From 553786683f6d1316f38c7459fb17f3f88e9c553d Mon Sep 17 00:00:00 2001
From: blogic <blogic@3c298f89-4303-0410-b956-a3cf2f4a3e73>
Date: Sat, 15 Dec 2012 02:01:08 +0000
Subject: [lantiq] remove 3.3 and 3.6
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@34699 3c298f89-4303-0410-b956-a3cf2f4a3e73
---
.../files-3.3/drivers/i2c/busses/i2c-falcon.c | 1040 --------------------
1 file changed, 1040 deletions(-)
delete mode 100644 target/linux/lantiq/files-3.3/drivers/i2c/busses/i2c-falcon.c
(limited to 'target/linux/lantiq/files-3.3/drivers/i2c')
diff --git a/target/linux/lantiq/files-3.3/drivers/i2c/busses/i2c-falcon.c b/target/linux/lantiq/files-3.3/drivers/i2c/busses/i2c-falcon.c
deleted file mode 100644
index f97ddb601..000000000
--- a/target/linux/lantiq/files-3.3/drivers/i2c/busses/i2c-falcon.c
+++ /dev/null
@@ -1,1040 +0,0 @@
-/*
- * Lantiq FALC(tm) ON - I2C bus adapter
- *
- * Parts based on i2c-designware.c and other i2c drivers from Linux 2.6.33
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
- *
- * Copyright (C) 2010 Thomas Langer <thomas.langer@lantiq.com>
- */
-
-/*
- * CURRENT ISSUES:
- * - no high speed support
- * - supports only master mode
- * - ten bit mode is not tested (no slave devices)
- */
-
-#include <linux/kernel.h>
-#include <linux/module.h>
-#include <linux/delay.h>
-#include <linux/slab.h>
-#include <linux/i2c.h>
-#include <linux/clk.h>
-#include <linux/errno.h>
-#include <linux/sched.h>
-#include <linux/err.h>
-#include <linux/interrupt.h>
-#include <linux/platform_device.h>
-#include <linux/io.h>
-#include <linux/err.h>
-#include <linux/gpio.h>
-
-#include <lantiq_soc.h>
-
-/* I2C Identification Register */
-/* Module ID */
-#define I2C_ID_ID_MASK 0x0000FF00
-/* field offset */
-#define I2C_ID_ID_OFFSET 8
-/* Revision */
-#define I2C_ID_REV_MASK 0x000000FF
-/* field offset */
-#define I2C_ID_REV_OFFSET 0
-
-/* I2C Error Interrupt Request Source Status Register */
-/* TXF_OFL */
-#define I2C_ERR_IRQSS_TXF_OFL 0x00000008
-/* TXF_UFL */
-#define I2C_ERR_IRQSS_TXF_UFL 0x00000004
-/* RXF_OFL */
-#define I2C_ERR_IRQSS_RXF_OFL 0x00000002
-/* RXF_UFL */
-#define I2C_ERR_IRQSS_RXF_UFL 0x00000001
-
-/* I2C Bus Status Register */
-/* Bus Status */
-#define I2C_BUS_STAT_BS_MASK 0x00000003
-/* I2C Bus is free. */
-#define I2C_BUS_STAT_BS_FREE 0x00000000
-/*
- * The device is working as master and has claimed the control
- * on the I2C-bus (busy master).
