lo(); -} - -/* - mdc toggle - 1 -> 0 -*/ -static void ifx_sw_mdc_toggle(void) -{ - ifx_mdc_hi(); - udelay(ADM_SW_MDC_UP_DELAY); - ifx_mdc_lo(); - udelay(ADM_SW_MDC_DOWN_DELAY); -} - -/* - enable eeprom write - For ATC 93C66 type EEPROM; accessing ADM6996 internal EEPROM type registers -*/ -static void ifx_sw_eeprom_write_enable(void) -{ - unsigned int op; - - ifx_mdcs_lo(); - ifx_mdc_lo(); - ifx_mdio_hi(); - udelay(ADM_SW_CS_DELAY); - /* enable chip select */ - ifx_mdcs_hi(); - udelay(ADM_SW_CS_DELAY); - /* start bit */ - ifx_mdio_hi(); - ifx_sw_mdc_pulse(); - - /* eeprom write enable */ - op = ADM_SW_BIT_MASK_4; - while (op) - { - if (op & ADM_SW_EEPROM_WRITE_ENABLE) - ifx_mdio_hi(); - else - ifx_mdio_lo(); - - ifx_sw_mdc_pulse(); - op >>= 1; - } - - op = ADM_SW_BIT_MASK_1 << (EEPROM_TYPE - 3); - while (op) - { - ifx_mdio_lo(); - ifx_sw_mdc_pulse(); - op >>= 1; - } - /* disable chip select */ - ifx_mdcs_lo(); - udelay(ADM_SW_CS_DELAY); - ifx_sw_mdc_pulse(); -} - -/* - disable eeprom write -*/ -static void ifx_sw_eeprom_write_disable(void) -{ - unsigned int op; - - ifx_mdcs_lo(); - ifx_mdc_lo(); - ifx_mdio_hi(); - udelay(ADM_SW_CS_DELAY); - /* enable chip select */ - ifx_mdcs_hi(); - udelay(ADM_SW_CS_DELAY); - - /* start bit */ - ifx_mdio_hi(); - ifx_sw_mdc_pulse(); - /* eeprom write disable */ - op = ADM_SW_BIT_MASK_4; - while (op) - { - if (op & ADM_SW_EEPROM_WRITE_DISABLE) - ifx_mdio_hi(); - else - ifx_mdio_lo(); - - ifx_sw_mdc_pulse(); - op >>= 1; - } - - op = ADM_SW_BIT_MASK_1 << (EEPROM_TYPE - 3); - while (op) - { - ifx_mdio_lo(); - - ifx_sw_mdc_pulse(); - op >>= 1; - } - /* disable chip select */ - ifx_mdcs_lo(); - udelay(ADM_SW_CS_DELAY); - ifx_sw_mdc_pulse(); -} - -/* - read registers from ADM6996 - serial registers start at 0x200 (addr bit 9 = 1b) - EEPROM registers -> 16bits; Serial registers -> 32bits -*/ -#ifdef ADM6996_MDC_MDIO_MODE //smi mode//000001.joelin -static int ifx_sw_read_adm6996i_smi(unsigned int addr, unsigned int *dat) -{ - addr=(addr<<16)&0x3ff0000; - AMAZON_SW_REG(AMAZON_SW_MDIO_ACC) =(0xC0000000|addr); - while ((AMAZON_SW_REG(AMAZON_SW_MDIO_ACC))&0x80000000){}; - *dat=((AMAZON_SW_REG(AMAZON_SW_MDIO_ACC))&0x0FFFF); - return 0; -} -#endif - -static int ifx_sw_read_adm6996i(unsigned int addr, unsigned int *dat) -{ - unsigned int op; - - ifx_gpio_init(); - - ifx_mdcs_hi(); - udelay(ADM_SW_CS_DELAY); - - ifx_mdcs_lo(); - ifx_mdc_lo(); - ifx_mdio_lo(); - - udelay(ADM_SW_CS_DELAY); - - /* preamble, 32 bit 1 */ - ifx_mdio_hi(); - op = ADM_SW_BIT_MASK_32; - while (op) - { - ifx_sw_mdc_pulse(); - op >>= 1; - } - - /* command start (01b) */ - op = ADM_SW_BIT_MASK_2; - while (op) - { - if (op & ADM_SW_SMI_START) - ifx_mdio_hi(); - else - ifx_mdio_lo(); - - ifx_sw_mdc_pulse(); - op >>= 1; - } - - /* read command (10b) */ - op = ADM_SW_BIT_MASK_2; - while (op) - { - if (op & ADM_SW_SMI_READ) - ifx_mdio_hi(); - else - ifx_mdio_lo(); - - ifx_sw_mdc_pulse(); - op >>= 1; - } - - /* send address A9 ~ A0 */ - op = ADM_SW_BIT_MASK_10; - while (op) - { - if (op & addr) - ifx_mdio_hi(); - else - ifx_mdio_lo(); - - ifx_sw_mdc_pulse(); - op >>= 1; - } - - /* turnaround bits */ - op = ADM_SW_BIT_MASK_2; - ifx_mdio_hi(); - while (op) - { - ifx_sw_mdc_pulse(); - op >>= 1; - } - - udelay(ADM_SW_MDC_DOWN_DELAY); - - /* set MDIO pin to input mode */ - ifx_mdio_mode(ADM_SW_MDIO_INPUT); - - /* start read data */ - *dat = 0; -//adm6996i op = ADM_SW_BIT_MASK_32; - op = ADM_SW_BIT_MASK_16;//adm6996i - while (op) - { - *dat <<= 1; - if (ifx_sw_mdio_readbit()) *dat |= 1; - ifx_sw_mdc_toggle(); - - op >>= 1; - } - - /* set MDIO to output mode */ - ifx_mdio_mode(ADM_SW_MDIO_OUTPUT); - - /* dummy clock */ - op = ADM_SW_BIT_MASK_4; - ifx_mdio_lo(); - while(op) - { - ifx_sw_mdc_pulse(); - op >>= 1; - } - - ifx_mdc_lo(); - ifx_mdio_lo(); - ifx_mdcs_hi(); - - /* EEPROM registers */ -//adm6996i if (!