Added support for the D-Link DSM-G600 RevA, and fixed the clock frequency for NSLU2 and DSMG600. Had to refresh the gateway 7001 patch due to changes in the file being patched.

git-svn-id: svn://svn.openwrt.org/openwrt/trunk@7770 3c298f89-4303-0410-b956-a3cf2f4a3e73

5 files changed, 742 insertions, 3 deletions

diff --git a/scripts/arm-magic.sh b/scripts/arm-magic.sh
index ee8a0bc1c..cfd559ed7 100755
--- a/scripts/arm-magic.sh
+++ b/scripts/arm-magic.sh
@@ -22,7 +22,7 @@
 # NOTE: for now it's for only IXP4xx in big endian mode
 
 # list of supported boards, in "boardname machtypeid" format
-for board in "avila 526" "gateway7001 731" "nslu2 597" "nas100d 865" "wg302v2 890" "pronghornmetro 1040" "compex 1273" "wrt300nv2 1077" "loft 849"
+for board in "avila 526" "gateway7001 731" "nslu2 597" "nas100d 865" "wg302v2 890" "pronghornmetro 1040" "compex 1273" "wrt300nv2 1077" "loft 849" "dsmg600 964"
 do
   set -- $board
   hexid=$(printf %x\\n $2)
diff --git a/target/linux/ixp4xx-2.6/patches/050-dsmg600_upstream_support.patch b/target/linux/ixp4xx-2.6/patches/050-dsmg600_upstream_support.patch
new file mode 100644
index 000000000..b214ef2b5
--- /dev/null
+++ b/target/linux/ixp4xx-2.6/patches/050-dsmg600_upstream_support.patch
@@ -0,0 +1,551 @@
+This patch adds support for the D-Link DSM-G600 Rev A.
+This is an ARM XScale IXP4xx system relatively similar to
+the NSLU2 and NAS-100D already supported by mainline. An
+important difference is Gigabit Ethernet support using
+the Via Velocity chipset.
+
+This patch is the combined work of Michael Westerhof and
+Alessandro Zummo, with contributions from Michael-Luke
+Jones. This version addresses review comments from rmk
+and Deepak Saxena.
+
+Signed-off-by: Michael-Luke Jones <mlj28@cam.ac.uk>
+Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
+Signed-off-by: Michael Westerhof <mwester@dls.net>
+
+---
+ arch/arm/mach-ixp4xx/Kconfig           |    9 +
+ arch/arm/mach-ixp4xx/Makefile          |    2 
+ arch/arm/mach-ixp4xx/dsmg600-pci.c     |   74 +++++++++++++
+ arch/arm/mach-ixp4xx/dsmg600-power.c   |  130 ++++++++++++++++++++++++
+ arch/arm/mach-ixp4xx/dsmg600-setup.c   |  175 +++++++++++++++++++++++++++++++++
+ include/asm-arm/arch-ixp4xx/dsmg600.h  |   57 ++++++++++
+ include/asm-arm/arch-ixp4xx/hardware.h |    1 
+ include/asm-arm/arch-ixp4xx/irqs.h     |   10 +
+ 8 files changed, 458 insertions(+)
+
+Index: linux-2.6.21.1-armeb/arch/arm/mach-ixp4xx/Kconfig
+===================================================================
+--- linux-2.6.21.1-armeb.orig/arch/arm/mach-ixp4xx/Kconfig
++++ linux-2.6.21.1-armeb/arch/arm/mach-ixp4xx/Kconfig
+@@ -89,6 +89,15 @@
+ 	  NAS 100d device. For more information on this platform,
+ 	  see http://www.nslu2-linux.org/wiki/NAS100d/HomePage
+ 
++config MACH_DSMG600
++	bool
++	prompt "D-Link DSM-G600 RevA"
++	select PCI
++	help
++	  Say 'Y' here if you want your kernel to support D-Link's
++	  DSM-G600 RevA device. For more information on this platform,
++	  see http://www.nslu2-linux.org/wiki/DSMG600/HomePage
++
+ #
+ # Avila and IXDP share the same source for now. Will change in future
+ #
+Index: linux-2.6.21.1-armeb/arch/arm/mach-ixp4xx/Makefile
+===================================================================
+--- linux-2.6.21.1-armeb.orig/arch/arm/mach-ixp4xx/Makefile
++++ linux-2.6.21.1-armeb/arch/arm/mach-ixp4xx/Makefile
+@@ -12,6 +12,7 @@
+ obj-pci-$(CONFIG_MACH_GTWX5715)		+= gtwx5715-pci.o
+ obj-pci-$(CONFIG_MACH_NSLU2)		+= nslu2-pci.o
