generic: nuke 2.6.33 specific stuff, is not used by any platform

git-svn-id: svn://svn.openwrt.org/openwrt/trunk@24644 3c298f89-4303-0410-b956-a3cf2f4a3e73

1 files changed, 0 insertions, 533 deletions

diff --git a/target/linux/generic/patches-2.6.33/975-ssb_update.patch b/target/linux/generic/patches-2.6.33/975-ssb_update.patch
deleted file mode 100644
index e994a8a50..000000000
--- a/target/linux/generic/patches-2.6.33/975-ssb_update.patch
+++ /dev/null
@@ -1,533 +0,0 @@
---- a/drivers/ssb/driver_chipcommon.c
-+++ b/drivers/ssb/driver_chipcommon.c
-@@ -373,6 +373,7 @@ u32 ssb_chipco_gpio_control(struct ssb_c
- {
- 	return chipco_write32_masked(cc, SSB_CHIPCO_GPIOCTL, mask, value);
- }
-+EXPORT_SYMBOL(ssb_chipco_gpio_control);
- 
- u32 ssb_chipco_gpio_intmask(struct ssb_chipcommon *cc, u32 mask, u32 value)
- {
---- a/drivers/ssb/driver_chipcommon_pmu.c
-+++ b/drivers/ssb/driver_chipcommon_pmu.c
-@@ -332,6 +332,12 @@ static void ssb_pmu_pll_init(struct ssb_
- 	case 0x5354:
- 		ssb_pmu0_pllinit_r0(cc, crystalfreq);
- 		break;
-+	case 0x4322:
-+		if (cc->pmu.rev == 2) {
-+			chipco_write32(cc, SSB_CHIPCO_PLLCTL_ADDR, 0x0000000A);
-+			chipco_write32(cc, SSB_CHIPCO_PLLCTL_DATA, 0x380005C0);
-+		}
-+		break;
- 	default:
- 		ssb_printk(KERN_ERR PFX
- 			   "ERROR: PLL init unknown for device %04X\n",
-@@ -417,6 +423,7 @@ static void ssb_pmu_resources_init(struc
- 
- 	switch (bus->chip_id) {
- 	case 0x4312:
-+	case 0x4322:
- 		/* We keep the default settings:
- 		 * min_msk = 0xCBB
- 		 * max_msk = 0x7FFFF
---- a/drivers/ssb/driver_mipscore.c
-+++ b/drivers/ssb/driver_mipscore.c
-@@ -270,7 +270,6 @@ void ssb_mipscore_init(struct ssb_mipsco
- 				set_irq(dev, irq++);
- 			}
- 			break;
--			/* fallthrough */
- 		case SSB_DEV_PCI:
- 		case SSB_DEV_ETHERNET:
- 		case SSB_DEV_ETHERNET_GBIT:
-@@ -281,6 +280,10 @@ void ssb_mipscore_init(struct ssb_mipsco
- 				set_irq(dev, irq++);
- 				break;
- 			}
-+			/* fallthrough */
-+		case SSB_DEV_EXTIF:
-+			set_irq(dev, 0);
-+			break;
- 		}
- 	}
- 	ssb_dprintk(KERN_INFO PFX "after irq reconfiguration\n");
---- a/drivers/ssb/driver_pcicore.c
-+++ b/drivers/ssb/driver_pcicore.c
-@@ -246,20 +246,12 @@ static struct pci_controller ssb_pcicore
- 	.pci_ops	= &ssb_pcicore_pciops,
- 	.io_resource	= &ssb_pcicore_io_resource,
- 	.mem_resource	= &ssb_pcicore_mem_resource,
--	.mem_offset	= 0x24000000,
- };
- 
--static u32 ssb_pcicore_pcibus_iobase = 0x100;
--static u32 ssb_pcicore_pcibus_membase = SSB_PCI_DMA;
--
- /* This function is called when doing a pci_enable_device().