- */
-#define I2C_BUS_STAT_BS_BM 0x00000002
-
-/* I2C Interrupt Clear Register */
-/* Clear */
-#define I2C_ICR_BREQ_INT_CLR 0x00000008
-/* Clear */
-#define I2C_ICR_LBREQ_INT_CLR 0x00000004
-
-/* I2C RUN Control Register */
-/* Enable */
-#define I2C_RUN_CTRL_RUN_EN 0x00000001
-
-/* I2C Kernel Clock Control Register */
-/* field offset */
-#define I2C_CLC_RMC_OFFSET 8
-/* Enable */
-#define I2C_IMSC_I2C_P_INT_EN 0x00000020
-/* Enable */
-#define I2C_IMSC_I2C_ERR_INT_EN 0x00000010
-/* Enable */
-#define I2C_IMSC_BREQ_INT_EN 0x00000008
-/* Enable */
-#define I2C_IMSC_LBREQ_INT_EN 0x00000004
-
-/* I2C Fractional Divider Configuration Register */
-/* field offset */
-#define I2C_FDIV_CFG_INC_OFFSET 16
-/* field offset */
-#define I2C_FDIV_CFG_DEC_OFFSET 0
-
-/* I2C Fractional Divider (highspeed mode) Configuration Register */
-/* field offset */
-#define I2C_FDIV_HIGH_CFG_INC_OFFSET 16
-/* field offset */
-#define I2C_FDIV_HIGH_CFG_DEC_OFFSET 0
-
-/* I2C Address Register */
-/* Enable */
-#define I2C_ADDR_CFG_SOPE_EN 0x00200000
-/* Enable */
-#define I2C_ADDR_CFG_SONA_EN 0x00100000
-/* Enable */
-#define I2C_ADDR_CFG_MnS_EN 0x00080000
-
-/* I2C Protocol Interrupt Request Source Status Register */
-/* RX */
-#define I2C_P_IRQSS_RX 0x00000040
-/* TX_END */
-#define I2C_P_IRQSS_TX_END 0x00000020
-/* NACK */
-#define I2C_P_IRQSS_NACK 0x00000010
-/* AL */
-#define I2C_P_IRQSS_AL 0x00000008
-
-/* I2C Raw Interrupt Status Register */
-/* Read: Interrupt occurred. */
-#define I2C_RIS_I2C_P_INT_INTOCC 0x00000020
-/* Read: Interrupt occurred. */
-#define I2C_RIS_I2C_ERR_INT_INTOCC 0x00000010
-
-/* I2C End Data Control Register */
-/*
- * Set End of Transmission - Note: Do not write '1' to this bit when bus is
- * free. This will cause an abort after the first byte when a new transfer
- * is started.
- */
-#define I2C_ENDD_CTRL_SETEND 0x00000002
-/* TX FIFO Flow Control */
-#define I2C_FIFO_CFG_TXFC 0x00020000
-/* RX FIFO Flow Control */
-#define I2C_FIFO_CFG_RXFC 0x00010000
-/* Word aligned (character alignment of four characters) */
-#define I2C_FIFO_CFG_TXFA_TXFA2 0x00002000
-/* Word aligned (character alignment of four characters) */
-#define I2C_FIFO_CFG_RXFA_RXFA2 0x00000200
-/* 1 word */
-#define I2C_FIFO_CFG_TXBS_TXBS0 0x00000000
-/* 1 word */
-#define I2C_FIFO_CFG_RXBS_RXBS0 0x00000000
-
-
-/* I2C register structure */
-struct gpon_reg_i2c {
- /* I2C Kernel Clock Control Register */
- unsigned int clc; /* 0x00000000 */
- /* Reserved */
- unsigned int res_0; /* 0x00000004 */
- /* I2C Identification Register */
- unsigned int id; /* 0x00000008 */
- /* Reserved */
- unsigned int res_1; /* 0x0000000C */
- /*
- * I2C RUN Control Register - This register enables and disables the I2C
- * peripheral. Before enabling, the I2C has to be configured properly.
- * After enabling no configuration is possible
- */
- unsigned int run_ctrl; /* 0x00000010 */
- /*
- * I2C End Data Control Register - This register is used to either turn
- * around the data transmission direction or to address another slave
- * without sending a stop condition. Also the software can stop the
- * slave-transmitter by sending a not-accolade when working as
- * master-receiver or even stop data transmission immediately when
- * operating as master-transmitter. The writing to the bits of this
- * control register is only effective when in MASTER RECEIVES BYTES,
- * MASTER TRANSMITS BYTES, MASTER RESTART or SLAVE RECEIVE BYTES state
- */
- unsigned int endd_ctrl; /* 0x00000014 */
- /*
- * I2C Fractional Divider Configuration Register - These register is
- * used to program the fractional divider of the I2C bus. Before the
- * peripheral is switched on by setting the RUN-bit the two (fixed)
- * values for the two operating frequencies are programmed into these
- * (configuration) registers. The Register FDIV_HIGH_CFG has the same
- * layout as I2C_FDIV_CFG.
- */
- unsigned int fdiv_cfg; /* 0x00000018 */
- /*
- * I2C Fractional Divider (highspeed mode) Configuration Register
- * These register is used to program the fractional divider of the I2C
- * bus. Before the peripheral is switched on by setting the RUN-bit the
- * two (fixed) values for the two operating frequencies are programmed
- * into these (configuration) registers. The Register FDIV_CFG has the
- * same layout as I2C_FDIV_CFG.