(addr & 0x200)) -//adm6996i { -//adm6996i if (addr % 2) -//adm6996i *dat >>= 16; -//adm6996i else -//adm6996i *dat &= 0xffff; -//adm6996i } - - return 0; -} -//adm6996 -static int ifx_sw_read_adm6996l(unsigned int addr, unsigned int *dat) -{ - unsigned int op; - - ifx_gpio_init(); - - ifx_mdcs_hi(); - udelay(ADM_SW_CS_DELAY); - - ifx_mdcs_lo(); - ifx_mdc_lo(); - ifx_mdio_lo(); - - udelay(ADM_SW_CS_DELAY); - - /* preamble, 32 bit 1 */ - ifx_mdio_hi(); - op = ADM_SW_BIT_MASK_32; - while (op) - { - ifx_sw_mdc_pulse(); - op >>= 1; - } - - /* command start (01b) */ - op = ADM_SW_BIT_MASK_2; - while (op) - { - if (op & ADM_SW_SMI_START) - ifx_mdio_hi(); - else - ifx_mdio_lo(); - - ifx_sw_mdc_pulse(); - op >>= 1; - } - - /* read command (10b) */ - op = ADM_SW_BIT_MASK_2; - while (op) - { - if (op & ADM_SW_SMI_READ) - ifx_mdio_hi(); - else - ifx_mdio_lo(); - - ifx_sw_mdc_pulse(); - op >>= 1; - } - - /* send address A9 ~ A0 */ - op = ADM_SW_BIT_MASK_10; - while (op) - { - if (op & addr) - ifx_mdio_hi(); - else - ifx_mdio_lo(); - - ifx_sw_mdc_pulse(); - op >>= 1; - } - - /* turnaround bits */ - op = ADM_SW_BIT_MASK_2; - ifx_mdio_hi(); - while (op) - { - ifx_sw_mdc_pulse(); - op >>= 1; - } - - udelay(ADM_SW_MDC_DOWN_DELAY); - - /* set MDIO pin to input mode */ - ifx_mdio_mode(ADM_SW_MDIO_INPUT); - - /* start read data */ - *dat = 0; - op = ADM_SW_BIT_MASK_32; - while (op) - { - *dat <<= 1; - if (ifx_sw_mdio_readbit()) *dat |= 1; - ifx_sw_mdc_toggle(); - - op >>= 1; - } - - /* set MDIO to output mode */ - ifx_mdio_mode(ADM_SW_MDIO_OUTPUT); - - /* dummy clock */ - op = ADM_SW_BIT_MASK_4; - ifx_mdio_lo(); - while(op) - { - ifx_sw_mdc_pulse(); - op >>= 1; - } - - ifx_mdc_lo(); - ifx_mdio_lo(); - ifx_mdcs_hi(); - - /* EEPROM registers */ - if (!(addr & 0x200)) - { - if (addr % 2) - *dat >>= 16; - else - *dat &= 0xffff; - } - - return 0; -} - -static int ifx_sw_read(unsigned int addr, unsigned int *dat) -{ -#ifdef ADM6996_MDC_MDIO_MODE //smi mode ////000001.joelin - ifx_sw_read_adm6996i_smi(addr,dat); -#else - if (adm6996_mode==adm6996i) ifx_sw_read_adm6996i(addr,dat); - else ifx_sw_read_adm6996l(addr,dat); -#endif - return 0; - -} - -/* - write register to ADM6996 eeprom registers -*/ -//for adm6996i -start -#ifdef ADM6996_MDC_MDIO_MODE //smi mode //000001.joelin -static int ifx_sw_write_adm6996i_smi(unsigned int addr, unsigned int dat) -{ - - AMAZON_SW_REG(AMAZON_SW_MDIO_ACC) = ((addr<<16)&0x3ff0000)|dat|0x80000000; - while ((AMAZON_SW_REG(AMAZON_SW_MDIO_ACC))&0x80000000){}; - - return 0; - -} -#endif //ADM6996_MDC_MDIO_MODE //000001.joelin - -static int ifx_sw_write_adm6996i(unsigned int addr, unsigned int dat) -{ - unsigned int op; - - ifx_gpio_init(); - - ifx_mdcs_hi(); - udelay(ADM_SW_CS_DELAY); - - ifx_mdcs_lo(); - ifx_mdc_lo(); - ifx_mdio_lo(); - - udelay(ADM_SW_CS_DELAY); - - /* preamble, 32 bit 1 */ - ifx_mdio_hi(); - op = ADM_SW_BIT_MASK_32; - while (op) - { - ifx_sw_mdc_pulse(); - op >>= 1; - } - - /* command start (01b) */ - op = ADM_SW_BIT_MASK_2; - while (op) - { - if (op & ADM_SW_SMI_START) - ifx_mdio_hi(); - else - ifx_mdio_lo(); - - ifx_sw_mdc_pulse(); - op >>= 1; - } - - /* write command (01b) */ - op = ADM_SW_BIT_MASK_2; - while (op) - { - if (op & ADM_SW_SMI_WRITE) - ifx_mdio_hi(); - else - ifx_mdio_lo(); - - ifx_sw_mdc_pulse(); - op >>= 1; - } - - /* send address A9 ~ A0 */ - op = ADM_SW_BIT_MASK_10; - while (op) - { - if (op & addr) - ifx_mdio_hi(); - else - ifx_mdio_lo(); - - ifx_sw_mdc_pulse(); - op >>= 1; - } - - /* turnaround bits */ - op = ADM_SW_BIT_MASK_2; - ifx_mdio_hi(); - while (op) - { - ifx_sw_mdc_pulse(); - op >>= 1; - } - - udelay(ADM_SW_MDC_DOWN_DELAY); - - /* set MDIO pin to output mode */ - ifx_mdio_mode(ADM_SW_MDIO_OUTPUT); - - - /* start write data */ - op = ADM_SW_BIT_MASK_16; - while (op) - { - if (op & dat) - ifx_mdio_hi(); - else - ifx_mdio_lo(); - - ifx_sw_mdc_toggle(); - op >>= 1; - } - - // /* set MDIO to output mode */ - // ifx_mdio_mode(ADM_SW_MDIO_OUTPUT); - - /* dummy clock */ - op = ADM_SW_BIT_MASK_4; - ifx_mdio_lo(); - while(op) - { - ifx_sw_mdc_pulse(); - op >>= 1; - } - - ifx_mdc_lo(); - ifx_mdio_lo(); - ifx_mdcs_hi(); - - /* EEPROM registers */ -//adm6996i if (!