1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
|
diff -urN linux-2.6.16.7/arch/mips/au1000/mtx-1/board_setup.c linux-2.6.16.7.new/arch/mips/au1000/mtx-1/board_setup.c
--- linux-2.6.16.7/arch/mips/au1000/mtx-1/board_setup.c 2006-04-23 14:39:21.000000000 +0200
+++ linux-2.6.16.7.new/arch/mips/au1000/mtx-1/board_setup.c 2006-04-23 14:39:03.000000000 +0200
@@ -44,6 +44,9 @@
#include <asm/pgtable.h>
#include <asm/mach-au1x00/au1000.h>
+extern int (*board_pci_idsel)(unsigned int devsel, int assert);
+int mtx1_pci_idsel(unsigned int devsel, int assert);
+
void board_reset (void)
{
/* Hit BCSR.SYSTEM_CONTROL[SW_RST] */
@@ -77,11 +80,37 @@
au_writel( 0xFFFFFFFF, SYS_TRIOUTCLR );
au_writel( 0x00000001, SYS_OUTPUTCLR ); // set M66EN (PCI 66MHz) to OFF
au_writel( 0x00000008, SYS_OUTPUTSET ); // set PCI CLKRUN# to OFF
+ au_writel( 0x00000002, SYS_OUTPUTSET ); // set EXT_IO3 ON
au_writel( 0x00000020, SYS_OUTPUTCLR ); // set eth PHY TX_ER to OFF
// enable LED and set it to green
au_writel( au_readl(GPIO2_DIR) | 0x1800, GPIO2_DIR );
au_writel( 0x18000800, GPIO2_OUTPUT );
+ board_pci_idsel = mtx1_pci_idsel;
+
printk("4G Systems MTX-1 Board\n");
}
+
+int
+mtx1_pci_idsel(unsigned int devsel, int assert)
+{
+#define MTX_IDSEL_ONLY_0_AND_3 0
+#if MTX_IDSEL_ONLY_0_AND_3
+ if (devsel != 0 && devsel != 3) {
+ printk("*** not 0 or 3\n");
+ return 0;
+ }
+#endif
+
+ if (assert && devsel != 0) {
+ // supress signal to cardbus
+ au_writel( 0x00000002, SYS_OUTPUTCLR ); // set EXT_IO3 OFF
+ }
+ else {
+ au_writel( 0x00000002, SYS_OUTPUTSET ); // set EXT_IO3 ON
+ }
+ au_sync_udelay(1);
+ return 1;
+}
+
diff -urN linux-2.6.16.7/arch/mips/au1000/mtx-1/irqmap.c linux-2.6.16.7.new/arch/mips/au1000/mtx-1/irqmap.c
--- linux-2.6.16.7/arch/mips/au1000/mtx-1/irqmap.c 2006-04-23 14:40:54.000000000 +0200
+++ linux-2.6.16.7.new/arch/mips/au1000/mtx-1/irqmap.c 2006-04-23 14:40:12.000000000 +0200
@@ -48,7 +48,7 @@
#include <asm/mach-au1x00/au1000.h>
char irq_tab_alchemy[][5] __initdata = {
- [0] = { -1, INTA, INTB, INTX, INTX}, /* IDSEL 00 - AdapterA-Slot0 (top) */
+ [0] = { -1, INTA, INTA, INTX, INTX}, /* IDSEL 00 - AdapterA-Slot0 (top) */
[1] = { -1, INTB, INTA, INTX, INTX}, /* IDSEL 01 - AdapterA-Slot1 (bottom) */
[2] = { -1, INTC, INTD, INTX, INTX}, /* IDSEL 02 - AdapterB-Slot0 (top) */
[3] = { -1, INTD, INTC, INTX, INTX}, /* IDSEL 03 - AdapterB-Slot1 (bottom) */
|
