[pxa]: upgrade to 2.6.32.7, switch to squashfs, remove broken flag

git-svn-id: svn://svn.openwrt.org/openwrt/trunk@19562 3c298f89-4303-0410-b956-a3cf2f4a3e73

1 files changed, 0 insertions, 371 deletions

diff --git a/target/linux/pxa/patches-2.6.21/044-smc911x-fixup.patch b/target/linux/pxa/patches-2.6.21/044-smc911x-fixup.patch
deleted file mode 100644
index 7ddfd5fda..000000000
--- a/target/linux/pxa/patches-2.6.21/044-smc911x-fixup.patch
+++ /dev/null
@@ -1,371 +0,0 @@
---- a/drivers/net/smc911x.c
-+++ b/drivers/net/smc911x.c
-@@ -76,6 +76,7 @@ static const char version[] =
- #include <linux/etherdevice.h>
- #include <linux/skbuff.h>
- 
-+#include <linux/irq.h>
- #include <asm/io.h>
- #include <asm/irq.h>
- 
-@@ -303,14 +304,14 @@ static void smc911x_reset(struct net_dev
- 	SMC_SET_AFC_CFG(lp->afc_cfg);
- 
- 
--	/* Set to LED outputs */
--	SMC_SET_GPIO_CFG(0x70070000);
-+	/* Set to LED outputs and configure EEPROM pins as GP outputs */
-+	SMC_SET_GPIO_CFG(GPIO_CFG_LED1_EN_ | GPIO_CFG_LED2_EN_ | 1 << 20);
- 
- 	/*
--	 * Deassert IRQ for 1*10us for edge type interrupts
-+	 * Deassert IRQ for 22*10us for edge type interrupts
- 	 * and drive IRQ pin push-pull
- 	 */
--	SMC_SET_IRQ_CFG( (1 << 24) | INT_CFG_IRQ_EN_ | INT_CFG_IRQ_TYPE_ );
-+	SMC_SET_IRQ_CFG( (22 << 24) | INT_CFG_IRQ_EN_ | INT_CFG_IRQ_TYPE_ );
- 
- 	/* clear anything saved */
- 	if (lp->pending_tx_skb != NULL) {
-@@ -413,7 +414,7 @@ static inline void smc911x_drop_pkt(stru
- 	if (fifo_count <= 4) {
- 		/* Manually dump the packet data */
- 		while (fifo_count--)
--			SMC_GET_RX_FIFO();
-+			(void)SMC_GET_RX_FIFO();
- 	} else	 {
- 		/* Fast forward through the bad packet */
- 		SMC_SET_RX_DP_CTRL(RX_DP_CTRL_FFWD_BUSY_);
-@@ -900,6 +901,7 @@ static void smc911x_phy_powerdown(struct
- 	unsigned long ioaddr = dev->base_addr;
- 	unsigned int bmcr;
- 
-+	DBG(SMC_DEBUG_FUNC, "%s: --> %s\n", dev->name, __FUNCTION__);
- 	/* Enter Link Disable state */
- 	SMC_GET_PHY_BMCR(phy, bmcr);
- 	bmcr |= BMCR_PDOWN;
-@@ -925,6 +927,7 @@ static void smc911x_phy_check_media(stru
- 
- 	if (mii_check_media(&lp->mii, netif_msg_link(lp), init)) {
- 		/* duplex state has changed */
-+		DBG(SMC_DEBUG_MISC, "%s: duplex state has changed\n", dev->name);
- 		SMC_GET_PHY_BMCR(phyaddr, bmcr);
- 		SMC_GET_MAC_CR(cr);
- 		if (lp->mii.full_duplex) {
-@@ -960,6 +963,7 @@ static void smc911x_phy_configure(struct
- 	int my_phy_caps; /* My PHY capabilities */
- 	int my_ad_caps; /* My Advertised capabilities */
- 	int status;
-+	int bmcr;
- 	unsigned long flags;
- 
- 	DBG(SMC_DEBUG_FUNC, "%s: --> %s()\n", dev->name, __FUNCTION__);
-@@ -1033,9 +1037,12 @@ static void smc911x_phy_configure(struct
- 
- 	DBG(SMC_DEBUG_MISC, "%s: phy caps=0x%04x\n", dev->name, my_phy_caps);
- 	DBG(SMC_DEBUG_MISC, "%s: phy advertised caps=0x%04x\n", dev->name, my_ad_caps);
-+	DBG(SMC_DEBUG_MISC, "%s: phy advertised readback caps=0x%04x\n", dev->name, status);
- 
- 	/* Restart auto-negotiation process in order to advertise my caps */
--	SMC_SET_PHY_BMCR(phyaddr, BMCR_ANENABLE | BMCR_ANRESTART);
