--- a/drivers/bcma/driver_chipcommon_pmu.c
+++ b/drivers/bcma/driver_chipcommon_pmu.c
@@ -263,7 +263,7 @@ static u32 bcma_pmu_pll_clock_bcm4706(st
 }
 
 /* query bus clock frequency for PMU-enabled chipcommon */
-static u32 bcma_pmu_get_bus_clock(struct bcma_drv_cc *cc)
+u32 bcma_pmu_get_bus_clock(struct bcma_drv_cc *cc)
 {
 	struct bcma_bus *bus = cc->core->bus;
 
@@ -292,6 +292,7 @@ static u32 bcma_pmu_get_bus_clock(struct
 	}
 	return BCMA_CC_PMU_HT_CLOCK;
 }
+EXPORT_SYMBOL_GPL(bcma_pmu_get_bus_clock);
 
 /* query cpu clock frequency for PMU-enabled chipcommon */
 u32 bcma_pmu_get_cpu_clock(struct bcma_drv_cc *cc)
--- a/drivers/net/ethernet/broadcom/Kconfig
+++ b/drivers/net/ethernet/broadcom/Kconfig
@@ -120,4 +120,10 @@ config BNX2X
 	  To compile this driver as a module, choose M here: the module
 	  will be called bnx2x.  This is recommended.
 
+config BGMAC
+	tristate "Broadcom Gigabit driver"
+	depends on BCMA
+	---help---
+	  This driver supports Broadcom Gigabit core found in some BCM47xx SoCs.
+
 endif # NET_VENDOR_BROADCOM
--- a/drivers/net/ethernet/broadcom/Makefile
+++ b/drivers/net/ethernet/broadcom/Makefile
@@ -9,3 +9,4 @@ obj-$(CONFIG_CNIC) += cnic.o
 obj-$(CONFIG_BNX2X) += bnx2x/
 obj-$(CONFIG_SB1250_MAC) += sb1250-mac.o
 obj-$(CONFIG_TIGON3) += tg3.o
+obj-$(CONFIG_BGMAC) += bgmac.o
--- /dev/null
+++ b/drivers/net/ethernet/broadcom/bgmac.c
@@ -0,0 +1,1202 @@
+#define pr_fmt(fmt)		KBUILD_MODNAME ": " fmt
+
+#define bgmac_err(bgmac, fmt, ...) \
+	pr_err("u%d: " fmt, (bgmac)->core->core_unit, ##__VA_ARGS__)
+#define bgmac_warn(bgmac, fmt, ...) \
+	pr_warn("u%d: " fmt, (bgmac)->core->core_unit, ##__VA_ARGS__)
+#define bgmac_info(bgmac, fmt, ...) \
+	pr_info("u%d: " fmt, (bgmac)->core->core_unit, ##__VA_ARGS__)
+#define bgmac_debug(bgmac, fmt, ...) \
+	pr_debug("u%d: " fmt, (bgmac)->core->core_unit, ##__VA_ARGS__)
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/delay.h>
+#include <linux/etherdevice.h>
+#include <linux/mii.h>
+#include <linux/interrupt.h>
+#include <linux/dma-mapping.h>
+#include <bcm47xx_nvram.h>
+
+#include "bgmac.h"
+
+#define ETHER_MAX_LEN   1518
+
+MODULE_LICENSE("GPL");
+
+static const struct bcma_device_id bgmac_bcma_tbl[] = {
+	BCMA_CORE(BCMA_MANUF_BCM, BCMA_CORE_4706_MAC_GBIT, BCMA_ANY_REV, BCMA_ANY_CLASS),
+	BCMA_CORE(BCMA_MANUF_BCM, BCMA_CORE_MAC_GBIT, BCMA_ANY_REV, BCMA_ANY_CLASS),
+	BCMA_CORETABLE_END
+};
+MODULE_DEVICE_TABLE(bcma, bgmac_bcma_tbl);
+
+static bool bgmac_wait_value(struct bcma_device *core, u16 reg, u32 mask,
+			     u32 value, int timeout)
+{
+	u32 val;
+	int i;
+
+	for (i = 0; i < timeout / 10; i++) {
+		val = bcma_read32(core, reg);
+		if ((val & mask) == value)
+			return true;
+		udelay(10);
+	}
+	pr_err("Timeout waiting for reg 0x%X\n", reg);
+	return false;
+}
+
+/**************************************************
+ * DMA
+ **************************************************/
+
+static void bgmac_dma_tx_reset(struct bgmac *bgmac, struct bgmac_dma_ring *ring)
+{
+	u32 val;
+	int i;
+
+	if (!ring->mmio_base)
+		return;
+
+	/* Susend DMA TX ring first.
+	 * bgmac_wait_value doesn't support waiting for any of few values, so
+	 * implement whole loop here.
+	 */
+	bgmac_write(bgmac, ring->mmio_base + BGMAC_DMA_TX_CTL,
+		    BGMAC_DMA_TX_SUSPEND);
+	for (i = 0; i < 10000 / 10; i++) {
+		val = bgmac_read(bgmac, ring->mmio_base + BGMAC_DMA_TX_STATUS);
+		if (val == BGMAC_DMA_TX_STAT_DISABLED ||
+		    val == BGMAC_DMA_TX_STAT_IDLEWAIT ||
+		    val == BGMAC_DMA_TX_STAT_STOPPED) {
+			i = 0;
+			break;
+		}
+		udelay(10);
+	}
+	if (i)
+		bgmac_err(bgmac, "Timeout suspending DMA TX ring 0x%X\n", ring->mmio_base);
+
+	/* Remove SUSPEND bit */
+	bgmac_write(bgmac, ring->mmio_base + BGMAC_DMA_TX_CTL, 0);
+	if (!bgmac_wait_value(bgmac->core,
+			      ring->mmio_base + BGMAC_DMA_TX_STATUS,
+			      BGMAC_DMA_TX_STAT, BGMAC_DMA_TX_STAT_DISABLED,
+			      10000)) {
+		bgmac_warn(bgmac, "DMA TX ring 0x%X wasn't disabled on time, waiting additional 300us\n", ring->mmio_base);
+		udelay(300);
+		val = bgmac_read(bgmac, ring->mmio_base + BGMAC_DMA_TX_STATUS);
+		if ((val & BGMAC_DMA_TX_STAT) != BGMAC_DMA_TX_STAT_DISABLED)
+			bgmac_err(bgmac, "Reset of DMA TX ring 0x%X failed\n", ring->mmio_base);
+	}
+}
+
+static void bgmac_dma_tx_enable(struct bgmac *bgmac,
+				struct bgmac_dma_ring *ring)
+{
+	u32 ctl;
+
+	ctl = bgmac_read(bgmac, ring->mmio_base + BGMAC_DMA_TX_CTL);
+	ctl |= BGMAC_DMA_TX_ENABLE;
+	ctl |= BGMAC_DMA_TX_PARITY_DISABLE;
+	bgmac_write(bgmac, ring->mmio_base + BGMAC_DMA_TX_CTL, ctl);
+}
+
+static netdev_tx_t bgmac_dma_tx_add(struct bgmac *bgmac,
+				    struct bgmac_dma_ring *ring,
+				    struct sk_buff *skb)
+{
+	struct device *dma_dev = bgmac->core->dma_dev;
+	struct bgmac_dma_desc *dma_desc;
+	struct bgmac_slot_info *slot;
+	u32 ctl0, ctl1;
+	int free_slots;
+
+	if (skb->len > BGMAC_DESC_CTL1_LEN) {
+		bgmac_err(bgmac, "Too long skb (%d)\n", skb->len);
+		return NETDEV_TX_BUSY;
+	}
+
+	if (ring->start <= ring->end)
+		free_slots = ring->start - ring->end + BGMAC_TX_RING_SLOTS;
+	else
+		free_slots = ring->start - ring->end;
+	if (free_slots <= 1) {
+		bgmac_err(bgmac, "No free slots on ring 0x%X!\n", ring->mmio_base);
+		netif_stop_queue(bgmac->net_dev);
+		return NETDEV_TX_BUSY;
+	}
+
+	slot = &ring->slots[ring->end];
+	slot->skb = skb;
+	slot->dma_addr = dma_map_single(dma_dev, skb->data, skb->len, DMA_TO_DEVICE);
+	if (dma_mapping_error(dma_dev, slot->dma_addr)) {
+		bgmac_err(bgmac, "Mapping error of skb on ring 0x%X\n", ring->mmio_base);
+		return NETDEV_TX_BUSY;
+	}
+
+	ctl0 = BGMAC_DESC_CTL0_IOC | BGMAC_DESC_CTL0_SOF | BGMAC_DESC_CTL0_EOF;
+	if (ring->end == ring->num_slots - 1)
+		ctl0 |= BGMAC_DESC_CTL0_EOT;
+	ctl1 = skb->len & BGMAC_DESC_CTL1_LEN;
+
+	dma_desc = ring->cpu_base;
+	dma_desc += ring->end;
+	dma_desc->addr_low = cpu_to_le32(lower_32_bits(slot->dma_addr));
+	dma_desc->addr_high = cpu_to_le32(upper_32_bits(slot->dma_addr));
+	dma_desc->ctl0 = cpu_to_le32(ctl0);
+	dma_desc->ctl1 = cpu_to_le32(ctl1);
+
+	wmb();
+
+	/* Increase ring->end to point empty slot. We tell hardware the first
+	 * slot it shold *not* read.
