removed the old directories, too.. cleanup is ready, yay

git-svn-id: svn://svn.openwrt.org/openwrt/trunk@2130 3c298f89-4303-0410-b956-a3cf2f4a3e73

2 files changed, 0 insertions, 131 deletions

diff --git a/obsolete-buildroot/sources/openwrt/ipkg/dhcp-fwd/root/etc/dhcp-fwd.conf b/obsolete-buildroot/sources/openwrt/ipkg/dhcp-fwd/root/etc/dhcp-fwd.conf
deleted file mode 100644
index 15514e388..000000000
--- a/obsolete-buildroot/sources/openwrt/ipkg/dhcp-fwd/root/etc/dhcp-fwd.conf
+++ /dev/null
@@ -1,114 +0,0 @@
-## $Id$
-
-## This file contains a sample configuration for the network shown
-## below:
-##
-##  --------------              ----------              -------------
-## |  DHCP Server |            |          |            |             |
-## | 192.168.8.66 |------<eth1>| dhcp-fwd |<eth2>------|   Clients   |
-## |              |            |          |            |             |
-##  --------------              ----------              -------------
-##  
-## By default, the dhcp-fwd agent looks at /etc/dhcp-fwd.conf
-## for this file. By using the '-c' option when calling dhcp-fwd, this
-## path can be changed.
-
-
-######### ENVIRONMENT SETTINGS #########
-####
-###
-## The server will drop its privileges and goes into a chroot-jail
-## after doing its initialization. The following parameters are
-## defining the needed parameters:
-
-## User and group names/ids. It can be a numeric id or a resolvable
-## alphanumeric-name.
-##
-## WARNING: when compiled with dietlibc the user-/group-names must be
-##          resolvable by files-NSS. LDAP or NIS NSS will not work so
-##          the numeric ids must be used
-user		daemon
-group		daemon
-
-## chroot() path
-chroot		/var/run/dhcp-fwd
-
-## Logfile and loglevel. The logfile-location is relatively to the
-## directory where dhcp-fwd was started and not to the chroot-directory.
-##
-## The loglevel option is not supported yet.
-logfile		/var/log/dhcp-fwd.log
-loglevel	1
-
-## SysV pidfile; contains the PID of the daemon-process and will be
-## written with root-privileges
-pidfile		/var/run/dhcp-fwd.pid
-
-
-## Set limit for resources. When using much interfaces or servers
-## below you will need to increase some values. Same holds when not
-## using dietlibc. Use '-1' as the value to disable the upper limit
-## for the given resource.
-##
-## Look into /proc/<pid>/status to find out the real usage of the
-## resources.
-ulimit core	0
-ulimit stack	64K
-ulimit data	32K
-ulimit rss	200K
-ulimit nproc	0
-ulimit nofile	0
-ulimit as	0
-
-
-######### INTERFACE SETTINGS #########
-####
-###
-## The interface where the forwarder listens for messages. There must
-## be specified BOTH the server-side and client-side interfaces!
-##
-## Each interface will be identified by its system-wide name
-## (e.g. eth0). After this it must be told whether there are
-## clients and servers, and if it is allowed to send broadcast
-## messages to clients. The bcast flags will be IGNORED when
-## forwarding messages to servers.
-
-#	IFNAME	clients	servers bcast
-if	eth2	true	false	true
-if	eth1	false	true	true
-
-
-## Each interface can be given an RFC 3046 agent ID. The 'name' config
-## option sets this value; if an interface is not specified here, the
-## IFNAME will be assumed.
-
-#	IFNAME	agent-id
-name	eth2	ws-c
-
-
-## Each interface can be given an specific IP to be filled into the
-## 'giaddr' field.
-##
-## BEWARE: because the outgoing DHCP message will contain the "normal" IP
-## address of the outgoing-interface in its IP-header, some additional
-## work in the system must be done. You can e.g. add an iptables rule to
-## the 'nat' table similarly to this:
-##
-## | Chain POSTROUTING (policy ACCEPT)
-## | target     prot opt source               destination         
-## | SNAT       udp  --  192.168.0.6          192.168.8.66       udp spt:68 dpt:67 to:192.168.2.255 
-
-# ip	eth0	192.168.2.255
-
-
-######### SERVER SETTINGS #########
-####
-###
-## Definitions of the servers. There must be told the type ('ip' or
-## 'bcast') and the address. When using 'ip', the address is a non-bcast
-## IPv4 address (dotted, DNS-names are NOT supported); and when using
-## 'bcast' servers, the address is an IFNAME.
-
-#	TYPE	address
-server	ip	192.168.8.66
-#server	bcast	eth1
diff --git a/obsolete-buildroot/sources/openwrt/ipkg/dhcp-fwd/root/etc/init.d/dhcp-fwd b/obsolete-buildroot/sources/openwrt/ipkg/dhcp-fwd/root/etc/init.d/dhcp-fwd
deleted file mode 100644
index 597e1fc78..000000000
--- a/obsolete-buildroot/sources/openwrt/ipkg/dhcp-fwd/root/etc/init.d/dhcp-fwd
+++ /dev/null
@@ -1,17 +0,0 @@
-#!/bin/sh
-
-case $1 in
- start)
-  [ -d /var/log ] || mkdir -p /var/log
-  [ -d /var/run/dhcp-wfd ] || mkdir -p /var/run/dhcp-fwd
-  dhcp-fwd
-  ;;
- stop)
-  [ -f /var/run/dhcpd-fwd.pid ] && kill $(cat /var/run/dhcpd-fwd.pid) 2>/dev/null
-  ;;
- *)
-  echo "usage: $0 (start|stop)"
-  exit 1
-esac
-
-exit $?