- */
- unsigned int fdiv_high_cfg; /* 0x0000001C */
- /* I2C Address Configuration Register */
- unsigned int addr_cfg; /* 0x00000020 */
- /*
- * I2C Bus Status Register - This register gives a status information
- * of the I2C. This additional information can be used by the software
- * to start proper actions.
- */
- unsigned int bus_stat; /* 0x00000024 */
- /* I2C FIFO Configuration Register */
- unsigned int fifo_cfg; /* 0x00000028 */
- /* I2C Maximum Received Packet Size Register */
- unsigned int mrps_ctrl; /* 0x0000002C */
- /* I2C Received Packet Size Status Register */
- unsigned int rps_stat; /* 0x00000030 */
- /* I2C Transmit Packet Size Register */
- unsigned int tps_ctrl; /* 0x00000034 */
- /* I2C Filled FIFO Stages Status Register */
- unsigned int ffs_stat; /* 0x00000038 */
- /* Reserved */
- unsigned int res_2; /* 0x0000003C */
- /* I2C Timing Configuration Register */
- unsigned int tim_cfg; /* 0x00000040 */
- /* Reserved */
- unsigned int res_3[7]; /* 0x00000044 */
- /* I2C Error Interrupt Request Source Mask Register */
- unsigned int err_irqsm; /* 0x00000060 */
- /* I2C Error Interrupt Request Source Status Register */
- unsigned int err_irqss; /* 0x00000064 */
- /* I2C Error Interrupt Request Source Clear Register */
- unsigned int err_irqsc; /* 0x00000068 */
- /* Reserved */
- unsigned int res_4; /* 0x0000006C */
- /* I2C Protocol Interrupt Request Source Mask Register */
- unsigned int p_irqsm; /* 0x00000070 */
- /* I2C Protocol Interrupt Request Source Status Register */
- unsigned int p_irqss; /* 0x00000074 */
- /* I2C Protocol Interrupt Request Source Clear Register */
- unsigned int p_irqsc; /* 0x00000078 */
- /* Reserved */
- unsigned int res_5; /* 0x0000007C */
- /* I2C Raw Interrupt Status Register */
- unsigned int ris; /* 0x00000080 */
- /* I2C Interrupt Mask Control Register */
- unsigned int imsc; /* 0x00000084 */
- /* I2C Masked Interrupt Status Register */
- unsigned int mis; /* 0x00000088 */
- /* I2C Interrupt Clear Register */
- unsigned int icr; /* 0x0000008C */
- /* I2C Interrupt Set Register */
- unsigned int isr; /* 0x00000090 */
- /* I2C DMA Enable Register */
- unsigned int dmae; /* 0x00000094 */
- /* Reserved */
- unsigned int res_6[8154]; /* 0x00000098 */
- /* I2C Transmit Data Register */
- unsigned int txd; /* 0x00008000 */
- /* Reserved */
- unsigned int res_7[4095]; /* 0x00008004 */
- /* I2C Receive Data Register */
- unsigned int rxd; /* 0x0000C000 */
- /* Reserved */
- unsigned int res_8[4095]; /* 0x0000C004 */
-};
-
-/* mapping for access macros */
-#define i2c ((struct gpon_reg_i2c *)priv->membase)
-#define reg_r32(reg) __raw_readl(reg)
-#define reg_w32(val, reg) __raw_writel(val, reg)
-#define reg_w32_mask(clear, set, reg) \
- reg_w32((reg_r32(reg) & ~(clear)) | (set), reg)
-#define reg_r32_table(reg, idx) reg_r32(&((uint32_t *)®)[idx])
-#define reg_w32_table(val, reg, idx) reg_w32(val, &((uint32_t *)®)[idx])
-
-#define i2c_r32(reg) reg_r32(&i2c->reg)