(addr & 0x200)) -//adm6996i { -//adm6996i if (addr % 2) -//adm6996i *dat >>= 16; -//adm6996i else -//adm6996i *dat &= 0xffff; -//adm6996i } - - return 0; -} -//for adm6996i-end -static int ifx_sw_write_adm6996l(unsigned int addr, unsigned int dat) -{ - unsigned int op; - - ifx_gpio_init(); - - /* enable write */ - ifx_sw_eeprom_write_enable(); - - /* chip select */ - ifx_mdcs_hi(); - udelay(ADM_SW_CS_DELAY); - - /* issue write command */ - /* start bit */ - ifx_mdio_hi(); - ifx_sw_mdc_pulse(); - - /* EEPROM write command */ - op = ADM_SW_BIT_MASK_2; - while (op) - { - if (op & ADM_SW_EEPROM_WRITE) - ifx_mdio_hi(); - else - ifx_mdio_lo(); - - ifx_sw_mdc_pulse(); - op >>= 1; - } - - /* send address A7 ~ A0 */ - op = ADM_SW_BIT_MASK_1 << (EEPROM_TYPE - 1); - - while (op) - { - if (op & addr) - ifx_mdio_hi(); - else - ifx_mdio_lo(); - - ifx_sw_mdc_toggle(); - op >>= 1; - } - - /* start write data */ - op = ADM_SW_BIT_MASK_16; - while (op) - { - if (op & dat) - ifx_mdio_hi(); - else - ifx_mdio_lo(); - - ifx_sw_mdc_toggle(); - op >>= 1; - } - - /* disable cs & wait 1 clock */ - ifx_mdcs_lo(); - udelay(ADM_SW_CS_DELAY); - ifx_sw_mdc_toggle(); - - ifx_sw_eeprom_write_disable(); - - return 0; -} - -static int ifx_sw_write(unsigned int addr, unsigned int dat) -{ -#ifdef ADM6996_MDC_MDIO_MODE //smi mode ////000001.joelin - ifx_sw_write_adm6996i_smi(addr,dat); -#else //000001.joelin - if (adm6996_mode==adm6996i) ifx_sw_write_adm6996i(addr,dat); - else ifx_sw_write_adm6996l(addr,dat); -#endif //000001.joelin - return 0; -} - -/* - do switch PHY reset -*/ -int ifx_sw_reset(void) -{ - /* reset PHY */ - ifx_sw_write(ADM_SW_PHY_RESET, 0); - - return 0; -} - -/* 509201:linmars start */ -#if 0 -/* - check port status -*/ -int ifx_check_port_status(int port) -{ - unsigned int val; - - if ((port < 0) || (port > ADM_SW_MAX_PORT_NUM)) - { - ifx_printf(("error on port number (%d)!!\n", port)); - return -1; - } - - ifx_sw_read(ifx_sw_conf[port], &val); - if (ifx_sw_conf[port]%2) val >>= 16; - /* only 16bits are effective */ - val &= 0xFFFF; - - ifx_printf(("Port %d status (%.8x): \n", port, val)); - - if (val & ADM_SW_PORT_FLOWCTL) - ifx_printf(("\t802.3x flow control supported!\n")); - else - ifx_printf(("\t802.3x flow control not supported!\n")); - - if (val & ADM_SW_PORT_AN) - ifx_printf(("\tAuto negotiation ON!\n")); - else - ifx_printf(("\tAuto negotiation OFF!\n")); - - if (val & ADM_SW_PORT_100M) - ifx_printf(("\tLink at 100M!\n")); - else - ifx_printf(("\tLink at 10M!\n")); - - if (val & ADM_SW_PORT_FULL) - ifx_printf(("\tFull duplex!\n")); - else - ifx_printf(("\tHalf duplex!\n")); - - if (val & ADM_SW_PORT_DISABLE) - ifx_printf(("\tPort disabled!\n")); - else - ifx_printf(("\tPort enabled!\n")); - - if (val & ADM_SW_PORT_TOS) - ifx_printf(("\tTOS enabled!\n")); - else - ifx_printf(("\tTOS disabled!\n")); - - if (val & ADM_SW_PORT_PPRI) - ifx_printf(("\tPort priority first!\n")); - else - ifx_printf(("\tVLAN or TOS priority first!\n")); - - if (val & ADM_SW_PORT_MDIX) - ifx_printf(("\tAuto MDIX!