+	 */
+	if (++ring->end >= BGMAC_TX_RING_SLOTS)
+		ring->end = 0;
+	bgmac_write(bgmac, ring->mmio_base + BGMAC_DMA_TX_INDEX,
+		    ring->end * sizeof(struct bgmac_dma_desc));
+
+	return NETDEV_TX_OK;
+}
+
+/* Free transmitted packets */
+static void bgmac_dma_tx_free(struct bgmac *bgmac, struct bgmac_dma_ring *ring)
+{
+	struct device *dma_dev = bgmac->core->dma_dev;
+	struct bgmac_dma_desc *dma_desc;
+	struct bgmac_slot_info *slot;
+	int empty_slot;
+
+	/* The last slot that hardware didn't consume yet */
+	empty_slot = bgmac_read(bgmac, ring->mmio_base + BGMAC_DMA_TX_STATUS);
+	empty_slot &= BGMAC_DMA_TX_STATDPTR;
+	empty_slot /= sizeof(struct bgmac_dma_desc);
+
+	while (ring->start != empty_slot) {
+		/* Set pointers */
+		dma_desc = ring->cpu_base;
+		dma_desc += ring->start;
+		slot = &ring->slots[ring->start];
+
+		if (slot->skb) {
+			/* Unmap no longer used buffer */
+			dma_unmap_single(dma_dev, slot->dma_addr,
+					 slot->skb->len, DMA_TO_DEVICE);
+			slot->dma_addr = 0;
+
+			/* Free memory!  */
+			dev_kfree_skb_any(slot->skb);
+			slot->skb = NULL;
+		} else {
+			bgmac_err(bgmac, "Hardware reported transmission for empty TX ring slot %d! End of ring: %d", ring->start, ring->end);
+		}
+
+		if (++ring->start >= BGMAC_TX_RING_SLOTS)
+			ring->start = 0;
+	}
+}
+
+static void bgmac_dma_rx_reset(struct bgmac *bgmac, struct bgmac_dma_ring *ring)
+{
+	if (!ring->mmio_base)
+		return;
+
+	bgmac_write(bgmac, ring->mmio_base + BGMAC_DMA_RX_CTL, 0);
+	if (!bgmac_wait_value(bgmac->core,
+			      ring->mmio_base + BGMAC_DMA_RX_STATUS,
+			      BGMAC_DMA_RX_STAT, BGMAC_DMA_RX_STAT_DISABLED,
+			      10000))
+		bgmac_err(bgmac, "Reset of ring 0x%X RX failed\n", ring->mmio_base);
+}
+
+static void bgmac_dma_rx_enable(struct bgmac *bgmac,
+				struct bgmac_dma_ring *ring)
+{
+	u32 ctl;
+
+	ctl = bgmac_read(bgmac, ring->mmio_base + BGMAC_DMA_RX_CTL);
+	ctl &= BGMAC_DMA_RX_ADDREXT_MASK;
+	ctl |= BGMAC_DMA_RX_ENABLE;
+	ctl |= BGMAC_DMA_RX_PARITY_DISABLE;
+	ctl |= BGMAC_DMA_RX_OVERFLOW_CONT;
+	ctl |= BGMAC_RX_FRAME_OFFSET << BGMAC_DMA_RX_FRAME_OFFSET_SHIFT;
+	bgmac_write(bgmac, ring->mmio_base + BGMAC_DMA_RX_CTL, ctl);
+}
+
+static void bgmac_dma_rx_skb_for_slot(struct bgmac *bgmac,
+				      struct bgmac_slot_info *slot)
+{
+	struct device *dma_dev = bgmac->core->dma_dev;
+	struct bgmac_rx_header *rx;
+
+	/* Alloc skb */
+	slot->skb = netdev_alloc_skb(bgmac->net_dev, BGMAC_RX_BUF_SIZE);
+	if (!slot->skb)
+		bgmac_err(bgmac, "Allocation of skb failed!\n");
+
+	/* Poison - if everything goes fine, hardware will overwrite it */
+	rx = (struct bgmac_rx_header *)slot->skb->data;
+	rx->len = cpu_to_le16(0xdead);
+	rx->flags = cpu_to_le16(0xbeef);
+
+	/* Map skb for the DMA */
+	slot->dma_addr = dma_map_single(dma_dev, slot->skb->data,
+					BGMAC_RX_BUF_SIZE, DMA_FROM_DEVICE);
+	if (dma_mapping_error(dma_dev, slot->dma_addr))
+		bgmac_err(bgmac, "DMA mapping error\n");
+	if (slot->dma_addr & 0xC0000000)
+		bgmac_warn(bgmac, "DMA address using 0xC0000000 bit(s), it may need translation trick\n");
+}
+
+static void bgmac_dma_rx_read(struct bgmac *bgmac, struct bgmac_dma_ring *ring)
+{
+	struct device *dma_dev = bgmac->core->dma_dev;
+	struct bgmac_dma_desc *dma_desc;
+	struct bgmac_slot_info *slot;
+	struct sk_buff *skb;
+	struct bgmac_rx_header *rx;
+	u32 end_slot;
+	u16 len, flags;
+
+	end_slot = bgmac_read(bgmac, ring->mmio_base + BGMAC_DMA_RX_STATUS);
+	end_slot &= BGMAC_DMA_RX_STATDPTR;
+	end_slot /= sizeof(struct bgmac_dma_desc);
+
+	ring->end = end_slot;
+
+	while (ring->start != ring->end) {
+		/* Set pointers */
+		dma_desc = ring->cpu_base;
+		dma_desc += ring->start;
+		slot = &ring->slots[ring->start];
+		skb = slot->skb;
+
+		/* Unmap buffer to make it accessible to the CPU */
+		dma_unmap_single(dma_dev, slot->dma_addr, BGMAC_RX_BUF_SIZE,
+				 DMA_FROM_DEVICE);
+
+		/* Get info from the header */
+		rx = (struct bgmac_rx_header *)skb->data;
+		len = le16_to_cpu(rx->len);
+		flags = le16_to_cpu(rx->flags);
+
+		/* Check for poison and drop or pass packet */
+		if (len == 0xdead && flags == 0xbeef) {
+			bgmac_err(bgmac, "Found poisoned packet at slot %d, DMA issue!\n", ring->start);
+			dev_kfree_skb_any(skb);
+		} else {
+			/* Remove header from the skb and pass it to the net */
+			skb_put(skb, BGMAC_RX_FRAME_OFFSET + len);
+			skb_pull(skb, BGMAC_RX_FRAME_OFFSET);
+			skb->protocol = eth_type_trans(skb, bgmac->net_dev);
+			netif_receive_skb(skb);
+		}
+
+		/* Alloc new skb */
+		bgmac_dma_rx_skb_for_slot(bgmac, slot);
+		dma_desc->addr_low = cpu_to_le32(lower_32_bits(slot->dma_addr));
+		dma_desc->addr_high = cpu_to_le32(upper_32_bits(slot->dma_addr));
+
+		if (++ring->start >= BGMAC_RX_RING_SLOTS)
+			ring->start = 0;
+	}
+}
+
+/* Does ring support unaligned addressing? */
+static bool bgmac_dma_unaligned(struct bgmac *bgmac,
+				struct bgmac_dma_ring *ring)
+{
+	if (ring->tx) {
+		bgmac_write(bgmac, ring->mmio_base + BGMAC_DMA_TX_RINGLO,
+			    0xff0);
+		if (bgmac_read(bgmac, ring->mmio_base + BGMAC_DMA_TX_RINGLO))
+			return true;
+	} else {
+		bgmac_write(bgmac, ring->mmio_base + BGMAC_DMA_RX_RINGLO,
+			    0xff0);
+		if (bgmac_read(bgmac, ring->mmio_base + BGMAC_DMA_RX_RINGLO))
+			return true;
+	}
+	return false;
+}
+
+static int bgmac_dma_alloc(struct bgmac *bgmac)
+{
+	struct device *dma_dev = bgmac->core->dma_dev;
+	struct bgmac_dma_ring *ring;
+	u16 ring_base[] = { BGMAC_DMA_BASE0, BGMAC_DMA_BASE1, BGMAC_DMA_BASE2,
+			    BGMAC_DMA_BASE3, };
+	int size; /* ring size: different for Tx and Rx */
+	int i;
+
+	BUILD_BUG_ON(BGMAC_MAX_TX_RINGS > ARRAY_SIZE(ring_base));
+	BUILD_BUG_ON(BGMAC_MAX_RX_RINGS > ARRAY_SIZE(ring_base));
+
+	if (!(bcma_aread32(bgmac->core, BCMA_IOST) & BCMA_IOST_DMA64)) {
+		bgmac_err(bgmac, "Core does not report 64-bit DMA\n");
+		return -ENOTSUPP;
+	}
+
+	for (i = 0; i < BGMAC_MAX_TX_RINGS; i++) {
+		ring = &bgmac->tx_ring[i];
+		ring->tx = true;
+		ring->num_slots = BGMAC_TX_RING_SLOTS;
+		ring->mmio_base = ring_base[i];
+		if (bgmac_dma_unaligned(bgmac, ring))
+			bgmac_warn(bgmac, "TX on ring 0x%X supports unaligned addressing but this feature is not implemented\n", ring->mmio_base);
+
+		/* Alloc ring of descriptors */
+		size = ring->num_slots * sizeof(struct bgmac_dma_desc);
+		ring->cpu_base = dma_zalloc_coherent(dma_dev, size,
+						     &(ring->dma_base),
+						     GFP_KERNEL);
+		if (!ring->cpu_base)
+			bgmac_err(bgmac, "Allocation of TX ring failed\n");
+		if (ring->dma_base & 0xC0000000)
+			bgmac_warn(bgmac, "DMA address using 0xC0000000 bit(s), it may need translation trick\n");
+
+		/* No need to alloc TX slots yet */
+	}
+
+	for (i = 0; i < BGMAC_MAX_RX_RINGS; i++) {
+		ring = &bgmac->rx_ring[i];
+		ring->tx = false;
+		ring->num_slots = BGMAC_RX_RING_SLOTS;
+		ring->mmio_base = ring_base[i];
+		if (bgmac_dma_unaligned(bgmac, ring))
+			bgmac_warn(bgmac, "RX on ring 0x%X supports unaligned addressing but this feature is not implemented\n", ring->mmio_base);
+
+		/* Alloc ring of descriptors */
+		size = ring->num_slots * sizeof(struct bgmac_dma_desc);
+		ring->cpu_base = dma_zalloc_coherent(dma_dev, size,
+						     &(ring->dma_base),
+						     GFP_KERNEL);
+		if (!ring->cpu_base)
+			bgmac_err(bgmac, "Allocation of RX ring failed\n");
+		if (ring->dma_base & 0xC0000000)
+			bgmac_warn(bgmac, "DMA address using 0xC0000000 bit(s), it may need translation trick\n");
+
+		/* Alloc RX slots */
+		for (i = 0; i < ring->num_slots; i++)
+			bgmac_dma_rx_skb_for_slot(bgmac, &ring->slots[i]);
+	}
+
+	return 0;
+}
+
+static void bgmac_dma_init(struct bgmac *bgmac)
+{
+	struct bgmac_dma_ring *ring;
+	struct bgmac_dma_desc *dma_desc;
+	u32 ctl0, ctl1;
+	int i;
+
+	for (i = 0; i < BGMAC_MAX_TX_RINGS; i++) {
+		ring = &bgmac->tx_ring[i];
+
+		/* We don't implement unaligned addressing, so enable first */
+		bgmac_dma_tx_enable(bgmac, ring);
+		bgmac_write(bgmac, ring->mmio_base + BGMAC_DMA_TX_RINGLO,
+			    lower_32_bits(ring->dma_base));
+		bgmac_write(bgmac, ring->mmio_base + BGMAC_DMA_TX_RINGHI,
+			    upper_32_bits(ring->dma_base));
+
+		ring->start = 0;
+		ring->end = 0;	/* Points the slot that should *not* be read */
+	}
+
+	for (i = 0; i < BGMAC_MAX_RX_RINGS; i++) {
+		ring = &bgmac->rx_ring[i];
+
+		/* We don't implement unaligned addressing, so enable first */