-  * We must first check if the device is a device on the PCI-core bridge. */
- int ssb_pcicore_plat_dev_init(struct pci_dev *d)
- {
--	struct resource *res;
--	int pos, size;
--	u32 *base;
--
- 	if (d->bus->ops != &ssb_pcicore_pciops) {
- 		/* This is not a device on the PCI-core bridge. */
- 		return -ENODEV;
-@@ -268,27 +260,6 @@ int ssb_pcicore_plat_dev_init(struct pci
- 	ssb_printk(KERN_INFO "PCI: Fixing up device %s\n",
- 		   pci_name(d));
- 
--	/* Fix up resource bases */
--	for (pos = 0; pos < 6; pos++) {
--		res = &d->resource[pos];
--		if (res->flags & IORESOURCE_IO)
--			base = &ssb_pcicore_pcibus_iobase;
--		else
--			base = &ssb_pcicore_pcibus_membase;
--		res->flags |= IORESOURCE_PCI_FIXED;
--		if (res->end) {
--			size = res->end - res->start + 1;
--			if (*base & (size - 1))
--				*base = (*base + size) & ~(size - 1);
--			res->start = *base;
--			res->end = res->start + size - 1;
--			*base += size;
--			pci_write_config_dword(d, PCI_BASE_ADDRESS_0 + (pos << 2), res->start);
--		}
--		/* Fix up PCI bridge BAR0 only */
--		if (d->bus->number == 0 && PCI_SLOT(d->devfn) == 0)
--			break;
--	}
- 	/* Fix up interrupt lines */
- 	d->irq = ssb_mips_irq(extpci_core->dev) + 2;
- 	pci_write_config_byte(d, PCI_INTERRUPT_LINE, d->irq);
---- a/drivers/ssb/main.c
-+++ b/drivers/ssb/main.c
-@@ -833,6 +833,9 @@ int ssb_bus_pcibus_register(struct ssb_b
- 	if (!err) {
- 		ssb_printk(KERN_INFO PFX "Sonics Silicon Backplane found on "
- 			   "PCI device %s\n", dev_name(&host_pci->dev));
-+	} else {
-+		ssb_printk(KERN_ERR PFX "Failed to register PCI version"
-+			   " of SSB with error %d\n", err);
- 	}
- 
- 	return err;
---- a/drivers/ssb/ssb_private.h
-+++ b/drivers/ssb/ssb_private.h
-@@ -196,7 +196,7 @@ extern int ssb_devices_thaw(struct ssb_f
- #ifdef CONFIG_SSB_B43_PCI_BRIDGE
- extern int __init b43_pci_ssb_bridge_init(void);
- extern void __exit b43_pci_ssb_bridge_exit(void);
--#else /* CONFIG_SSB_B43_PCI_BRIDGR */
-+#else /* CONFIG_SSB_B43_PCI_BRIDGE */
- static inline int b43_pci_ssb_bridge_init(void)
- {
- 	return 0;
-@@ -204,6 +204,6 @@ static inline int b43_pci_ssb_bridge_ini
- static inline void b43_pci_ssb_bridge_exit(void)
- {
- }
--#endif /* CONFIG_SSB_PCIHOST */
-+#endif /* CONFIG_SSB_B43_PCI_BRIDGE */
- 
- #endif /* LINUX_SSB_PRIVATE_H_ */
---- a/include/linux/ssb/ssb_driver_chipcommon.h
-+++ b/include/linux/ssb/ssb_driver_chipcommon.h
-@@ -54,6 +54,7 @@
- #define  SSB_CHIPCO_CAP_64BIT		0x08000000	/* 64-bit Backplane */
- #define  SSB_CHIPCO_CAP_PMU		0x10000000	/* PMU available (rev >= 20) */
- #define  SSB_CHIPCO_CAP_ECI		0x20000000	/* ECI available (rev >= 20) */
-+#define  SSB_CHIPCO_CAP_SPROM		0x40000000	/* SPROM present */
- #define SSB_CHIPCO_CORECTL		0x0008
- #define  SSB_CHIPCO_CORECTL_UARTCLK0	0x00000001	/* Drive UART with internal clock */
- #define	 SSB_CHIPCO_CORECTL_SE		0x00000002	/* sync clk out enable (corerev >= 3) */
-@@ -386,6 +387,7 @@
- 
- 
- /** Chip specific Chip-Status register contents. */
-+#define SSB_CHIPCO_CHST_4322_SPROM_EXISTS	0x00000040 /* SPROM present */
- #define SSB_CHIPCO_CHST_4325_SPROM_OTP_SEL	0x00000003
- #define SSB_CHIPCO_CHST_4325_DEFCIS_SEL		0 /* OTP is powered up, use def. CIS, no SPROM */
- #define SSB_CHIPCO_CHST_4325_SPROM_SEL		1 /* OTP is powered up, SPROM is present */
-@@ -399,6 +401,18 @@
- #define SSB_CHIPCO_CHST_4325_RCAL_VALUE_SHIFT	4
- #define SSB_CHIPCO_CHST_4325_PMUTOP_2B 		0x00000200 /* 1 for 2b, 0 for to 2a */