\n")); - else - ifx_printf(("\tNo auto MDIX\n")); - - ifx_printf(("\tPVID: %d\n", \ - ((val >> ADM_SW_PORT_PVID_SHIFT)&ifx_sw_bits[ADM_SW_PORT_PVID_BITS]))); - - return 0; -} -/* - initialize a VLAN - clear all VLAN bits -*/ -int ifx_sw_vlan_init(int vlanid) -{ - ifx_sw_write(ADM_SW_VLAN0_CONF + vlanid, 0); - - return 0; -} - -/* - add a port to certain vlan -*/ -int ifx_sw_vlan_add(int port, int vlanid) -{ - int reg = 0; - - if ((port < 0) || (port > ADM_SW_MAX_PORT_NUM) || (vlanid < 0) || - (vlanid > ADM_SW_MAX_VLAN_NUM)) - { - ifx_printf(("Port number or VLAN number ERROR!!\n")); - return -1; - } - ifx_sw_read(ADM_SW_VLAN0_CONF + vlanid, ®); - reg |= (1 << ifx_sw_vlan_port[port]); - ifx_sw_write(ADM_SW_VLAN0_CONF + vlanid, reg); - - return 0; -} - -/* - delete a given port from certain vlan -*/ -int ifx_sw_vlan_del(int port, int vlanid) -{ - unsigned int reg = 0; - - if ((port < 0) || (port > ADM_SW_MAX_PORT_NUM) || (vlanid < 0) || (vlanid > ADM_SW_MAX_VLAN_NUM)) - { - ifx_printf(("Port number or VLAN number ERROR!!\n")); - return -1; - } - ifx_sw_read(ADM_SW_VLAN0_CONF + vlanid, ®); - reg &= ~(1 << ifx_sw_vlan_port[port]); - ifx_sw_write(ADM_SW_VLAN0_CONF + vlanid, reg); - - return 0; -} - -/* - default VLAN setting - - port 0~3 as untag port and PVID = 1 - VLAN1: port 0~3 and port 5 (MII) -*/ -static int ifx_sw_init(void) -{ - ifx_printf(("Setting default ADM6996 registers... \n")); - - /* MAC clone, 802.1q based VLAN */ - ifx_sw_write(ADM_SW_VLAN_MODE, 0xff30); - /* auto MDIX, PVID=1, untag */ - ifx_sw_write(ADM_SW_PORT0_CONF, 0x840f); - ifx_sw_write(ADM_SW_PORT1_CONF, 0x840f); - ifx_sw_write(ADM_SW_PORT2_CONF, 0x840f); - ifx_sw_write(ADM_SW_PORT3_CONF, 0x840f); - /* auto MDIX, PVID=2, untag */ - ifx_sw_write(ADM_SW_PORT5_CONF, 0x880f); - /* port 0~3 & 5 as VLAN1 */ - ifx_sw_write(ADM_SW_VLAN0_CONF+1, 0x0155); - - return 0; -} -#endif -/* 509201:linmars end */ - -int adm_open(struct inode *node, struct file *filp) -{ - MOD_INC_USE_COUNT; - return 0; -} - -ssize_t adm_read(struct file *filep, char *buf, size_t count, loff_t *ppos) -{ - return count; -} - -ssize_t adm_write(struct file *filep, const char *buf, size_t count, loff_t *ppos) -{ - return count; -} - -/* close */ -int adm_release(struct inode *inode, struct file *filp) -{ - MOD_DEC_USE_COUNT; - return 0; -} - -/* IOCTL function */ -int adm_ioctl(struct inode *inode, struct file *filp, unsigned int cmd, unsigned long args) -{ - PREGRW uREGRW; - unsigned int rtval; - unsigned int val; //6996i - unsigned int control[6] ; //6996i - unsigned int status[6] ; //6996i - - PMACENTRY mMACENTRY;//adm6996i - PPROTOCOLFILTER uPROTOCOLFILTER ;///adm6996i - - if (_IOC_TYPE(cmd) != ADM_MAGIC) - { - printk("adm_ioctl: IOC_TYPE(%x) != ADM_MAGIC(%x)! \n", _IOC_TYPE(cmd), ADM_MAGIC); - return (-EINVAL); - } - - if(_IOC_NR(cmd) >= KEY_IOCTL_MAX_KEY) - { - printk(KERN_WARNING "adm_ioctl: IOC_NR(%x) invalid! \n", _IOC_NR(cmd)); - return (-EINVAL); - } - - switch (cmd) - { - case ADM_IOCTL_REGRW: - { - uREGRW = (PREGRW)kmalloc(sizeof(REGRW), GFP_KERNEL); - rtval = copy_from_user(uREGRW, (PREGRW)args, sizeof(REGRW)); - if (rtval != 0) - { - printk("ADM_IOCTL_REGRW: copy from user FAILED!! \n"); - return (-EFAULT); - } - - switch(uREGRW->mode) - { - case REG_READ: - uREGRW->value = 0x12345678;//inl(uREGRW->addr); - copy_to_user((PREGRW)args, uREGRW, sizeof(REGRW)); - break; - case REG_WRITE: - //outl(uREGRW->value, uREGRW->addr); - break; - - default: - printk("No such Register Read/Write function!! \n"); - return (-EFAULT); - } - kfree(uREGRW); - break; - } - - case ADM_SW_IOCTL_REGRW: - { - unsigned int val = 0xff; - - uREGRW = (PREGRW)kmalloc(sizeof(REGRW), GFP_KERNEL); - rtval = copy_from_user(uREGRW, (PREGRW)args, sizeof(REGRW)); - if (rtval != 0) - { - printk("ADM_IOCTL_REGRW: copy from user FAILED!! \n"); - return (-EFAULT); - } - - switch(uREGRW->mode) - { - case REG_READ: - ifx_sw_read(uREGRW->addr, &val); - uREGRW->value = val; - copy_to_user((PREGRW)args, uREGRW, sizeof(REGRW)); - break; - - case