-+	SMC_GET_PHY_BMCR(phyaddr, bmcr);
-+	bmcr |= BMCR_ANENABLE | BMCR_ANRESTART;
-+	SMC_SET_PHY_BMCR(phyaddr, bmcr);
- 
- 	smc911x_phy_check_media(dev, 1);
- 
-@@ -1888,6 +1895,39 @@ static int __init smc911x_findirq(unsign
- 	return probe_irq_off(cookie);
- }
- 
-+static inline unsigned int is_gumstix_oui(u8 *addr)
-+{
-+	return (addr[0] == 0x00 && addr[1] == 0x15 && addr[2] == 0xC9);
-+}
-+
-+/**
-+ * gen_serial_ether_addr - Generate software assigned Ethernet address
-+ * based on the system_serial number
-+ * @addr: Pointer to a six-byte array containing the Ethernet address
-+ *
-+ * Generate an Ethernet address (MAC) that is not multicast
-+ * and has the local assigned bit set, keyed on the system_serial
-+ */
-+static inline void gen_serial_ether_addr(u8 *addr)
-+{
-+	static u8 ether_serial_digit = 0;
-+	addr [0] = system_serial_high >> 8;
-+	addr [1] = system_serial_high;
-+	addr [2] = system_serial_low >> 24;
-+	addr [3] = system_serial_low >> 16;
-+	addr [4] = system_serial_low >> 8;
-+	addr [5] = (system_serial_low & 0xc0) |	/* top bits are from system serial */
-+		(1 << 4) |			/* 2 bits identify interface type 1=ether, 2=usb, 3&4 undef */
-+		((ether_serial_digit++) & 0x0f);	/* 15 possible interfaces of each type */
-+
-+	if(!is_gumstix_oui(addr))
-+	{
-+		addr [0] &= 0xfe;		/* clear multicast bit */
-+		addr [0] |= 0x02;		/* set local assignment bit (IEEE802) */
-+	}
-+}
-+
-+
- /*
-  * Function: smc911x_probe(unsigned long ioaddr)
-  *
-@@ -2116,15 +2156,13 @@ static int __init smc911x_probe(struct n
- #endif
- 		printk("\n");
- 		if (!is_valid_ether_addr(dev->dev_addr)) {
--			printk("%s: Invalid ethernet MAC address. Please "
--					"set using ifconfig\n", dev->name);
--		} else {
--			/* Print the Ethernet address */
--			printk("%s: Ethernet addr: ", dev->name);
--			for (i = 0; i < 5; i++)
--				printk("%2.2x:", dev->dev_addr[i]);
--			printk("%2.2x\n", dev->dev_addr[5]);
-+			gen_serial_ether_addr(dev->dev_addr);
- 		}
-+		/* Print the Ethernet address */
-+		printk("%s: Ethernet addr: ", dev->name);
-+		for (i = 0; i < 5; i++)
-+			printk("%2.2x:", dev->dev_addr[i]);
-+		printk("%2.2x\n", dev->dev_addr[5]);
- 
- 		if (lp->phy_type == 0) {
- 			PRINTK("%s: No PHY found\n", dev->name);
-@@ -2300,8 +2338,15 @@ static struct platform_driver smc911x_dr
- 	},
- };
- 
-+#ifdef CONFIG_ARCH_GUMSTIX
-+extern void gumstix_smc911x_load(void);
-+#endif
-+
- static int __init smc911x_init(void)
- {
-+#ifdef CONFIG_ARCH_GUMSTIX
-+	gumstix_smc911x_load();
-+#endif
- 	return platform_driver_register(&smc911x_driver);
- }
- 
---- /dev/null
-+++ b/drivers/net/gumstix-smc911x.c
-@@ -0,0 +1,148 @@
-+/*
-+ *  Gumstix SMC911x chip intialization driver
-+ *
-+ *  Author:     Craig Hughes
-+ *  Created:    December 9, 2004
-+ *  Copyright:  (C) 2004 Craig Hughes
-+ *
-+ * This program is free software; you can redistribute it and/or modify
-+ * it under the terms of the GNU General Public License as published by
-+ * the Free Software Foundation; either version 2 of the License, or
-+ * (at your option) any later version.