-#define i2c_w32(val, reg) reg_w32(val, &i2c->reg)
-#define i2c_w32_mask(clear, set, reg) reg_w32_mask(clear, set, &i2c->reg)
-
-#define DRV_NAME "i2c-falcon"
-#define DRV_VERSION "1.01"
-
-#define FALCON_I2C_BUSY_TIMEOUT 20 /* ms */
-
-#ifdef DEBUG
-#define FALCON_I2C_XFER_TIMEOUT (25 * HZ)
-#else
-#define FALCON_I2C_XFER_TIMEOUT HZ
-#endif
-#if defined(DEBUG) && 0
-#define PRINTK(arg...) pr_info(arg)
-#else
-#define PRINTK(arg...) do {} while (0)
-#endif
-
-#define FALCON_I2C_IMSC_DEFAULT_MASK (I2C_IMSC_I2C_P_INT_EN | \
- I2C_IMSC_I2C_ERR_INT_EN)
-
-#define FALCON_I2C_ARB_LOST (1 << 0)
-#define FALCON_I2C_NACK (1 << 1)
-#define FALCON_I2C_RX_UFL (1 << 2)
-#define FALCON_I2C_RX_OFL (1 << 3)
-#define FALCON_I2C_TX_UFL (1 << 4)
-#define FALCON_I2C_TX_OFL (1 << 5)
-
-struct falcon_i2c {
- struct mutex mutex;
-
- enum {
- FALCON_I2C_MODE_100 = 1,
- FALCON_I2C_MODE_400 = 2,
- FALCON_I2C_MODE_3400 = 3
- } mode; /* current speed mode */
-
- struct clk *clk; /* clock input for i2c hardware block */
- struct gpon_reg_i2c __iomem *membase; /* base of mapped registers */
- int irq_lb, irq_b, irq_err, irq_p; /* last burst, burst, error,
- protocol IRQs */
-
- struct i2c_adapter adap;
- struct device *dev;
-
- struct completion cmd_complete;
-
- /* message transfer data */
- /* current message */
- struct i2c_msg *current_msg;
- /* number of messages to handle */
- int msgs_num;
- /* current buffer */
- u8 *msg_buf;
- /* remaining length of current buffer */
- u32 msg_buf_len;
- /* error status of the current transfer */
- int msg_err;
-
- /* master status codes */
- enum {
- STATUS_IDLE,
- STATUS_ADDR, /* address phase */
- STATUS_WRITE,
- STATUS_READ,
- STATUS_READ_END,
- STATUS_STOP
- } status;
-};
-
-static irqreturn_t falcon_i2c_isr(int irq, void *dev_id);
-
-static inline void enable_burst_irq(struct falcon_i2c *priv)
-{
- i2c_w32_mask(0, I2C_IMSC_LBREQ_INT_EN | I2C_IMSC_BREQ_INT_EN, imsc);
-}
-static inline void disable_burst_irq(struct falcon_i2c *priv)
-{
- i2c_w32_mask(I2C_IMSC_LBREQ_INT_EN | I2C_IMSC_BREQ_INT_EN, 0, imsc);
-}
-
-static void prepare_msg_send_addr(struct falcon_i2c *priv)
-{
- struct i2c_msg *msg = priv->current_msg;
- int rd = !!(msg->flags & I2C_M_RD);
- u16 addr = msg->addr;
-
- /* new i2c_msg */
- priv->msg_buf = msg->buf;
- priv->msg_buf_len = msg->len;
- if (rd)
- priv->status = STATUS_READ;
- else
- priv->status = STATUS_WRITE;
-
- /* send slave address */
- if (msg->flags & I2C_M_TEN) {
- i2c_w32(0xf0 | ((addr & 0x300) >> 7) | rd, txd);
- i2c_w32(addr & 0xff, txd);
- } else
- i2c_w32((addr & 0x7f) << 1 | rd, txd);
-}
-
-static void set_tx_len(struct falcon_i2c *priv)
-{
- struct i2c_msg *msg = priv->current_msg;
- int len = (msg->flags & I2C_M_TEN) ? 2 : 1;
-
- PRINTK("set_tx_len %cX\n", (msg->flags & I2C_M_RD) ? ('R') : ('T'));
-
- priv->status = STATUS_ADDR;
-
- if (!(msg->flags & I2C_M_RD)) {
- len += msg->len;
- } else {