+ obj-pci-$(CONFIG_MACH_NAS100D)		+= nas100d-pci.o
++obj-pci-$(CONFIG_MACH_DSMG600)		+= dsmg600-pci.o
+ 
+ obj-y	+= common.o
+ 
+@@ -22,5 +23,6 @@
+ obj-$(CONFIG_MACH_GTWX5715)	+= gtwx5715-setup.o
+ obj-$(CONFIG_MACH_NSLU2)	+= nslu2-setup.o nslu2-power.o
+ obj-$(CONFIG_MACH_NAS100D)	+= nas100d-setup.o nas100d-power.o
++obj-$(CONFIG_MACH_DSMG600)      += dsmg600-setup.o dsmg600-power.o
+ 
+ obj-$(CONFIG_PCI)		+= $(obj-pci-$(CONFIG_PCI)) common-pci.o
+Index: linux-2.6.21.1-armeb/arch/arm/mach-ixp4xx/dsmg600-pci.c
+===================================================================
+--- /dev/null
++++ linux-2.6.21.1-armeb/arch/arm/mach-ixp4xx/dsmg600-pci.c
+@@ -0,0 +1,74 @@
++/*
++ * DSM-G600 board-level PCI initialization
++ *
++ * Copyright (C) 2006 Tower Technologies
++ * Author: Alessandro Zummo <a.zummo@towertech.it>
++ *
++ * based on ixdp425-pci.c:
++ *	Copyright (C) 2002 Intel Corporation.
++ *	Copyright (C) 2003-2004 MontaVista Software, Inc.
++ *
++ * Maintainer: http://www.nslu2-linux.org/
++ *
++ * This program is free software; you can redistribute it and/or modify
++ * it under the terms of the GNU General Public License version 2 as
++ * published by the Free Software Foundation.
++ *
++ */
++
++#include <linux/pci.h>
++#include <linux/init.h>
++#include <linux/irq.h>
++
++#include <asm/mach/pci.h>
++#include <asm/mach-types.h>
++
++void __init dsmg600_pci_preinit(void)
++{
++	set_irq_type(IRQ_DSMG600_PCI_INTA, IRQT_LOW);
++	set_irq_type(IRQ_DSMG600_PCI_INTB, IRQT_LOW);
++	set_irq_type(IRQ_DSMG600_PCI_INTC, IRQT_LOW);
++	set_irq_type(IRQ_DSMG600_PCI_INTD, IRQT_LOW);
++	set_irq_type(IRQ_DSMG600_PCI_INTE, IRQT_LOW);
++	set_irq_type(IRQ_DSMG600_PCI_INTF, IRQT_LOW);
++
++	ixp4xx_pci_preinit();
++}
++
++static int __init dsmg600_map_irq(struct pci_dev *dev, u8 slot, u8 pin)
++{
++	static int pci_irq_table[DSMG600_PCI_MAX_DEV][DSMG600_PCI_IRQ_LINES] =
++	{
++		{ IRQ_DSMG600_PCI_INTE, -1, -1 },
++		{ IRQ_DSMG600_PCI_INTA, -1, -1 },
++		{ IRQ_DSMG600_PCI_INTB, IRQ_DSMG600_PCI_INTC, IRQ_DSMG600_PCI_INTD },
++		{ IRQ_DSMG600_PCI_INTF, -1, -1 },
++	};
++
++	int irq = -1;
++
++	if (slot >= 1 && slot <= DSMG600_PCI_MAX_DEV &&
++		pin >= 1 && pin <= DSMG600_PCI_IRQ_LINES)
++		irq = pci_irq_table[slot-1][pin-1];
++
++	return irq;
++}
++
++struct hw_pci __initdata dsmg600_pci = {
++	.nr_controllers = 1,
++	.preinit	= dsmg600_pci_preinit,
++	.swizzle	= pci_std_swizzle,
++	.setup		= ixp4xx_setup,
++	.scan		= ixp4xx_scan_bus,
++	.map_irq	= dsmg600_map_irq,
++};
++
++int __init dsmg600_pci_init(void)
++{
++	if (machine_is_dsmg600())
++		pci_common_init(&dsmg600_pci);
++
++	return 0;
++}
++
++subsys_initcall(dsmg600_pci_init);
+Index: linux-2.6.21.1-armeb/arch/arm/mach-ixp4xx/dsmg600-power.c
+===================================================================
+--- /dev/null
++++ linux-2.6.21.1-armeb/arch/arm/mach-ixp4xx/dsmg600-power.c
+@@ -0,0 +1,130 @@
++/*
++ * arch/arm/mach-ixp4xx/dsmg600-power.c
++ *
++ * DSM-G600 Power/Reset driver
++ * Author: Michael Westerhof <mwester@dls.net>
++ *
++ * Based on nslu2-power.c
++ *  Copyright (C) 2005 Tower Technologies
++ *  Author: Alessandro Zummo <a.zummo@towertech.it>
++ *
++ * which was based on nslu2-io.c
++ *  Copyright (C) 2004 Karen Spearel
++ *
++ * Maintainers: http://www.nslu2-linux.org/
++ *
++ * This program is free software; you can redistribute it and/or modify
++ * it under the terms of the GNU General Public License version 2 as
++ * published by the Free Software Foundation.
