diff options
Diffstat (limited to 'package/boot/uboot-kirkwood/files/board/iomega/iconnect/iconnect.c')
| -rw-r--r-- | package/boot/uboot-kirkwood/files/board/iomega/iconnect/iconnect.c | 141 |
1 files changed, 0 insertions, 141 deletions
diff --git a/package/boot/uboot-kirkwood/files/board/iomega/iconnect/iconnect.c b/package/boot/uboot-kirkwood/files/board/iomega/iconnect/iconnect.c deleted file mode 100644 index 34ddadf8a..000000000 --- a/package/boot/uboot-kirkwood/files/board/iomega/iconnect/iconnect.c +++ /dev/null @@ -1,141 +0,0 @@ -/* - * Copyright (C) 2009-2012 - * Wojciech Dubowik <wojciech.dubowik@neratec.com> - * Luka Perkov <uboot@lukaperkov.net> - * - * See file CREDITS for list of people who contributed to this - * project. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of - * the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program. If not, see <http://www.gnu.org/licenses/>. - */ - -#include <common.h> -#include <miiphy.h> -#include <asm/arch/cpu.h> -#include <asm/arch/kirkwood.h> -#include <asm/arch/mpp.h> -#include "iconnect.h" - -DECLARE_GLOBAL_DATA_PTR; - -int board_early_init_f(void) -{ - /* - * default gpio configuration - * There are maximum 64 gpios controlled through 2 sets of registers - * the below configuration configures mainly initial LED status - */ - kw_config_gpio(ICONNECT_OE_VAL_LOW, - ICONNECT_OE_VAL_HIGH, - ICONNECT_OE_LOW, ICONNECT_OE_HIGH); - - /* Multi-Purpose Pins Functionality configuration */ - u32 kwmpp_config[] = { - MPP0_NF_IO2, - MPP1_NF_IO3, - MPP2_NF_IO4, - MPP3_NF_IO5, - MPP4_NF_IO6, - MPP5_NF_IO7, - MPP6_SYSRST_OUTn, - MPP7_GPO, - MPP8_TW_SDA, - MPP9_TW_SCK, - MPP10_UART0_TXD, - MPP11_UART0_RXD, - MPP12_GPO, - MPP13_SD_CMD, - MPP14_SD_D0, - MPP15_SD_D1, - MPP16_SD_D2, - MPP17_SD_D3, - MPP18_NF_IO0, - MPP19_NF_IO1, - MPP20_GE1_0, - MPP21_GE1_1, - MPP22_GE1_2, - MPP23_GE1_3, - MPP24_GE1_4, - MPP25_GE1_5, - MPP26_GE1_6, - MPP27_GE1_7, - MPP28_GPIO, - MPP29_GPIO, - MPP30_GE1_10, - MPP31_GE1_11, - MPP32_GE1_12, - MPP33_GE1_13, - MPP34_GE1_14, - MPP35_GPIO, - MPP36_AUDIO_SPDIFI, - MPP37_AUDIO_SPDIFO, - MPP38_GPIO, - MPP39_TDM_SPI_CS0, - MPP40_TDM_SPI_SCK, - MPP41_GPIO, - MPP42_GPIO, - MPP43_GPIO, - MPP44_GPIO, - MPP45_GPIO, - MPP46_GPIO, - MPP47_GPIO, - MPP48_GPIO, - MPP49_GPIO, - 0 - }; - kirkwood_mpp_conf(kwmpp_config); - return 0; -} - -int board_init(void) -{ - /* Boot parameters address */ - gd->bd->bi_boot_params = kw_sdram_bar(0) + 0x100; - - return 0; -} - -#ifdef CONFIG_RESET_PHY_R -/* Configure and initialize PHY */ -void reset_phy(void) -{ - u16 reg; - u16 devadr; - char *name = "egiga0"; - - if (miiphy_set_current_dev(name)) - return; - - /* command to read PHY dev address */ - if (miiphy_read(name, 0xEE, 0xEE, (u16 *) &devadr)) { - printf("Err..(%s) could not read PHY dev address\n", __func__); - return; - } - - /* - * Enable RGMII delay on Tx and Rx for CPU port - * Ref: sec 4.7.2 of chip datasheet - */ - miiphy_write(name, devadr, MV88E1116_PGADR_REG, 2); - miiphy_read(name, devadr, MV88E1116_MAC_CTRL_REG, ®); - reg |= (MV88E1116_RGMII_RXTM_CTRL | MV88E1116_RGMII_TXTM_CTRL); - miiphy_write(name, devadr, MV88E1116_MAC_CTRL_REG, reg); - miiphy_write(name, devadr, MV88E1116_PGADR_REG, 0); - - /* reset the phy */ - miiphy_reset(name, devadr); - - debug("88E1116 Initialized on %s\n", name); -} -#endif /* CONFIG_RESET_PHY_R */ |