convert brcm-2.4 to the new target structure

git-svn-id: svn://svn.openwrt.org/openwrt/trunk@7092 3c298f89-4303-0410-b956-a3cf2f4a3e73

1 files changed, 516 insertions, 0 deletions

diff --git a/target/linux/brcm-2.4/files/arch/mips/bcm947xx/include/sbchipc.h b/target/linux/brcm-2.4/files/arch/mips/bcm947xx/include/sbchipc.h
new file mode 100644
index 000000000..03c5cf19a
--- /dev/null
+++ b/target/linux/brcm-2.4/files/arch/mips/bcm947xx/include/sbchipc.h
@@ -0,0 +1,516 @@
+/*
+ * SiliconBackplane Chipcommon core hardware definitions.
+ *
+ * The chipcommon core provides chip identification, SB control,
+ * jtag, 0/1/2 uarts, clock frequency control, a watchdog interrupt timer,
+ * gpio interface, extbus, and support for serial and parallel flashes.
+ *
+ * $Id: sbchipc.h,v 1.1.1.14 2006/04/15 01:29:08 michael Exp $
+ * Copyright 2006, Broadcom Corporation
+ * All Rights Reserved.
+ * 
+ * THIS SOFTWARE IS OFFERED "AS IS", AND BROADCOM GRANTS NO WARRANTIES OF ANY
+ * KIND, EXPRESS OR IMPLIED, BY STATUTE, COMMUNICATION OR OTHERWISE. BROADCOM
+ * SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS
+ * FOR A SPECIFIC PURPOSE OR NONINFRINGEMENT CONCERNING THIS SOFTWARE.
+ *
+ */
+
+#ifndef	_SBCHIPC_H
+#define	_SBCHIPC_H
+
+
+#ifndef _LANGUAGE_ASSEMBLY
+
+/* cpp contortions to concatenate w/arg prescan */
+#ifndef PAD
+#define	_PADLINE(line)	pad ## line
+#define	_XSTR(line)	_PADLINE(line)
+#define	PAD		_XSTR(__LINE__)
+#endif	/* PAD */
+
+typedef volatile struct {
+	uint32	chipid;			/* 0x0 */
+	uint32	capabilities;
+	uint32	corecontrol;		/* corerev >= 1 */
+	uint32	bist;
+
+	/* OTP */
+	uint32	otpstatus;		/* 0x10, corerev >= 10 */
+	uint32	otpcontrol;
+	uint32	otpprog;
+	uint32	PAD;
+
+	/* Interrupt control */
+	uint32	intstatus;		/* 0x20 */
+	uint32	intmask;
+	uint32	chipcontrol;		/* 0x28, rev >= 11 */
+	uint32	chipstatus;		/* 0x2c, rev >= 11 */
+
+	/* Jtag Master */
+	uint32	jtagcmd;		/* 0x30, rev >= 10 */
+	uint32	jtagir;
+	uint32	jtagdr;
+	uint32	jtagctrl;
+
+	/* serial flash interface registers */
+	uint32	flashcontrol;		/* 0x40 */
+	uint32	flashaddress;
+	uint32	flashdata;
+	uint32	PAD[1];
+
+	/* Silicon backplane configuration broadcast control */
+	uint32	broadcastaddress;	/* 0x50 */
+	uint32	broadcastdata;
+	uint32	PAD[2];
+
+	/* gpio - cleared only by power-on-reset */
+	uint32	gpioin;			/* 0x60 */
+	uint32	gpioout;
+	uint32	gpioouten;
+	uint32	gpiocontrol;
+	uint32	gpiointpolarity;
+	uint32	gpiointmask;
+	uint32	PAD[2];
+
+	/* Watchdog timer */
+	uint32	watchdog;		/* 0x80 */
+	uint32	PAD[1];
+
+	/* GPIO based LED powersave registers corerev >= 16 */
+	uint32  gpiotimerval;		/* 0x88 */