++ *
++ */
++
++#include <linux/module.h>
++#include <linux/reboot.h>
++#include <linux/interrupt.h>
++#include <linux/irq.h>
++#include <linux/jiffies.h>
++#include <linux/timer.h>
++
++#include <asm/mach-types.h>
++
++extern void ctrl_alt_del(void);
++
++/* This is used to make sure the power-button pusher is serious.  The button
++ * must be held until the value of this counter reaches zero.
++ */
++static volatile int power_button_countdown;
++
++/* Must hold the button down for at least this many counts to be processed */
++#define PBUTTON_HOLDDOWN_COUNT 4 /* 2 secs */
++
++static void dsmg600_power_handler(unsigned long data);
++static DEFINE_TIMER(dsmg600_power_timer, dsmg600_power_handler, 0, 0);
++
++static void dsmg600_power_handler(unsigned long data)
++{
++	/* This routine is called twice per second to check the
++	 * state of the power button.
++	 */
++
++	if (*IXP4XX_GPIO_GPINR & DSMG600_PB_BM) {
++
++		/* IO Pin is 1 (button pushed) */
++		if (power_button_countdown > 0) {
++			power_button_countdown--;
++		}
++
++	} else {
++
++		/* Done on button release, to allow for auto-power-on mods. */
++		if (power_button_countdown == 0) {
++			/* Signal init to do the ctrlaltdel action, this will bypass
++			 * init if it hasn't started and do a kernel_restart.
++			 */
++			ctrl_alt_del();
++
++			/* Change the state of the power LED to "blink" */
++			gpio_line_set(DSMG600_LED_PWR_GPIO, IXP4XX_GPIO_LOW);
++		} else {
++			power_button_countdown = PBUTTON_HOLDDOWN_COUNT;
++		}
++	}
++
++	mod_timer(&dsmg600_power_timer, jiffies + msecs_to_jiffies(500));
++}
++
++static irqreturn_t dsmg600_reset_handler(int irq, void *dev_id)
++{
++	/* This is the paper-clip reset, it shuts the machine down directly. */
++	machine_power_off();
++
++	return IRQ_HANDLED;
++}
++
++static int __init dsmg600_power_init(void)
++{
++	if (!(machine_is_dsmg600()))
++		return 0;
++
++	if (request_irq(DSMG600_RB_IRQ, &dsmg600_reset_handler,
++		IRQF_DISABLED | IRQF_TRIGGER_LOW, "DSM-G600 reset button",
++		NULL) < 0) {
++
++		printk(KERN_DEBUG "Reset Button IRQ %d not available\n",
++			DSMG600_RB_IRQ);
++
++		return -EIO;
++	}
++
++	/* The power button on the D-Link DSM-G600 is on GPIO 15, but
++	 * it cannot handle interrupts on that GPIO line.  So we'll
++	 * have to poll it with a kernel timer.
++	 */
++
++	/* Make sure that the power button GPIO is set up as an input */
++	gpio_line_config(DSMG600_PB_GPIO, IXP4XX_GPIO_IN);
++
++	/* Set the initial value for the power button IRQ handler */
++	power_button_countdown = PBUTTON_HOLDDOWN_COUNT;
++
++	mod_timer(&dsmg600_power_timer, jiffies + msecs_to_jiffies(500));
++
++	return 0;
++}
++
++static void __exit dsmg600_power_exit(void)
++{
++	if (!(machine_is_dsmg600()))
++		return;
++
++	del_timer_sync(&dsmg600_power_timer);
++
++	free_irq(DSMG600_RB_IRQ, NULL);
++}
++
++module_init(dsmg600_power_init);
++module_exit(dsmg600_power_exit);
++
++MODULE_AUTHOR("Michael Westerhof <mwester@dls.net>");
++MODULE_DESCRIPTION("DSM-G600 Power/Reset driver");
++MODULE_LICENSE("GPL");
+Index: linux-2.6.21.1-armeb/arch/arm/mach-ixp4xx/dsmg600-setup.c
+===================================================================
+--- /dev/null
++++ linux-2.6.21.1-armeb/arch/arm/mach-ixp4xx/dsmg600-setup.c
+@@ -0,0 +1,175 @@
++/*
++ * DSM-G600 board-setup
++ *
++ * Copyright (C) 2006 Tower Technologies
++ * Author: Alessandro Zummo <a.zummo@towertech.it>
++ *
++ * based ixdp425-setup.c:
++ *      Copyright (C) 2003-2004 MontaVista Software, Inc.