+		bgmac_dma_rx_enable(bgmac, ring);
+		bgmac_write(bgmac, ring->mmio_base + BGMAC_DMA_RX_RINGLO,
+			    lower_32_bits(ring->dma_base));
+		bgmac_write(bgmac, ring->mmio_base + BGMAC_DMA_RX_RINGHI,
+			    upper_32_bits(ring->dma_base));
+
+		for (i = 0, dma_desc = ring->cpu_base; i < ring->num_slots;
+		     i++, dma_desc++) {
+			ctl0 = ctl1 = 0;
+
+			if (i == ring->num_slots - 1)
+				ctl0 |= BGMAC_DESC_CTL0_EOT;
+			ctl1 |= BGMAC_RX_BUF_SIZE & BGMAC_DESC_CTL1_LEN;
+			/* Is there any BGMAC device that requires extension? */
+			/* ctl1 |= (addrext << B43_DMA64_DCTL1_ADDREXT_SHIFT) &
+			 * B43_DMA64_DCTL1_ADDREXT_MASK;
+			 */
+
+			dma_desc->addr_low = cpu_to_le32(lower_32_bits(ring->slots[i].dma_addr));
+			dma_desc->addr_high = cpu_to_le32(upper_32_bits(ring->slots[i].dma_addr));
+			dma_desc->ctl0 = cpu_to_le32(ctl0);
+			dma_desc->ctl1 = cpu_to_le32(ctl1);
+		}
+
+		bgmac_write(bgmac, ring->mmio_base + BGMAC_DMA_RX_INDEX,
+			    ring->num_slots * sizeof(struct bgmac_dma_desc));
+
+		ring->start = 0;
+		ring->end = 0;
+	}
+}
+
+/**************************************************
+ * PHY ops
+ **************************************************/
+
+u16 bgmac_phy_read(struct bgmac *bgmac, u8 phyaddr, u8 reg)
+{
+	struct bcma_device *core;
+	u16 phy_access_addr;
+	u16 phy_ctl_addr;
+	u32 tmp;
+
+	BUILD_BUG_ON(BGMAC_PA_DATA_MASK != BCMA_GMAC_CMN_PA_DATA_MASK);
+	BUILD_BUG_ON(BGMAC_PA_ADDR_MASK != BCMA_GMAC_CMN_PA_ADDR_MASK);
+	BUILD_BUG_ON(BGMAC_PA_ADDR_SHIFT != BCMA_GMAC_CMN_PA_ADDR_SHIFT);
+	BUILD_BUG_ON(BGMAC_PA_REG_MASK != BCMA_GMAC_CMN_PA_REG_MASK);
+	BUILD_BUG_ON(BGMAC_PA_REG_SHIFT != BCMA_GMAC_CMN_PA_REG_SHIFT);
+	BUILD_BUG_ON(BGMAC_PA_WRITE != BCMA_GMAC_CMN_PA_WRITE);
+	BUILD_BUG_ON(BGMAC_PA_START != BCMA_GMAC_CMN_PA_START);
+	BUILD_BUG_ON(BGMAC_PC_EPA_MASK != BCMA_GMAC_CMN_PC_EPA_MASK);
+	BUILD_BUG_ON(BGMAC_PC_MCT_MASK != BCMA_GMAC_CMN_PC_MCT_MASK);
+	BUILD_BUG_ON(BGMAC_PC_MCT_SHIFT != BCMA_GMAC_CMN_PC_MCT_SHIFT);
+	BUILD_BUG_ON(BGMAC_PC_MTE != BCMA_GMAC_CMN_PC_MTE);
+
+	if (bgmac->core->id.id == BCMA_CORE_4706_MAC_GBIT) {
+		core = bgmac->core->bus->drv_gmac_cmn.core;
+		phy_access_addr = BCMA_GMAC_CMN_PHY_ACCESS;
+		phy_ctl_addr = BCMA_GMAC_CMN_PHY_CTL;
+	} else {
+		core = bgmac->core;
+		phy_access_addr = BGMAC_PHY_ACCESS;
+		phy_ctl_addr = BGMAC_PHY_CNTL;
+	}
+
+	tmp = bcma_read32(core, phy_ctl_addr);
+	tmp &= ~BGMAC_PC_EPA_MASK;
+	tmp |= phyaddr;
+	bcma_write32(core, phy_ctl_addr, tmp);
+
+	tmp = BGMAC_PA_START;
+	tmp |= phyaddr << BGMAC_PA_ADDR_SHIFT;
+	tmp |= reg << BGMAC_PA_REG_SHIFT;
+	bcma_write32(core, phy_access_addr, tmp);
+
+	if (!bgmac_wait_value(core, phy_access_addr, BGMAC_PA_START, 0, 1000)) {
+		bgmac_err(bgmac, "Reading PHY %d register 0x%X failed\n",
+			  phyaddr, reg);
+		return 0xffff;
+	}
+
+	return bcma_read32(core, phy_access_addr) & BGMAC_PA_DATA_MASK;
+}
+
+/* http://bcm-v4.sipsolutions.net/mac-gbit/gmac/chipphywr */
+void bgmac_phy_write(struct bgmac *bgmac, u8 phyaddr, u8 reg, u16 value)
+{
+	struct bcma_device *core;
+	u16 phy_access_addr;
+	u16 phy_ctl_addr;
+	u32 tmp;
+
+	if (bgmac->core->id.id == BCMA_CORE_4706_MAC_GBIT) {
+		core = bgmac->core->bus->drv_gmac_cmn.core;
+		phy_access_addr = BCMA_GMAC_CMN_PHY_ACCESS;
+		phy_ctl_addr = BCMA_GMAC_CMN_PHY_CTL;
+	} else {
+		core = bgmac->core;
+		phy_access_addr = BGMAC_PHY_ACCESS;
+		phy_ctl_addr = BGMAC_PHY_CNTL;
+	}
+
+	tmp = bcma_read32(core, phy_ctl_addr);
+	tmp &= ~BGMAC_PC_EPA_MASK;
+	tmp |= phyaddr;
+	bcma_write32(core, phy_ctl_addr, tmp);
+
+	bgmac_write(bgmac, BGMAC_INT_STATUS, BGMAC_IS_MDIO);
+	if (bgmac_read(bgmac, BGMAC_INT_STATUS) & BGMAC_IS_MDIO)
+		bgmac_warn(bgmac, "Error setting MDIO int\n");
+
+	tmp = BGMAC_PA_START;
+	tmp |= BGMAC_PA_WRITE;
+	tmp |= phyaddr << BGMAC_PA_ADDR_SHIFT;
+	tmp |= reg << BGMAC_PA_REG_SHIFT;
+	tmp |= value;
+	bcma_write32(core, phy_access_addr, tmp);
+
+	if (!bgmac_wait_value(core, phy_access_addr, BGMAC_PA_START, 0, 1000))
+		bgmac_err(bgmac, "Writing to PHY %d register 0x%X failed\n",
+			  phyaddr, reg);
+}
+
+/* http://bcm-v4.sipsolutions.net/mac-gbit/gmac/chipphyforce */
+static void bgmac_phy_force(struct bgmac *bgmac)
+{
+	u16 ctl;
+	u16 mask = ~(BGMAC_PHY_CTL_SPEED | BGMAC_PHY_CTL_SPEED_MSB |
+		     BGMAC_PHY_CTL_ANENAB | BGMAC_PHY_CTL_DUPLEX);
+
+	if (bgmac->phyaddr == BGMAC_PHY_NOREGS)
+		return;
+
+	if (bgmac->autoneg)
+		return;
+
+	ctl = bgmac_phy_read(bgmac, bgmac->phyaddr, BGMAC_PHY_CTL);
+	ctl &= mask;
+	if (bgmac->full_duplex)
+		ctl |= BGMAC_PHY_CTL_DUPLEX;
+	if (bgmac->speed == BGMAC_SPEED_100)
+		ctl |= BGMAC_PHY_CTL_SPEED_100;
+	else if (bgmac->speed == BGMAC_SPEED_1000)
+		ctl |= BGMAC_PHY_CTL_SPEED_1000;
+	bgmac_phy_write(bgmac, bgmac->phyaddr, BGMAC_PHY_CTL, ctl);
+}
+
+/* http://bcm-v4.sipsolutions.net/mac-gbit/gmac/chipphyadvertise */
+static void bgmac_phy_advertise(struct bgmac *bgmac)
+{
+	u16 adv;
+
+	if (bgmac->phyaddr == BGMAC_PHY_NOREGS)
+		return;
+
+	if (!bgmac->autoneg)
+		return;
+
+	/* Adv selected 10/100 speeds */
+	adv = bgmac_phy_read(bgmac, bgmac->phyaddr, BGMAC_PHY_ADV);
+	adv &= ~(BGMAC_PHY_ADV_10HALF | BGMAC_PHY_ADV_10FULL |
+		 BGMAC_PHY_ADV_100HALF | BGMAC_PHY_ADV_100FULL);
+	if (!bgmac->full_duplex && bgmac->speed & BGMAC_SPEED_10)
+		adv |= BGMAC_PHY_ADV_10HALF;
+	if (!bgmac->full_duplex && bgmac->speed & BGMAC_SPEED_100)
+		adv |= BGMAC_PHY_ADV_100HALF;
+	if (bgmac->full_duplex && bgmac->speed & BGMAC_SPEED_10)
+		adv |= BGMAC_PHY_ADV_10FULL;
+	if (bgmac->full_duplex && bgmac->speed & BGMAC_SPEED_100)
+		adv |= BGMAC_PHY_ADV_100FULL;
+	bgmac_phy_write(bgmac, bgmac->phyaddr, BGMAC_PHY_ADV, adv);
+
+	/* Adv selected 1000 speeds */
+	adv = bgmac_phy_read(bgmac, bgmac->phyaddr, BGMAC_PHY_ADV2);
+	adv &= ~(BGMAC_PHY_ADV2_1000HALF | BGMAC_PHY_ADV2_1000FULL);
+	if (!bgmac->full_duplex && bgmac->speed & BGMAC_SPEED_1000)
+		adv |= BGMAC_PHY_ADV2_1000HALF;
+	if (bgmac->full_duplex && bgmac->speed & BGMAC_SPEED_1000)
+		adv |= BGMAC_PHY_ADV2_1000FULL;
+	bgmac_phy_write(bgmac, bgmac->phyaddr, BGMAC_PHY_ADV2, adv);
+
+	/* Restart */
+	bgmac_phy_write(bgmac, bgmac->phyaddr, BGMAC_PHY_CTL,
+			bgmac_phy_read(bgmac, bgmac->phyaddr, BGMAC_PHY_CTL) |
+			BGMAC_PHY_CTL_RESTART);
+}
+
+/* http://bcm-v4.sipsolutions.net/mac-gbit/gmac/chipphyinit */
+static void bgmac_phy_init(struct bgmac *bgmac)
+{
+	struct bcma_chipinfo *ci = &bgmac->core->bus->chipinfo;
+	struct bcma_drv_cc *cc = &bgmac->core->bus->drv_cc;
+	u8 i;
+
+	if (ci->id == BCMA_CHIP_ID_BCM5356) {
+		for (i = 0; i < 5; i++) {
+			bgmac_phy_write(bgmac, i, 0x1f, 0x008b);
+			bgmac_phy_write(bgmac, i, 0x15, 0x0100);
+			bgmac_phy_write(bgmac, i, 0x1f, 0x000f);
+			bgmac_phy_write(bgmac, i, 0x12, 0x2aaa);
+			bgmac_phy_write(bgmac, i, 0x1f, 0x000b);
+		}
+	}
+	if ((ci->id == BCMA_CHIP_ID_BCM5357 && ci->pkg != 10) ||
+	    (ci->id == BCMA_CHIP_ID_BCM4749 && ci->pkg != 10) ||
+	    (ci->id == BCMA_CHIP_ID_BCM53572 && ci->pkg != 9)) {
+		bcma_chipco_chipctl_maskset(cc, 2, ~0xc0000000, 0);
+		bcma_chipco_chipctl_maskset(cc, 4, ~0x80000000, 0);
+		for (i = 0; i < 5; i++) {
+			bgmac_phy_write(bgmac, i, 0x1f, 0x000f);
+			bgmac_phy_write(bgmac, i, 0x16, 0x5284);
+			bgmac_phy_write(bgmac, i, 0x1f, 0x000b);
+			bgmac_phy_write(bgmac, i, 0x17, 0x0010);
+			bgmac_phy_write(bgmac, i, 0x1f, 0x000f);
+			bgmac_phy_write(bgmac, i, 0x16, 0x5296);
+			bgmac_phy_write(bgmac, i, 0x17, 0x1073);
+			bgmac_phy_write(bgmac, i, 0x17, 0x9073);
+			bgmac_phy_write(bgmac, i, 0x16, 0x52b6);
+			bgmac_phy_write(bgmac, i, 0x17, 0x9273);
+			bgmac_phy_write(bgmac, i, 0x1f, 0x000b);
+		}
+	}
+}
+
+/* http://bcm-v4.sipsolutions.net/mac-gbit/gmac/chipphyreset */
+static void bgmac_phy_reset(struct bgmac *bgmac)
+{
+	if (bgmac->phyaddr == BGMAC_PHY_NOREGS)
+		return;
+
+	bgmac_phy_write(bgmac, bgmac->phyaddr, BGMAC_PHY_CTL,
+			BGMAC_PHY_CTL_RESET);
+	udelay(100);
+	if (bgmac_phy_read(bgmac, bgmac->phyaddr, BGMAC_PHY_CTL) &
+	    BGMAC_PHY_CTL_RESET)
+		bgmac_err(bgmac, "PHY reset failed\n");
+	bgmac_phy_init(bgmac);
+}
+
+/**************************************************
+ * Chip ops
+ **************************************************/
+
+/* TODO: can we just drop @force? Can we don't reset MAC at all if there is
+ * nothing to change? Try if after stabilizng driver.