+	uint32  gpiotimeroutmask;
+
+	/* clock control */
+	uint32	clockcontrol_n;		/* 0x90 */
+	uint32	clockcontrol_sb;	/* aka m0 */
+	uint32	clockcontrol_pci;	/* aka m1 */
+	uint32	clockcontrol_m2;	/* mii/uart/mipsref */
+	uint32	clockcontrol_m3;	/* cpu */
+	uint32	clkdiv;			/* corerev >= 3 */
+	uint32	PAD[2];
+
+	/* pll delay registers (corerev >= 4) */
+	uint32	pll_on_delay;		/* 0xb0 */
+	uint32	fref_sel_delay;
+	uint32	slow_clk_ctl;		/* 5 < corerev < 10 */
+	uint32	PAD[1];
+
+	/* Instaclock registers (corerev >= 10) */
+	uint32	system_clk_ctl;		/* 0xc0 */
+	uint32	clkstatestretch;
+	uint32	PAD[14];
+
+	/* ExtBus control registers (corerev >= 3) */
+	uint32	pcmcia_config;		/* 0x100 */
+	uint32	pcmcia_memwait;
+	uint32	pcmcia_attrwait;
+	uint32	pcmcia_iowait;
+	uint32	ide_config;
+	uint32	ide_memwait;
+	uint32	ide_attrwait;
+	uint32	ide_iowait;
+	uint32	prog_config;
+	uint32	prog_waitcount;
+	uint32	flash_config;
+	uint32	flash_waitcount;
+	uint32	PAD[44];
+
+	/* Clock control and hardware workarounds */
+	uint32	clk_ctl_st;
+	uint32	hw_war;
+	uint32	PAD[70];
+
+	/* uarts */
+	uint8	uart0data;		/* 0x300 */
+	uint8	uart0imr;
+	uint8	uart0fcr;
+	uint8	uart0lcr;
+	uint8	uart0mcr;
+	uint8	uart0lsr;
+	uint8	uart0msr;
+	uint8	uart0scratch;
+	uint8	PAD[248];		/* corerev >= 1 */
+
+	uint8	uart1data;		/* 0x400 */
+	uint8	uart1imr;
+	uint8	uart1fcr;
+	uint8	uart1lcr;
+	uint8	uart1mcr;
+	uint8	uart1lsr;
+	uint8	uart1msr;
+	uint8	uart1scratch;
+} chipcregs_t;
+
+#endif /* _LANGUAGE_ASSEMBLY */
+
+#define	CC_CHIPID		0
+#define	CC_CAPABILITIES		4
+#define	CC_JTAGCMD		0x30
+#define	CC_JTAGIR		0x34
+#define	CC_JTAGDR		0x38
+#define	CC_JTAGCTRL		0x3c
+#define	CC_WATCHDOG		0x80
+#define	CC_CLKC_N		0x90
+#define	CC_CLKC_M0		0x94
+#define	CC_CLKC_M1		0x98
+#define	CC_CLKC_M2		0x9c
+#define	CC_CLKC_M3		0xa0
+#define	CC_CLKDIV		0xa4
+#define	CC_SYS_CLK_CTL		0xc0
+#define	CC_OTP			0x800
+
+/* chipid */
+#define	CID_ID_MASK		0x0000ffff	/* Chip Id mask */
+#define	CID_REV_MASK		0x000f0000	/* Chip Revision mask */
+#define	CID_REV_SHIFT		16		/* Chip Revision shift */
+#define	CID_PKG_MASK		0x00f00000	/* Package Option mask */
+#define	CID_PKG_SHIFT		20		/* Package Option shift */
+#define	CID_CC_MASK		0x0f000000	/* CoreCount (corerev >= 4) */
+#define CID_CC_SHIFT		24
+
+/* capabilities */
+#define	CAP_UARTS_MASK		0x00000003	/* Number of uarts */
+#define CAP_MIPSEB		0x00000004	/* MIPS is in big-endian mode */
+#define CAP_UCLKSEL		0x00000018	/* UARTs clock select */
+#define CAP_UINTCLK		0x00000008	/* UARTs are driven by internal divided clock */
+#define CAP_UARTGPIO		0x00000020	/* UARTs own Gpio's 15:12 */