++ *
++ * Author: Alessandro Zummo <a.zummo@towertech.it>
++ * Maintainers: http://www.nslu2-linux.org/
++ */
++
++#include <linux/kernel.h>
++#include <linux/serial.h>
++#include <linux/serial_8250.h>
++
++#include <asm/mach-types.h>
++#include <asm/mach/arch.h>
++#include <asm/mach/flash.h>
++
++static struct flash_platform_data dsmg600_flash_data = {
++	.map_name		= "cfi_probe",
++	.width			= 2,
++};
++
++static struct resource dsmg600_flash_resource = {
++	.flags			= IORESOURCE_MEM,
++};
++
++static struct platform_device dsmg600_flash = {
++	.name			= "IXP4XX-Flash",
++	.id			= 0,
++	.dev.platform_data	= &dsmg600_flash_data,
++	.num_resources		= 1,
++	.resource		= &dsmg600_flash_resource,
++};
++
++static struct ixp4xx_i2c_pins dsmg600_i2c_gpio_pins = {
++	.sda_pin		= DSMG600_SDA_PIN,
++	.scl_pin		= DSMG600_SCL_PIN,
++};
++
++static struct platform_device dsmg600_i2c_controller = {
++	.name			= "IXP4XX-I2C",
++	.id			= 0,
++	.dev.platform_data	= &dsmg600_i2c_gpio_pins,
++};
++
++#ifdef CONFIG_LEDS_CLASS
++static struct resource dsmg600_led_resources[] = {
++	{
++		.name           = "power",
++		.start          = DSMG600_LED_PWR_GPIO,
++		.end            = DSMG600_LED_PWR_GPIO,
++		.flags          = IXP4XX_GPIO_HIGH,
++	},
++	{
++		.name           = "wlan",
++		.start		= DSMG600_LED_WLAN_GPIO,
++		.end            = DSMG600_LED_WLAN_GPIO,
++		.flags          = IXP4XX_GPIO_LOW,
++	},
++};
++
++static struct platform_device dsmg600_leds = {
++        .name                   = "IXP4XX-GPIO-LED",
++        .id                     = -1,
++        .num_resources          = ARRAY_SIZE(dsmg600_led_resources),
++        .resource               = dsmg600_led_resources,
++};
++#endif
++
++static struct resource dsmg600_uart_resources[] = {
++	{
++		.start		= IXP4XX_UART1_BASE_PHYS,
++		.end		= IXP4XX_UART1_BASE_PHYS + 0x0fff,
++		.flags		= IORESOURCE_MEM,
++	},
++	{
++		.start		= IXP4XX_UART2_BASE_PHYS,
++		.end		= IXP4XX_UART2_BASE_PHYS + 0x0fff,
++		.flags		= IORESOURCE_MEM,
++	}
++};
++
++static struct plat_serial8250_port dsmg600_uart_data[] = {
++	{
++		.mapbase	= IXP4XX_UART1_BASE_PHYS,
++		.membase	= (char *)IXP4XX_UART1_BASE_VIRT + REG_OFFSET,
++		.irq		= IRQ_IXP4XX_UART1,
++		.flags		= UPF_BOOT_AUTOCONF,
++		.iotype		= UPIO_MEM,
++		.regshift	= 2,
++		.uartclk	= IXP4XX_UART_XTAL,
++	},
++	{
++		.mapbase	= IXP4XX_UART2_BASE_PHYS,
++		.membase	= (char *)IXP4XX_UART2_BASE_VIRT + REG_OFFSET,
++		.irq		= IRQ_IXP4XX_UART2,
++		.flags		= UPF_BOOT_AUTOCONF,
++		.iotype		= UPIO_MEM,
++		.regshift	= 2,
++		.uartclk	= IXP4XX_UART_XTAL,
++	},
++	{ }
++};
++
++static struct platform_device dsmg600_uart = {
++	.name			= "serial8250",
++	.id			= PLAT8250_DEV_PLATFORM,
++	.dev.platform_data	= dsmg600_uart_data,
++	.num_resources		= ARRAY_SIZE(dsmg600_uart_resources),
++	.resource		= dsmg600_uart_resources,
++};
++
++static struct platform_device *dsmg600_devices[] __initdata = {
++	&dsmg600_i2c_controller,
++	&dsmg600_flash,
++};
++
++static void dsmg600_power_off(void)
++{
++	/* enable the pwr cntl gpio */
++	gpio_line_config(DSMG600_PO_GPIO, IXP4XX_GPIO_OUT);
++
++	/* poweroff */
++	gpio_line_set(DSMG600_PO_GPIO, IXP4XX_GPIO_HIGH);
++}
++
++static void __init dsmg600_init(void)
++{
++	ixp4xx_sys_init();
++
++	/* Make sure that GPIO14 and GPIO15 are not used as clocks */
++	*IXP4XX_GPIO_GPCLKR = 0;
++
++	dsmg600_flash_resource.start = IXP4XX_EXP_BUS_BASE(0);
++	dsmg600_flash_resource.end =
++		IXP4XX_EXP_BUS_BASE(0) + ixp4xx_exp_bus_size - 1;
++
++	pm_power_off = dsmg600_power_off;
++
++	/* The UART is required on the DSM-G600 (Redboot cannot use the
++	 * NIC) -- do it here so that it does *not* get removed if
++	 * platform_add_devices fails!