- 
-+/** Macros to determine SPROM presence based on Chip-Status register. */
-+#define SSB_CHIPCO_CHST_4312_SPROM_PRESENT(status) \
-+	((status & SSB_CHIPCO_CHST_4325_SPROM_OTP_SEL) != \
-+		SSB_CHIPCO_CHST_4325_OTP_SEL)
-+#define SSB_CHIPCO_CHST_4322_SPROM_PRESENT(status) \
-+	(status & SSB_CHIPCO_CHST_4322_SPROM_EXISTS)
-+#define SSB_CHIPCO_CHST_4325_SPROM_PRESENT(status) \
-+	(((status & SSB_CHIPCO_CHST_4325_SPROM_OTP_SEL) != \
-+		SSB_CHIPCO_CHST_4325_DEFCIS_SEL) && \
-+	 ((status & SSB_CHIPCO_CHST_4325_SPROM_OTP_SEL) != \
-+		SSB_CHIPCO_CHST_4325_OTP_SEL))
-+
- 
- 
- /** Clockcontrol masks and values **/
---- a/include/linux/ssb/ssb_regs.h
-+++ b/include/linux/ssb/ssb_regs.h
-@@ -178,19 +178,19 @@
- #define  SSB_SPROM_REVISION_CRC_SHIFT	8
- 
- /* SPROM Revision 1 */
--#define SSB_SPROM1_SPID			0x1004	/* Subsystem Product ID for PCI */
--#define SSB_SPROM1_SVID			0x1006	/* Subsystem Vendor ID for PCI */
--#define SSB_SPROM1_PID			0x1008	/* Product ID for PCI */
--#define SSB_SPROM1_IL0MAC		0x1048	/* 6 bytes MAC address for 802.11b/g */
--#define SSB_SPROM1_ET0MAC		0x104E	/* 6 bytes MAC address for Ethernet */
--#define SSB_SPROM1_ET1MAC		0x1054	/* 6 bytes MAC address for 802.11a */
--#define SSB_SPROM1_ETHPHY		0x105A	/* Ethernet PHY settings */
-+#define SSB_SPROM1_SPID			0x0004	/* Subsystem Product ID for PCI */
-+#define SSB_SPROM1_SVID			0x0006	/* Subsystem Vendor ID for PCI */
-+#define SSB_SPROM1_PID			0x0008	/* Product ID for PCI */
-+#define SSB_SPROM1_IL0MAC		0x0048	/* 6 bytes MAC address for 802.11b/g */
-+#define SSB_SPROM1_ET0MAC		0x004E	/* 6 bytes MAC address for Ethernet */
-+#define SSB_SPROM1_ET1MAC		0x0054	/* 6 bytes MAC address for 802.11a */
-+#define SSB_SPROM1_ETHPHY		0x005A	/* Ethernet PHY settings */
- #define  SSB_SPROM1_ETHPHY_ET0A		0x001F	/* MII Address for enet0 */
- #define  SSB_SPROM1_ETHPHY_ET1A		0x03E0	/* MII Address for enet1 */
- #define  SSB_SPROM1_ETHPHY_ET1A_SHIFT	5
- #define  SSB_SPROM1_ETHPHY_ET0M		(1<<14)	/* MDIO for enet0 */
- #define  SSB_SPROM1_ETHPHY_ET1M		(1<<15)	/* MDIO for enet1 */
--#define SSB_SPROM1_BINF			0x105C	/* Board info */
-+#define SSB_SPROM1_BINF			0x005C	/* Board info */
- #define  SSB_SPROM1_BINF_BREV		0x00FF	/* Board Revision */
- #define  SSB_SPROM1_BINF_CCODE		0x0F00	/* Country Code */
- #define  SSB_SPROM1_BINF_CCODE_SHIFT	8
-@@ -198,63 +198,63 @@
- #define  SSB_SPROM1_BINF_ANTBG_SHIFT	12
- #define  SSB_SPROM1_BINF_ANTA		0xC000	/* Available A-PHY antennas */
- #define  SSB_SPROM1_BINF_ANTA_SHIFT	14
--#define SSB_SPROM1_PA0B0		0x105E
--#define SSB_SPROM1_PA0B1		0x1060
--#define SSB_SPROM1_PA0B2		0x1062
--#define SSB_SPROM1_GPIOA		0x1064	/* General Purpose IO pins 0 and 1 */
-+#define SSB_SPROM1_PA0B0		0x005E
-+#define SSB_SPROM1_PA0B1		0x0060
-+#define SSB_SPROM1_PA0B2		0x0062
-+#define SSB_SPROM1_GPIOA		0x0064	/* General Purpose IO pins 0 and 1 */
- #define  SSB_SPROM1_GPIOA_P0		0x00FF	/* Pin 0 */
- #define  SSB_SPROM1_GPIOA_P1		0xFF00	/* Pin 1 */
- #define  SSB_SPROM1_GPIOA_P1_SHIFT	8
--#define SSB_SPROM1_GPIOB		0x1066	/* General Purpuse IO pins 2 and 3 */
-+#define SSB_SPROM1_GPIOB		0x0066	/* General Purpuse IO pins 2 and 3 */
- #define  SSB_SPROM1_GPIOB_P2		0x00FF	/* Pin 2 */
- #define  SSB_SPROM1_GPIOB_P3		0xFF00	/* Pin 3 */
- #define  SSB_SPROM1_GPIOB_P3_SHIFT	8
--#define SSB_SPROM1_MAXPWR		0x1068	/* Power Amplifier Max Power */