+#define CAP_EXTBUS_MASK		0x000000c0	/* External bus mask */
+#define CAP_EXTBUS_NONE		0x00000000	/* No ExtBus present */
+#define CAP_EXTBUS_FULL		0x00000040	/* ExtBus: PCMCIA, IDE & Prog */
+#define CAP_EXTBUS_PROG		0x00000080	/* ExtBus: ProgIf only */
+#define	CAP_FLASH_MASK		0x00000700	/* Type of flash */
+#define	CAP_PLL_MASK		0x00038000	/* Type of PLL */
+#define CAP_PWR_CTL		0x00040000	/* Power control */
+#define CAP_OTPSIZE		0x00380000	/* OTP Size (0 = none) */
+#define CAP_OTPSIZE_SHIFT	19		/* OTP Size shift */
+#define CAP_OTPSIZE_BASE	5		/* OTP Size base */
+#define CAP_JTAGP		0x00400000	/* JTAG Master Present */
+#define CAP_ROM			0x00800000	/* Internal boot rom active */
+#define CAP_BKPLN64		0x08000000	/* 64-bit backplane */
+
+/* PLL type */
+#define PLL_NONE		0x00000000
+#define PLL_TYPE1		0x00010000	/* 48Mhz base, 3 dividers */
+#define PLL_TYPE2		0x00020000	/* 48Mhz, 4 dividers */
+#define PLL_TYPE3		0x00030000	/* 25Mhz, 2 dividers */
+#define PLL_TYPE4		0x00008000	/* 48Mhz, 4 dividers */
+#define PLL_TYPE5		0x00018000	/* 25Mhz, 4 dividers */
+#define PLL_TYPE6		0x00028000	/* 100/200 or 120/240 only */
+#define PLL_TYPE7		0x00038000	/* 25Mhz, 4 dividers */
+
+/* corecontrol */
+#define CC_UARTCLKO		0x00000001	/* Drive UART with internal clock */
+#define	CC_SE			0x00000002	/* sync clk out enable (corerev >= 3) */
+
+/* chipcontrol */
+#define CHIPCTRL_4321A0_DEFAULT	0x3a4		
+#define CHIPCTRL_4321A1_DEFAULT	0x0a4		
+
+/* Fields in the otpstatus register */
+#define	OTPS_PROGFAIL		0x80000000
+#define	OTPS_PROTECT		0x00000007
+#define	OTPS_HW_PROTECT		0x00000001
+#define	OTPS_SW_PROTECT		0x00000002
+#define	OTPS_CID_PROTECT	0x00000004
+
+/* Fields in the otpcontrol register */
+#define	OTPC_RECWAIT		0xff000000
+#define	OTPC_PROGWAIT		0x00ffff00
+#define	OTPC_PRW_SHIFT		8
+#define	OTPC_MAXFAIL		0x00000038
+#define	OTPC_VSEL		0x00000006
+#define	OTPC_SELVL		0x00000001
+
+/* Fields in otpprog */
+#define	OTPP_COL_MASK		0x000000ff
+#define	OTPP_ROW_MASK		0x0000ff00
+#define	OTPP_ROW_SHIFT		8
+#define	OTPP_READERR		0x10000000
+#define	OTPP_VALUE		0x20000000
+#define	OTPP_VALUE_SHIFT		29
+#define	OTPP_READ		0x40000000
+#define	OTPP_START		0x80000000
+#define	OTPP_BUSY		0x80000000
+
+/* jtagcmd */
+#define JCMD_START		0x80000000
+#define JCMD_BUSY		0x80000000
+#define JCMD_PAUSE		0x40000000
+#define JCMD0_ACC_MASK		0x0000f000
+#define JCMD0_ACC_IRDR		0x00000000
+#define JCMD0_ACC_DR		0x00001000
+#define JCMD0_ACC_IR		0x00002000
+#define JCMD0_ACC_RESET		0x00003000
+#define JCMD0_ACC_IRPDR		0x00004000
+#define JCMD0_ACC_PDR		0x00005000
+#define JCMD0_IRW_MASK		0x00000f00
+#define JCMD_ACC_MASK		0x000f0000	/* Changes for corerev 11 */