REG_WRITE: - ifx_sw_write(uREGRW->addr, uREGRW->value); - break; - default: - printk("No such Register Read/Write function!! \n"); - return (-EFAULT); - } - kfree(uREGRW); - break; - } -/* 509201:linmars start */ -#if 0 - case ADM_SW_IOCTL_PORTSTS: - for (rtval = 0; rtval < ADM_SW_MAX_PORT_NUM+1; rtval++) - ifx_check_port_status(rtval); - break; - case ADM_SW_IOCTL_INIT: - ifx_sw_init(); - break; -#endif -/* 509201:linmars end */ -//adm6996i - case ADM_SW_IOCTL_MACENTRY_ADD: - case ADM_SW_IOCTL_MACENTRY_DEL: - case ADM_SW_IOCTL_MACENTRY_GET_INIT: - case ADM_SW_IOCTL_MACENTRY_GET_MORE: - - - mMACENTRY = (PMACENTRY)kmalloc(sizeof(MACENTRY), GFP_KERNEL); - rtval = copy_from_user(mMACENTRY, (PMACENTRY)args, sizeof(MACENTRY)); - if (rtval != 0) - { - printk("ADM_SW_IOCTL_MACENTRY: copy from user FAILED!! \n"); - return (-EFAULT); - } - control[0]=(mMACENTRY->mac_addr[1]<<8)+mMACENTRY->mac_addr[0] ; - control[1]=(mMACENTRY->mac_addr[3]<<8)+mMACENTRY->mac_addr[2] ; - control[2]=(mMACENTRY->mac_addr[5]<<8)+mMACENTRY->mac_addr[4] ; - control[3]=(mMACENTRY->fid&0xf)+((mMACENTRY->portmap&0x3f)<<4); - if (((mMACENTRY->info_type)&0x01)) control[4]=(mMACENTRY->ctrl.info_ctrl)+0x1000; //static ,info control - else control[4]=((mMACENTRY->ctrl.age_timer)&0xff);//not static ,agetimer - if (cmd==ADM_SW_IOCTL_MACENTRY_GET_INIT) { - //initial the pointer to the first address - val=0x8000;//busy ,status5[15] - while(val&0x8000){ //check busy ? - ifx_sw_read(0x125, &val); - } - control[5]=0x030;//initial the first address - ifx_sw_write(0x11f,control[5]); - - - val=0x8000;//busy ,status5[15] - while(val&0x8000){ //check busy ? - ifx_sw_read(0x125, &val); - } - - } //if (cmd==ADM_SW_IOCTL_MACENTRY_GET_INIT) - if (cmd==ADM_SW_IOCTL_MACENTRY_ADD) control[5]=0x07;//create a new address - else if (cmd==ADM_SW_IOCTL_MACENTRY_DEL) control[5]=0x01f;//erased an existed address - else if ((cmd==ADM_SW_IOCTL_MACENTRY_GET_INIT)||(cmd==ADM_SW_IOCTL_MACENTRY_GET_MORE)) - control[5]=0x02c;//search by the mac address field - - val=0x8000;//busy ,status5[15] - while(val&0x8000){ //check busy ? - ifx_sw_read(0x125, &val); - } - ifx_sw_write(0x11a,control[0]); - ifx_sw_write(0x11b,control[1]); - ifx_sw_write(0x11c,control[2]); - ifx_sw_write(0x11d,control[3]); - ifx_sw_write(0x11e,control[4]); - ifx_sw_write(0x11f,control[5]); - val=0x8000;//busy ,status5[15] - while(val&0x8000){ //check busy ? - ifx_sw_read(0x125, &val); - } - val=((val&0x7000)>>12);//result ,status5[14:12] - mMACENTRY->result=val; - - if (!val) { - printk(" Command OK!! \n"); - if ((cmd==ADM_SW_IOCTL_MACENTRY_GET_INIT)||(cmd==ADM_SW_IOCTL_MACENTRY_GET_MORE)) { - ifx_sw_read(0x120,&(status[0])); - ifx_sw_read(0x121,&(status[1])); - ifx_sw_read(0x122,&(status[2])); - ifx_sw_read(0x123,&(status[3])); - ifx_sw_read(0x124,&(status[4])); - ifx_sw_read(0x125,&(status[5])); - - - mMACENTRY->mac_addr[0]=(status[0]&0x00ff) ; - mMACENTRY->mac_addr[1]=(status[0]&0xff00)>>8 ; - mMACENTRY->mac_addr[2]=(status[1]&0x00ff) ; - mMACENTRY->mac_addr[3]=(status[1]&0xff00)>>8 ; - mMACENTRY->mac_addr[4]=(status[2]&0x00ff) ; - mMACENTRY->mac_addr[5]=(status[2]&0xff00)>>8 ; - mMACENTRY->fid=(status[3]&0xf); - mMACENTRY->portmap=((status[3]>>4)&0x3f); - if (status[5]&0x2) {//static info_ctrl //status5[1]???? - mMACENTRY->ctrl.info_ctrl=(status[4]&0x00ff); - mMACENTRY->info_type=1; - } - else {//not static age_timer - mMACENTRY->ctrl.age_timer=(status[4]&0x00ff); - mMACENTRY->info_type=0; - } -//status5[13]???? mMACENTRY->occupy=(status[5]&0x02)>>1;//status5[1] - mMACENTRY->occupy=(status[5]&0x02000)>>13;//status5[13] ??? - mMACENTRY->bad=(status[5]&0x04)>>2;//status5[2] - }//if ((cmd==ADM_SW_IOCTL_MACENTRY_GET_INIT)||(cmd==ADM_SW_IOCTL_MACENTRY_GET_MORE)) - - } - else if (val==0x001) - printk(" All Entry Used!! \n"); - else if (val==0x002) - printk(" Entry Not Found!! \n"); - else if (val==0x003) - printk(" Try Next Entry!! \n"); - else if (val==0x005) - printk(" Command Error!! \n"); - else - printk(" UnKnown Error!! \n"); - - copy_to_user((PMACENTRY)args, mMACENTRY,sizeof(MACENTRY)); - - break; - - case ADM_SW_IOCTL_FILTER_ADD: - case ADM_SW_IOCTL_FILTER_DEL: - case ADM_SW_IOCTL_FILTER_GET: - - uPROTOCOLFILTER = (PPROTOCOLFILTER)kmalloc(sizeof(PROTOCOLFILTER), GFP_KERNEL); - rtval = copy_from_user(uPROTOCOLFILTER, (PPROTOCOLFILTER)args, sizeof(PROTOCOLFILTER)); - if (rtval != 0) - { - printk("ADM_SW_IOCTL_FILTER_ADD: copy from user FAILED!! \n"); - return (-EFAULT); - } - - if(cmd==ADM_SW_IOCTL_FILTER_DEL) { //delete filter - uPROTOCOLFILTER->ip_p=00; //delet filter - uPROTOCOLFILTER->action=00; //delete filter - } //delete filter - - ifx_sw_read(((uPROTOCOLFILTER->protocol_filter_num/2)+0x68), &val);//rx68~rx6b,protocol filter0~7 - - if (((uPROTOCOLFILTER->protocol_filter_num)%2)==00){ - if(cmd==ADM_SW_IOCTL_FILTER_GET) uPROTOCOLFILTER->ip_p= val&0x00ff;//get filter ip_p - else val=(val&0xff00)|(uPROTOCOLFILTER->ip_p);//set filter ip_p - } - else { - if(cmd==ADM_SW_IOCTL_FILTER_GET) uPROTOCOLFILTER->ip_p= (val>>8);//get filter ip_p - else val=(val&0x00ff)|((uPROTOCOLFILTER->ip_p)<<8);//set filter ip_p - } - if(cmd!=ADM_SW_IOCTL_FILTER_GET) ifx_sw_write(((uPROTOCOLFILTER->protocol_filter_num/2)+0x68), val);//write rx68~rx6b,protocol filter0~7 - - ifx_sw_read(0x95, &val); //protocol filter action - if(cmd==ADM_SW_IOCTL_FILTER_GET) { - uPROTOCOLFILTER->action= ((val>>(uPROTOCOLFILTER->protocol_filter_num*2))&0x3);//get filter action - copy_to_user((PPROTOCOLFILTER)args, uPROTOCOLFILTER, sizeof(PROTOCOLFILTER)); - - } - else { - val=(val&(~(0x03<<(uPROTOCOLFILTER->protocol_filter_num*2))))|(((uPROTOCOLFILTER->action)&0x03)<<(uPROTOCOLFILTER->protocol_filter_num*2)); - // printk("%d----\n",val); - ifx_sw_write(0x95, val); //write protocol filter action - } - - break; -//adm6996i - - /* others */ - default: - return -EFAULT; - } - /* end of switch */ - return 0; -} - -/* Santosh: handle IGMP protocol filter ADD/DEL/GET */ -int adm_process_protocol_filter_request (unsigned int cmd, PPROTOCOLFILTER uPROTOCOLFILTER) -{ - unsigned int val; //6996i - - if(cmd==ADM_SW_IOCTL_FILTER_DEL) { //delete filter - uPROTOCOLFILTER->ip_p=00; //delet filter - uPROTOCOLFILTER->action=00; //delete filter - } //delete filter - - ifx_sw_read(((uPROTOCOLFILTER->protocol_filter_num/2)+0x68), &val);//rx68~rx6b,protocol filter0~7 - - if (((uPROTOCOLFILTER->protocol_filter_num)%2)==00){ - if(cmd==ADM_SW_IOCTL_FILTER_GET) uPROTOCOLFILTER->ip_p= val&0x00ff;//get filter ip_p - else val=(val&0xff00)|(uPROTOCOLFILTER->ip_p);//set filter ip_p - } - else { - if(cmd==ADM_SW_IOCTL_FILTER_GET) uPROTOCOLFILTER->ip_p= (val>>8);//get filter ip_p - else val=(val&0x00ff)|((uPROTOCOLFILTER->ip_p)<<8);//set filter ip_p - } - if(cmd!=ADM_SW_IOCTL_FILTER_GET) ifx_sw_write(((uPROTOCOLFILTER->protocol_filter_num/2)+0x68), val);//write rx68~rx6b,protocol filter0~7 - - ifx_sw_read(0x95, &val); //protocol filter action - if(cmd==ADM_SW_IOCTL_FILTER_GET) { - uPROTOCOLFILTER->action= ((val>>(uPROTOCOLFILTER->protocol_filter_num*2))&0x3);//get filter action - } - else { - val=(val&(~(0x03<<(uPROTOCOLFILTER->protocol_filter_num*2))))|(((uPROTOCOLFILTER->action)&0x03)<<(uPROTOCOLFILTER->protocol_filter_num*2)); - ifx_sw_write(0x95, val); //write protocol filter action - } - - return 0; -} - - -/* Santosh: function for MAC ENTRY ADD/DEL/GET */ - -int adm_process_mac_table_request (unsigned int cmd, PMACENTRY mMACENTRY) -{ - unsigned int rtval; - unsigned int val; //6996i - unsigned int control[6] ; //6996i - unsigned int