-+#define SSB_SPROM1_MAXPWR		0x0068	/* Power Amplifier Max Power */
- #define  SSB_SPROM1_MAXPWR_BG		0x00FF	/* B-PHY and G-PHY (in dBm Q5.2) */
- #define  SSB_SPROM1_MAXPWR_A		0xFF00	/* A-PHY (in dBm Q5.2) */
- #define  SSB_SPROM1_MAXPWR_A_SHIFT	8
--#define SSB_SPROM1_PA1B0		0x106A
--#define SSB_SPROM1_PA1B1		0x106C
--#define SSB_SPROM1_PA1B2		0x106E
--#define SSB_SPROM1_ITSSI		0x1070	/* Idle TSSI Target */
-+#define SSB_SPROM1_PA1B0		0x006A
-+#define SSB_SPROM1_PA1B1		0x006C
-+#define SSB_SPROM1_PA1B2		0x006E
-+#define SSB_SPROM1_ITSSI		0x0070	/* Idle TSSI Target */
- #define  SSB_SPROM1_ITSSI_BG		0x00FF	/* B-PHY and G-PHY*/
- #define  SSB_SPROM1_ITSSI_A		0xFF00	/* A-PHY */
- #define  SSB_SPROM1_ITSSI_A_SHIFT	8
--#define SSB_SPROM1_BFLLO		0x1072	/* Boardflags (low 16 bits) */
--#define SSB_SPROM1_AGAIN		0x1074	/* Antenna Gain (in dBm Q5.2) */
-+#define SSB_SPROM1_BFLLO		0x0072	/* Boardflags (low 16 bits) */
-+#define SSB_SPROM1_AGAIN		0x0074	/* Antenna Gain (in dBm Q5.2) */
- #define  SSB_SPROM1_AGAIN_BG		0x00FF	/* B-PHY and G-PHY */
- #define  SSB_SPROM1_AGAIN_BG_SHIFT	0
- #define  SSB_SPROM1_AGAIN_A		0xFF00	/* A-PHY */
- #define  SSB_SPROM1_AGAIN_A_SHIFT	8
- 
- /* SPROM Revision 2 (inherits from rev 1) */
--#define SSB_SPROM2_BFLHI		0x1038	/* Boardflags (high 16 bits) */
--#define SSB_SPROM2_MAXP_A		0x103A	/* A-PHY Max Power */
-+#define SSB_SPROM2_BFLHI		0x0038	/* Boardflags (high 16 bits) */
-+#define SSB_SPROM2_MAXP_A		0x003A	/* A-PHY Max Power */
- #define  SSB_SPROM2_MAXP_A_HI		0x00FF	/* Max Power High */
- #define  SSB_SPROM2_MAXP_A_LO		0xFF00	/* Max Power Low */
- #define  SSB_SPROM2_MAXP_A_LO_SHIFT	8
--#define SSB_SPROM2_PA1LOB0		0x103C	/* A-PHY PowerAmplifier Low Settings */
--#define SSB_SPROM2_PA1LOB1		0x103E	/* A-PHY PowerAmplifier Low Settings */
--#define SSB_SPROM2_PA1LOB2		0x1040	/* A-PHY PowerAmplifier Low Settings */
--#define SSB_SPROM2_PA1HIB0		0x1042	/* A-PHY PowerAmplifier High Settings */
--#define SSB_SPROM2_PA1HIB1		0x1044	/* A-PHY PowerAmplifier High Settings */
--#define SSB_SPROM2_PA1HIB2		0x1046	/* A-PHY PowerAmplifier High Settings */
--#define SSB_SPROM2_OPO			0x1078	/* OFDM Power Offset from CCK Level */
-+#define SSB_SPROM2_PA1LOB0		0x003C	/* A-PHY PowerAmplifier Low Settings */
-+#define SSB_SPROM2_PA1LOB1		0x003E	/* A-PHY PowerAmplifier Low Settings */
-+#define SSB_SPROM2_PA1LOB2		0x0040	/* A-PHY PowerAmplifier Low Settings */
-+#define SSB_SPROM2_PA1HIB0		0x0042	/* A-PHY PowerAmplifier High Settings */
-+#define SSB_SPROM2_PA1HIB1		0x0044	/* A-PHY PowerAmplifier High Settings */
-+#define SSB_SPROM2_PA1HIB2		0x0046	/* A-PHY PowerAmplifier High Settings */
-+#define SSB_SPROM2_OPO			0x0078	/* OFDM Power Offset from CCK Level */
- #define  SSB_SPROM2_OPO_VALUE		0x00FF
- #define  SSB_SPROM2_OPO_UNUSED		0xFF00
--#define SSB_SPROM2_CCODE		0x107C	/* Two char Country Code */
-+#define SSB_SPROM2_CCODE		0x007C	/* Two char Country Code */
- 
- /* SPROM Revision 3 (inherits most data from rev 2) */
--#define SSB_SPROM3_IL0MAC		0x104A	/* 6 bytes MAC address for 802.11b/g */
--#define SSB_SPROM3_OFDMAPO		0x102C	/* A-PHY OFDM Mid Power Offset (4 bytes, BigEndian) */
--#define SSB_SPROM3_OFDMALPO		0x1030	/* A-PHY OFDM Low Power Offset (4 bytes, BigEndian) */
--#define SSB_SPROM3_OFDMAHPO		0x1034	/* A-PHY OFDM High Power Offset (4 bytes, BigEndian) */
--#define SSB_SPROM3_GPIOLDC		0x1042	/* GPIO LED Powersave Duty Cycle (4 bytes, BigEndian) */