+#define JCMD_ACC_IRDR		0x00000000
+#define JCMD_ACC_DR		0x00010000
+#define JCMD_ACC_IR		0x00020000
+#define JCMD_ACC_RESET		0x00030000
+#define JCMD_ACC_IRPDR		0x00040000
+#define JCMD_ACC_PDR		0x00050000
+#define JCMD_IRW_MASK		0x00001f00
+#define JCMD_IRW_SHIFT		8
+#define JCMD_DRW_MASK		0x0000003f
+
+/* jtagctrl */
+#define JCTRL_FORCE_CLK		4		/* Force clock */
+#define JCTRL_EXT_EN		2		/* Enable external targets */
+#define JCTRL_EN		1		/* Enable Jtag master */
+
+/* Fields in clkdiv */
+#define	CLKD_SFLASH		0x0f000000
+#define	CLKD_SFLASH_SHIFT	24
+#define	CLKD_OTP		0x000f0000
+#define	CLKD_OTP_SHIFT		16
+#define	CLKD_JTAG		0x00000f00
+#define	CLKD_JTAG_SHIFT		8
+#define	CLKD_UART		0x000000ff
+
+/* intstatus/intmask */
+#define	CI_GPIO			0x00000001	/* gpio intr */
+#define	CI_EI			0x00000002	/* ro: ext intr pin (corerev >= 3) */
+#define	CI_WDRESET		0x80000000	/* watchdog reset occurred */
+
+/* slow_clk_ctl */
+#define SCC_SS_MASK		0x00000007	/* slow clock source mask */
+#define	SCC_SS_LPO		0x00000000	/* source of slow clock is LPO */
+#define	SCC_SS_XTAL		0x00000001	/* source of slow clock is crystal */
+#define	SCC_SS_PCI		0x00000002	/* source of slow clock is PCI */
+#define SCC_LF			0x00000200	/* LPOFreqSel, 1: 160Khz, 0: 32KHz */
+#define SCC_LP			0x00000400	/* LPOPowerDown, 1: LPO is disabled,
+						 * 0: LPO is enabled
+						 */
+#define SCC_FS			0x00000800	/* ForceSlowClk, 1: sb/cores running on slow clock,
+						 * 0: power logic control
+						 */
+#define SCC_IP			0x00001000	/* IgnorePllOffReq, 1/0: power logic ignores/honors
+						 * PLL clock disable requests from core
+						 */
+#define SCC_XC			0x00002000	/* XtalControlEn, 1/0: power logic does/doesn't
+						 * disable crystal when appropriate
+						 */
+#define SCC_XP			0x00004000	/* XtalPU (RO), 1/0: crystal running/disabled */
+#define SCC_CD_MASK		0xffff0000	/* ClockDivider (SlowClk = 1/(4+divisor)) */
+#define SCC_CD_SHIFT		16
+
+/* system_clk_ctl */
+#define	SYCC_IE			0x00000001	/* ILPen: Enable Idle Low Power */
+#define	SYCC_AE			0x00000002	/* ALPen: Enable Active Low Power */
+#define	SYCC_FP			0x00000004	/* ForcePLLOn */
+#define	SYCC_AR			0x00000008	/* Force ALP (or HT if ALPen is not set */
+#define	SYCC_HR			0x00000010	/* Force HT */
+#define SYCC_CD_MASK		0xffff0000	/* ClkDiv  (ILP = 1/(4 * (divisor + 1)) */
+#define SYCC_CD_SHIFT		16
+
+/* gpiotimerval */
+#define GPIO_ONTIME_SHIFT	16
+
+/* clockcontrol_n */
+#define	CN_N1_MASK		0x3f		/* n1 control */
+#define	CN_N2_MASK		0x3f00		/* n2 control */
+#define	CN_N2_SHIFT		8
+#define	CN_PLLC_MASK		0xf0000		/* pll control */
+#define	CN_PLLC_SHIFT		16