++         */
++        (void)platform_device_register(&dsmg600_uart);
++
++	platform_add_devices(dsmg600_devices, ARRAY_SIZE(dsmg600_devices));
++
++#ifdef CONFIG_LEDS_CLASS
++        /* We don't care whether or not this works. */
++        (void)platform_device_register(&dsmg600_leds);
++#endif
++}
++
++static void __init dsmg600_fixup(struct machine_desc *desc,
++                struct tag *tags, char **cmdline, struct meminfo *mi)
++{
++       /* The xtal on this machine is non-standard. */
++        ixp4xx_timer_freq = DSMG600_FREQ;
++}
++
++MACHINE_START(DSMG600, "D-Link DSM-G600 RevA")
++	/* Maintainer: www.nslu2-linux.org */
++	.phys_io	= IXP4XX_PERIPHERAL_BASE_PHYS,
++	.io_pg_offst	= ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xFFFC,
++	.boot_params	= 0x00000100,
++	.fixup          = dsmg600_fixup,
++	.map_io		= ixp4xx_map_io,
++	.init_irq	= ixp4xx_init_irq,
++	.timer          = &ixp4xx_timer,
++	.init_machine	= dsmg600_init,
++MACHINE_END
+Index: linux-2.6.21.1-armeb/include/asm-arm/arch-ixp4xx/dsmg600.h
+===================================================================
+--- /dev/null
++++ linux-2.6.21.1-armeb/include/asm-arm/arch-ixp4xx/dsmg600.h
+@@ -0,0 +1,57 @@
++/*
++ * DSM-G600 platform specific definitions
++ *
++ * Copyright (C) 2006 Tower Technologies
++ * Author: Alessandro Zummo <a.zummo@towertech.it>
++ *
++ * based on ixdp425.h:
++ *	Copyright 2004 (C) MontaVista, Software, Inc.
++ *
++ * This file is licensed under  the terms of the GNU General Public
++ * License version 2. This program is licensed "as is" without any
++ * warranty of any kind, whether express or implied.
++ */
++
++#ifndef __ASM_ARCH_HARDWARE_H__
++#error "Do not include this directly, instead #include <asm/hardware.h>"
++#endif
++
++#define DSMG600_SDA_PIN		5
++#define DSMG600_SCL_PIN		4
++
++/*
++ * DSMG600 PCI IRQs
++ */
++#define DSMG600_PCI_MAX_DEV	4
++#define DSMG600_PCI_IRQ_LINES	3
++
++
++/* PCI controller GPIO to IRQ pin mappings */
++#define DSMG600_PCI_INTA_PIN	11
++#define DSMG600_PCI_INTB_PIN	10
++#define DSMG600_PCI_INTC_PIN	9
++#define DSMG600_PCI_INTD_PIN	8
++#define DSMG600_PCI_INTE_PIN	7
++#define DSMG600_PCI_INTF_PIN	6
++
++/* DSM-G600 Timer Setting */
++#define DSMG600_FREQ 66000000
++
++/* Buttons */
++
++#define DSMG600_PB_GPIO		15	/* power button */
++#define DSMG600_PB_BM		(1L << DSMG600_PB_GPIO)
++
++#define DSMG600_RB_GPIO		3	/* reset button */
++
++#define DSMG600_RB_IRQ		IRQ_IXP4XX_GPIO3
++
++#define DSMG600_PO_GPIO		2	/* power off */
++
++/* LEDs */
++
++#define DSMG600_LED_PWR_GPIO	0
++#define DSMG600_LED_PWR_BM	(1L << DSMG600_LED_PWR_GPIO)
++
++#define DSMG600_LED_WLAN_GPIO	14
++#define DSMG600_LED_WLAN_BM	(1L << DSMG600_LED_WLAN_GPIO)
+Index: linux-2.6.21.1-armeb/include/asm-arm/arch-ixp4xx/hardware.h
+===================================================================
+--- linux-2.6.21.1-armeb.orig/include/asm-arm/arch-ixp4xx/hardware.h
++++ linux-2.6.21.1-armeb/include/asm-arm/arch-ixp4xx/hardware.h
+@@ -47,5 +47,6 @@
+ #include "prpmc1100.h"
+ #include "nslu2.h"
+ #include "nas100d.h"