-+#define SSB_SPROM3_OFDMAPO		0x002C	/* A-PHY OFDM Mid Power Offset (4 bytes, BigEndian) */
-+#define SSB_SPROM3_OFDMALPO		0x0030	/* A-PHY OFDM Low Power Offset (4 bytes, BigEndian) */
-+#define SSB_SPROM3_OFDMAHPO		0x0034	/* A-PHY OFDM High Power Offset (4 bytes, BigEndian) */
-+#define SSB_SPROM3_GPIOLDC		0x0042	/* GPIO LED Powersave Duty Cycle (4 bytes, BigEndian) */
- #define  SSB_SPROM3_GPIOLDC_OFF		0x0000FF00	/* Off Count */
- #define  SSB_SPROM3_GPIOLDC_OFF_SHIFT	8
- #define  SSB_SPROM3_GPIOLDC_ON		0x00FF0000	/* On Count */
- #define  SSB_SPROM3_GPIOLDC_ON_SHIFT	16
--#define SSB_SPROM3_CCKPO		0x1078	/* CCK Power Offset */
-+#define SSB_SPROM3_IL0MAC		0x004A	/* 6 bytes MAC address for 802.11b/g */
-+#define SSB_SPROM3_CCKPO		0x0078	/* CCK Power Offset */
- #define  SSB_SPROM3_CCKPO_1M		0x000F	/* 1M Rate PO */
- #define  SSB_SPROM3_CCKPO_2M		0x00F0	/* 2M Rate PO */
- #define  SSB_SPROM3_CCKPO_2M_SHIFT	4
-@@ -265,100 +265,100 @@
- #define  SSB_SPROM3_OFDMGPO		0x107A	/* G-PHY OFDM Power Offset (4 bytes, BigEndian) */
- 
- /* SPROM Revision 4 */
--#define SSB_SPROM4_IL0MAC		0x104C	/* 6 byte MAC address for a/b/g/n */
--#define SSB_SPROM4_ETHPHY		0x105A	/* Ethernet PHY settings ?? */
-+#define SSB_SPROM4_BFLLO		0x0044	/* Boardflags (low 16 bits) */
-+#define SSB_SPROM4_BFLHI		0x0046  /* Board Flags Hi */
-+#define SSB_SPROM4_IL0MAC		0x004C	/* 6 byte MAC address for a/b/g/n */
-+#define SSB_SPROM4_CCODE		0x0052	/* Country Code (2 bytes) */
-+#define SSB_SPROM4_GPIOA		0x0056	/* Gen. Purpose IO # 0 and 1 */
-+#define  SSB_SPROM4_GPIOA_P0		0x00FF	/* Pin 0 */
-+#define  SSB_SPROM4_GPIOA_P1		0xFF00	/* Pin 1 */
-+#define  SSB_SPROM4_GPIOA_P1_SHIFT	8
-+#define SSB_SPROM4_GPIOB		0x0058	/* Gen. Purpose IO # 2 and 3 */
-+#define  SSB_SPROM4_GPIOB_P2		0x00FF	/* Pin 2 */
-+#define  SSB_SPROM4_GPIOB_P3		0xFF00	/* Pin 3 */
-+#define  SSB_SPROM4_GPIOB_P3_SHIFT	8
-+#define SSB_SPROM4_ETHPHY		0x005A	/* Ethernet PHY settings ?? */
- #define  SSB_SPROM4_ETHPHY_ET0A		0x001F	/* MII Address for enet0 */
- #define  SSB_SPROM4_ETHPHY_ET1A		0x03E0	/* MII Address for enet1 */
- #define  SSB_SPROM4_ETHPHY_ET1A_SHIFT	5
- #define  SSB_SPROM4_ETHPHY_ET0M		(1<<14)	/* MDIO for enet0 */
- #define  SSB_SPROM4_ETHPHY_ET1M		(1<<15)	/* MDIO for enet1 */
--#define SSB_SPROM4_CCODE		0x1052	/* Country Code (2 bytes) */
--#define SSB_SPROM4_ANTAVAIL		0x105D  /* Antenna available bitfields */
--#define SSB_SPROM4_ANTAVAIL_A		0x00FF	/* A-PHY bitfield */
--#define SSB_SPROM4_ANTAVAIL_A_SHIFT	0
--#define SSB_SPROM4_ANTAVAIL_BG		0xFF00	/* B-PHY and G-PHY bitfield */
--#define SSB_SPROM4_ANTAVAIL_BG_SHIFT	8
--#define SSB_SPROM4_BFLLO		0x1044	/* Boardflags (low 16 bits) */
--#define SSB_SPROM4_AGAIN01		0x105E	/* Antenna Gain (in dBm Q5.2) */
-+#define SSB_SPROM4_ANTAVAIL		0x005D  /* Antenna available bitfields */
-+#define  SSB_SPROM4_ANTAVAIL_A		0x00FF	/* A-PHY bitfield */
-+#define  SSB_SPROM4_ANTAVAIL_A_SHIFT	0
-+#define  SSB_SPROM4_ANTAVAIL_BG		0xFF00	/* B-PHY and G-PHY bitfield */
-+#define  SSB_SPROM4_ANTAVAIL_BG_SHIFT	8
-+#define SSB_SPROM4_AGAIN01		0x005E	/* Antenna Gain (in dBm Q5.2) */
- #define  SSB_SPROM4_AGAIN0		0x00FF	/* Antenna 0 */
- #define  SSB_SPROM4_AGAIN0_SHIFT	0
- #define  SSB_SPROM4_AGAIN1		0xFF00	/* Antenna 1 */
- #define  SSB_SPROM4_AGAIN1_SHIFT	8
--#define SSB_SPROM4_AGAIN23		0x1060
-+#define SSB_SPROM4_AGAIN23		0x0060
- #define  SSB_SPROM4_AGAIN2		0x00FF	/* Antenna 2 */
