diff options
Diffstat (limited to 'package/mac80211/patches/001-disable_drivers.patch')
| -rw-r--r-- | package/mac80211/patches/001-disable_drivers.patch | 147 |
1 files changed, 0 insertions, 147 deletions
diff --git a/package/mac80211/patches/001-disable_drivers.patch b/package/mac80211/patches/001-disable_drivers.patch deleted file mode 100644 index ccf040915..000000000 --- a/package/mac80211/patches/001-disable_drivers.patch +++ /dev/null @@ -1,147 +0,0 @@ -diff -urN compat-wireless-2008-08-06/config.mk compat-wireless-2008-08-06.new/config.mk ---- compat-wireless-2008-08-06/config.mk 2008-07-18 06:11:03.000000000 +0200 -+++ compat-wireless-2008-08-06.new/config.mk 2008-08-20 17:30:13.000000000 +0200 -@@ -72,70 +72,6 @@ - CONFIG_ATH5K=m - CONFIG_ATH5K_DEBUG=n - --# Required for older kernels which still use this flag. --CONFIG_IWLWIFI=m -- --CONFIG_IWLCORE=m --CONFIG_IWL3945=m --CONFIG_IWL4965=m --CONFIG_IWL4965_HT=y --CONFIG_B43=m --# B43 uses PCMCIA only for Compact Flash. The Cardbus cards uses PCI --# Example, bcm4318: --# http://www.multicap.biz/wireless-lan/indoor-wlan-hardware/sdc-cf10g-80211g-compact-flash-module --CONFIG_B43_PCMCIA=y --CONFIG_B43_DMA=y --CONFIG_B43_PIO=y --# B43_PIO selects SSB_BLOCKIO --CONFIG_SSB_BLOCKIO=y --CONFIG_B43_DMA_AND_PIO_MODE=y --CONFIG_B43_PCI_AUTOSELECT=y --CONFIG_B43_PCICORE_AUTOSELECT=y --#CONFIG_B43_RFKILL=n --CONFIG_B43_LEDS=y --# CONFIG_B43_DEBUG is not set -- --CONFIG_B43LEGACY=m --CONFIG_B43LEGACY_PCI_AUTOSELECT=y --CONFIG_B43LEGACY_PCICORE_AUTOSELECT=y --CONFIG_B43LEGACY_DMA=y --CONFIG_B43LEGACY_PIO=y --CONFIG_B43LEGACY_DMA_AND_PIO_MODE=y -- --# The Intel ipws --CONFIG_IPW2100=m --CONFIG_IPW2100_MONITOR=y --CONFIG_IPW2200=m --CONFIG_IPW2200_MONITOR=y --CONFIG_IPW2200_RADIOTAP=y --CONFIG_IPW2200_PROMISCUOUS=y --# The above enables use a second interface prefixed 'rtap'. --# Example usage: --# --# % modprobe ipw2200 rtap_iface=1 --# % ifconfig rtap0 up --# % tethereal -i rtap0 --# --# If you do not specify 'rtap_iface=1' as a module parameter then --# the rtap interface will not be created and you will need to turn --# it on via sysfs: --# --# % echo 1 > /sys/bus/pci/drivers/ipw2200/*/rtap_iface --CONFIG_IPW2200_QOS=y -- --NEED_IEEE80211=y -- --CONFIG_P54_PCI=m -- --CONFIG_SSB_PCIHOST_POSSIBLE=y --CONFIG_SSB_PCIHOST=y --CONFIG_SSB_DRIVER_PCICORE_POSSIBLE=y --CONFIG_SSB_DRIVER_PCICORE=y --CONFIG_SSB_B43_PCI_BRIDGE=y -- --CONFIG_RTL8180=m --CONFIG_ADM8211=m -- - CONFIG_RT2X00_LIB_PCI=m - CONFIG_RT2400PCI=m - CONFIG_RT2500PCI=m -@@ -159,32 +95,6 @@ - ifneq ($(CONFIG_USB),) - CONFIG_ZD1211RW=m - --# support for USB Wireless devices using Atmel at76c503, --# at76c505 or at76c505a chips. --CONFIG_USB_ATMEL=m -- --# Stuff here things which depend on kernel versions for USB --ifeq ($(shell test -e $(KLIB_BUILD)/Makefile && echo yes),yes) --KERNEL_SUBLEVEL = $(shell $(MAKE) -C $(KLIB_BUILD) kernelversion | sed -n 's/^2\.6\.\([0-9]\+\).*/\1/p') --ifeq ($(shell test $(KERNEL_SUBLEVEL) -gt 21 && echo yes),yes) -- --# Sorry, rndis_wlan uses cancel_work_sync which is new and can't be done in compat... -- --# Wireless RNDIS USB support (RTL8185 802.11g) A-Link WL54PC --# All of these devices are based on Broadcom 4320 chip which --# is only wireless RNDIS chip known to date. --# Note: this depends on CONFIG_USB_NET_RNDIS_HOST and CONFIG_USB_NET_CDCETHER --# it also requires new RNDIS_HOST and CDC_ETHER modules which we add --CONFIG_USB_NET_RNDIS_HOST=m --CONFIG_USB_NET_RNDIS_WLAN=m --CONFIG_USB_NET_CDCETHER=m -- --endif --endif -- --CONFIG_P54_USB=m --CONFIG_RTL8187=m -- - # RT2500USB does not require firmware - CONFIG_RT2500USB=m - CONFIG_RT2X00_LIB_USB=m -@@ -209,39 +119,6 @@ - CONFIG_RT2X00_LIB_FIRMWARE=y - endif - --# p54 --CONFIG_P54_COMMON=m -- --# Sonics Silicon Backplane --CONFIG_SSB_POSSIBLE=y --CONFIG_SSB=m --CONFIG_SSB_SPROM=y -- --ifneq ($(CONFIG_PCMCIA),) --CONFIG_SSB_PCMCIAHOST=y --endif -- --# These two are for mips --CONFIG_SSB_DRIVER_MIPS=n --CONFIG_SSB_PCICORE_HOSTMODE=n --# CONFIG_SSB_DEBUG is not set --# CONFIG_SSB_DRIVER_EXTIF=y -- --ifneq ($(CONFIG_USB),) --CONFIG_LIBERTAS_USB=m --NEED_LIBERTAS=y --endif --ifneq ($(CONFIG_PCMCIA),) --CONFIG_LIBERTAS_CS=m --NEED_LIBERTAS=y --endif --ifeq ($(NEED_LIBERTAS),y) --CONFIG_LIBERTAS=m --# Libertas uses the old stack but not fully, it will soon --# be cleaned. --NEED_IEEE80211=y --endif -- - ifeq ($(NEED_IEEE80211),y) - # Old ieee80211 "stack" - # Note: old softmac is scheduled for removal so we |