++#include "dsmg600.h"
+ 
+ #endif  /* _ASM_ARCH_HARDWARE_H */
+Index: linux-2.6.21.1-armeb/include/asm-arm/arch-ixp4xx/irqs.h
+===================================================================
+--- linux-2.6.21.1-armeb.orig/include/asm-arm/arch-ixp4xx/irqs.h
++++ linux-2.6.21.1-armeb/include/asm-arm/arch-ixp4xx/irqs.h
+@@ -118,4 +118,14 @@
+ #define        IRQ_NAS100D_PCI_INTD    IRQ_IXP4XX_GPIO8
+ #define        IRQ_NAS100D_PCI_INTE    IRQ_IXP4XX_GPIO7
+ 
++/*
++ * D-Link DSM-G600 RevA board IRQs
++ */
++#define        IRQ_DSMG600_PCI_INTA    IRQ_IXP4XX_GPIO11
++#define        IRQ_DSMG600_PCI_INTB    IRQ_IXP4XX_GPIO10
++#define        IRQ_DSMG600_PCI_INTC    IRQ_IXP4XX_GPIO9
++#define        IRQ_DSMG600_PCI_INTD    IRQ_IXP4XX_GPIO8
++#define        IRQ_DSMG600_PCI_INTE    IRQ_IXP4XX_GPIO7
++#define        IRQ_DSMG600_PCI_INTF    IRQ_IXP4XX_GPIO6
++
+ #endif
diff --git a/target/linux/ixp4xx-2.6/patches/070-ixp4xx_freq_fixup.patch b/target/linux/ixp4xx-2.6/patches/070-ixp4xx_freq_fixup.patch
new file mode 100644
index 000000000..5b406a7bc
--- /dev/null
+++ b/target/linux/ixp4xx-2.6/patches/070-ixp4xx_freq_fixup.patch
@@ -0,0 +1,131 @@
+This patch is required as the frequency fixup in nslu2_init does not
+run sufficiently early in the boot sequence to take effect. In
+addition the dsmg600 setup code behaviour has been improved such
+that a 'fixup' routine is avoided.
+
+Signed-off-by: Michael-Luke Jones <mlj28@cam.ac.uk>
+
+Index: linux-2.6.21-arm/arch/arm/mach-ixp4xx/nslu2-setup.c
+===================================================================
+--- linux-2.6.21-arm.orig/arch/arm/mach-ixp4xx/nslu2-setup.c	2007-05-07 12:05:40.000000000 -0700
++++ linux-2.6.21-arm/arch/arm/mach-ixp4xx/nslu2-setup.c	2007-05-07 12:15:56.000000000 -0700
+@@ -22,6 +22,7 @@
+ #include <asm/mach-types.h>
+ #include <asm/mach/arch.h>
+ #include <asm/mach/flash.h>
++#include <asm/mach/time.h>
+ 
+ static struct flash_platform_data nslu2_flash_data = {
+ 	.map_name		= "cfi_probe",
+@@ -157,10 +158,21 @@
+ 	gpio_line_set(NSLU2_PO_GPIO, IXP4XX_GPIO_HIGH);
+ }
+ 
+-static void __init nslu2_init(void)
++static void __init nslu2_timer_init(void)
+ {
+-	ixp4xx_timer_freq = NSLU2_FREQ;
++    /* The xtal on this machine is non-standard. */
++    ixp4xx_timer_freq = NSLU2_FREQ;
++
++    /* Call standard timer_init function. */
++    ixp4xx_timer_init();
++}
+ 
++static struct sys_timer nslu2_timer = {
++    .init   = nslu2_timer_init,
++};
++
++static void __init nslu2_init(void)
++{
+ 	ixp4xx_sys_init();
+ 
+ 	nslu2_flash_resource.start = IXP4XX_EXP_BUS_BASE(0);
+@@ -185,6 +197,6 @@
+ 	.boot_params	= 0x00000100,
+ 	.map_io		= ixp4xx_map_io,
+ 	.init_irq	= ixp4xx_init_irq,
+-	.timer          = &ixp4xx_timer,
++	.timer          = &nslu2_timer,
+ 	.init_machine	= nslu2_init,
+ MACHINE_END
+Index: linux-2.6.21-arm/arch/arm/mach-ixp4xx/common.c
+===================================================================
+--- linux-2.6.21-arm.orig/arch/arm/mach-ixp4xx/common.c	2007-05-07 12:05:40.000000000 -0700
++++ linux-2.6.21-arm/arch/arm/mach-ixp4xx/common.c	2007-05-07 12:15:16.000000000 -0700