- #define  SSB_SPROM4_AGAIN2_SHIFT	0
- #define  SSB_SPROM4_AGAIN3		0xFF00	/* Antenna 3 */
- #define  SSB_SPROM4_AGAIN3_SHIFT	8
--#define SSB_SPROM4_BFLHI		0x1046  /* Board Flags Hi */
--#define SSB_SPROM4_MAXP_BG		0x1080  /* Max Power BG in path 1 */
-+#define SSB_SPROM4_MAXP_BG		0x0080  /* Max Power BG in path 1 */
- #define  SSB_SPROM4_MAXP_BG_MASK	0x00FF  /* Mask for Max Power BG */
- #define  SSB_SPROM4_ITSSI_BG		0xFF00	/* Mask for path 1 itssi_bg */
- #define  SSB_SPROM4_ITSSI_BG_SHIFT	8
--#define SSB_SPROM4_MAXP_A		0x108A  /* Max Power A in path 1 */
-+#define SSB_SPROM4_MAXP_A		0x008A  /* Max Power A in path 1 */
- #define  SSB_SPROM4_MAXP_A_MASK		0x00FF  /* Mask for Max Power A */
- #define  SSB_SPROM4_ITSSI_A		0xFF00	/* Mask for path 1 itssi_a */
- #define  SSB_SPROM4_ITSSI_A_SHIFT	8
--#define SSB_SPROM4_GPIOA		0x1056	/* Gen. Purpose IO # 0 and 1 */
--#define  SSB_SPROM4_GPIOA_P0		0x00FF	/* Pin 0 */
--#define  SSB_SPROM4_GPIOA_P1		0xFF00	/* Pin 1 */
--#define  SSB_SPROM4_GPIOA_P1_SHIFT	8
--#define SSB_SPROM4_GPIOB		0x1058	/* Gen. Purpose IO # 2 and 3 */
--#define  SSB_SPROM4_GPIOB_P2		0x00FF	/* Pin 2 */
--#define  SSB_SPROM4_GPIOB_P3		0xFF00	/* Pin 3 */
--#define  SSB_SPROM4_GPIOB_P3_SHIFT	8
--#define SSB_SPROM4_PA0B0		0x1082	/* The paXbY locations are */
--#define SSB_SPROM4_PA0B1		0x1084	/*   only guesses */
--#define SSB_SPROM4_PA0B2		0x1086
--#define SSB_SPROM4_PA1B0		0x108E
--#define SSB_SPROM4_PA1B1		0x1090
--#define SSB_SPROM4_PA1B2		0x1092
-+#define SSB_SPROM4_PA0B0		0x0082	/* The paXbY locations are */
-+#define SSB_SPROM4_PA0B1		0x0084	/*   only guesses */
-+#define SSB_SPROM4_PA0B2		0x0086
-+#define SSB_SPROM4_PA1B0		0x008E
-+#define SSB_SPROM4_PA1B1		0x0090
-+#define SSB_SPROM4_PA1B2		0x0092
- 
- /* SPROM Revision 5 (inherits most data from rev 4) */
--#define SSB_SPROM5_BFLLO		0x104A	/* Boardflags (low 16 bits) */
--#define SSB_SPROM5_BFLHI		0x104C  /* Board Flags Hi */
--#define SSB_SPROM5_IL0MAC		0x1052	/* 6 byte MAC address for a/b/g/n */
--#define SSB_SPROM5_CCODE		0x1044	/* Country Code (2 bytes) */
--#define SSB_SPROM5_GPIOA		0x1076	/* Gen. Purpose IO # 0 and 1 */
-+#define SSB_SPROM5_CCODE		0x0044	/* Country Code (2 bytes) */
-+#define SSB_SPROM5_BFLLO		0x004A	/* Boardflags (low 16 bits) */
-+#define SSB_SPROM5_BFLHI		0x004C  /* Board Flags Hi */
-+#define SSB_SPROM5_IL0MAC		0x0052	/* 6 byte MAC address for a/b/g/n */
-+#define SSB_SPROM5_GPIOA		0x0076	/* Gen. Purpose IO # 0 and 1 */
- #define  SSB_SPROM5_GPIOA_P0		0x00FF	/* Pin 0 */
- #define  SSB_SPROM5_GPIOA_P1		0xFF00	/* Pin 1 */
- #define  SSB_SPROM5_GPIOA_P1_SHIFT	8
--#define SSB_SPROM5_GPIOB		0x1078	/* Gen. Purpose IO # 2 and 3 */
-+#define SSB_SPROM5_GPIOB		0x0078	/* Gen. Purpose IO # 2 and 3 */
- #define  SSB_SPROM5_GPIOB_P2		0x00FF	/* Pin 2 */
- #define  SSB_SPROM5_GPIOB_P3		0xFF00	/* Pin 3 */
- #define  SSB_SPROM5_GPIOB_P3_SHIFT	8
- 
- /* SPROM Revision 8 */
--#define SSB_SPROM8_BOARDREV		0x1082	/* Board revision */
--#define SSB_SPROM8_BFLLO		0x1084	/* Board flags (bits 0-15) */
--#define SSB_SPROM8_BFLHI		0x1086	/* Board flags (bits 16-31) */
--#define SSB_SPROM8_BFL2LO		0x1088	/* Board flags (bits 32-47) */
--#define SSB_SPROM8_BFL2HI		0x108A	/* Board flags (bits 48-63) */
--#define SSB_SPROM8_IL0MAC		0x108C	/* 6 byte MAC address */
--#define SSB_SPROM8_CCODE		0x1092	/* 2 byte country code */
--#define SSB_SPROM8_ANTAVAIL		0x109C  /* Antenna available bitfields*/