+
+/* clockcontrol_sb/pci/uart */
+#define	CC_M1_MASK		0x3f		/* m1 control */
+#define	CC_M2_MASK		0x3f00		/* m2 control */
+#define	CC_M2_SHIFT		8
+#define	CC_M3_MASK		0x3f0000	/* m3 control */
+#define	CC_M3_SHIFT		16
+#define	CC_MC_MASK		0x1f000000	/* mux control */
+#define	CC_MC_SHIFT		24
+
+/* N3M Clock control magic field values */
+#define	CC_F6_2			0x02		/* A factor of 2 in */
+#define	CC_F6_3			0x03		/* 6-bit fields like */
+#define	CC_F6_4			0x05		/* N1, M1 or M3 */
+#define	CC_F6_5			0x09
+#define	CC_F6_6			0x11
+#define	CC_F6_7			0x21
+
+#define	CC_F5_BIAS		5		/* 5-bit fields get this added */
+
+#define	CC_MC_BYPASS		0x08
+#define	CC_MC_M1		0x04
+#define	CC_MC_M1M2		0x02
+#define	CC_MC_M1M2M3		0x01
+#define	CC_MC_M1M3		0x11
+
+/* Type 2 Clock control magic field values */
+#define	CC_T2_BIAS		2		/* n1, n2, m1 & m3 bias */
+#define	CC_T2M2_BIAS		3		/* m2 bias */
+
+#define	CC_T2MC_M1BYP		1
+#define	CC_T2MC_M2BYP		2
+#define	CC_T2MC_M3BYP		4
+
+/* Type 6 Clock control magic field values */
+#define	CC_T6_MMASK		1		/* bits of interest in m */
+#define	CC_T6_M0		120000000	/* sb clock for m = 0 */
+#define	CC_T6_M1		100000000	/* sb clock for m = 1 */
+#define	SB2MIPS_T6(sb)		(2 * (sb))
+
+/* Common clock base */
+#define	CC_CLOCK_BASE1		24000000	/* Half the clock freq */
+#define CC_CLOCK_BASE2		12500000	/* Alternate crystal on some PLL's */
+
+/* Clock control values for 200Mhz in 5350 */
+#define	CLKC_5350_N		0x0311
+#define	CLKC_5350_M		0x04020009
+
+/* Flash types in the chipcommon capabilities register */
+#define FLASH_NONE		0x000		/* No flash */
+#define SFLASH_ST		0x100		/* ST serial flash */
+#define SFLASH_AT		0x200		/* Atmel serial flash */
+#define	PFLASH			0x700		/* Parallel flash */
+
+/* Bits in the ExtBus config registers */
+#define	CC_CFG_EN		0x0001		/* Enable */
+#define	CC_CFG_EM_MASK		0x000e		/* Extif Mode */
+#define	CC_CFG_EM_ASYNC		0x0000		/*   Async/Parallel flash */
+#define	CC_CFG_EM_SYNC		0x0002		/*   Synchronous */
+#define	CC_CFG_EM_PCMCIA	0x0004		/*   PCMCIA */
+#define	CC_CFG_EM_IDE		0x0006		/*   IDE */
+#define	CC_CFG_DS		0x0010		/* Data size, 0=8bit, 1=16bit */
+#define	CC_CFG_CD_MASK		0x0060		/* Sync: Clock divisor */
+#define	CC_CFG_CE		0x0080		/* Sync: Clock enable */
+#define	CC_CFG_SB		0x0100		/* Sync: Size/Bytestrobe */
+
+/* ExtBus address space */
+#define	CC_EB_BASE		0x1a000000	/* Chipc ExtBus base address */
+#define	CC_EB_PCMCIA_MEM	0x1a000000	/* PCMCIA 0 memory base address */
+#define	CC_EB_PCMCIA_IO		0x1a200000	/* PCMCIA 0 I/O base address */
+#define	CC_EB_PCMCIA_CFG	0x1a400000	/* PCMCIA 0 config base address */