+ */
+static void bgmac_cmdcfg_maskset(struct bgmac *bgmac, u32 mask, u32 set,
+				 bool force)
+{
+	u32 cmdcfg = bgmac_read(bgmac, BGMAC_CMDCFG);
+	u32 new_val = (cmdcfg & mask) | set;
+
+	bgmac_set(bgmac, BGMAC_CMDCFG, BGMAC_CMDCFG_SR);
+	udelay(2);
+
+	if (new_val != cmdcfg || force)
+		bgmac_write(bgmac, BGMAC_CMDCFG, new_val);
+
+	bgmac_mask(bgmac, BGMAC_CMDCFG, ~BGMAC_CMDCFG_SR);
+	udelay(2);
+}
+
+static void bgmac_chip_stats_update(struct bgmac *bgmac)
+{
+	int i;
+
+	if (bgmac->core->id.id != BCMA_CORE_4706_MAC_GBIT) {
+		for (i = 0; i < BGMAC_NUM_MIB_TX_REGS; i++)
+			bgmac->mib_tx_regs[i] =
+				bgmac_read(bgmac,
+					   BGMAC_TX_GOOD_OCTETS + (i * 4));
+		for (i = 0; i < BGMAC_NUM_MIB_RX_REGS; i++)
+			bgmac->mib_rx_regs[i] =
+				bgmac_read(bgmac,
+					   BGMAC_RX_GOOD_OCTETS + (i * 4));
+	}
+
+	/* TODO: what else? how to handle BCM4706? */
+}
+
+static void bgmac_clear_mib(struct bgmac *bgmac)
+{
+	int i;
+
+	if (bgmac->core->id.id == BCMA_CORE_4706_MAC_GBIT)
+		return;
+
+	bgmac_set(bgmac, BGMAC_DEV_CTL, BGMAC_DC_MROR);
+	for (i = 0; i < BGMAC_NUM_MIB_TX_REGS; i++)
+		bgmac_read(bgmac, BGMAC_TX_GOOD_OCTETS + (i * 4));
+	for (i = 0; i < BGMAC_NUM_MIB_RX_REGS; i++)
+		bgmac_read(bgmac, BGMAC_RX_GOOD_OCTETS + (i * 4));
+}
+
+/* http://bcm-v4.sipsolutions.net/mac-gbit/gmac/gmac_speed */
+static void bgmac_speed(struct bgmac *bgmac, int speed)
+{
+	u32 mask = ~(BGMAC_CMDCFG_ES_MASK | BGMAC_CMDCFG_HD);
+	u32 set = 0;
+
+	if (speed & BGMAC_SPEED_10)
+		set |= BGMAC_CMDCFG_ES_10;
+	if (speed & BGMAC_SPEED_100)
+		set |= BGMAC_CMDCFG_ES_100;
+	if (speed & BGMAC_SPEED_1000)
+		set |= BGMAC_CMDCFG_ES_1000;
+	if (!bgmac->full_duplex)
+		set |= BGMAC_CMDCFG_HD;
+	bgmac_cmdcfg_maskset(bgmac, mask, set, true);
+}
+
+static void bgmac_miiconfig(struct bgmac *bgmac)
+{
+	u8 imode = (bgmac_read(bgmac, BGMAC_DEV_STATUS) & BGMAC_DS_MM_MASK) >>
+			BGMAC_DS_MM_SHIFT;
+	if (imode == 0 || imode == 1) {
+		if (bgmac->autoneg)
+			bgmac_speed(bgmac, BGMAC_SPEED_100);
+		else
+			bgmac_speed(bgmac, bgmac->speed);
+	}
+}
+
+/* http://bcm-v4.sipsolutions.net/mac-gbit/gmac/chipreset */
+static void bgmac_chip_reset(struct bgmac *bgmac)
+{
+	struct bcma_device *core = bgmac->core;
+	struct bcma_bus *bus = core->bus;
+	struct bcma_chipinfo *ci = &bus->chipinfo;
+	u32 flags = 0;
+	u32 iost;
+	int i;
+
+	if (bcma_core_is_enabled(core)) {
+		if (!bgmac->stats_grabbed) {
+			bgmac_chip_stats_update(bgmac);
+			bgmac->stats_grabbed = true;
+		}
+
+		for (i = 0; i < BGMAC_MAX_TX_RINGS; i++)
+			bgmac_dma_tx_reset(bgmac, &bgmac->tx_ring[i]);
+
+		bgmac_cmdcfg_maskset(bgmac, ~0, BGMAC_CMDCFG_ML, false);
+		udelay(1);
+
+		for (i = 0; i < BGMAC_MAX_RX_RINGS; i++)
+			bgmac_dma_rx_reset(bgmac, &bgmac->rx_ring[i]);
+
+		/* TODO: Clear software multicast filter list */
+	}
+
+	iost = bcma_aread32(core, BCMA_IOST);
+	if ((ci->id == BCMA_CHIP_ID_BCM5357 && ci->pkg == 10) ||
+	    (ci->id == BCMA_CHIP_ID_BCM4749 && ci->pkg == 10) ||
+	    (ci->id == BCMA_CHIP_ID_BCM53572 && ci->pkg == 9))
+		iost &= ~BGMAC_BCMA_IOST_ATTACHED;
+
+	if (iost & BGMAC_BCMA_IOST_ATTACHED) {
+		flags = BGMAC_BCMA_IOCTL_SW_CLKEN;
+		if (!bgmac->has_robosw)
+			flags |= BGMAC_BCMA_IOCTL_SW_RESET;
+	}
+
+	bcma_core_enable(core, flags);
+
+	if (core->id.rev > 2) {
+		bgmac_set(bgmac, BCMA_CLKCTLST, 1 << 8);
+		bgmac_wait_value(bgmac->core, BCMA_CLKCTLST, 1 << 24, 1 << 24,
+				 1000);
+	}
+
+	if (ci->id == BCMA_CHIP_ID_BCM5357 || ci->id == BCMA_CHIP_ID_BCM4749 ||
+	    ci->id == BCMA_CHIP_ID_BCM53572) {
+		struct bcma_drv_cc *cc = &bgmac->core->bus->drv_cc;
+		u8 et_swtype = 0;
+		u8 sw_type = BGMAC_CHIPCTL_1_SW_TYPE_EPHY |
+			     BGMAC_CHIPCTL_1_IF_TYPE_RMII;
+		char buf[2];
+		if (bcm47xx_nvram_getenv("et_swtype", buf, 1) > 0) {
+			if (kstrtou8(buf, 0, &et_swtype))
+				bgmac_err(bgmac, "Failed to parse et_swtype (%s)\n", buf);
+			et_swtype &= 0x0f;
+			et_swtype <<= 4;
+			sw_type = et_swtype;
+		} else if (ci->id == BCMA_CHIP_ID_BCM5357 && ci->pkg == 9) {
+			sw_type = BGMAC_CHIPCTL_1_SW_TYPE_EPHYRMII;
+		} else if (0) {
+			/* TODO */
+		}
+		bcma_chipco_chipctl_maskset(cc, 1,
+					    ~(BGMAC_CHIPCTL_1_IF_TYPE_MASK |
+					      BGMAC_CHIPCTL_1_SW_TYPE_MASK),
+					    sw_type);
+	}
+
+	if (iost & BGMAC_BCMA_IOST_ATTACHED && !bgmac->has_robosw)
+		bcma_awrite32(core, BCMA_IOCTL,
+			      bcma_aread32(core, BCMA_IOCTL) &
+			      ~BGMAC_BCMA_IOCTL_SW_RESET);
+
+	/* http://bcm-v4.sipsolutions.net/mac-gbit/gmac/gmac_reset
+	 * Specs don't say about using BGMAC_CMDCFG_SR, but in this routine
+	 * BGMAC_CMDCFG is read _after_ putting chip in a reset. So it has to
+	 * be keps until taking MAC out of the reset.