--#define SSB_SPROM8_ANTAVAIL_A		0xFF00	/* A-PHY bitfield */
--#define SSB_SPROM8_ANTAVAIL_A_SHIFT	8
--#define SSB_SPROM8_ANTAVAIL_BG		0x00FF	/* B-PHY and G-PHY bitfield */
--#define SSB_SPROM8_ANTAVAIL_BG_SHIFT	0
--#define SSB_SPROM8_AGAIN01		0x109E	/* Antenna Gain (in dBm Q5.2) */
-+#define SSB_SPROM8_BOARDREV		0x0082	/* Board revision */
-+#define SSB_SPROM8_BFLLO		0x0084	/* Board flags (bits 0-15) */
-+#define SSB_SPROM8_BFLHI		0x0086	/* Board flags (bits 16-31) */
-+#define SSB_SPROM8_BFL2LO		0x0088	/* Board flags (bits 32-47) */
-+#define SSB_SPROM8_BFL2HI		0x008A	/* Board flags (bits 48-63) */
-+#define SSB_SPROM8_IL0MAC		0x008C	/* 6 byte MAC address */
-+#define SSB_SPROM8_CCODE		0x0092	/* 2 byte country code */
-+#define SSB_SPROM8_GPIOA		0x0096	/*Gen. Purpose IO # 0 and 1 */
-+#define  SSB_SPROM8_GPIOA_P0		0x00FF	/* Pin 0 */
-+#define  SSB_SPROM8_GPIOA_P1		0xFF00	/* Pin 1 */
-+#define  SSB_SPROM8_GPIOA_P1_SHIFT	8
-+#define SSB_SPROM8_GPIOB		0x0098	/* Gen. Purpose IO # 2 and 3 */
-+#define  SSB_SPROM8_GPIOB_P2		0x00FF	/* Pin 2 */
-+#define  SSB_SPROM8_GPIOB_P3		0xFF00	/* Pin 3 */
-+#define  SSB_SPROM8_GPIOB_P3_SHIFT	8
-+#define SSB_SPROM8_ANTAVAIL		0x009C  /* Antenna available bitfields*/
-+#define  SSB_SPROM8_ANTAVAIL_A		0xFF00	/* A-PHY bitfield */
-+#define  SSB_SPROM8_ANTAVAIL_A_SHIFT	8
-+#define  SSB_SPROM8_ANTAVAIL_BG		0x00FF	/* B-PHY and G-PHY bitfield */
-+#define  SSB_SPROM8_ANTAVAIL_BG_SHIFT	0
-+#define SSB_SPROM8_AGAIN01		0x009E	/* Antenna Gain (in dBm Q5.2) */
- #define  SSB_SPROM8_AGAIN0		0x00FF	/* Antenna 0 */
- #define  SSB_SPROM8_AGAIN0_SHIFT	0
- #define  SSB_SPROM8_AGAIN1		0xFF00	/* Antenna 1 */
- #define  SSB_SPROM8_AGAIN1_SHIFT	8
--#define SSB_SPROM8_AGAIN23		0x10A0
-+#define SSB_SPROM8_AGAIN23		0x00A0
- #define  SSB_SPROM8_AGAIN2		0x00FF	/* Antenna 2 */
- #define  SSB_SPROM8_AGAIN2_SHIFT	0
- #define  SSB_SPROM8_AGAIN3		0xFF00	/* Antenna 3 */
- #define  SSB_SPROM8_AGAIN3_SHIFT	8
--#define SSB_SPROM8_GPIOA		0x1096	/*Gen. Purpose IO # 0 and 1 */
--#define  SSB_SPROM8_GPIOA_P0		0x00FF	/* Pin 0 */
--#define  SSB_SPROM8_GPIOA_P1		0xFF00	/* Pin 1 */
--#define  SSB_SPROM8_GPIOA_P1_SHIFT	8
--#define SSB_SPROM8_GPIOB		0x1098	/* Gen. Purpose IO # 2 and 3 */
--#define  SSB_SPROM8_GPIOB_P2		0x00FF	/* Pin 2 */
--#define  SSB_SPROM8_GPIOB_P3		0xFF00	/* Pin 3 */
--#define  SSB_SPROM8_GPIOB_P3_SHIFT	8
--#define SSB_SPROM8_RSSIPARM2G		0x10A4	/* RSSI params for 2GHz */
-+#define SSB_SPROM8_RSSIPARM2G		0x00A4	/* RSSI params for 2GHz */
- #define  SSB_SPROM8_RSSISMF2G		0x000F
- #define  SSB_SPROM8_RSSISMC2G		0x00F0
- #define  SSB_SPROM8_RSSISMC2G_SHIFT	4
-@@ -366,7 +366,7 @@
- #define  SSB_SPROM8_RSSISAV2G_SHIFT	8
- #define  SSB_SPROM8_BXA2G		0x1800
- #define  SSB_SPROM8_BXA2G_SHIFT		11
--#define SSB_SPROM8_RSSIPARM5G		0x10A6	/* RSSI params for 5GHz */
-+#define SSB_SPROM8_RSSIPARM5G		0x00A6	/* RSSI params for 5GHz */
- #define  SSB_SPROM8_RSSISMF5G		0x000F
- #define  SSB_SPROM8_RSSISMC5G		0x00F0
- #define  SSB_SPROM8_RSSISMC5G_SHIFT	4
-@@ -374,47 +374,47 @@
- #define  SSB_SPROM8_RSSISAV5G_SHIFT	8
- #define  SSB_SPROM8_BXA5G		0x1800
- #define  SSB_SPROM8_BXA5G_SHIFT		11
--#define SSB_SPROM8_TRI25G		0x10A8	/* TX isolation 2.4&5.3GHz */
-+#define SSB_SPROM8_TRI25G		0x00A8	/* TX isolation 2.4&5.3GHz */
- #define  SSB_SPROM8_TRI2G		0x00FF	/* TX isolation 2.4GHz */
- #define  SSB_SPROM8_TRI5G		0xFF00	/* TX isolation 5.3GHz */
