Linux version 2.4.30 (nthill@debian) (gcc version 3.4.4) #2 Sat Aug 13 01:30:32 CEST 2005
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
 BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 0000000008000000 (usable)
 BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
128MB LOWMEM available.
On node 0 totalpages: 32768
zone(0): 4096 pages.
zone(1): 28672 pages.
zone(2): 0 pages.
DMI not present.
Kernel command line: blkmtd_device=/dev/hda2 root=/dev/mtdblock0 init=/etc/preinit noinitrd console=ttyS0,19200n8 
Initializing CPU#0
Detected 266.650 MHz processor.
Calibrating delay loop... 532.48 BogoMIPS
Memory: 127284k/131072k available (1238k kernel code, 3400k reserved, 248k data, 80k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Dentry cache hash table entries: 16384 (order: 5, 131072 bytes)
Inode cache hash table entries: 8192 (order: 4, 65536 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 8192 (order: 3, 32768 bytes)
Page-cache hash table entries: 32768 (order: 5, 131072 bytes)
CPU:     After generic, caps: 00808131 00818131 00000000 00000001
CPU:             Common caps: 00808131 00818131 00000000 00000001
CPU: NSC Unknown stepping 01
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
PCI: PCI BIOS revision 2.01 entry at 0xf7861, last bus=0
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
JFFS2 version 2.1. (C) 2001 Red Hat, Inc., designed by Axis Communications AB.
Squashfs 2.1-r2 (released 2004/12/15) (C) 2002-2004 Phillip Lougher
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
Software Watchdog Timer: 0.05, timer margin: 60 sec
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
SC1200: IDE controller at PCI slot 00:12.2
SC1200: chipset revision 1
SC1200: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0xe000-0xe007, BIOS settings: hda:pio, hdb:pio
    ide1: BM-DMA at 0xe008-0xe00f, BIOS settings: hdc:pio, hdd:pio
hda: Transcend 256M, CFA DISK drive
hdb: HTS424030M9AT00, ATA DISK drive
SC1200: set xfer mode failure
hdb: sc1200_set_xfer_mode(UDMA 2)
blk: queue c02c421c, I/O limit 4095Mb (mask 0xffffffff)
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: attached ide-disk driver.
hda: 500736 sectors (256 MB) w/2KiB Cache, CHS=978/16/32
hdb: attached ide-disk driver.
hdb: host protected area => 1
hdb: 58605120 sectors (30006 MB) w/1739KiB Cache, CHS=3648/255/63, UDMA(33)
Partition check:
 /dev/ide/host0/bus0/target0/lun0: p1 p2 p3 p4
 /dev/ide/host0/bus0/target1/lun0: p1 p2 p3
 /dev/ide/host0/bus0/target0/lun0: p1 p2 p3 p4
blkmtd: mtd0: [/dev/hda2] erase_size = 128KiB 
blkmtd: version 1.10
Initializing Cryptographic API
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 1024 buckets, 8Kbytes
TCP: Hash tables configured (established 8192 bind 16384)
ip_conntrack version 2.1 (5953 buckets, 5953 max) - 316 bytes per conntrack
ip_tables: (C) 2000-2002 Netfilter core team
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
NET4: Ethernet Bridge 008 for NET4.0
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (jffs2 filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 80k freed
jffs2.bbc: SIZE compression mode activated.
natsemi dp8381x driver, version 1.07+LK1.0.17, Sep 27, 2002
  originally by Donald Becker <becker@scyld.com>
  http://www.scyld.com/network/natsemi.html
  2.4.x kernel port by Jeff Garzik, Tjeerd Mulder
eth0: NatSemi DP8381[56] at 0xc88ab000, 00:00:24:c2:45:7c, IRQ 10.
eth1: NatSemi DP8381[56] at 0xc88ad000, 00:00:24:c2:45:7d, IRQ 10.
eth2: NatSemi DP8381[56] at 0xc88af000, 00:00:24:c2:45:7e, IRQ 10.
device eth0 entered promiscuous mode
eth0: link up.
eth0: Setting full-duplex based on negotiated link capability.
eth0: Promiscuous mode enabled.
eth0: Promiscuous mode enabled.
eth0: Promiscuous mode enabled.
eth0: Promiscuous mode enabled.
eth0: Promiscuous mode enabled.
br0: port 1(eth0) entering learning state
br0: port 1(eth0) entering forwarding state
br0: topology change detected, propagating