+	 */
+	bgmac_cmdcfg_maskset(bgmac,
+			     ~(BGMAC_CMDCFG_TE |
+			       BGMAC_CMDCFG_RE |
+			       BGMAC_CMDCFG_RPI |
+			       BGMAC_CMDCFG_TAI |
+			       BGMAC_CMDCFG_HD |
+			       BGMAC_CMDCFG_ML |
+			       BGMAC_CMDCFG_CFE |
+			       BGMAC_CMDCFG_RL |
+			       BGMAC_CMDCFG_RED |
+			       BGMAC_CMDCFG_PE |
+			       BGMAC_CMDCFG_TPI |
+			       BGMAC_CMDCFG_PAD_EN |
+			       BGMAC_CMDCFG_PF),
+			     BGMAC_CMDCFG_PROM |
+			     BGMAC_CMDCFG_NLC |
+			     BGMAC_CMDCFG_CFE |
+			     BGMAC_CMDCFG_SR,
+			     false);
+
+	bgmac_clear_mib(bgmac);
+	if (core->id.id == BCMA_CORE_4706_MAC_GBIT)
+		bcma_maskset32(bgmac->cmn, BCMA_GMAC_CMN_PHY_CTL, ~0,
+			       BCMA_GMAC_CMN_PC_MTE);
+	else
+		bgmac_set(bgmac, BGMAC_PHY_CNTL, BGMAC_PC_MTE);
+	bgmac_miiconfig(bgmac);
+	bgmac_phy_init(bgmac);
+
+	bgmac->int_status = 0;
+}
+
+static void bgmac_chip_intrs_on(struct bgmac *bgmac)
+{
+	bgmac_write(bgmac, BGMAC_INT_MASK, bgmac->int_mask);
+}
+
+static void bgmac_chip_intrs_off(struct bgmac *bgmac)
+{
+	bgmac_write(bgmac, BGMAC_INT_MASK, 0);
+}
+
+/* http://bcm-v4.sipsolutions.net/mac-gbit/gmac/gmac_enable */
+static void bgmac_enable(struct bgmac *bgmac)
+{
+	struct bcma_chipinfo *ci = &bgmac->core->bus->chipinfo;
+	u32 cmdcfg;
+	u32 mode;
+	u32 rxq_ctl;
+	u32 fl_ctl;
+	u16 bp_clk;
+	u8 mdp;
+
+	cmdcfg = bgmac_read(bgmac, BGMAC_CMDCFG);
+	bgmac_cmdcfg_maskset(bgmac, ~(BGMAC_CMDCFG_TE | BGMAC_CMDCFG_RE),
+			     BGMAC_CMDCFG_SR, true);
+	udelay(2);
+	cmdcfg |= BGMAC_CMDCFG_TE | BGMAC_CMDCFG_RE;
+	bgmac_write(bgmac, BGMAC_CMDCFG, cmdcfg);
+
+	mode = (bgmac_read(bgmac, BGMAC_DEV_STATUS) & BGMAC_DS_MM_MASK) >>
+		BGMAC_DS_MM_SHIFT;
+	if (ci->id != BCMA_CHIP_ID_BCM47162 || mode != 0)
+		bgmac_set(bgmac, BCMA_CLKCTLST, BCMA_CLKCTLST_FORCEHT);
+	if (ci->id == BCMA_CHIP_ID_BCM47162 && mode == 2)
+		bcma_chipco_chipctl_maskset(&bgmac->core->bus->drv_cc, 1, ~0,
+					    BGMAC_CHIPCTL_1_RXC_DLL_BYPASS);
+
+	switch (ci->id) {
+	case BCMA_CHIP_ID_BCM5357:
+	case BCMA_CHIP_ID_BCM4749:
+	case BCMA_CHIP_ID_BCM53572:
+	case BCMA_CHIP_ID_BCM4716:
+	case BCMA_CHIP_ID_BCM47162:
+		fl_ctl = 0x03cb04cb;
+		if (ci->id == BCMA_CHIP_ID_BCM5357 ||
+		    ci->id == BCMA_CHIP_ID_BCM4749 ||
+		    ci->id == BCMA_CHIP_ID_BCM53572)
+			fl_ctl = 0x2300e1;
+		bgmac_write(bgmac, BGMAC_FLOW_CTL_THRESH, fl_ctl);
+		bgmac_write(bgmac, BGMAC_PAUSE_CTL, 0x27fff);
+		break;
+	}
+
+	rxq_ctl = bgmac_read(bgmac, BGMAC_RXQ_CTL);
+	rxq_ctl &= ~BGMAC_RXQ_CTL_MDP_MASK;
+	bp_clk = bcma_pmu_get_bus_clock(&bgmac->core->bus->drv_cc) / 1000000;
+	mdp = (bp_clk * 128 / 1000) - 3;
+	rxq_ctl |= (mdp << BGMAC_RXQ_CTL_MDP_SHIFT);
+	bgmac_write(bgmac, BGMAC_RXQ_CTL, rxq_ctl);
+}
+
+/* http://bcm-v4.sipsolutions.net/mac-gbit/gmac/chipinit */
+static void bgmac_chip_init(struct bgmac *bgmac, bool full_init)
+{
+	struct ssb_sprom *sprom = &bgmac->core->bus->sprom;
+	struct bgmac_dma_ring *ring;
+	u32 tmp;
+	u8 *mac;
+	int i;
+
+	/* 1 interrupt per received frame */
+	bgmac_write(bgmac, BGMAC_INT_RECV_LAZY, 1 << BGMAC_IRL_FC_SHIFT);
+
+	/* enable 802.3x tx flow control (honor received PAUSE frames) */
+	bgmac_cmdcfg_maskset(bgmac, ~BGMAC_CMDCFG_RPI, 0, true);
+
+	if (bgmac->net_dev->flags & IFF_PROMISC)
+		bgmac_cmdcfg_maskset(bgmac, ~0, BGMAC_CMDCFG_PROM, false);
+	else
+		bgmac_warn(bgmac, "Software filtering is not supported yet\n");
+
+	mac = bgmac->core->core_unit ? sprom->et1mac : sprom->et0mac;
+	tmp = (mac[0] << 24) | (mac[1] << 16) | (mac[2] << 8) | mac[3];
+	bgmac_write(bgmac, BGMAC_MACADDR_HIGH, tmp);
+	tmp = (mac[4] << 8) | mac[5];
+	bgmac_write(bgmac, BGMAC_MACADDR_LOW, tmp);
+	memcpy(bgmac->net_dev->dev_addr, mac, 6);
+
+	if (bgmac->loopback)
+		bgmac_cmdcfg_maskset(bgmac, ~0, BGMAC_CMDCFG_ML, true);
+	else
+		bgmac_cmdcfg_maskset(bgmac, ~BGMAC_CMDCFG_ML, 0, true);
+
+	bgmac_write(bgmac, BGMAC_RXMAX_LENGTH, 32 + ETHER_MAX_LEN);
+
+	if (!bgmac->autoneg) {
+		bgmac_speed(bgmac, bgmac->speed);
+		bgmac_phy_force(bgmac);
+	} else if (bgmac->speed) { /* if there is anything to adv */
+		bgmac_phy_advertise(bgmac);
+	}
+
+	if (full_init) {
+		bgmac_dma_init(bgmac);
+		if (1) /* FIXME: is there any case we don't want IRQs? */
+			bgmac_chip_intrs_on(bgmac);
+	} else {
+		for (i = 0; i < BGMAC_MAX_RX_RINGS; i++) {
+			ring = &bgmac->rx_ring[i];
+			bgmac_dma_rx_enable(bgmac, ring);
+		}
+	}
+
+	bgmac_enable(bgmac);
+}
+
+static irqreturn_t bgmac_interrupt(int irq, void *dev_id)
+{
+	struct bgmac *bgmac = netdev_priv(dev_id);
+
+	u32 int_status = bgmac_read(bgmac, BGMAC_INT_STATUS);
+	int_status &= bgmac->int_mask;
+
+	if (!int_status)
+		return IRQ_NONE;
+
+	/* Ack */
+	bgmac_write(bgmac, BGMAC_INT_STATUS, int_status);
+
+	/* Disable new interrupts until handling existing ones */
+	bgmac_chip_intrs_off(bgmac);
+
+	bgmac->int_status = int_status;
+
+	return IRQ_WAKE_THREAD;
+}
+
+static irqreturn_t bgmac_interrupt_thread(int irq, void *dev_id)
+{
+	struct bgmac *bgmac = netdev_priv(dev_id);
+	struct bgmac_dma_ring *ring;
+
+	if (bgmac->int_status & BGMAC_IS_TX0) {
+		ring = &bgmac->tx_ring[0];
+		bgmac_dma_tx_free(bgmac, ring);
+		bgmac->int_status &= ~BGMAC_IS_TX0;
+	}
+
+	if (bgmac->int_status & BGMAC_IS_RX) {
+		ring = &bgmac->rx_ring[0];
+		bgmac_dma_rx_read(bgmac, ring);
+		bgmac->int_status &= ~BGMAC_IS_RX;
+	}
+
+	if (bgmac->int_status) {
+		bgmac_err(bgmac, "Unknown IRQs: 0x%08X\n", bgmac->int_status);
+		bgmac->int_status = 0;
+	}
+
+	bgmac_chip_intrs_on(bgmac);
+	return IRQ_HANDLED;
+}
+
+/**************************************************
+ * net_device ops
+ **************************************************/
+
+static int bgmac_open(struct net_device *net_dev)
+{
+	struct bgmac *bgmac = netdev_priv(net_dev);
+
+	bgmac_chip_reset(bgmac);
+	/* Specs say about reclaiming rings here, but we do that in DMA init */
+	bgmac_chip_init(bgmac, true);
+
+	if (request_threaded_irq(bgmac->core->irq, bgmac_interrupt,
+				 bgmac_interrupt_thread, IRQF_SHARED,
+				 KBUILD_MODNAME, net_dev) < 0)
+		bgmac_err(bgmac, "IRQ request error!\n");
+
+	return 0;
+}
+
+static int bgmac_stop(struct net_device *net_dev)
+{
+	struct bgmac *bgmac = netdev_priv(net_dev);
+
+	bgmac_chip_intrs_off(bgmac);
+
+	free_irq(bgmac->core->irq, net_dev);
+
+	/* TODO */
+
+	return 0;
+}
+
+static int bgmac_ioctl(struct net_device *net_dev, struct ifreq *ifr, int cmd)
+{
+	struct bgmac *bgmac = netdev_priv(net_dev);
+	struct mii_ioctl_data *data = if_mii(ifr);
+
+	switch (cmd) {
+	case SIOCGMIIPHY:
+		data->phy_id = bgmac->phyaddr;
+		/* fallthru */
+	case SIOCGMIIREG:
+		if (!netif_running(net_dev))
+			return -EAGAIN;
+		data->val_out = bgmac_phy_read(bgmac, data->phy_id,
+					       data->reg_num & 0x1f);
+		return 0;
+	case SIOCSMIIREG:
+		if (!netif_running(net_dev))
+			return -EAGAIN;
+		bgmac_phy_write(bgmac, data->phy_id, data->reg_num & 0x1f,
+				data->val_in);