+#define	CC_EB_IDE		0x1a800000	/* IDE memory base */
+#define	CC_EB_PCMCIA1_MEM	0x1a800000	/* PCMCIA 1 memory base address */
+#define	CC_EB_PCMCIA1_IO	0x1aa00000	/* PCMCIA 1 I/O base address */
+#define	CC_EB_PCMCIA1_CFG	0x1ac00000	/* PCMCIA 1 config base address */
+#define	CC_EB_PROGIF		0x1b000000	/* ProgIF Async/Sync base address */
+
+
+/* Start/busy bit in flashcontrol */
+#define SFLASH_OPCODE		0x000000ff
+#define SFLASH_ACTION		0x00000700
+#define SFLASH_START		0x80000000
+#define SFLASH_BUSY		SFLASH_START
+
+/* flashcontrol action codes */
+#define	SFLASH_ACT_OPONLY	0x0000		/* Issue opcode only */
+#define	SFLASH_ACT_OP1D		0x0100		/* opcode + 1 data byte */
+#define	SFLASH_ACT_OP3A		0x0200		/* opcode + 3 address bytes */
+#define	SFLASH_ACT_OP3A1D	0x0300		/* opcode + 3 addres & 1 data bytes */
+#define	SFLASH_ACT_OP3A4D	0x0400		/* opcode + 3 addres & 4 data bytes */
+#define	SFLASH_ACT_OP3A4X4D	0x0500		/* opcode + 3 addres, 4 don't care & 4 data bytes */
+#define	SFLASH_ACT_OP3A1X4D	0x0700		/* opcode + 3 addres, 1 don't care & 4 data bytes */
+
+/* flashcontrol action+opcodes for ST flashes */
+#define SFLASH_ST_WREN		0x0006		/* Write Enable */
+#define SFLASH_ST_WRDIS		0x0004		/* Write Disable */
+#define SFLASH_ST_RDSR		0x0105		/* Read Status Register */
+#define SFLASH_ST_WRSR		0x0101		/* Write Status Register */
+#define SFLASH_ST_READ		0x0303		/* Read Data Bytes */
+#define SFLASH_ST_PP		0x0302		/* Page Program */
+#define SFLASH_ST_SE		0x02d8		/* Sector Erase */
+#define SFLASH_ST_BE		0x00c7		/* Bulk Erase */
+#define SFLASH_ST_DP		0x00b9		/* Deep Power-down */
+#define SFLASH_ST_RES		0x03ab		/* Read Electronic Signature */
+
+/* Status register bits for ST flashes */
+#define SFLASH_ST_WIP		0x01		/* Write In Progress */
+#define SFLASH_ST_WEL		0x02		/* Write Enable Latch */
+#define SFLASH_ST_BP_MASK	0x1c		/* Block Protect */
+#define SFLASH_ST_BP_SHIFT	2
+#define SFLASH_ST_SRWD		0x80		/* Status Register Write Disable */
+
+/* flashcontrol action+opcodes for Atmel flashes */
+#define SFLASH_AT_READ				0x07e8
+#define SFLASH_AT_PAGE_READ			0x07d2
+#define SFLASH_AT_BUF1_READ
+#define SFLASH_AT_BUF2_READ
+#define SFLASH_AT_STATUS			0x01d7
+#define SFLASH_AT_BUF1_WRITE			0x0384
+#define SFLASH_AT_BUF2_WRITE			0x0387
+#define SFLASH_AT_BUF1_ERASE_PROGRAM		0x0283
+#define SFLASH_AT_BUF2_ERASE_PROGRAM		0x0286
+#define SFLASH_AT_BUF1_PROGRAM			0x0288
+#define SFLASH_AT_BUF2_PROGRAM			0x0289
+#define SFLASH_AT_PAGE_ERASE			0x0281
+#define SFLASH_AT_BLOCK_ERASE			0x0250
+#define SFLASH_AT_BUF1_WRITE_ERASE_PROGRAM	0x0382
+#define SFLASH_AT_BUF2_WRITE_ERASE_PROGRAM	0x0385
+#define SFLASH_AT_BUF1_LOAD			0x0253