-+ *
-+ */
-+
-+#include <linux/module.h>
-+#include <linux/ioport.h>
-+#include <linux/device.h>
-+#include <linux/platform_device.h>
-+#include <linux/delay.h>
-+
-+#include <asm/hardware.h>
-+#include <asm/arch/pxa-regs.h>
-+#include <asm/delay.h>
-+
-+#include <asm/arch/gumstix.h>
-+
-+#define SMC_DEBUG               9
-+#include <asm/io.h>
-+#include "smc911x.h"
-+
-+static struct resource gumstix_smc911x0_resources[] = {
-+	[0] = {
-+		.name	= "smc911x-regs",
-+		.start  = PXA_CS1_PHYS,
-+		.end    = PXA_CS1_PHYS + 0x000fffff,
-+		.flags  = IORESOURCE_MEM,
-+	},
-+	[1] = {
-+		.start  = GUMSTIX_ETH0_IRQ,
-+		.end    = GUMSTIX_ETH0_IRQ,
-+		.flags  = IORESOURCE_IRQ,
-+	},
-+};
-+
-+static struct resource gumstix_smc911x1_resources[] = {
-+	[0] = {
-+		.name	= "smc911x-regs",
-+		.start	= PXA_CS2_PHYS,
-+		.end	= PXA_CS2_PHYS + 0x000fffff,
-+		.flags	= IORESOURCE_MEM,
-+	},
-+	[1] = {
-+		.start	= GUMSTIX_ETH1_IRQ,
-+		.end	= GUMSTIX_ETH1_IRQ,
-+		.flags	= IORESOURCE_IRQ,
-+	},
-+};
-+
-+static struct platform_device gumstix_smc911x0_device = {
-+	.name           = "smc911x",
-+	.id             = 0,
-+	.num_resources  = ARRAY_SIZE(gumstix_smc911x0_resources),
-+	.resource       = gumstix_smc911x0_resources,
-+};
-+
-+static struct platform_device gumstix_smc911x1_device = {
-+	.name           = "smc911x",
-+	.id             = 1,
-+	.num_resources  = ARRAY_SIZE(gumstix_smc911x1_resources),
-+	.resource       = gumstix_smc911x1_resources,
-+};
-+
-+static struct platform_device *smc911x_devices[] = {
-+	&gumstix_smc911x0_device,
-+	&gumstix_smc911x1_device,
-+};
-+
-+/* First we're going to test if there's a 2nd SMC911x, and if not, then we'll free up those resources and the GPIO lines
-+ * that it would otherwise use.  We have no choice but to probe by doing:
-+ * Set nCS2 to CS2 mode
-+ * Set the reset line to GPIO out mode, and pull it high, then drop it low (to trigger reset)
-+ * Read from the memory space to check for the sentinel sequence identifying a likely SMC911x device
-+ */
-+int __init gumstix_smc911x_init(void)
-+{
-+	unsigned int val, num_devices=ARRAY_SIZE(smc911x_devices);
-+	void *ioaddr;
-+
-+	/* Set up nPWE */
-+	pxa_gpio_mode(GPIO49_nPWE_MD);
-+
-+	pxa_gpio_mode(GPIO78_nCS_2_MD);
-+	// If either if statement fails, then we'll drop out and turn_off_eth1,
-+	// if both succeed, then we'll skip that and just proceed with 2 cards
-+	if(request_mem_region(gumstix_smc911x1_resources[1].start, SMC911X_IO_EXTENT, "smc911x probe"))
-+	{
-+		ioaddr = ioremap(gumstix_smc911x1_resources[1].start, SMC911X_IO_EXTENT);
-+		val = SMC_GET_PN();
-+		iounmap(ioaddr);
-+		release_mem_region(gumstix_smc911x1_resources[1].start, SMC911X_IO_EXTENT);
-+		if (CHIP_9115 == val ||
-+			CHIP_9116 == val ||
-+			CHIP_9117 == val ||
-+			CHIP_9118 == val ) {
-+			goto proceed;
-+		}
-+	}
-+
-+turn_off_eth1:
-+	// This is apparently not an SMC911x
-+	// So, let's decrement the number of devices to request, and reset the GPIO lines to GPIO IN mode
-+	num_devices--;
-+	smc911x_devices[1] = NULL;
-+	pxa_gpio_mode(78 | GPIO_IN);
-+	
-+proceed:
-+	pxa_gpio_mode(GPIO15_nCS_1_MD);
-+
-+	if(smc911x_devices[1]) pxa_gpio_mode(GPIO_GUMSTIX_ETH1_RST_MD);
-+	pxa_gpio_mode(GPIO_GUMSTIX_ETH0_RST_MD);