+		return 0;
+	default:
+		return -EOPNOTSUPP;
+	}
+}
+
+static netdev_tx_t bgmac_start_xmit(struct sk_buff *skb,
+				    struct net_device *net_dev)
+{
+	struct bgmac *bgmac = netdev_priv(net_dev);
+	struct bgmac_dma_ring *ring;
+
+	/* No QOS support yet */
+	ring = &bgmac->tx_ring[0];
+	return bgmac_dma_tx_add(bgmac, ring, skb);
+}
+
+static const struct net_device_ops bgmac_netdev_ops = {
+	.ndo_open		= bgmac_open,
+	.ndo_stop		= bgmac_stop,
+	.ndo_do_ioctl           = bgmac_ioctl,
+	.ndo_start_xmit		= bgmac_start_xmit,
+};
+
+/**************************************************
+ * BCMA bus ops
+ **************************************************/
+
+/* http://bcm-v4.sipsolutions.net/mac-gbit/gmac/chipattach */
+static int bgmac_probe(struct bcma_device *core)
+{
+	struct net_device *net_dev;
+	struct bgmac *bgmac;
+	struct ssb_sprom *sprom = &core->bus->sprom;
+	int err;
+
+	/* Allocation and references */
+	net_dev = alloc_etherdev(sizeof(*bgmac));
+	if (!net_dev)
+		return -ENOMEM;
+	net_dev->netdev_ops = &bgmac_netdev_ops;
+	net_dev->irq = core->irq;
+	bgmac = netdev_priv(net_dev);
+	bgmac->net_dev = net_dev;
+	bgmac->core = core;
+	bcma_set_drvdata(core, bgmac);
+
+	/* Defaults */
+	bgmac->autoneg = true;
+	bgmac->full_duplex = true;
+	bgmac->speed = BGMAC_SPEED_10 | BGMAC_SPEED_100 | BGMAC_SPEED_1000;
+
+	/* On BCM4706 we need common core to access PHY */
+	if (core->id.id == BCMA_CORE_4706_MAC_GBIT &&
+	    !core->bus->drv_gmac_cmn.core) {
+		bgmac_err(bgmac, "GMAC CMN core not found (required for BCM4706)\n");
+		return -ENODEV;
+	}
+	bgmac->cmn = core->bus->drv_gmac_cmn.core;
+
+	bgmac->phyaddr = core->core_unit ? sprom->et1phyaddr :
+			 sprom->et0phyaddr;
+	bgmac->phyaddr &= BGMAC_PHY_MASK;
+	if (bgmac->phyaddr == BGMAC_PHY_MASK) {
+		bgmac_err(bgmac, "No PHY found\n");
+		return -ENODEV;
+	}
+	bgmac_info(bgmac, "Found PHY addr: %d\n", bgmac->phyaddr);
+
+	if (core->bus->hosttype == BCMA_HOSTTYPE_PCI) {
+		bgmac_err(bgmac, "PCI setup not implemented\n");
+		return -ENOTSUPP;
+	}
+
+	bgmac_chip_reset(bgmac);
+
+	bgmac_dma_alloc(bgmac);
+
+	bgmac->int_mask = BGMAC_IS_ERRMASK | BGMAC_IS_RX | BGMAC_IS_TX_MASK;
+	if (bcm47xx_nvram_getenv("et0_no_txint", NULL, 0) > 0)
+		bgmac->int_mask &= ~BGMAC_IS_TX_MASK;
+
+	/* TODO: reset the external phy */
+	bgmac_phy_reset(bgmac);
+
+	bgmac->has_robosw = !!(core->bus->sprom.boardflags_lo &
+			       BGMAC_BFL_ENETROBO);
+	if (bgmac->has_robosw)
+		bgmac_err(bgmac, "Support for Roboswitch not implemented\n");
+
+	if (core->bus->sprom.boardflags_lo & BGMAC_BFL_ENETADM)
+		bgmac_err(bgmac, "Support for ADMtek ethernet switch not implemented\n");
+
+	err = register_netdev(bgmac->net_dev);
+	if (err) {
+		bgmac_err(bgmac, "Cannot register net device\n");
+		return -ENOTSUPP;
+	}
+
+	return 0;
+}
+
+static void bgmac_remove(struct bcma_device *core)
+{
+	struct bgmac *bgmac = bcma_get_drvdata(core);
+
+	unregister_netdev(bgmac->net_dev);
+	free_netdev(bgmac->net_dev);
+	bcma_set_drvdata(core, NULL);
+}
+
+static struct bcma_driver bgmac_bcma_driver = {
+	.name		= KBUILD_MODNAME,
+	.id_table	= bgmac_bcma_tbl,
+	.probe		= bgmac_probe,
+	.remove		= bgmac_remove,
+};
+
+static int __init bgmac_init(void)
+{
+	int err;
+
+	err = bcma_driver_register(&bgmac_bcma_driver);
+	if (err)
+		return err;
+	pr_info("Broadcom 47xx GMAC driver loaded\n");
+
+	return 0;
+}
+
+static void __exit bgmac_exit(void)
+{
+	bcma_driver_unregister(&bgmac_bcma_driver);
+}
+
+module_init(bgmac_init)
+module_exit(bgmac_exit)
--- /dev/null
+++ b/drivers/net/ethernet/broadcom/bgmac.h
@@ -0,0 +1,424 @@
+#ifndef _BGMAC_H
+#define _BGMAC_H
+
+#include <linux/bcma/bcma.h>
+
+#define BGMAC_DEV_CTL				0x000
+#define  BGMAC_DC_TSM				0x00000002
+#define  BGMAC_DC_CFCO				0x00000004
+#define  BGMAC_DC_RLSS				0x00000008
+#define  BGMAC_DC_MROR				0x00000010
+#define  BGMAC_DC_FCM_MASK			0x00000060
+#define  BGMAC_DC_FCM_SHIFT			5
+#define  BGMAC_DC_NAE				0x00000080
+#define  BGMAC_DC_TF				0x00000100
+#define  BGMAC_DC_RDS_MASK			0x00030000
+#define  BGMAC_DC_RDS_SHIFT			16
+#define  BGMAC_DC_TDS_MASK			0x000c0000
+#define  BGMAC_DC_TDS_SHIFT			18
+#define BGMAC_DEV_STATUS			0x004		/* Configuration of the interface */
+#define  BGMAC_DS_RBF				0x00000001
+#define  BGMAC_DS_RDF				0x00000002
+#define  BGMAC_DS_RIF				0x00000004
+#define  BGMAC_DS_TBF				0x00000008
+#define  BGMAC_DS_TDF				0x00000010
+#define  BGMAC_DS_TIF				0x00000020
+#define  BGMAC_DS_PO				0x00000040
+#define  BGMAC_DS_MM_MASK			0x00000300	/* Mode of the interface */
+#define  BGMAC_DS_MM_SHIFT			8
+#define BGMAC_BIST_STATUS			0x00c
+#define BGMAC_INT_STATUS			0x020		/* Interrupt status */
+#define  BGMAC_IS_MRO				0x00000001
+#define  BGMAC_IS_MTO				0x00000002
+#define  BGMAC_IS_TFD				0x00000004
+#define  BGMAC_IS_LS				0x00000008
+#define  BGMAC_IS_MDIO				0x00000010
+#define  BGMAC_IS_MR				0x00000020
+#define  BGMAC_IS_MT				0x00000040
+#define  BGMAC_IS_TO				0x00000080
+#define  BGMAC_IS_DESC_ERR			0x00000400	/* Descriptor error */
+#define  BGMAC_IS_DATA_ERR			0x00000800	/* Data error */
+#define  BGMAC_IS_DESC_PROT_ERR			0x00001000	/* Descriptor protocol error */
+#define  BGMAC_IS_RX_DESC_UNDERF		0x00002000	/* Receive descriptor underflow */
+#define  BGMAC_IS_RX_F_OVERF			0x00004000	/* Receive fifi overflow */
+#define  BGMAC_IS_TX_F_UNDERF			0x00008000	/* Transmit fifo underflow */
+#define  BGMAC_IS_RX				0x00010000	/* Interrupt for RX queue 0 */
+#define  BGMAC_IS_TX0				0x01000000	/* Interrupt for TX queue 0 */
+#define  BGMAC_IS_TX1				0x02000000	/* Interrupt for TX queue 1 */
+#define  BGMAC_IS_TX2				0x04000000	/* Interrupt for TX queue 2 */
+#define  BGMAC_IS_TX3				0x08000000	/* Interrupt for TX queue 3 */
+#define  BGMAC_IS_TX_MASK			0x0f000000
+#define  BGMAC_IS_INTMASK			0x0f01fcff
+#define  BGMAC_IS_ERRMASK			0x0000fc00
+#define BGMAC_INT_MASK				0x024		/* Interrupt mask */
+#define BGMAC_GP_TIMER				0x028
+#define BGMAC_INT_RECV_LAZY			0x100
+#define  BGMAC_IRL_TO_MASK			0x00ffffff
+#define  BGMAC_IRL_FC_MASK			0xff000000
+#define  BGMAC_IRL_FC_SHIFT			24		/* Shift the number of interrupts triggered per received frame */
+#define BGMAC_FLOW_CTL_THRESH			0x104		/* Flow control thresholds */
+#define BGMAC_WRRTHRESH				0x108
+#define BGMAC_GMAC_IDLE_CNT_THRESH		0x10c
+#define BGMAC_PHY_ACCESS			0x180		/* PHY access address */
+#define  BGMAC_PA_DATA_MASK			0x0000ffff
+#define  BGMAC_PA_ADDR_MASK			0x001f0000
+#define  BGMAC_PA_ADDR_SHIFT			16
+#define  BGMAC_PA_REG_MASK			0x1f000000
+#define  BGMAC_PA_REG_SHIFT			24
+#define  BGMAC_PA_WRITE				0x20000000
+#define  BGMAC_PA_START				0x40000000
+#define BGMAC_PHY_CNTL				0x188		/* PHY control address */
+#define  BGMAC_PC_EPA_MASK			0x0000001f
+#define  BGMAC_PC_MCT_MASK			0x007f0000
+#define  BGMAC_PC_MCT_SHIFT			16
+#define  BGMAC_PC_MTE				0x00800000