status[6] ; //6996i - - // printk ("adm_process_mac_table_request: enter\n"); - - control[0]=(mMACENTRY->mac_addr[1]<<8)+mMACENTRY->mac_addr[0] ; - control[1]=(mMACENTRY->mac_addr[3]<<8)+mMACENTRY->mac_addr[2] ; - control[2]=(mMACENTRY->mac_addr[5]<<8)+mMACENTRY->mac_addr[4] ; - control[3]=(mMACENTRY->fid&0xf)+((mMACENTRY->portmap&0x3f)<<4); - - if (((mMACENTRY->info_type)&0x01)) control[4]=(mMACENTRY->ctrl.info_ctrl)+0x1000; //static ,info control - else control[4]=((mMACENTRY->ctrl.age_timer)&0xff);//not static ,agetimer - if (cmd==ADM_SW_IOCTL_MACENTRY_GET_INIT) { - //initial the pointer to the first address - val=0x8000;//busy ,status5[15] - while(val&0x8000){ //check busy ? - ifx_sw_read(0x125, &val); - } - control[5]=0x030;//initial the first address - ifx_sw_write(0x11f,control[5]); - - - val=0x8000;//busy ,status5[15] - while(val&0x8000){ //check busy ? - ifx_sw_read(0x125, &val); - } - - } //if (cmd==ADM_SW_IOCTL_MACENTRY_GET_INIT) - if (cmd==ADM_SW_IOCTL_MACENTRY_ADD) control[5]=0x07;//create a new address - else if (cmd==ADM_SW_IOCTL_MACENTRY_DEL) control[5]=0x01f;//erased an existed address - else if ((cmd==ADM_SW_IOCTL_MACENTRY_GET_INIT)||(cmd==ADM_SW_IOCTL_MACENTRY_GET_MORE)) - control[5]=0x02c;//search by the mac address field - - val=0x8000;//busy ,status5[15] - while(val&0x8000){ //check busy ? - ifx_sw_read(0x125, &val); - } - ifx_sw_write(0x11a,control[0]); - ifx_sw_write(0x11b,control[1]); - ifx_sw_write(0x11c,control[2]); - ifx_sw_write(0x11d,control[3]); - ifx_sw_write(0x11e,control[4]); - ifx_sw_write(0x11f,control[5]); - val=0x8000;//busy ,status5[15] - while(val&0x8000){ //check busy ? - ifx_sw_read(0x125, &val); - } - val=((val&0x7000)>>12);//result ,status5[14:12] - mMACENTRY->result=val; - - if (!val) { - printk(" Command OK!! \n"); - if ((cmd==ADM_SW_IOCTL_MACENTRY_GET_INIT)||(cmd==ADM_SW_IOCTL_MACENTRY_GET_MORE)) { - ifx_sw_read(0x120,&(status[0])); - ifx_sw_read(0x121,&(status[1])); - ifx_sw_read(0x122,&(status[2])); - ifx_sw_read(0x123,&(status[3])); - ifx_sw_read(0x124,&(status[4])); - ifx_sw_read(0x125,&(status[5])); - - - mMACENTRY->mac_addr[0]=(status[0]&0x00ff) ; - mMACENTRY->mac_addr[1]=(status[0]&0xff00)>>8 ; - mMACENTRY->mac_addr[2]=(status[1]&0x00ff) ; - mMACENTRY->mac_addr[3]=(status[1]&0xff00)>>8 ; - mMACENTRY->mac_addr[4]=(status[2]&0x00ff) ; - mMACENTRY->mac_addr[5]=(status[2]&0xff00)>>8 ; - mMACENTRY->fid=(status[3]&0xf); - mMACENTRY->portmap=((status[3]>>4)&0x3f); - if (status[5]&0x2) {//static info_ctrl //status5[1]???? - mMACENTRY->ctrl.info_ctrl=(status[4]&0x00ff); - mMACENTRY->info_type=1; - } - else {//not static age_timer - mMACENTRY->ctrl.age_timer=(status[4]&0x00ff); - mMACENTRY->info_type=0; - } -//status5[13]???? mMACENTRY->occupy=(status[5]&0x02)>>1;//status5[1] - mMACENTRY->occupy=(status[5]&0x02000)>>13;//status5[13] ??? - mMACENTRY->bad=(status[5]&0x04)>>2;//status5[2] - }//if ((cmd==ADM_SW_IOCTL_MACENTRY_GET_INIT)||(cmd==ADM_SW_IOCTL_MACENTRY_GET_MORE)) - - } - else if (val==0x001) - printk(" All Entry Used!! \n"); - else if (val==0x002) - printk(" Entry Not Found!! \n"); - else if (val==0x003) - printk(" Try Next Entry!! \n"); - else if (val==0x005) - printk(" Command Error!! \n"); - else - printk(" UnKnown Error!! \n"); - - // printk ("adm_process_mac_table_request: Exit\n"); - return 0; -} - -/* Santosh: End of function for MAC ENTRY ADD/DEL*/ -struct file_operations adm_ops = -{ - read: adm_read, - write: adm_write, - open: adm_open, - release: adm_release, - ioctl: adm_ioctl -}; - -int adm_proc(char *buf, char **start, off_t offset, int count, int *eof, void *data) -{ - int len = 0; - - len += sprintf(buf+len, " ************ Registers ************ \n"); - *eof = 1; - return len; -} - -int __init init_adm6996_module(void) -{ - unsigned