From: Rod Whitby Subject: [PATCH] ixp4xx: Add support for the Freecom FSG-3 board (Patch #4874) The Freecom-FSG3 is a small network-attached-storage device with the following feature set: * Intel IXP422 * 4MB Flash (ixp4xx flash driver) * 64MB RAM * 4 USB 2.0 host ports (ehci and ohci drivers) * 1 WAN (eth1) and 3 LAN (eth0) ethernet ports * Supported by the open source ixp4xx ethernet driver * Via VT6421 disk controller (libata and sata-via drivers) * Internal hard disk (PATA supported, SATA not yet supported) * External SATA port (not yet supported) * ISL1208 RTC chip * Winbond 83782 temp sensor and fan controller * MiniPCI slot The ixp4xx_defconfig is also updated to support this device (the leds-fsg driver is to be submitted separately via the leds tree after this initial support is merged, as it depends on header gpio defines). Signed-off-by: Rod Whitby PATCH FOLLOWS KernelVersion: v2.6.25-rc6-74-g264e3e8 --- Updated to correct all issues found by RMK. The front power button calls ctrl_alt_del() and the rear reset button now calls machine_restart() directly. arch/arm/configs/ixp4xx_defconfig | 9 +- arch/arm/mach-ixp4xx/Kconfig | 9 + arch/arm/mach-ixp4xx/Makefile | 2 + arch/arm/mach-ixp4xx/fsg-pci.c | 71 ++++++++ arch/arm/mach-ixp4xx/fsg-setup.c | 276 ++++++++++++++++++++++++++++++++ include/asm-arm/arch-ixp4xx/fsg.h | 50 ++++++ include/asm-arm/arch-ixp4xx/hardware.h | 1 + include/asm-arm/arch-ixp4xx/irqs.h | 7 + 8 files changed, 421 insertions(+), 4 deletions(-) create mode 100644 arch/arm/mach-ixp4xx/fsg-pci.c create mode 100644 arch/arm/mach-ixp4xx/fsg-setup.c create mode 100644 include/asm-arm/arch-ixp4xx/fsg.h Index: linux-2.6.25.1/arch/arm/configs/ixp4xx_defconfig =================================================================== --- linux-2.6.25.1.orig/arch/arm/configs/ixp4xx_defconfig +++ linux-2.6.25.1/arch/arm/configs/ixp4xx_defconfig @@ -165,6 +165,7 @@ CONFIG_ARCH_PRPMC1100=y CONFIG_MACH_NAS100D=y CONFIG_MACH_DSMG600=y CONFIG_ARCH_IXDP4XX=y +CONFIG_MACH_FSG=y CONFIG_CPU_IXP46X=y CONFIG_CPU_IXP43X=y CONFIG_MACH_GTWX5715=y @@ -770,7 +771,7 @@ CONFIG_ATA=y # CONFIG_SATA_SIL24 is not set # CONFIG_SATA_SIS is not set # CONFIG_SATA_ULI is not set -# CONFIG_SATA_VIA is not set +CONFIG_SATA_VIA=y # CONFIG_SATA_VITESSE is not set # CONFIG_SATA_INIC162X is not set # CONFIG_PATA_ALI is not set @@ -1143,7 +1144,7 @@ CONFIG_HWMON=y # CONFIG_SENSORS_VIA686A is not set # CONFIG_SENSORS_VT1211 is not set # CONFIG_SENSORS_VT8231 is not set -# CONFIG_SENSORS_W83781D is not set +CONFIG_SENSORS_W83781D=y # CONFIG_SENSORS_W83791D is not set # CONFIG_SENSORS_W83792D is not set # CONFIG_SENSORS_W83793 is not set @@ -1334,8 +1335,8 @@ CONFIG_LEDS_CLASS=y # # LED drivers # -# CONFIG_LEDS_IXP4XX is not set CONFIG_LEDS_GPIO=y +CONFIG_LEDS_FSG=y # # LED Triggers @@ -1367,7 +1368,7 @@ CONFIG_RTC_INTF_DEV=y # CONFIG_RTC_DRV_DS1672 is not set # CONFIG_RTC_DRV_MAX6900 is not set # CONFIG_RTC_DRV_RS5C372 is not set -# CONFIG_RTC_DRV_ISL1208 is not set +CONFIG_RTC_DRV_ISL1208=y