- /* set maximum received packet size (before rx int!) */
- i2c_w32(msg->len, mrps_ctrl);
- }
- i2c_w32(len, tps_ctrl);
- enable_burst_irq(priv);
-}
-
-static int falcon_i2c_hw_init(struct i2c_adapter *adap)
-{
- struct falcon_i2c *priv = i2c_get_adapdata(adap);
-
- /* disable bus */
- i2c_w32_mask(I2C_RUN_CTRL_RUN_EN, 0, run_ctrl);
-
-#ifndef DEBUG
- /* set normal operation clock divider */
- i2c_w32(1 << I2C_CLC_RMC_OFFSET, clc);
-#else
- /* for debugging a higher divider value! */
- i2c_w32(0xF0 << I2C_CLC_RMC_OFFSET, clc);
-#endif
-
- /* set frequency */
- if (priv->mode == FALCON_I2C_MODE_100) {
- dev_dbg(priv->dev, "set standard mode (100 kHz)\n");
- i2c_w32(0, fdiv_high_cfg);
- i2c_w32((1 << I2C_FDIV_CFG_INC_OFFSET) |
- (499 << I2C_FDIV_CFG_DEC_OFFSET),
- fdiv_cfg);
- } else if (priv->mode == FALCON_I2C_MODE_400) {
- dev_dbg(priv->dev, "set fast mode (400 kHz)\n");
- i2c_w32(0, fdiv_high_cfg);
- i2c_w32((1 << I2C_FDIV_CFG_INC_OFFSET) |
- (124 << I2C_FDIV_CFG_DEC_OFFSET),
- fdiv_cfg);
- } else if (priv->mode == FALCON_I2C_MODE_3400) {
- dev_dbg(priv->dev, "set high mode (3.4 MHz)\n");
- i2c_w32(0, fdiv_cfg);
- /* TODO recalculate value for 100MHz input */
- i2c_w32((41 << I2C_FDIV_HIGH_CFG_INC_OFFSET) |
- (152 << I2C_FDIV_HIGH_CFG_DEC_OFFSET),
- fdiv_high_cfg);
- } else {
- dev_warn(priv->dev, "unknown mode\n");
- return -ENODEV;
- }
-
- /* configure fifo */
- i2c_w32(I2C_FIFO_CFG_TXFC | /* tx fifo as flow controller */
- I2C_FIFO_CFG_RXFC | /* rx fifo as flow controller */
- I2C_FIFO_CFG_TXFA_TXFA2 | /* tx fifo 4-byte aligned */
- I2C_FIFO_CFG_RXFA_RXFA2 | /* rx fifo 4-byte aligned */
- I2C_FIFO_CFG_TXBS_TXBS0 | /* tx fifo burst size is 1 word */
- I2C_FIFO_CFG_RXBS_RXBS0, /* rx fifo burst size is 1 word */
- fifo_cfg);
-
- /* configure address */
- i2c_w32(I2C_ADDR_CFG_SOPE_EN | /* generate stop when no more data
- in the fifo */
- I2C_ADDR_CFG_SONA_EN | /* generate stop when NA received */
- I2C_ADDR_CFG_MnS_EN | /* we are master device */
- 0, /* our slave address (not used!) */
- addr_cfg);
-
- /* enable bus */
- i2c_w32_mask(0, I2C_RUN_CTRL_RUN_EN, run_ctrl);
-
- return 0;
-}
-
-static int falcon_i2c_wait_bus_not_busy(struct falcon_i2c *priv)
-{
- int timeout = FALCON_I2C_BUSY_TIMEOUT;
-
- while ((i2c_r32(bus_stat) & I2C_BUS_STAT_BS_MASK)
- != I2C_BUS_STAT_BS_FREE) {
- if (timeout <= 0) {
- dev_warn(priv->dev, "timeout waiting for bus ready\n");
- return -ETIMEDOUT;
- }
- timeout--;
- mdelay(1);
- }
-
- return 0;
-}
-
-static void falcon_i2c_tx(struct falcon_i2c *priv, int last)
-{
- if (priv->msg_buf_len && priv->msg_buf) {
- i2c_w32(*priv->msg_buf, txd);
-
- if (--priv->msg_buf_len)
- priv->msg_buf++;
- else
- priv->msg_buf = NULL;
- } else
- last = 1;
-
- if (last)
- disable_burst_irq(priv);
-}
-
-static void falcon_i2c_rx(struct falcon_i2c *priv, int last)
-{
- u32 fifo_stat, timeout;
- if (priv->msg_buf_len && priv->msg_buf) {
- timeout = 5000000;
- do {
- fifo_stat = i2c_r32(ffs_stat);