+#define BGMAC_TXQ_CTL				0x18c
+#define  BGMAC_TXQ_CTL_DBT_MASK			0x00000fff
+#define  BGMAC_TXQ_CTL_DBT_SHIFT		0
+#define BGMAC_RXQ_CTL				0x190
+#define  BGMAC_RXQ_CTL_DBT_MASK			0x00000fff
+#define  BGMAC_RXQ_CTL_DBT_SHIFT		0
+#define  BGMAC_RXQ_CTL_PTE			0x00001000
+#define  BGMAC_RXQ_CTL_MDP_MASK			0x3f000000
+#define  BGMAC_RXQ_CTL_MDP_SHIFT		24
+#define BGMAC_GPIO_SELECT			0x194
+#define BGMAC_GPIO_OUTPUT_EN			0x198
+/* For 0x1e0 see BCMA_CLKCTLST */
+#define BGMAC_HW_WAR				0x1e4
+#define BGMAC_PWR_CTL				0x1e8
+#define BGMAC_DMA_BASE0				0x200		/* Tx and Rx controller */
+#define BGMAC_DMA_BASE1				0x240		/* Tx controller only */
+#define BGMAC_DMA_BASE2				0x280		/* Tx controller only */
+#define BGMAC_DMA_BASE3				0x2C0		/* Tx controller only */
+#define BGMAC_TX_GOOD_OCTETS			0x300
+#define BGMAC_TX_GOOD_OCTETS_HIGH		0x304
+#define BGMAC_TX_GOOD_PKTS			0x308
+#define BGMAC_TX_OCTETS				0x30c
+#define BGMAC_TX_OCTETS_HIGH			0x310
+#define BGMAC_TX_PKTS				0x314
+#define BGMAC_TX_BROADCAST_PKTS			0x318
+#define BGMAC_TX_MULTICAST_PKTS			0x31c
+#define BGMAC_TX_LEN_64				0x320
+#define BGMAC_TX_LEN_65_TO_127			0x324
+#define BGMAC_TX_LEN_128_TO_255			0x328
+#define BGMAC_TX_LEN_256_TO_511			0x32c
+#define BGMAC_TX_LEN_512_TO_1023		0x330
+#define BGMAC_TX_LEN_1024_TO_1522		0x334
+#define BGMAC_TX_LEN_1523_TO_2047		0x338
+#define BGMAC_TX_LEN_2048_TO_4095		0x33c
+#define BGMAC_TX_LEN_4095_TO_8191		0x340
+#define BGMAC_TX_LEN_8192_TO_MAX		0x344
+#define BGMAC_TX_JABBER_PKTS			0x348		/* Error */
+#define BGMAC_TX_OVERSIZE_PKTS			0x34c		/* Error */
+#define BGMAC_TX_FRAGMENT_PKTS			0x350
+#define BGMAC_TX_UNDERRUNS			0x354		/* Error */
+#define BGMAC_TX_TOTAL_COLS			0x358
+#define BGMAC_TX_SINGLE_COLS			0x35c
+#define BGMAC_TX_MULTIPLE_COLS			0x360
+#define BGMAC_TX_EXCESSIVE_COLS			0x364		/* Error */
+#define BGMAC_TX_LATE_COLS			0x368		/* Error */
+#define BGMAC_TX_DEFERED			0x36c
+#define BGMAC_TX_CARRIER_LOST			0x370
+#define BGMAC_TX_PAUSE_PKTS			0x374
+#define BGMAC_TX_UNI_PKTS			0x378
+#define BGMAC_TX_Q0_PKTS			0x37c
+#define BGMAC_TX_Q0_OCTETS			0x380
+#define BGMAC_TX_Q0_OCTETS_HIGH			0x384
+#define BGMAC_TX_Q1_PKTS			0x388
+#define BGMAC_TX_Q1_OCTETS			0x38c
+#define BGMAC_TX_Q1_OCTETS_HIGH			0x390
+#define BGMAC_TX_Q2_PKTS			0x394
+#define BGMAC_TX_Q2_OCTETS			0x398
+#define BGMAC_TX_Q2_OCTETS_HIGH			0x39c
+#define BGMAC_TX_Q3_PKTS			0x3a0
+#define BGMAC_TX_Q3_OCTETS			0x3a4
+#define BGMAC_TX_Q3_OCTETS_HIGH			0x3a8
+#define BGMAC_RX_GOOD_OCTETS			0x3b0
+#define BGMAC_RX_GOOD_OCTETS_HIGH		0x3b4
+#define BGMAC_RX_GOOD_PKTS			0x3b8
+#define BGMAC_RX_OCTETS				0x3bc
+#define BGMAC_RX_OCTETS_HIGH			0x3c0
+#define BGMAC_RX_PKTS				0x3c4
+#define BGMAC_RX_BROADCAST_PKTS			0x3c8
+#define BGMAC_RX_MULTICAST_PKTS			0x3cc
+#define BGMAC_RX_LEN_64				0x3d0
+#define BGMAC_RX_LEN_65_TO_127			0x3d4
+#define BGMAC_RX_LEN_128_TO_255			0x3d8
+#define BGMAC_RX_LEN_256_TO_511			0x3dc
+#define BGMAC_RX_LEN_512_TO_1023		0x3e0
+#define BGMAC_RX_LEN_1024_TO_1522		0x3e4
+#define BGMAC_RX_LEN_1523_TO_2047		0x3e8
+#define BGMAC_RX_LEN_2048_TO_4095		0x3ec
+#define BGMAC_RX_LEN_4095_TO_8191		0x3f0
+#define BGMAC_RX_LEN_8192_TO_MAX		0x3f4
+#define BGMAC_RX_JABBER_PKTS			0x3f8		/* Error */
+#define BGMAC_RX_OVERSIZE_PKTS			0x3fc		/* Error */
+#define BGMAC_RX_FRAGMENT_PKTS			0x400
+#define BGMAC_RX_MISSED_PKTS			0x404		/* Error */
+#define BGMAC_RX_CRC_ALIGN_ERRS			0x408		/* Error */
+#define BGMAC_RX_UNDERSIZE			0x40c		/* Error */
+#define BGMAC_RX_CRC_ERRS			0x410		/* Error */
+#define BGMAC_RX_ALIGN_ERRS			0x414		/* Error */
+#define BGMAC_RX_SYMBOL_ERRS			0x418		/* Error */
+#define BGMAC_RX_PAUSE_PKTS			0x41c
+#define BGMAC_RX_NONPAUSE_PKTS			0x420
+#define BGMAC_RX_SACHANGES			0x424
+#define BGMAC_RX_UNI_PKTS			0x428
+#define BGMAC_UNIMAC_VERSION			0x800
+#define BGMAC_HDBKP_CTL				0x804
+#define BGMAC_CMDCFG				0x808		/* Configuration */
+#define  BGMAC_CMDCFG_TE			0x00000001	/* Set to activate TX */
+#define  BGMAC_CMDCFG_RE			0x00000002	/* Set to activate RX */
+#define  BGMAC_CMDCFG_ES_MASK			0x0000000c	/* Ethernet speed see gmac_speed */
+#define   BGMAC_CMDCFG_ES_10			0x00000000
+#define   BGMAC_CMDCFG_ES_100			0x00000004
+#define   BGMAC_CMDCFG_ES_1000			0x00000008
+#define  BGMAC_CMDCFG_PROM			0x00000010	/* Set to activate promiscuous mode */
+#define  BGMAC_CMDCFG_PAD_EN			0x00000020
+#define  BGMAC_CMDCFG_CF			0x00000040
+#define  BGMAC_CMDCFG_PF			0x00000080
+#define  BGMAC_CMDCFG_RPI			0x00000100	/* Unset to enable 802.3x tx flow control */
+#define  BGMAC_CMDCFG_TAI			0x00000200
+#define  BGMAC_CMDCFG_HD			0x00000400	/* Set if in half duplex mode */
+#define  BGMAC_CMDCFG_HD_SHIFT			10
+#define  BGMAC_CMDCFG_SR			0x00000800	/* Set to reset mode */
+#define  BGMAC_CMDCFG_ML			0x00008000	/* Set to activate mac loopback mode */
+#define  BGMAC_CMDCFG_AE			0x00400000
+#define  BGMAC_CMDCFG_CFE			0x00800000
+#define  BGMAC_CMDCFG_NLC			0x01000000
+#define  BGMAC_CMDCFG_RL			0x02000000
+#define  BGMAC_CMDCFG_RED			0x04000000
+#define  BGMAC_CMDCFG_PE			0x08000000
+#define  BGMAC_CMDCFG_TPI			0x10000000
+#define  BGMAC_CMDCFG_AT			0x20000000
+#define BGMAC_MACADDR_HIGH			0x80c		/* High 4 octets of own mac address */
+#define BGMAC_MACADDR_LOW			0x810		/* Low 2 octets of own mac address */
+#define BGMAC_RXMAX_LENGTH			0x814		/* Max receive frame length with vlan tag */
+#define BGMAC_PAUSEQUANTA			0x818
+#define BGMAC_MAC_MODE				0x844
+#define BGMAC_OUTERTAG				0x848
+#define BGMAC_INNERTAG				0x84c
+#define BGMAC_TXIPG				0x85c
+#define BGMAC_PAUSE_CTL				0xb30
+#define BGMAC_TX_FLUSH				0xb34
+#define BGMAC_RX_STATUS				0xb38
+#define BGMAC_TX_STATUS				0xb3c
+
+#define BGMAC_PHY_CTL				0x00
+#define  BGMAC_PHY_CTL_SPEED_MSB		0x0040
+#define  BGMAC_PHY_CTL_DUPLEX			0x0100		/* duplex mode */
+#define  BGMAC_PHY_CTL_RESTART			0x0200		/* restart autonegotiation */
+#define  BGMAC_PHY_CTL_ANENAB			0x1000		/* enable autonegotiation */
+#define  BGMAC_PHY_CTL_SPEED			0x2000
+#define  BGMAC_PHY_CTL_LOOP			0x4000		/* loopback */
+#define  BGMAC_PHY_CTL_RESET			0x8000		/* reset */
+/* Helpers */
+#define  BGMAC_PHY_CTL_SPEED_10			0
+#define  BGMAC_PHY_CTL_SPEED_100		BGMAC_PHY_CTL_SPEED
+#define  BGMAC_PHY_CTL_SPEED_1000		BGMAC_PHY_CTL_SPEED_MSB
+#define BGMAC_PHY_ADV				0x04
+#define  BGMAC_PHY_ADV_10HALF			0x0020		/* advertise 10MBits/s half duplex */
+#define  BGMAC_PHY_ADV_10FULL			0x0040		/* advertise 10MBits/s full duplex */
+#define  BGMAC_PHY_ADV_100HALF			0x0080		/* advertise 100MBits/s half duplex */
+#define  BGMAC_PHY_ADV_100FULL			0x0100		/* advertise 100MBits/s full duplex */
+#define BGMAC_PHY_ADV2				0x09
+#define  BGMAC_PHY_ADV2_1000HALF		0x0100		/* advertise 1000MBits/s half duplex */
+#define  BGMAC_PHY_ADV2_1000FULL		0x0200		/* advertise 1000MBits/s full duplex */
+