+@@ -269,7 +269,7 @@
+ 	.handler	= ixp4xx_timer_interrupt,
+ };
+ 
+-static void __init ixp4xx_timer_init(void)
++void __init ixp4xx_timer_init(void)
+ {
+ 	/* Clear Pending Interrupt by writing '1' to it */
+ 	*IXP4XX_OSST = IXP4XX_OSST_TIMER_1_PEND;
+Index: linux-2.6.21-arm/include/asm-arm/arch-ixp4xx/platform.h
+===================================================================
+--- linux-2.6.21-arm.orig/include/asm-arm/arch-ixp4xx/platform.h	2007-05-07 12:05:40.000000000 -0700
++++ linux-2.6.21-arm/include/asm-arm/arch-ixp4xx/platform.h	2007-05-07 12:15:16.000000000 -0700
+@@ -113,6 +113,7 @@
+ extern void ixp4xx_map_io(void);
+ extern void ixp4xx_init_irq(void);
+ extern void ixp4xx_sys_init(void);
++extern void ixp4xx_timer_init(void);
+ extern struct sys_timer ixp4xx_timer;
+ extern void ixp4xx_pci_preinit(void);
+ struct pci_sys_data;
+Index: linux-2.6.21-arm/arch/arm/mach-ixp4xx/dsmg600-setup.c
+===================================================================
+--- linux-2.6.21-arm.orig/arch/arm/mach-ixp4xx/dsmg600-setup.c	2007-05-07 12:05:42.000000000 -0700
++++ linux-2.6.21-arm/arch/arm/mach-ixp4xx/dsmg600-setup.c	2007-05-07 12:16:07.000000000 -0700
+@@ -18,6 +18,7 @@
+ #include <asm/mach-types.h>
+ #include <asm/mach/arch.h>
+ #include <asm/mach/flash.h>
++#include <asm/mach/time.h>
+ 
+ static struct flash_platform_data dsmg600_flash_data = {
+ 	.map_name		= "cfi_probe",
+@@ -128,6 +129,19 @@
+ 	gpio_line_set(DSMG600_PO_GPIO, IXP4XX_GPIO_HIGH);
+ }
+ 
++static void __init dsmg600_timer_init(void)
++{
++    /* The xtal on this machine is non-standard. */
++    ixp4xx_timer_freq = DSMG600_FREQ;
++
++    /* Call standard timer_init function. */
++    ixp4xx_timer_init();
++}
++
++static struct sys_timer dsmg600_timer = {
++    .init   = dsmg600_timer_init,
++};
++
+ static void __init dsmg600_init(void)
+ {
+ 	ixp4xx_sys_init();
+@@ -155,21 +169,13 @@
+ #endif
+ }
+ 
+-static void __init dsmg600_fixup(struct machine_desc *desc,
+-                struct tag *tags, char **cmdline, struct meminfo *mi)
+-{
+-       /* The xtal on this machine is non-standard. */
+-        ixp4xx_timer_freq = DSMG600_FREQ;
+-}
+-
+ MACHINE_START(DSMG600, "D-Link DSM-G600 RevA")
+ 	/* Maintainer: www.nslu2-linux.org */
+ 	.phys_io	= IXP4XX_PERIPHERAL_BASE_PHYS,
+ 	.io_pg_offst	= ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xFFFC,
+ 	.boot_params	= 0x00000100,
+-	.fixup          = dsmg600_fixup,
+ 	.map_io		= ixp4xx_map_io,
+ 	.init_irq	= ixp4xx_init_irq,
+-	.timer          = &ixp4xx_timer,
++	.timer          = &dsmg600_timer,
+ 	.init_machine	= dsmg600_init,
+ MACHINE_END
diff --git a/target/linux/ixp4xx-2.6/patches/187-dsmg600_rtc_fixup.patch b/target/linux/ixp4xx-2.6/patches/187-dsmg600_rtc_fixup.patch
new file mode 100644
index 000000000..04e51cd0c
--- /dev/null
+++ b/target/linux/ixp4xx-2.6/patches/187-dsmg600_rtc_fixup.patch
@@ -0,0 +1,57 @@
+Index: linux-2.6.21-arm/arch/arm/mach-ixp4xx/dsmg600-setup.c
+===================================================================