- } while (!fifo_stat && --timeout);
- if (!timeout) {
- last = 1;
- PRINTK("\nrx timeout\n");
- goto err;
- }
- while (fifo_stat) {
- *priv->msg_buf = i2c_r32(rxd);
- if (--priv->msg_buf_len)
- priv->msg_buf++;
- else {
- priv->msg_buf = NULL;
- last = 1;
- break;
- }
- #if 0
- fifo_stat = i2c_r32(ffs_stat);
- #else
- /* do not read more than burst size, otherwise no "last
- burst" is generated and the transaction is blocked! */
- fifo_stat = 0;
- #endif
- }
- } else {
- last = 1;
- }
-err:
- if (last) {
- disable_burst_irq(priv);
-
- if (priv->status == STATUS_READ_END) {
- /* do the STATUS_STOP and complete() here, as sometimes
- the tx_end is already seen before this is finished */
- priv->status = STATUS_STOP;
- complete(&priv->cmd_complete);
- } else {
- i2c_w32(I2C_ENDD_CTRL_SETEND, endd_ctrl);
- priv->status = STATUS_READ_END;
- }
- }
-}
-
-static void falcon_i2c_xfer_init(struct falcon_i2c *priv)
-{
- /* enable interrupts */
- i2c_w32(FALCON_I2C_IMSC_DEFAULT_MASK, imsc);
-
- /* trigger transfer of first msg */
- set_tx_len(priv);
-}
-
-static void dump_msgs(struct i2c_msg msgs[], int num, int rx)
-{
-#if defined(DEBUG)
- int i, j;
- pr_info("Messages %d %s\n", num, rx ? "out" : "in");
- for (i = 0; i < num; i++) {
- pr_info("%2d %cX Msg(%d) addr=0x%X: ", i,
- (msgs[i].flags & I2C_M_RD) ? ('R') : ('T'),
- msgs[i].len, msgs[i].addr);
- if (!(msgs[i].flags & I2C_M_RD) || rx) {
- for (j = 0; j < msgs[i].len; j++)
- printk("%02X ", msgs[i].buf[j]);
- }
- printk("\n");
- }
-#endif
-}
-
-static void falcon_i2c_release_bus(struct falcon_i2c *priv)
-{
- if ((i2c_r32(bus_stat) & I2C_BUS_STAT_BS_MASK) == I2C_BUS_STAT_BS_BM)
- i2c_w32(I2C_ENDD_CTRL_SETEND, endd_ctrl);
-}
-
-static int falcon_i2c_xfer(struct i2c_adapter *adap, struct i2c_msg msgs[],
- int num)
-{
- struct falcon_i2c *priv = i2c_get_adapdata(adap);
- int ret;
-
- dev_dbg(priv->dev, "xfer %u messages\n", num);
- dump_msgs(msgs, num, 0);
-
- mutex_lock(&priv->mutex);
-
- INIT_COMPLETION(priv->cmd_complete);
- priv->current_msg = msgs;
- priv->msgs_num = num;
- priv->msg_err = 0;
- priv->status = STATUS_IDLE;
-
- /* wait for the bus to become ready */
- ret = falcon_i2c_wait_bus_not_busy(priv);
- if (ret)
- goto done;
-
- while (priv->msgs_num) {
- /* start the transfers */
- falcon_i2c_xfer_init(priv);
-
- /* wait for transfers to complete */
- ret = wait_for_completion_interruptible_timeout(
- &priv->cmd_complete, FALCON_I2C_XFER_TIMEOUT);
- if (ret == 0) {
- dev_err(priv->dev, "controller timed out\n");
- falcon_i2c_hw_init(adap);
- ret = -ETIMEDOUT;
- goto done;
- } else if (ret < 0)
- goto done;
-
- if (priv->msg_err) {
- if (priv->msg_err & FALCON_I2C_NACK)
- ret = -ENXIO;
- else
- ret = -EREMOTEIO;
- goto done;
- }
- if (--priv->msgs_num)
- priv->current_msg++;
- }
- /* no error? */
- ret = num;
-
-done:
- falcon_i2c_release_bus(priv);
-
- mutex_unlock(&priv->mutex);
-
- if (ret >= 0)
- dump_msgs(msgs, num, 1);
-
