[at91] Remove old netus board definition

git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31435 3c298f89-4303-0410-b956-a3cf2f4a3e73

1 files changed, 0 insertions, 242 deletions

diff --git a/target/linux/at91/files/arch/arm/mach-at91/board-netus-foxboard.c b/target/linux/at91/files/arch/arm/mach-at91/board-netus-foxboard.c
deleted file mode 100644
index c0d366ffc..000000000
--- a/target/linux/at91/files/arch/arm/mach-at91/board-netus-foxboard.c
+++ /dev/null
@@ -1,242 +0,0 @@
-/*
- *  Copyright (C) 2005 SAN People
- *  Copyright (C) 2006 Atmel
- *  Copyright (C) 2009-2010 Claudio Mignanti <c.mignanti@gmail.com>
- *
- *  Strongly based on arch/arm/mach-at91/board-sam9260ek.c
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
- */
-
-#include <linux/types.h>
-#include <linux/init.h>
-#include <linux/mm.h>
-#include <linux/module.h>
-#include <linux/platform_device.h>
-#include <linux/spi/spi.h>
-#include <linux/gpio.h>
-#include <linux/gpio_keys.h>
-#include <linux/input.h>
-#include <linux/clk.h>
-
-#include <mach/hardware.h>
-#include <asm/setup.h>
-#include <asm/mach-types.h>
-#include <asm/irq.h>
-
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-#include <asm/mach/irq.h>
-
-#include <mach/board.h>
-#include <mach/at91sam9_smc.h>
-
-#include "sam9_smc.h"
-#include "generic.h"
-
-
-static void __init ek_map_io(void)
-{
-	/* Initialize processor: 18.432 MHz crystal */
-	at91sam9260_initialize(18432000);
-
-	/* DGBU on ttyS0. (Rx & Tx only) */
-	at91_register_uart(0, 0, 0);
-
-#if defined(CONFIG_NETUS_SERIALS) || defined(CONFIG_NETUS_FOXGM)
-	/* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
-	at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
-			   | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
-			   | ATMEL_UART_RI);
-
-	/* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */
-	at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS);
-#endif
-
-#if defined(CONFIG_NETUS_SERIALS)
-	/* USART2 on ttyS3. (Rx, Tx) */
-	at91_register_uart(AT91SAM9260_ID_US2, 3, 0);
-#endif
-
-	/* set serial console to ttyS0 (ie, DBGU) */
-	at91_set_serial_console(0);
-}
-
-static void __init ek_init_irq(void)
-{
-	at91sam9260_init_interrupts(NULL);
-}
-
-
-/*
- * USB Host port
- */
-static struct at91_usbh_data __initdata ek_usbh_data = {
-	.ports		= 2,
-};
-
-/*
- * USB Device port
- */
-static struct at91_udc_data __initdata ek_udc_data = {
-	.vbus_pin	= AT91_PIN_PC6,
-	.pullup_pin	= 0,		/* pull-up driven by UDC */
-};
-
-
-/*
- * SPI devices.
- */
-static struct spi_board_info ek_spi_devices[] = {
-#if defined(CONFIG_NETUS_USE_DATAFLASH)
-	{	/* DataFlash chip */
-		.modalias	= "mtd_dataflash",
-		.chip_select	= 1,
-		.max_speed_hz	= 15 * 1000 * 1000,
-		.bus_num	= 0,
-	},
-#endif
-};
-
-
-/*
- * MACB Ethernet device
- */
-static struct at91_eth_data __initdata ek_macb_data = {
-	.phy_irq_pin	= AT91_PIN_PA29,
-	.is_rmii	= 1,
-};
-
-
-/*
- * MCI (SD/MMC)
- * det_pin, wp_pin and vcc_pin are not connected
- */
-static struct at91_mmc_data __initdata ek_mmc_data = {
-	.slot_b		= 1,
-	.wire4		= 1,
-};
-
-/*
- * LEDs
- */
-static struct gpio_led ek_leds[] = {
-#if defined(CONFIG_NETUS_FOXGM)
-	{
-		.name			= "led:red:L4",
-		.gpio			= AT91_PIN_PC9,
-		.active_low		= 0,
-		.default_trigger	= "heartbeat",
-	},
-	{
-		.name			= "led:red:L5",
-		.gpio			= AT91_PIN_PC13,
-		.active_low		= 0,
-		.default_trigger	= "none",
-	},
-#endif		//CONFIG_NETUS_FOXGM
-	{
-		.name			= "led:red:user",
-		.gpio			= AT91_PIN_PC7,
-		.active_low		= 0,
-#if defined(CONFIG_NETUS_HEARTBEAT_LED)
-		.default_trigger	= "heartbeat",
-#else
-		.default_trigger	= "none",
-#endif		//CONFIG_NETUS_HEARTBEAT_LED
-	},
-};
-
-/*
- * GPIO Buttons
- */
-#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
-
-static struct gpio_keys_button ek_buttons[] = {
-	{
-		.gpio		= AT91_PIN_PC4,
-		.code		= BTN_1,
-		.desc		= "Button 1",
-		.active_low	= 1,
-		.wakeup		= 1,
-	},
-};
-
-static struct gpio_keys_platform_data ek_button_data = {
-	.buttons	= ek_buttons,
-	.nbuttons	= ARRAY_SIZE(ek_buttons),
-};
-
-static struct platform_device ek_button_device = {
-	.name		= "gpio-keys",
-	.id		= -1,
-	.num_resources	= 0,
-	.dev		= {
-		.platform_data	= &ek_button_data,
-	}
-};
-
-static void __init ek_add_device_buttons(void)
-{
-	at91_set_gpio_input(AT91_PIN_PC4, 1);	/* btn1 */
-	at91_set_deglitch(AT91_PIN_PC4, 1);
-
-	platform_device_register(&ek_button_device);
-}
-#else
-static void __init ek_add_device_buttons(void) {}
-#endif
-
-static struct resource gpiodev_resource = { 
-	        .start                  = 0xFFFFFFFF, 
-}; 
-
-static void __init ek_board_init(void)
-{
-	/* Serial */
-	at91_add_device_serial();
-	/* USB Host */
-	at91_add_device_usbh(&ek_usbh_data);
-	/* USB Device */
-	at91_add_device_udc(&ek_udc_data);
-	/* SPI */
-	at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices));
-	/* Ethernet */
-	at91_add_device_eth(&ek_macb_data);
-	/* MMC */
-	at91_add_device_mmc(0, &ek_mmc_data);
-	/* I2C */
-	at91_add_device_i2c(NULL, 0);
-	/* LEDs */
-	at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds));
-	/* Push Buttons */
-	ek_add_device_buttons();
-	/* Register GPIODEV */ 
-	platform_device_register_simple("GPIODEV", 0, &gpiodev_resource, 1); 
-
-}
-
-MACHINE_START(AT91SAM9G20EK, "Acmesystems Netus FoxBoardG20")
-	/* Maintainer: Claudio Mignanti */
-	.phys_io	= AT91_BASE_SYS,
-	.io_pg_offst	= (AT91_VA_BASE_SYS >> 18) & 0xfffc,
-	.boot_params	= AT91_SDRAM_BASE + 0x100,
-	.timer		= &at91sam926x_timer,
-	.map_io		= ek_map_io,
-	.init_irq	= ek_init_irq,
-	.init_machine	= ek_board_init,
-MACHINE_END
-
-