int val = 000; - unsigned int val1 = 000; - - printk("Loading ADM6996 driver... \n"); - - /* if running on adm5120 */ - /* set GPIO 0~2 as adm6996 control pins */ - //outl(0x003f3f00, 0x12000028); - /* enable switch port 5 (MII) as RMII mode (5120MAC <-> 6996MAC) */ - //outl(0x18a, 0x12000030); - /* group adm5120 port 1 ~ 5 as VLAN0, port 5 & 6(CPU) as VLAN1 */ - //outl(0x417e, 0x12000040); - /* end adm5120 fixup */ -#ifdef ADM6996_MDC_MDIO_MODE //smi mode //000001.joelin - register_chrdev(69, "adm6996", &adm_ops); - AMAZON_SW_REG(AMAZON_SW_MDIO_CFG) = 0x27be; - AMAZON_SW_REG(AMAZON_SW_EPHY) = 0xfc; - adm6996_mode=adm6996i; - ifx_sw_read(0xa0, &val); - ifx_sw_read(0xa1, &val1); - val=((val1&0x0f)<<16)|val; - printk ("\nADM6996 SMI Mode-"); - printk ("Chip ID:%5x \n ", val); -#else //000001.joelin - - AMAZON_SW_REG(AMAZON_SW_MDIO_CFG) = 0x2c50; - AMAZON_SW_REG(AMAZON_SW_EPHY) = 0xff; - - AMAZON_SW_REG(AMAZON_GPIO_P1_ALTSEL0) &= ~(GPIO_MDIO|GPIO_MDCS|GPIO_MDC); - AMAZON_SW_REG(AMAZON_GPIO_P1_ALTSEL1) &= ~(GPIO_MDIO|GPIO_MDCS|GPIO_MDC); - AMAZON_SW_REG(AMAZON_GPIO_P1_OD) |= (GPIO_MDIO|GPIO_MDCS|GPIO_MDC); - - ifx_gpio_init(); - register_chrdev(69, "adm6996", &adm_ops); - mdelay(100); - - /* create proc entries */ - // create_proc_read_entry("admide", 0, NULL, admide_proc, NULL); - -//joelin adm6996i support start - adm6996_mode=adm6996i; - ifx_sw_read(0xa0, &val); - adm6996_mode=adm6996l; - ifx_sw_read(0x200, &val1); -// printk ("\n %0x \n",val1); - if ((val&0xfff0)==0x1020) { - printk ("\n ADM6996I .. \n"); - adm6996_mode=adm6996i; - } - else if ((val1&0xffffff00)==0x71000) {//71010 or 71020 - printk ("\n ADM6996LC .. \n"); - adm6996_mode=adm6996lc; - } - else { - printk ("\n ADM6996L .. \n"); - adm6996_mode=adm6996l; - } -#endif //ADM6996_MDC_MDIO_MODE //smi mode //000001.joelin - - if ((adm6996_mode==adm6996lc)||(adm6996_mode==adm6996i)){ -#if 0 /* removed by MarsLin */ - ifx_sw_write(0x29,0xc000); - ifx_sw_write(0x30,0x0985); -#else - ifx_sw_read(0xa0, &val); - if (val == 0x1021) // for both 6996LC and 6996I, only AB version need the patch - ifx_sw_write(0x29, 0x9000); - ifx_sw_write(0x30,0x0985); -#endif - } -//joelin adm6996i support end - return 0; -} - -void __exit cleanup_adm6996_module(void) -{ - printk("Free ADM device driver... \n"); - - unregister_chrdev(69, "adm6996"); - - /* remove proc entries */ - // remove_proc_entry("admide", NULL); -} - -/* MarsLin, add start */ -#if defined(CONFIG_IFX_NFEXT_AMAZON_SWITCH_PHYPORT) || defined(CONFIG_IFX_NFEXT_AMAZON_SWITCH_PHYPORT_MODULE) - #define SET_BIT(reg, mask) reg |= (mask) - #define CLEAR_BIT(reg, mask) reg &= (~mask) - static int ifx_hw_reset(void) - { - CLEAR_BIT((*AMAZON_GPIO_P0_ALTSEL0),0x2000); - CLEAR_BIT((*AMAZON_GPIO_P0_ALTSEL1),0x2000); - SET_BIT((*AMAZON_GPIO_P0_OD),0x2000); - SET_BIT((*AMAZON_GPIO_P0_DIR), 0x2000); - CLEAR_BIT((*AMAZON_GPIO_P0_OUT), 0x2000); - mdelay(500); - SET_BIT((*AMAZON_GPIO_P0_OUT), 0x2000); - cleanup_adm6996_module(); - return init_adm6996_module(); - } - int (*adm6996_hw_reset)(void) = ifx_hw_reset; - EXPORT_SYMBOL(adm6996_hw_reset); - EXPORT_SYMBOL(adm6996_mode); - int (*adm6996_sw_read)(unsigned int addr, unsigned int *data) = ifx_sw_read; - EXPORT_SYMBOL(adm6996_sw_read); - int (*adm6996_sw_write)(unsigned int addr, unsigned int data) = ifx_sw_write; - EXPORT_SYMBOL(adm6996_sw_write); -#endif -/* MarsLin, add end */ - -/* Santosh: for IGMP proxy/snooping, Begin */ -EXPORT_SYMBOL (adm_process_mac_table_request); -EXPORT_SYMBOL (adm_process_protocol_filter_request); -/* Santosh: for IGMP proxy/snooping, End */ - -MODULE_DESCRIPTION("ADMtek 6996 Driver"); -MODULE_AUTHOR("Joe Lin <joe.lin@infineon.com>"); -MODULE_LICENSE("GPL"); - -module_init(init_adm6996_module); -module_exit(cleanup_adm6996_module); - |