CONFIG_RTC_DRV_X1205=y CONFIG_RTC_DRV_PCF8563=y # CONFIG_RTC_DRV_PCF8583 is not set Index: linux-2.6.25.1/arch/arm/mach-ixp4xx/Kconfig =================================================================== --- linux-2.6.25.1.orig/arch/arm/mach-ixp4xx/Kconfig +++ linux-2.6.25.1/arch/arm/mach-ixp4xx/Kconfig @@ -125,6 +125,15 @@ config ARCH_IXDP4XX depends on ARCH_IXDP425 || MACH_IXDP465 || MACH_KIXRP435 default y +config MACH_FSG + bool + prompt "Freecom FSG-3" + select PCI + help + Say 'Y' here if you want your kernel to support Freecom's + FSG-3 device. For more information on this platform, + see http://www.nslu2-linux.org/wiki/FSG3/HomePage + # # Certain registers and IRQs are only enabled if supporting IXP465 CPUs # Index: linux-2.6.25.1/arch/arm/mach-ixp4xx/Makefile =================================================================== --- linux-2.6.25.1.orig/arch/arm/mach-ixp4xx/Makefile +++ linux-2.6.25.1/arch/arm/mach-ixp4xx/Makefile @@ -15,6 +15,7 @@ obj-pci-$(CONFIG_MACH_NAS100D) += nas10 obj-pci-$(CONFIG_MACH_DSMG600) += dsmg600-pci.o obj-pci-$(CONFIG_MACH_GATEWAY7001) += gateway7001-pci.o obj-pci-$(CONFIG_MACH_WG302V2) += wg302v2-pci.o +obj-pci-$(CONFIG_MACH_FSG) += fsg-pci.o obj-y += common.o @@ -28,6 +29,7 @@ obj-$(CONFIG_MACH_NAS100D) += nas100d-se obj-$(CONFIG_MACH_DSMG600) += dsmg600-setup.o obj-$(CONFIG_MACH_GATEWAY7001) += gateway7001-setup.o obj-$(CONFIG_MACH_WG302V2) += wg302v2-setup.o +obj-$(CONFIG_MACH_FSG) += fsg-setup.o obj-$(CONFIG_PCI) += $(obj-pci-$(CONFIG_PCI)) common-pci.o obj-$(CONFIG_IXP4XX_QMGR) += ixp4xx_qmgr.o Index: linux-2.6.25.1/arch/arm/mach-ixp4xx/fsg-pci.c =================================================================== --- /dev/null +++ linux-2.6.25.1/arch/arm/mach-ixp4xx/fsg-pci.c @@ -0,0 +1,71 @@ +/* + * arch/arch/mach-ixp4xx/fsg-pci.c + * + * FSG board-level PCI initialization + * + * Author: Rod Whitby + * Maintainer: http://www.nslu2-linux.org/ + * + * based on ixdp425-pci.c: + * Copyright (C) 2002 Intel Corporation. + * Copyright (C) 2003-2004 MontaVista Software, Inc. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + */ + +#include +#include +#include + +#include +#include + +void __init fsg_pci_preinit(void) +{ + set_irq_type(IRQ_FSG_PCI_INTA, IRQT_LOW); + set_irq_type(IRQ_FSG_PCI_INTB, IRQT_LOW); + set_irq_type(IRQ_FSG_PCI_INTC, IRQT_LOW); + + ixp4xx_pci_preinit(); +} + +static int __init fsg_map_irq(struct pci_dev *dev, u8 slot, u8 pin) +{ + static int pci_irq_table[FSG_PCI_IRQ_LINES] = { + IRQ_FSG_PCI_INTC, + IRQ_FSG_PCI_INTB, + IRQ_FSG_PCI_INTA, + }; + + int irq = -1; + slot = slot - 11; + + if (slot >= 1 && slot <= FSG_PCI_MAX_DEV && + pin >= 1 && pin <= FSG_PCI_IRQ_LINES) + irq = pci_irq_table[(slot - 1)]; + printk(KERN_INFO "%s: Mapped slot %d pin %d to IRQ %d\n", + __func__, slot, pin, irq); + + return irq; +} + +struct hw_pci fsg_pci __initdata = { + .nr_controllers = 1, + .preinit = fsg_pci_preinit, + .swizzle = pci_std_swizzle, + .setup = ixp4xx_setup, + .scan = ixp4xx_scan_bus, + .map_irq = fsg_map_irq, +}; + +int __init fsg_pci_init(void) +{ + if (machine_is_fsg()) + pci_common_init(&fsg_pci); + return 0; +} + +subsys_initcall(fsg_pci_init); Index: linux-2.6.25.1/arch/arm/mach-ixp4xx/fsg-setup.c =================================================================== --- /dev/null +++ linux-2.6.25.1/arch/arm/mach-ixp4xx/fsg-setup.c @@ -0,0 +1,276 @@ +/* + * arch/arm/mach-ixp4xx/fsg-setup.c + * + * FSG board-setup + * + * Copyright (C) 2008 Rod Whitby + * + * based on ixdp425-setup.c: + * Copyright (C) 2003-2004 MontaVista Software, Inc. + * based on nslu2-power.c + * Copyright (C) 2005 Tower Technologies + * + * Author: Rod Whitby + * Maintainers: http://www.nslu2-linux.org/ + * + */ + +#include +#include +#include +#include +#include +#include +#include +#include + +#include +#include +#include +#include +#include + +static struct flash_platform_data fsg_flash_data = { + .map_name = "cfi_probe", + .width = 2, +}; + +static struct resource fsg_flash_resource = { + .flags = IORESOURCE_MEM, +}; + +static struct platform_device fsg_flash = { + .name = "IXP4XX-Flash", + .id = 0, + .dev = { + .platform_data = &fsg_flash_data, + }, + .num_resources = 1, + .resource = &fsg_flash_resource, +}; + +static struct i2c_gpio_platform_data fsg_i2c_gpio_data = { + .sda_pin = FSG_SDA_PIN, + .scl_pin = FSG_SCL_PIN, +}; + +static struct platform_device fsg_i2c_gpio = { + .name = "i2c-gpio", + .id = 0, + .dev = { + .platform_data = &fsg_i2c_gpio_data, + }, +}; + +static struct i2c_board_info __initdata fsg_i2c_board_info [] = { + { + I2C_BOARD_INFO("rtc-isl1208", 0x6f), + }, +}; + +static struct resource fsg_uart_resources[] = { + { + .start = IXP4XX_UART1_BASE_PHYS, + .end = IXP4XX_UART1_BASE_PHYS + 0x0fff, + .flags = IORESOURCE_MEM, + }, + { + .start = IXP4XX_UART2_BASE_PHYS, + .end = IXP4XX_UART2_BASE_PHYS + 0x0fff, + .flags = IORESOURCE_MEM, + } +}; + +static struct plat_serial8250_port fsg_uart_data[] = { + { + .mapbase = IXP4XX_UART1_BASE_PHYS, + .membase = (char *)IXP4XX_UART1_BASE_VIRT + REG_OFFSET, + .irq = IRQ_IXP4XX_UART1, + .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST, + .iotype = UPIO_MEM, + .regshift = 2, + .uartclk = IXP4XX_UART_XTAL, + }, + { + .mapbase = IXP4XX_UART2_BASE_PHYS, + .membase = (char *)IXP4XX_UART2_BASE_VIRT + REG_OFFSET, + .irq = IRQ_IXP4XX_UART2, + .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST, + .iotype = UPIO_MEM, + .regshift = 2, + .uartclk = IXP4XX_UART_XTAL, + }, + { } +}; + +static struct platform_device fsg_uart = { + .name = "serial8250", + .id = PLAT8250_DEV_PLATFORM, + .dev = { + .platform_data = fsg_uart_data, + }, + .num_resources = ARRAY_SIZE(fsg_uart_resources), + .resource = fsg_uart_resources, +}; + +static struct platform_device fsg_leds = { + .name = "fsg-led", + .id = -1, +}; + +/* Built-in 10/100 Ethernet MAC interfaces */ +static struct eth_plat_info fsg_plat_eth[] = { + { + .phy = 5, + .rxq = 3, + .txreadyq = 20, + }, { + .phy = 4, + .rxq = 4, + .txreadyq = 21, + } +}; + +static struct platform_device fsg_eth[] = { + { + .name = "ixp4xx_eth", + .id = IXP4XX_ETH_NPEB, + .dev = { + .platform_data = fsg_plat_eth, + }, + }, { + .name = "ixp4xx_eth", + .id = IXP4XX_ETH_NPEC, + .dev = { + .platform_data = fsg_plat_eth + 1, + }, + } +}; + +static struct platform_device *fsg_devices[] __initdata = { + &fsg_i2c_gpio, + &fsg_flash, + &fsg_leds, + &fsg_eth[0], + &fsg_eth[1], +}; + +static irqreturn_t fsg_power_handler(int irq, void *dev_id) +{ + /* Signal init to do the ctrlaltdel action, this will bypass init if + * it hasn't started and do a kernel_restart. + */ + ctrl_alt_del(); + + return IRQ_HANDLED; +} + +static irqreturn_t fsg_reset_handler(int irq, void *dev_id) +{ + /* This is the paper-clip reset which does an emergency reboot. */ + printk(KERN_INFO "Restarting system.\n"); + machine_restart(NULL); + + /* This should never be reached. */ + return IRQ_HANDLED; +} + +static void __init fsg_init(void) +{ + DECLARE_MAC_BUF(mac_buf); + uint8_t __iomem *f; + int i; + + ixp4xx_sys_init(); + + fsg_flash_resource.start = IXP4XX_EXP_BUS_BASE(0); + fsg_flash_resource.end = + IXP4XX_EXP_BUS_BASE(0) + ixp4xx_exp_bus_size - 1; + + *IXP4XX_EXP_CS0 |= IXP4XX_FLASH_WRITABLE; + *IXP4XX_EXP_CS1 = *IXP4XX_EXP_CS0; + + /* Configure CS2 for operation, 8bit and writable */ + *IXP4XX_EXP_CS2 = 0xbfff0002; + + i2c_register_board_info(0, fsg_i2c_board_info, + ARRAY_SIZE(fsg_i2c_board_info)); + + /* This is only useful on a modified machine, but it is valuable + * to have it first in order to see debug messages, and so that + * it does *not* get removed if platform_add_devices fails! + */ + (void)platform_device_register(&fsg_uart); + + platform_add_devices(fsg_devices, ARRAY_SIZE(fsg_devices)); + + if (request_irq(gpio_to_irq(FSG_RB_GPIO), &fsg_reset_handler, + IRQF_DISABLED | IRQF_TRIGGER_LOW, + "FSG reset button", NULL) < 0) { + + printk(KERN_DEBUG "Reset Button IRQ %d not available\n", + gpio_to_irq(FSG_RB_GPIO)); + } + + if (request_irq(gpio_to_irq(FSG_SB_GPIO), &fsg_power_handler, + IRQF_DISABLED | IRQF_TRIGGER_LOW, + "FSG power button", NULL) < 0) { + + printk(KERN_DEBUG "Power Button IRQ %d not available\n", + gpio_to_irq(FSG_SB_GPIO)); + } + + /* + * Map in a portion of the flash and read the MAC addresses. + * Since it is stored in BE in the flash itself, we need to + * byteswap it if we're in LE mode. + */ + f = ioremap(IXP4XX_EXP_BUS_BASE(0), 0x400000); + if (f) { +#ifdef __ARMEB__ + for (i = 0; i < 6; i++) { + fsg_plat_eth[0].hwaddr[i] = readb(f + 0x3C0422 + i); + fsg_plat_eth[1].hwaddr[i] = readb(f + 0x3C043B + i); + } +#else + + /* + Endian-swapped reads from unaligned addresses are + required to extract the two MACs from the big-endian + Redboot config area in flash. + */ + + fsg_plat_eth[0].hwaddr[0] = readb(f + 0x3C0421); + fsg_plat_eth[0].hwaddr[1] = readb(f + 0x3C0420); + fsg_plat_eth[0].hwaddr[2] = readb(f + 0x3C0427); + fsg_plat_eth[0].hwaddr[3] = readb(f + 0x3C0426); + fsg_plat_eth[0].hwaddr[4] = readb(f + 0x3C0425); + fsg_plat_eth[0].hwaddr[5] = readb(f + 0x3C0424); + + fsg_plat_eth[1].hwaddr[0] = readb(f + 0x3C0439); + fsg_plat_eth[1].hwaddr[1] = readb(f + 0x3C043F); + fsg_plat_eth[1].hwaddr[2] = readb(f + 0x3C043E); + fsg_plat_eth[1].hwaddr[3] = readb(f + 0x3C043D); + fsg_plat_eth[1].hwaddr[4] = readb(f + 0x3C043C); + fsg_plat_eth[1].hwaddr[5] = readb(f + 0x3C0443); +#endif + iounmap(f); + } + printk(KERN_INFO "FSG: Using MAC address %s for port 0\n", + print_mac(mac_buf, fsg_plat_eth[0].hwaddr)); + printk(KERN_INFO "FSG: Using MAC address %s for port 1\n", + print_mac(mac_buf, fsg_plat_eth[1].hwaddr)); + +} + +MACHINE_START(FSG, "Freecom FSG-3") + /* Maintainer: www.nslu2-linux.org */ + .phys_io = IXP4XX_PERIPHERAL_BASE_PHYS, + .io_pg_offst = ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xfffc, + .map_io = ixp4xx_map_io, + .init_irq = ixp4xx_init_irq, + .timer = &ixp4xx_timer, + .boot_params = 0x0100, + .init_machine = fsg_init, +MACHINE_END + Index: linux-2.6.25.1/include/asm-arm/arch-ixp4xx/fsg.h =================================================================== --- /dev/null +++ linux-2.6.25.1/include/asm-arm/arch-ixp4xx/fsg.h @@ -0,0 +1,50 @@ +/* + * include/asm-arm/arch-ixp4xx/fsg.h + * + * Freecom FSG-3 platform specific definitions + * + * Author: Rod Whitby + * Author: Tomasz Chmielewski + * Maintainers: http://www.nslu2-linux.org + * + * Based on coyote.h by + * Copyright 2004 (c) MontaVista, Software, Inc. + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#ifndef __ASM_ARCH_HARDWARE_H__ +#error "Do not include this directly, instead #include " +#endif + +#define FSG_SDA_PIN 12 +#define FSG_SCL_PIN 13 + +/* + * FSG PCI IRQs + */ +#define FSG_PCI_MAX_DEV 3 +#define FSG_PCI_IRQ_LINES 3 + + +/* PCI controller GPIO to IRQ pin mappings */ +#define FSG_PCI_INTA_PIN 6 +#define FSG_PCI_INTB_PIN 7 +#define FSG_PCI_INTC_PIN 5 + +/* Buttons */ + +#define FSG_SB_GPIO 4 /* sync button */ +#define FSG_RB_GPIO 9 /* reset button */ +#define FSG_UB_GPIO 10 /* usb button */ + +/* LEDs */ + +#define FSG_LED_WLAN_BIT 0 +#define FSG_LED_WAN_BIT 1 +#define FSG_LED_SATA_BIT 2 +#define FSG_LED_USB_BIT 4 +#define FSG_LED_RING_BIT 5 +#define FSG_LED_SYNC_BIT 7 Index: linux-2.6.25.1/include/asm-arm/arch-ixp4xx/hardware.h =================================================================== --- linux-2.6.25.1.orig/include/asm-arm/arch-ixp4xx/hardware.h +++ linux-2.6.25.1/include/asm-arm/arch-ixp4xx/hardware.h @@ -45,5 +45,6 @@ #include "nslu2.h" #include "nas100d.h" #include "dsmg600.h" +#include "fsg.h" #endif /* _ASM_ARCH_HARDWARE_H */ Index: linux-2.6.25.1/include/asm-arm/arch-ixp4xx/irqs.h =================================================================== --- linux-2.6.25.1.orig/include/asm-arm/arch-ixp4xx/irqs.h +++ linux-2.6.25.1/include/asm-arm/arch-ixp4xx/irqs.h @@ -128,4 +128,11 @@ #define IRQ_DSMG600_PCI_INTE IRQ_IXP4XX_GPIO7 #define IRQ_DSMG600_PCI_INTF IRQ_IXP4XX_GPIO6 +/* + * Freecom FSG-3 Board IRQs + */ +#define IRQ_FSG_PCI_INTA IRQ_IXP4XX_GPIO6 +#define IRQ_FSG_PCI_INTB IRQ_IXP4XX_GPIO7 +#define IRQ_FSG_PCI_INTC IRQ_IXP4XX_GPIO5 + #endif