1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
|
From b11218c750ab92cfab4408a0328f1b36ceec3f33 Mon Sep 17 00:00:00 2001
From: Jonas Gorski <jonas.gorski@gmail.com>
Date: Fri, 6 Jan 2012 12:24:18 +0100
Subject: [PATCH 19/63] NET: bcm63xx_enet: move phy_(dis)connect into probe/remove
Only connect/disconnect the phy during probe and remove, not during any
open/close. The phy seldom changes during the runtime, and disconnecting
the phy during close will prevent it from keeping any configuration over
a down/up cycle.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
---
drivers/net/ethernet/broadcom/bcm63xx_enet.c | 84 +++++++++++++-------------
1 files changed, 41 insertions(+), 43 deletions(-)
--- a/drivers/net/ethernet/broadcom/bcm63xx_enet.c
+++ b/drivers/net/ethernet/broadcom/bcm63xx_enet.c
@@ -784,10 +784,8 @@ static int bcm_enet_open(struct net_devi
struct bcm_enet_priv *priv;
struct sockaddr addr;
struct device *kdev;
- struct phy_device *phydev;
int i, ret;
unsigned int size;
- char phy_id[MII_BUS_ID_SIZE + 3];
void *p;
u32 val;
@@ -795,40 +793,10 @@ static int bcm_enet_open(struct net_devi
kdev = &priv->pdev->dev;
if (priv->has_phy) {
- /* connect to PHY */
- snprintf(phy_id, sizeof(phy_id), PHY_ID_FMT,
- priv->mii_bus->id, priv->phy_id);
-
- phydev = phy_connect(dev, phy_id, bcm_enet_adjust_phy_link, 0,
- PHY_INTERFACE_MODE_MII);
-
- if (IS_ERR(phydev)) {
- dev_err(kdev, "could not attach to PHY\n");
- return PTR_ERR(phydev);
- }
-
- /* mask with MAC supported features */
- phydev->supported &= (SUPPORTED_10baseT_Half |
- SUPPORTED_10baseT_Full |
- SUPPORTED_100baseT_Half |
- SUPPORTED_100baseT_Full |
- SUPPORTED_Autoneg |
- SUPPORTED_Pause |
- SUPPORTED_MII);
- phydev->advertising = phydev->supported;
-
- if (priv->pause_auto && priv->pause_rx && priv->pause_tx)
- phydev->advertising |= SUPPORTED_Pause;
- else
- phydev->advertising &= ~SUPPORTED_Pause;
-
- dev_info(kdev, "attached PHY at address %d [%s]\n",
- phydev->addr, phydev->drv->name);
-
+ /* Reset state */
priv->old_link = 0;
priv->old_duplex = -1;
priv->old_pause = -1;
- priv->phydev = phydev;
}
/* mask all interrupts and request them */
@@ -838,7 +806,7 @@ static int bcm_enet_open(struct net_devi
ret = request_irq(dev->irq, bcm_enet_isr_mac, 0, dev->name, dev);
if (ret)
- goto out_phy_disconnect;
+ return ret;
ret = request_irq(priv->irq_rx, bcm_enet_isr_dma, IRQF_DISABLED,
dev->name, dev);
@@ -1025,9 +993,6 @@ out_freeirq_rx:
out_freeirq:
free_irq(dev->irq, dev);
-out_phy_disconnect:
- phy_disconnect(priv->phydev);
-
return ret;
}
@@ -1132,12 +1097,6 @@ static int bcm_enet_stop(struct net_devi
free_irq(priv->irq_rx, dev);
free_irq(dev->irq, dev);
- /* release phy */
- if (priv->has_phy) {
- phy_disconnect(priv->phydev);
- priv->phydev = NULL;
- }
-
return 0;
}
@@ -1714,6 +1673,8 @@ static int __devinit bcm_enet_probe(stru
/* MII bus registration */
if (priv->has_phy) {
+ struct phy_device *phydev;
+ char phy_id[MII_BUS_ID_SIZE + 3];
priv->mii_bus = mdiobus_alloc();
if (!priv->mii_bus) {
@@ -1750,6 +1711,38 @@ static int __devinit bcm_enet_probe(stru
dev_err(&pdev->dev, "unable to register mdio bus\n");
goto out_free_mdio;
}
+
+ /* connect to PHY */
+ snprintf(phy_id, sizeof(phy_id), PHY_ID_FMT,
+ priv->mii_bus->id, priv->phy_id);
+
+ phydev = phy_connect(dev, phy_id, bcm_enet_adjust_phy_link, 0,
+ PHY_INTERFACE_MODE_MII);
+
+ if (IS_ERR(phydev)) {
+ dev_err(&pdev->dev, "could not attach to PHY\n");
+ goto out_unregister_mdio;
+ }
+
+ /* mask with MAC supported features */
+ phydev->supported &= (SUPPORTED_10baseT_Half |
+ SUPPORTED_10baseT_Full |
+ SUPPORTED_100baseT_Half |
+ SUPPORTED_100baseT_Full |
+ SUPPORTED_Autoneg |
+ SUPPORTED_Pause |
+ SUPPORTED_MII);
+ phydev->advertising = phydev->supported;
+
+ if (priv->pause_auto && priv->pause_rx && priv->pause_tx)
+ phydev->advertising |= SUPPORTED_Pause;
+ else
+ phydev->advertising &= ~SUPPORTED_Pause;
+
+ dev_info(&pdev->dev, "attached PHY at address %d [%s]\n",
+ phydev->addr, phydev->drv->name);
+
+ priv->phydev = phydev;
} else {
/* run platform code to initialize PHY device */
@@ -1795,6 +1788,9 @@ static int __devinit bcm_enet_probe(stru
return 0;
out_unregister_mdio:
+ if (priv->phydev)
+ phy_disconnect(priv->phydev);
+
if (priv->mii_bus) {
mdiobus_unregister(priv->mii_bus);
kfree(priv->mii_bus->irq);
@@ -1845,6 +1841,8 @@ static int __devexit bcm_enet_remove(str
enet_writel(priv, 0, ENET_MIISC_REG);
if (priv->has_phy) {
+ phy_disconnect(priv->phydev);
+ priv->phydev = NULL;
mdiobus_unregister(priv->mii_bus);
kfree(priv->mii_bus->irq);
mdiobus_free(priv->mii_bus);
|