+#define SFLASH_AT_BUF2_LOAD			0x0255
+#define SFLASH_AT_BUF1_COMPARE			0x0260
+#define SFLASH_AT_BUF2_COMPARE			0x0261
+#define SFLASH_AT_BUF1_REPROGRAM		0x0258
+#define SFLASH_AT_BUF2_REPROGRAM		0x0259
+
+/* Status register bits for Atmel flashes */
+#define SFLASH_AT_READY				0x80
+#define SFLASH_AT_MISMATCH			0x40
+#define SFLASH_AT_ID_MASK			0x38
+#define SFLASH_AT_ID_SHIFT			3
+
+/* OTP regions */
+#define	OTP_HW_REGION	OTPS_HW_PROTECT
+#define	OTP_SW_REGION	OTPS_SW_PROTECT
+#define	OTP_CID_REGION	OTPS_CID_PROTECT
+
+/* OTP regions (Byte offsets from otp size) */
+#define	OTP_SWLIM_OFF	(-8)
+#define	OTP_CIDBASE_OFF	0
+#define	OTP_CIDLIM_OFF	8
+
+/* Predefined OTP words (Word offset from otp size) */
+#define	OTP_BOUNDARY_OFF (-4)
+#define	OTP_HWSIGN_OFF	(-3)
+#define	OTP_SWSIGN_OFF	(-2)
+#define	OTP_CIDSIGN_OFF	(-1)
+
+#define	OTP_CID_OFF	0
+#define	OTP_PKG_OFF	1
+#define	OTP_FID_OFF	2
+#define	OTP_RSV_OFF	3
+#define	OTP_LIM_OFF	4
+
+#define	OTP_SIGNATURE	0x578a
+#define	OTP_MAGIC	0x4e56
+
+/* 
+ * These are the UART port assignments, expressed as offsets from the base
+ * register.  These assignments should hold for any serial port based on
+ * a 8250, 16450, or 16550(A).
+ */
+
+#define UART_RX		0	/* In:  Receive buffer (DLAB=0) */
+#define UART_TX		0	/* Out: Transmit buffer (DLAB=0) */
+#define UART_DLL	0	/* Out: Divisor Latch Low (DLAB=1) */
+#define UART_IER	1	/* In/Out: Interrupt Enable Register (DLAB=0) */
+#define UART_DLM	1	/* Out: Divisor Latch High (DLAB=1) */
+#define UART_IIR	2	/* In: Interrupt Identity Register  */
+#define UART_FCR	2	/* Out: FIFO Control Register */
+#define UART_LCR	3	/* Out: Line Control Register */
+#define UART_MCR	4	/* Out: Modem Control Register */
+#define UART_LSR	5	/* In:  Line Status Register */
+#define UART_MSR	6	/* In:  Modem Status Register */
+#define UART_SCR	7	/* I/O: Scratch Register */
+#define UART_LCR_DLAB	0x80	/* Divisor latch access bit */
+#define UART_LCR_WLEN8	0x03	/* Wordlength: 8 bits */
+#define UART_MCR_OUT2	0x08	/* MCR GPIO out 2 */
+#define UART_MCR_LOOP	0x10	/* Enable loopback test mode */
+#define UART_LSR_THRE	0x20	/* Transmit-hold-register empty */
+#define UART_LSR_RXRDY	0x01	/* Receiver ready */
+#define UART_FCR_FIFO_ENABLE 1	/* FIFO control register bit controlling FIFO enable/disable */
+
+/* Interrupt Enable Register (IER) bits */
+#define UART_IER_EDSSI	8	/* enable modem status interrupt */
+#define UART_IER_ELSI	4	/* enable receiver line status interrupt */
+#define UART_IER_ETBEI  2	/* enable transmitter holding register empty interrupt */
+#define UART_IER_ERBFI	1	/* enable data available interrupt */
+
+#endif	/* _SBCHIPC_H */