get rid of per-profile base-files

git-svn-id: svn://svn.openwrt.org/openwrt/trunk@9069 3c298f89-4303-0410-b956-a3cf2f4a3e73

3 files changed, 240 insertions, 0 deletions

diff --git a/target/linux/brcm-2.4/base-files/etc/diag.sh b/target/linux/brcm-2.4/base-files/etc/diag.sh
new file mode 100644
index 000000000..3b08554c6
--- /dev/null
+++ b/target/linux/brcm-2.4/base-files/etc/diag.sh
@@ -0,0 +1,28 @@
+#!/bin/sh
+# Copyright (C) 2006 OpenWrt.org
+
+set_led() {
+	local led="$1"
+	local state="$2"
+	[ -f "/proc/diag/led/$1" ] && echo "$state" > "/proc/diag/led/$1"
+}
+
+set_state() {
+	case "$1" in
+		preinit)
+			set_led dmz 1
+			set_led diag 1
+			set_led power 0
+		;;
+		failsafe)
+			set_led diag f
+			set_led power f
+			set_led dmz f
+		;;
+		done)
+			set_led dmz 0
+			set_led diag 0
+			set_led power 1
+		;;
+	esac
+}
diff --git a/target/linux/brcm-2.4/base-files/etc/init.d/netconfig b/target/linux/brcm-2.4/base-files/etc/init.d/netconfig
new file mode 100755
index 000000000..643ba35d3
--- /dev/null
+++ b/target/linux/brcm-2.4/base-files/etc/init.d/netconfig
@@ -0,0 +1,154 @@
+#!/bin/sh /etc/rc.common
+# Copyright (C) 2006 OpenWrt.org
+
+START=05
+
+start() {
+	[ -e /etc/config/network ] && exit 0
+
+	mkdir -p /etc/config
+
+	(
+		if grep -E 'mtd0: 000(6|a)0000' /proc/mtd 2>&- >&-; then
+			# WGT634u
+			echo boardtype=wgt634u
+		else
+			strings "$(find_mtd_part nvram)"
+		fi
+	) | awk '
+	function p(cfgname, name) {
+		if (c[name] != "") print "	option " cfgname "	\"" c[name] "\""
+	}
+
+	function macinc(mac, maca, i, result) {
+		split(mac, maca, ":")
+		for (i = 1; i <= 6; i++) maca[i] = "0x" maca[i]
+		if (++maca[6] > 0xff) {
+			maca[5]++
+			maca[6] = 0
+		}
+		for (i = 1; i <= 6; i++) {
+			if (i != 1) result = result ":"
+			result = result sprintf("%02x", maca[i])
+		}
+		return result
+	}
+
+	BEGIN {
+		FS="="
+		c["lan_ifname"]="eth0.0"
+		c["wan_ifname"]="eth0.1"
+		c["vlan0ports"]="1 2 3 4 5*"
+		c["vlan1ports"]="0 5"
+		getline < "/proc/diag/model"
+		model=$0
+		for (i = 0; i < 6; i++) {
+			if (mac_check != "") mac_check = mac_check ":"
+			mac_check = mac_check "[0-9a-fA-F][0-9a-fA-F]"
+		}
+	}
+
+	($1 == "boardnum") || ($1 == "boardtype") || ($1 == "boardflags") || ($1 ~ /macaddr/) {
+		nvram[$1] = $2
+	}
+
+	END {
+		if ((model == "ASUS WL-HDD") || (model == "ASUS WL-300g") || (model == "Linksys WAP54G V1")) {
+			c["wan_ifname"] = ""
+			c["lan_ifname"] = "eth1"
+		}
+		if (model == "ASUS WL-500g") {
+			c["wan_ifname"] = "eth1"
+			c["lan_ifname"] = "eth0"
+		}
+		if (model == "Dell TrueMobile 2300") {
+			c["vlan0ports"] = "0 1 2 3 5*"
+			c["vlan1ports"] = "4 5"
+		}
+		if (nvram["boardtype"] == "bcm94710r4") {
+			# Toshiba WRC-1000
+			c["lan_ifname"] = "eth0"
+			c["wan_ifname"] = "eth1"
+		}
+		if (nvram["boardtype"] == "wgt634u") {
+			c["vlan0ports"] = "0 1 2 3 5*"
+			c["vlan1ports"] = "4 5"
+		}
+		if (nvram["boardtype"] == "0x0467") {
+			c["vlan0ports"] = "0 1 2 3 5*"
+			c["vlan1ports"] = "4 5"
+		}
+		if ((nvram["boardtype"] == "0x042f") || (nvram["boardtype"] == "0x0472")) {
+			if (nvram["boardnum"] == "45") {
+				# WL-500gP
+				c["vlan0ports"] = "1 2 3 4 5*"
+				c["vlan1ports"] = "0 5"
+			} else {
+				# Generic BCM94704
+				c["vlan0ports"] = "0 1 2 3 4 5u"
+				c["vlan1ports"] = ""
+				c["lan_ifname"] = "eth0"