-+
-+	if(smc911x_devices[1]) GPCR(GPIO_GUMSTIX_ETH1_RST) = GPIO_bit(GPIO_GUMSTIX_ETH1_RST);
-+	GPCR(GPIO_GUMSTIX_ETH0_RST) = GPIO_bit(GPIO_GUMSTIX_ETH0_RST);
-+	msleep(500); // Hold RESET for at least 200µ
-+
-+	if(smc911x_devices[1]) GPSR(GPIO_GUMSTIX_ETH1_RST) = GPIO_bit(GPIO_GUMSTIX_ETH1_RST);
-+	GPSR(GPIO_GUMSTIX_ETH0_RST) = GPIO_bit(GPIO_GUMSTIX_ETH0_RST);
-+	msleep(50);
-+
-+	return platform_add_devices(smc911x_devices, num_devices);
-+}
-+
-+void __exit gumstix_smc911x_exit(void)
-+{
-+	if(smc911x_devices[1] != NULL) platform_device_unregister(&gumstix_smc911x1_device);
-+	platform_device_unregister(&gumstix_smc911x0_device);
-+}
-+
-+void gumstix_smc911x_load(void) {}
-+EXPORT_SYMBOL(gumstix_smc911x_load);
-+
-+module_init(gumstix_smc911x_init);
-+module_exit(gumstix_smc911x_exit);
-+
-+MODULE_LICENSE("GPL");
-+MODULE_AUTHOR("Craig Hughes <craig@gumstix.com>");
-+MODULE_DESCRIPTION("Gumstix board SMC911x chip initialization driver");
-+MODULE_VERSION("1:0.1");
---- a/drivers/net/Kconfig
-+++ b/drivers/net/Kconfig
-@@ -1020,6 +1020,13 @@ config SMC911X
- 	  called smc911x.  If you want to compile it as a module, say M 
- 	  here and read <file:Documentation/modules.txt>
- 
-+config SMC911X_GUMSTIX
-+	tristate
-+	default m if SMC911X=m
-+	default y if SMC911X=y
-+	depends on SMC911X && ARCH_GUMSTIX
-+
-+
- config NET_VENDOR_RACAL
- 	bool "Racal-Interlan (Micom) NI cards"
- 	depends on NET_ETHERNET && ISA
---- a/drivers/net/Makefile
-+++ b/drivers/net/Makefile
-@@ -202,6 +202,7 @@ obj-$(CONFIG_PASEMI_MAC) += pasemi_mac.o
- obj-$(CONFIG_MACB) += macb.o
- 
- obj-$(CONFIG_SMC91X_GUMSTIX) += gumstix-smc91x.o
-+obj-$(CONFIG_SMC911X_GUMSTIX) += gumstix-smc911x.o
- obj-$(CONFIG_ARM) += arm/
- obj-$(CONFIG_DEV_APPLETALK) += appletalk/
- obj-$(CONFIG_TR) += tokenring/
---- a/include/asm-arm/arch-pxa/gumstix.h
-+++ b/include/asm-arm/arch-pxa/gumstix.h
-@@ -52,7 +52,7 @@
- #define GPIO_GUMSTIX_ETH0_RST		80
- #define GPIO_GUMSTIX_ETH0		36
- #else
--#define GPIO_GUMSTIX_ETH0_RST		32
-+#define GPIO_GUMSTIX_ETH0_RST		107
- #define GPIO_GUMSTIX_ETH0		99
- #endif
- #define GPIO_GUMSTIX_ETH1_RST		52
---- a/drivers/net/smc911x.h
-+++ b/drivers/net/smc911x.h
-@@ -33,7 +33,9 @@
-  * Use the DMA feature on PXA chips
-  */
- #ifdef CONFIG_ARCH_PXA
-+#if !defined( CONFIG_SMC911X_GUMSTIX ) && !defined( CONFIG_SMC911X_GUMSTIX_MODULE )
-   #define SMC_USE_PXA_DMA	1
-+#endif
-   #define SMC_USE_16BIT		0
-   #define SMC_USE_32BIT		1
- #endif
-@@ -46,13 +48,13 @@
- #if	SMC_USE_16BIT
- #define SMC_inb(a, r)			 readb((a) + (r))
- #define SMC_inw(a, r)			 readw((a) + (r))
--#define SMC_inl(a, r)			 ((SMC_inw(a, r) & 0xFFFF)+(SMC_inw(a+2, r)<<16))
-+#define SMC_inl(a, r)			 ((SMC_inw(a, r) & 0xFFFF)+(SMC_inw((a)+2, r)<<16))
- #define SMC_outb(v, a, r)		 writeb(v, (a) + (r))
- #define SMC_outw(v, a, r)		 writew(v, (a) + (r))
- #define SMC_outl(v, a, r) 			 \
- 	do{					 \
--		 writel(v & 0xFFFF, (a) + (r));	 \
--		 writel(v >> 16, (a) + (r) + 2); \
-+		 writel((v) & 0xFFFF, (a) + (r));	 \
-+		 writel((v) >> 16, (a) + (r) + 2); \
- 	 } while (0)
- #define SMC_insl(a, r, p, l)	 readsw((short*)((a) + (r)), p, l*2)
- #define SMC_outsl(a, r, p, l)	 writesw((short*)((a) + (r)), p, l*2)