- PRINTK("XFER ret %d\n", ret);
- return ret;
-}
-
-static irqreturn_t falcon_i2c_isr_burst(int irq, void *dev_id)
-{
- struct falcon_i2c *priv = dev_id;
- struct i2c_msg *msg = priv->current_msg;
- int last = (irq == priv->irq_lb);
-
- if (last)
- PRINTK("LB ");
- else
- PRINTK("B ");
-
- if (msg->flags & I2C_M_RD) {
- switch (priv->status) {
- case STATUS_ADDR:
- PRINTK("X");
- prepare_msg_send_addr(priv);
- disable_burst_irq(priv);
- break;
- case STATUS_READ:
- case STATUS_READ_END:
- PRINTK("R");
- falcon_i2c_rx(priv, last);
- break;
- default:
- disable_burst_irq(priv);
- PRINTK("Status R %d\n", priv->status);
- break;
- }
- } else {
- switch (priv->status) {
- case STATUS_ADDR:
- PRINTK("x");
- prepare_msg_send_addr(priv);
- break;
- case STATUS_WRITE:
- PRINTK("w");
- falcon_i2c_tx(priv, last);
- break;
- default:
- disable_burst_irq(priv);
- PRINTK("Status W %d\n", priv->status);
- break;
- }
- }
-
- i2c_w32(I2C_ICR_BREQ_INT_CLR | I2C_ICR_LBREQ_INT_CLR, icr);
- return IRQ_HANDLED;
-}
-
-static void falcon_i2c_isr_prot(struct falcon_i2c *priv)
-{
- u32 i_pro = i2c_r32(p_irqss);
-
- PRINTK("i2c-p");
-
- /* not acknowledge */
- if (i_pro & I2C_P_IRQSS_NACK) {
- priv->msg_err |= FALCON_I2C_NACK;
- PRINTK(" nack");
- }
-
- /* arbitration lost */
- if (i_pro & I2C_P_IRQSS_AL) {
- priv->msg_err |= FALCON_I2C_ARB_LOST;
- PRINTK(" arb-lost");
- }
- /* tx -> rx switch */
- if (i_pro & I2C_P_IRQSS_RX)
- PRINTK(" rx");
-
- /* tx end */
- if (i_pro & I2C_P_IRQSS_TX_END)
- PRINTK(" txend");
- PRINTK("\n");
-
- if (!priv->msg_err) {
- /* tx -> rx switch */
- if (i_pro & I2C_P_IRQSS_RX) {
- priv->status = STATUS_READ;
- enable_burst_irq(priv);
- }
- if (i_pro & I2C_P_IRQSS_TX_END) {
- if (priv->status == STATUS_READ)
- priv->status = STATUS_READ_END;
- else {
- disable_burst_irq(priv);
- priv->status = STATUS_STOP;
- }
- }
- }
-
- i2c_w32(i_pro, p_irqsc);
-}
-
-static irqreturn_t falcon_i2c_isr(int irq, void *dev_id)
-{
- u32 i_raw, i_err = 0;
- struct falcon_i2c *priv = dev_id;
-
- i_raw = i2c_r32(mis);
- PRINTK("i_raw 0x%08X\n", i_raw);
-
- /* error interrupt */
- if (i_raw & I2C_RIS_I2C_ERR_INT_INTOCC) {
- i_err = i2c_r32(err_irqss);
- PRINTK("i_err 0x%08X bus_stat 0x%04X\n",
- i_err, i2c_r32(bus_stat));
-
- /* tx fifo overflow (8) */
- if (i_err & I2C_ERR_IRQSS_TXF_OFL)
- priv->msg_err |= FALCON_I2C_TX_OFL;
-
- /* tx fifo underflow (4) */
- if (i_err & I2C_ERR_IRQSS_TXF_UFL)
- priv->msg_err |= FALCON_I2C_TX_UFL;
-
- /* rx fifo overflow (2) */
- if (i_err & I2C_ERR_IRQSS_RXF_OFL)
- priv->msg_err |= FALCON_I2C_RX_OFL;
-
- /* rx fifo underflow (1) */
- if (i_err & I2C_ERR_IRQSS_RXF_UFL)
- priv->msg_err |= FALCON_I2C_RX_UFL;
-
- i2c_w32(i_err, err_irqsc);
- }
-
- /* protocol interrupt */
- if (i_raw & I2C_RIS_I2C_P_INT_INTOCC)
- falcon_i2c_isr_prot(priv);
-
- if ((priv->msg_err) || (priv->status == STATUS_STOP))
- complete(&priv->cmd_complete);
-
- return IRQ_HANDLED;
-}
-
-static u32 falcon_i2c_functionality(struct i2c_adapter *adap)