- #define  SSB_SPROM8_TRI5G_SHIFT		8
--#define SSB_SPROM8_TRI5GHL		0x10AA	/* TX isolation 5.2/5.8GHz */
-+#define SSB_SPROM8_TRI5GHL		0x00AA	/* TX isolation 5.2/5.8GHz */
- #define  SSB_SPROM8_TRI5GL		0x00FF	/* TX isolation 5.2GHz */
- #define  SSB_SPROM8_TRI5GH		0xFF00	/* TX isolation 5.8GHz */
- #define  SSB_SPROM8_TRI5GH_SHIFT	8
--#define SSB_SPROM8_RXPO			0x10AC  /* RX power offsets */
-+#define SSB_SPROM8_RXPO			0x00AC  /* RX power offsets */
- #define  SSB_SPROM8_RXPO2G		0x00FF	/* 2GHz RX power offset */
- #define  SSB_SPROM8_RXPO5G		0xFF00	/* 5GHz RX power offset */
- #define  SSB_SPROM8_RXPO5G_SHIFT	8
--#define SSB_SPROM8_MAXP_BG		0x10C0  /* Max Power 2GHz in path 1 */
-+#define SSB_SPROM8_MAXP_BG		0x00C0  /* Max Power 2GHz in path 1 */
- #define  SSB_SPROM8_MAXP_BG_MASK	0x00FF  /* Mask for Max Power 2GHz */
- #define  SSB_SPROM8_ITSSI_BG		0xFF00	/* Mask for path 1 itssi_bg */
- #define  SSB_SPROM8_ITSSI_BG_SHIFT	8
--#define SSB_SPROM8_PA0B0		0x10C2	/* 2GHz power amp settings */
--#define SSB_SPROM8_PA0B1		0x10C4
--#define SSB_SPROM8_PA0B2		0x10C6
--#define SSB_SPROM8_MAXP_A		0x10C8  /* Max Power 5.3GHz */
-+#define SSB_SPROM8_PA0B0		0x00C2	/* 2GHz power amp settings */
-+#define SSB_SPROM8_PA0B1		0x00C4
-+#define SSB_SPROM8_PA0B2		0x00C6
-+#define SSB_SPROM8_MAXP_A		0x00C8  /* Max Power 5.3GHz */
- #define  SSB_SPROM8_MAXP_A_MASK		0x00FF  /* Mask for Max Power 5.3GHz */
- #define  SSB_SPROM8_ITSSI_A		0xFF00	/* Mask for path 1 itssi_a */
- #define  SSB_SPROM8_ITSSI_A_SHIFT	8
--#define SSB_SPROM8_MAXP_AHL		0x10CA  /* Max Power 5.2/5.8GHz */
-+#define SSB_SPROM8_MAXP_AHL		0x00CA  /* Max Power 5.2/5.8GHz */
- #define  SSB_SPROM8_MAXP_AH_MASK	0x00FF  /* Mask for Max Power 5.8GHz */
- #define  SSB_SPROM8_MAXP_AL_MASK	0xFF00  /* Mask for Max Power 5.2GHz */
- #define  SSB_SPROM8_MAXP_AL_SHIFT	8
--#define SSB_SPROM8_PA1B0		0x10CC	/* 5.3GHz power amp settings */
--#define SSB_SPROM8_PA1B1		0x10CE
--#define SSB_SPROM8_PA1B2		0x10D0
--#define SSB_SPROM8_PA1LOB0		0x10D2	/* 5.2GHz power amp settings */
--#define SSB_SPROM8_PA1LOB1		0x10D4
--#define SSB_SPROM8_PA1LOB2		0x10D6
--#define SSB_SPROM8_PA1HIB0		0x10D8	/* 5.8GHz power amp settings */
--#define SSB_SPROM8_PA1HIB1		0x10DA
--#define SSB_SPROM8_PA1HIB2		0x10DC
--#define SSB_SPROM8_CCK2GPO		0x1140	/* CCK power offset */
--#define SSB_SPROM8_OFDM2GPO		0x1142	/* 2.4GHz OFDM power offset */
--#define SSB_SPROM8_OFDM5GPO		0x1146	/* 5.3GHz OFDM power offset */
--#define SSB_SPROM8_OFDM5GLPO		0x114A	/* 5.2GHz OFDM power offset */
--#define SSB_SPROM8_OFDM5GHPO		0x114E	/* 5.8GHz OFDM power offset */
-+#define SSB_SPROM8_PA1B0		0x00CC	/* 5.3GHz power amp settings */
-+#define SSB_SPROM8_PA1B1		0x00CE
-+#define SSB_SPROM8_PA1B2		0x00D0
-+#define SSB_SPROM8_PA1LOB0		0x00D2	/* 5.2GHz power amp settings */
-+#define SSB_SPROM8_PA1LOB1		0x00D4
-+#define SSB_SPROM8_PA1LOB2		0x00D6
-+#define SSB_SPROM8_PA1HIB0		0x00D8	/* 5.8GHz power amp settings */
-+#define SSB_SPROM8_PA1HIB1		0x00DA
-+#define SSB_SPROM8_PA1HIB2		0x00DC
-+#define SSB_SPROM8_CCK2GPO		0x0140	/* CCK power offset */
-+#define SSB_SPROM8_OFDM2GPO		0x0142	/* 2.4GHz OFDM power offset */
-+#define SSB_SPROM8_OFDM5GPO		0x0146	/* 5.3GHz OFDM power offset */
-+#define SSB_SPROM8_OFDM5GLPO		0x014A	/* 5.2GHz OFDM power offset */
-+#define SSB_SPROM8_OFDM5GHPO		0x014E	/* 5.8GHz OFDM power offset */
- 
- /* Values for SSB_SPROM1_BINF_CCODE */
- enum {