+/* BCMA GMAC core specific IO Control (BCMA_IOCTL) flags */
+#define BGMAC_BCMA_IOCTL_SW_CLKEN		0x00000004	/* PHY Clock Enable */
+#define BGMAC_BCMA_IOCTL_SW_RESET		0x00000008	/* PHY Reset */
+
+/* BCMA GMAC core specific IO status (BCMA_IOST) flags */
+#define BGMAC_BCMA_IOST_ATTACHED		0x00000800
+
+#define BGMAC_NUM_MIB_TX_REGS	\
+		(((BGMAC_TX_Q3_OCTETS_HIGH - BGMAC_TX_GOOD_OCTETS) / 4) + 1)
+#define BGMAC_NUM_MIB_RX_REGS	\
+		(((BGMAC_RX_UNI_PKTS - BGMAC_RX_GOOD_OCTETS) / 4) + 1)
+
+#define BGMAC_DMA_TX_CTL			0x00
+#define  BGMAC_DMA_TX_ENABLE			0x00000001
+#define  BGMAC_DMA_TX_SUSPEND			0x00000002
+#define  BGMAC_DMA_TX_LOOPBACK			0x00000004
+#define  BGMAC_DMA_TX_FLUSH			0x00000010
+#define  BGMAC_DMA_TX_PARITY_DISABLE		0x00000800
+#define  BGMAC_DMA_TX_ADDREXT_MASK		0x00030000
+#define  BGMAC_DMA_TX_ADDREXT_SHIFT		16
+#define BGMAC_DMA_TX_INDEX			0x04
+#define BGMAC_DMA_TX_RINGLO			0x08
+#define BGMAC_DMA_TX_RINGHI			0x0C
+#define BGMAC_DMA_TX_STATUS			0x10
+#define  BGMAC_DMA_TX_STATDPTR			0x00001FFF
+#define  BGMAC_DMA_TX_STAT			0xF0000000
+#define   BGMAC_DMA_TX_STAT_DISABLED		0x00000000
+#define   BGMAC_DMA_TX_STAT_ACTIVE		0x10000000
+#define   BGMAC_DMA_TX_STAT_IDLEWAIT		0x20000000
+#define   BGMAC_DMA_TX_STAT_STOPPED		0x30000000
+#define   BGMAC_DMA_TX_STAT_SUSP		0x40000000
+#define BGMAC_DMA_TX_ERROR			0x14
+#define  BGMAC_DMA_TX_ERRDPTR			0x0001FFFF
+#define  BGMAC_DMA_TX_ERR			0xF0000000
+#define   BGMAC_DMA_TX_ERR_NOERR		0x00000000
+#define   BGMAC_DMA_TX_ERR_PROT			0x10000000
+#define   BGMAC_DMA_TX_ERR_UNDERRUN		0x20000000
+#define   BGMAC_DMA_TX_ERR_TRANSFER		0x30000000
+#define   BGMAC_DMA_TX_ERR_DESCREAD		0x40000000
+#define   BGMAC_DMA_TX_ERR_CORE			0x50000000
+#define BGMAC_DMA_RX_CTL			0x20
+#define  BGMAC_DMA_RX_ENABLE			0x00000001
+#define  BGMAC_DMA_RX_FRAME_OFFSET_MASK		0x000000FE
+#define  BGMAC_DMA_RX_FRAME_OFFSET_SHIFT	1
+#define  BGMAC_DMA_RX_DIRECT_FIFO		0x00000100
+#define  BGMAC_DMA_RX_OVERFLOW_CONT		0x00000400
+#define  BGMAC_DMA_RX_PARITY_DISABLE		0x00000800
+#define  BGMAC_DMA_RX_ADDREXT_MASK		0x00030000
+#define  BGMAC_DMA_RX_ADDREXT_SHIFT		16
+#define BGMAC_DMA_RX_INDEX			0x24
+#define BGMAC_DMA_RX_RINGLO			0x28
+#define BGMAC_DMA_RX_RINGHI			0x2C
+#define BGMAC_DMA_RX_STATUS			0x30
+#define  BGMAC_DMA_RX_STATDPTR			0x00001FFF
+#define  BGMAC_DMA_RX_STAT			0xF0000000
+#define   BGMAC_DMA_RX_STAT_DISABLED		0x00000000
+#define   BGMAC_DMA_RX_STAT_ACTIVE		0x10000000
+#define   BGMAC_DMA_RX_STAT_IDLEWAIT		0x20000000
+#define   BGMAC_DMA_RX_STAT_STOPPED		0x30000000
+#define   BGMAC_DMA_RX_STAT_SUSP		0x40000000
+#define BGMAC_DMA_RX_ERROR			0x34
+#define  BGMAC_DMA_RX_ERRDPTR			0x0001FFFF
+#define  BGMAC_DMA_RX_ERR			0xF0000000
+#define   BGMAC_DMA_RX_ERR_NOERR		0x00000000
+#define   BGMAC_DMA_RX_ERR_PROT			0x10000000
+#define   BGMAC_DMA_RX_ERR_UNDERRUN		0x20000000
+#define   BGMAC_DMA_RX_ERR_TRANSFER		0x30000000
+#define   BGMAC_DMA_RX_ERR_DESCREAD		0x40000000
+#define   BGMAC_DMA_RX_ERR_CORE			0x50000000
+
+#define BGMAC_DESC_CTL0_EOT			0x10000000	/* End of ring */
+#define BGMAC_DESC_CTL0_IOC			0x20000000	/* IRQ on complete */
+#define BGMAC_DESC_CTL0_SOF			0x40000000	/* Start of frame */
+#define BGMAC_DESC_CTL0_EOF			0x80000000	/* End of frame */
+#define BGMAC_DESC_CTL1_LEN			0x00001FFF
+
+#define BGMAC_PHY_NOREGS			0x1E
+#define BGMAC_PHY_MASK				0x1F
+
+#define BGMAC_MAX_TX_RINGS			4
+#define BGMAC_MAX_RX_RINGS			1
+
+#define BGMAC_TX_RING_SLOTS			128
+#define BGMAC_RX_RING_SLOTS			512 - 1		/* Why -1? Well, Broadcom does that... */
+
+#define BGMAC_RX_HEADER_LEN			28		/* Last 24 bytes are unused. Well... */
+#define BGMAC_RX_FRAME_OFFSET			30		/* There are 2 unused bytes between header and real data */
+#define BGMAC_RX_MAX_FRAME_SIZE			1536		/* Copied from b44/tg3 */
+#define BGMAC_RX_BUF_SIZE			(BGMAC_RX_FRAME_OFFSET + BGMAC_RX_MAX_FRAME_SIZE)
+
+#define BGMAC_BFL_ENETROBO			0x0010		/* has ephy roboswitch spi */
+#define BGMAC_BFL_ENETADM			0x0080		/* has ADMtek switch */
+#define BGMAC_BFL_ENETVLAN			0x0100		/* can do vlan */
+
+#define BGMAC_CHIPCTL_1_IF_TYPE_MASK		0x00000030
+#define BGMAC_CHIPCTL_1_IF_TYPE_RMII		0x00000000
+#define BGMAC_CHIPCTL_1_IF_TYPE_MI		0x00000010
+#define BGMAC_CHIPCTL_1_IF_TYPE_RGMII		0x00000020
+#define BGMAC_CHIPCTL_1_SW_TYPE_MASK		0x000000C0
+#define BGMAC_CHIPCTL_1_SW_TYPE_EPHY		0x00000000
+#define BGMAC_CHIPCTL_1_SW_TYPE_EPHYMII		0x00000040
+#define BGMAC_CHIPCTL_1_SW_TYPE_EPHYRMII	0x00000080
+#define BGMAC_CHIPCTL_1_SW_TYPE_RGMI		0x000000C0
+#define BGMAC_CHIPCTL_1_RXC_DLL_BYPASS		0x00010000
+
+#define BGMAC_SPEED_10				0x0001
+#define BGMAC_SPEED_100				0x0002
+#define BGMAC_SPEED_1000			0x0004
+
+struct bgmac_slot_info {
+	struct sk_buff *skb;
+	dma_addr_t dma_addr;
+};
+
+struct bgmac_dma_desc {
+	__le32 ctl0;
+	__le32 ctl1;
+	__le32 addr_low;
+	__le32 addr_high;
+} __packed;
+
+struct bgmac_dma_ring {
+	bool tx;
+	u16 num_slots;
+	u16 start;
+	u16 end;
+
+	u16 mmio_base;
+	void *cpu_base;
+	dma_addr_t dma_base;
+
+	struct bgmac_slot_info slots[BGMAC_RX_RING_SLOTS];
+};
+
+struct bgmac_rx_header {
+	__le16 len;
+	__le16 flags;
+	__le16 pad[12];
+};
+
+struct bgmac {
+	struct bcma_device *core;
+	struct bcma_device *cmn; /* Reference to CMN core for BCM4706 */
+	struct net_device *net_dev;
+
+	u8 phyaddr;
+	bool has_robosw;
+
+	u32 int_mask;
+	u32 int_status;
+
+	bool loopback;
+
+	bool autoneg;
+	bool full_duplex;
+	int speed;
+
+	/* DMA */
+	struct bgmac_dma_ring tx_ring[BGMAC_MAX_TX_RINGS];
+	struct bgmac_dma_ring rx_ring[BGMAC_MAX_RX_RINGS];
+
+	/* Stats */
+	bool stats_grabbed;
+	u32 mib_tx_regs[BGMAC_NUM_MIB_TX_REGS];
+	u32 mib_rx_regs[BGMAC_NUM_MIB_RX_REGS];
+};
+
+static inline u32 bgmac_read(struct bgmac *bgmac, u16 offset)
+{
+	return bcma_read32(bgmac->core, offset);
+}
+
+static inline void bgmac_write(struct bgmac *bgmac, u16 offset, u32 value)
+{
+	bcma_write32(bgmac->core, offset, value);
+}
+
+static inline void bgmac_maskset(struct bgmac *bgmac, u16 offset, u32 mask,
+				   u32 set)
+{
+	bgmac_write(bgmac, offset, (bgmac_read(bgmac, offset) & mask) | set);
+}
+
+static inline void bgmac_mask(struct bgmac *bgmac, u16 offset, u32 mask)
+{
+	bgmac_maskset(bgmac, offset, mask, 0);
+}
+
+static inline void bgmac_set(struct bgmac *bgmac, u16 offset, u32 set)
+{
+	bgmac_maskset(bgmac, offset, ~0, set);
+}
+
+u16 bgmac_phy_read(struct bgmac *bgmac, u8 phyaddr, u8 reg);
+void bgmac_phy_write(struct bgmac *bgmac, u8 phyaddr, u8 reg, u16 value);
+
+#endif /* _BGMAC_H */
--- a/include/linux/bcma/bcma_driver_chipcommon.h
+++ b/include/linux/bcma/bcma_driver_chipcommon.h
@@ -627,4 +627,6 @@ int bcma_nflash_erase(struct bcma_drv_cc
 int bcma_nflash_commit(struct bcma_drv_cc *cc, u32 offset, u32 len, const u8 *buf);
 #endif
 
+extern u32 bcma_pmu_get_bus_clock(struct bcma_drv_cc *cc);
+
 #endif /* LINUX_BCMA_DRIVER_CC_H_ */