+--- linux-2.6.21-arm.orig/arch/arm/mach-ixp4xx/dsmg600-setup.c	2007-05-07 11:29:44.000000000 -0700
++++ linux-2.6.21-arm/arch/arm/mach-ixp4xx/dsmg600-setup.c	2007-05-07 11:31:15.000000000 -0700
+@@ -15,6 +15,7 @@
+ #include <linux/serial.h>
+ #include <linux/serial_8250.h>
+ 
++#include <asm/setup.h>
+ #include <asm/mach-types.h>
+ #include <asm/mach/arch.h>
+ #include <asm/mach/flash.h>
+@@ -142,6 +143,36 @@
+     .init   = dsmg600_timer_init,
+ };
+ 
++static char dsmg600_rtc_probe[] __initdata = "rtc-pcf8563.probe=0,0x51 ";
++
++static void __init dsmg600_fixup(struct machine_desc *desc,
++                struct tag *tags, char **cmdline, struct meminfo *mi)
++{
++    struct tag *t = tags;
++    char *p = *cmdline;
++
++    /* Find the end of the tags table, taking note of any cmdline tag. */
++    for (; t->hdr.size; t = tag_next(t)) {
++        if (t->hdr.tag == ATAG_CMDLINE) {
++            p = t->u.cmdline.cmdline;
++        }
++    }   
++
++    /* Overwrite the end of the table with a new cmdline tag. */
++    t->hdr.tag = ATAG_CMDLINE;
++    t->hdr.size =
++        (sizeof (struct tag_header) +
++        strlen(dsmg600_rtc_probe) + strlen(p) + 1 + 4) >> 2;
++    strlcpy(t->u.cmdline.cmdline, dsmg600_rtc_probe, COMMAND_LINE_SIZE);
++    strlcpy(t->u.cmdline.cmdline + strlen(dsmg600_rtc_probe), p,
++        COMMAND_LINE_SIZE - strlen(dsmg600_rtc_probe));
++
++    /* Terminate the table. */
++    t = tag_next(t);
++    t->hdr.tag = ATAG_NONE;
++    t->hdr.size = 0;
++}
++
+ static void __init dsmg600_init(void)
+ {
+ 	ixp4xx_sys_init();
+@@ -174,6 +205,7 @@
+ 	.phys_io	= IXP4XX_PERIPHERAL_BASE_PHYS,
+ 	.io_pg_offst	= ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xFFFC,
+ 	.boot_params	= 0x00000100,
++	.fixup		= dsmg600_fixup,
+ 	.map_io		= ixp4xx_map_io,
+ 	.init_irq	= ixp4xx_init_irq,
+ 	.timer          = &dsmg600_timer,
diff --git a/target/linux/ixp4xx-2.6/patches/200-gateway_7001.patch b/target/linux/ixp4xx-2.6/patches/200-gateway_7001.patch
index 8112bb889..80cf00079 100644
--- a/target/linux/ixp4xx-2.6/patches/200-gateway_7001.patch
+++ b/target/linux/ixp4xx-2.6/patches/200-gateway_7001.patch
@@ -219,17 +219,17 @@ diff -Nur linux-2.6.19.2/arch/arm/mach-ixp4xx/Makefile linux-2.6.19.2-owrt/arch/
 --- linux-2.6.19.2/arch/arm/mach-ixp4xx/Makefile	2007-01-10 20:10:37.000000000 +0100
 +++ linux-2.6.19.2-owrt/arch/arm/mach-ixp4xx/Makefile	2007-04-02 15:49:49.000000000 +0200
 @@ -11,6 +11,7 @@
- obj-pci-$(CONFIG_MACH_GTWX5715)		+= gtwx5715-pci.o
  obj-pci-$(CONFIG_MACH_NSLU2)		+= nslu2-pci.o
  obj-pci-$(CONFIG_MACH_NAS100D)		+= nas100d-pci.o
+ obj-pci-$(CONFIG_MACH_DSMG600)		+= dsmg600-pci.o
 +obj-pci-$(CONFIG_MACH_GATEWAY7001)	+= gateway7001-pci.o
  
  obj-y	+= common.o
  
 @@ -20,5 +21,6 @@
- obj-$(CONFIG_MACH_GTWX5715)	+= gtwx5715-setup.o
  obj-$(CONFIG_MACH_NSLU2)	+= nslu2-setup.o nslu2-power.o
  obj-$(CONFIG_MACH_NAS100D)	+= nas100d-setup.o nas100d-power.o
+ obj-$(CONFIG_MACH_DSMG600)      += dsmg600-setup.o dsmg600-power.o
 +obj-$(CONFIG_MACH_GATEWAY7001)	+= gateway7001-setup.o
  
  obj-$(CONFIG_PCI)		+= $(obj-pci-$(CONFIG_PCI)) common-pci.o