+				c["wan_ifname"] = "eth1"
+
+				# MAC addresses on 4704 tend to be screwed up. Add a workaround here
+				if (nvram["et0macaddr"] ~ mac_check) {
+					c["lan_macaddr"] = nvram["et0macaddr"]
+					c["wan_macaddr"] = macinc(c["lan_macaddr"])
+				}
+			}
+		}
+
+		# WAP54G
+		if ((nvram["boardnum"] == "2") || \
+			(nvram["boardnum"] == "1024")) {
+			c["lan_ifname"]="eth0"
+			c["wan_ifname"]=""
+		}
+
+		# ASUS WL-700gE
+		# These are actually same as defaults above. For some reason this script applies
+		# Generic BCM94704 settings instead so we revert to proper settings here.
+		# Hopefully someone will fix this properly soon.
+		if (model == "ASUS WL-700gE") {
+			c["lan_ifname"]="eth0.0"
+			c["wan_ifname"]="eth0.1"
+			c["vlan0ports"]="1 2 3 4 5*"
+			c["vlan1ports"]="0 5"
+		}
+
+		if (model == "Motorola WR850G V2/V3") {
+			c["vlan0ports"]="0 1 2 3 5*"
+			c["vlan1ports"]="4 5"
+		}
+
+		print "#### VLAN configuration "
+		print "config switch eth0"
+		p("vlan0", "vlan0ports")
+		p("vlan1", "vlan1ports")
+		print ""
+		print ""
+		print "#### Loopback configuration"
+		print "config interface loopback"
+		print "	option ifname	\"lo\""
+		print "	option proto	static"
+		print "	option ipaddr	127.0.0.1"
+		print "	option netmask	255.0.0.0"
+		print ""
+		print ""
+		print "#### LAN configuration"
+		print "config interface lan"
+		print "	option type 	bridge"
+		p("ifname", "lan_ifname")
+		p("macaddr", "lan_macaddr")
+		print "	option proto	static"
+		print "	option ipaddr	192.168.1.1"
+		print "	option netmask	255.255.255.0"
+		print ""
+		print ""
+		print "#### WAN configuration"
+		print "config interface	wan"
+		p("ifname", "wan_ifname")
+		p("macaddr", "wan_macaddr")
+		print "	option proto	dhcp"
+	}' > /etc/config/network
+}
diff --git a/target/linux/brcm-2.4/base-files/etc/preinit.arch b/target/linux/brcm-2.4/base-files/etc/preinit.arch
new file mode 100755
index 000000000..43df591ab
--- /dev/null
+++ b/target/linux/brcm-2.4/base-files/etc/preinit.arch
@@ -0,0 +1,58 @@
+. /etc/functions.sh
+
+failsafe() {
+	lock /tmp/.failsafe
+	failsafe_ip
+
+	echo "0 1 2 3 4 5u*" > /proc/switch/eth0/vlan/0/ports
+	
+	set_state failsafe
+	[ -x "/usr/sbin/nvram" ] && {
+		[ "$(nvram get boot_wait)" != "on" ] && {
+			nvram set boot_wait=on
+			nvram commit
+		}
+	}
+
+	netmsg 192.168.1.255 "Entering Failsafe!"
+	telnetd -l /bin/login <> /dev/null 2>&1
+
+	ash --login
+}
+
+mount none /proc -t proc
+
+insmod diag
+set_state preinit
+echo '/sbin/hotplug.failsafe' > /proc/sys/kernel/hotplug
+
+ifname=eth0
+
+# hardware specific overrides
+case "$(cat /proc/diag/model)" in
+	"Linksys WAP54G V1") ifname=eth1;;
+	"ASUS WL-HDD") ifname=eth1;;
+	"ASUS WL-300g") ifname=eth1;;
+	"ASUS (unknown, BCM4702)") ifname=eth1;;
+esac
+
+failsafe_ip
+
+insmod switch-core
+insmod switch-robo || insmod switch-adm || rmmod switch-core
+
+[ -d /proc/switch/eth0 ] && {
+	echo 1 > /proc/switch/eth0/reset
+
+	# this would be easier if we blasted the message across all ports
+	# but we don't want packets leaking across interfaces
+	for port in $(seq 0 4); do {
+		echo "$port 5u*" > /proc/switch/eth0/vlan/0/ports
+		netmsg 192.168.1.255 "Press reset now, to enter Failsafe!"
+	}; done
+} || netmsg 192.168.1.255 "Press reset now, to enter Failsafe!"
+
+ifconfig $ifname 0.0.0.0 down
+
+sleep 2
+