-{
- return I2C_FUNC_I2C |
- I2C_FUNC_10BIT_ADDR |
- I2C_FUNC_SMBUS_EMUL;
-}
-
-static struct i2c_algorithm falcon_i2c_algorithm = {
- .master_xfer = falcon_i2c_xfer,
- .functionality = falcon_i2c_functionality,
-};
-
-static int __devinit falcon_i2c_probe(struct platform_device *pdev)
-{
- int ret = 0;
- struct falcon_i2c *priv;
- struct i2c_adapter *adap;
- struct resource *mmres, *ioarea,
- *irqres_lb, *irqres_b, *irqres_err, *irqres_p;
- struct clk *clk;
-
- dev_dbg(&pdev->dev, "probing\n");
-
- mmres = platform_get_resource(pdev, IORESOURCE_MEM, 0);
- irqres_lb = platform_get_resource_byname(pdev, IORESOURCE_IRQ,
- "i2c_lb");
- irqres_b = platform_get_resource_byname(pdev, IORESOURCE_IRQ, "i2c_b");
- irqres_err = platform_get_resource_byname(pdev, IORESOURCE_IRQ,
- "i2c_err");
- irqres_p = platform_get_resource_byname(pdev, IORESOURCE_IRQ, "i2c_p");
-
- if (!mmres || !irqres_lb || !irqres_b || !irqres_err || !irqres_p) {
- dev_err(&pdev->dev, "no resources\n");
- return -ENODEV;
- }
-
- clk = clk_get_fpi();
- if (IS_ERR(clk)) {
- dev_err(&pdev->dev, "failed to get fpi clk\n");
- return -ENOENT;
- }
-
- if (clk_get_rate(clk) != 100000000) {
- dev_err(&pdev->dev, "input clock is not 100MHz\n");
- return -ENOENT;
- }
- clk = clk_get(&pdev->dev, NULL);
- if (IS_ERR(clk)) {
- dev_err(&pdev->dev, "failed to get i2c clk\n");
- return -ENOENT;
- }
- clk_activate(clk);
- /* allocate private data */
- priv = kzalloc(sizeof(*priv), GFP_KERNEL);
- if (!priv) {
- dev_err(&pdev->dev, "can't allocate private data\n");
- return -ENOMEM;
- }
-
- adap = &priv->adap;
- i2c_set_adapdata(adap, priv);
- adap->owner = THIS_MODULE;
- adap->class = I2C_CLASS_HWMON | I2C_CLASS_SPD;
- strlcpy(adap->name, DRV_NAME "-adapter", sizeof(adap->name));
- adap->algo = &falcon_i2c_algorithm;
-
- priv->mode = FALCON_I2C_MODE_100;
- priv->clk = clk;
- priv->dev = &pdev->dev;
-
- init_completion(&priv->cmd_complete);
- mutex_init(&priv->mutex);
-
- if (ltq_gpio_request(&pdev->dev, 107, 0, 0, DRV_NAME":sda") ||
- ltq_gpio_request(&pdev->dev, 108, 0, 0, DRV_NAME":scl"))
- {
- dev_err(&pdev->dev, "I2C gpios not available\n");
- ret = -ENXIO;
- goto err_free_priv;
- }
-
- ioarea = request_mem_region(mmres->start, resource_size(mmres),
- pdev->name);
-
- if (ioarea == NULL) {
- dev_err(&pdev->dev, "I2C region already claimed\n");
- ret = -ENXIO;
- goto err_free_gpio;
- }
-
- /* map memory */
- priv->membase = ioremap_nocache(mmres->start & ~KSEG1,
- resource_size(mmres));
- if (priv->membase == NULL) {
- ret = -ENOMEM;
- goto err_release_region;
- }
-
- priv->irq_lb = irqres_lb->start;
- ret = request_irq(priv->irq_lb, falcon_i2c_isr_burst, IRQF_DISABLED,
- irqres_lb->name, priv);
- if (ret) {
- dev_err(&pdev->dev, "can't get last burst IRQ %d\n",
- irqres_lb->start);
- ret = -ENODEV;
- goto err_unmap_mem;
- }
-
- priv->irq_b = irqres_b->start;
- ret = request_irq(priv->irq_b, falcon_i2c_isr_burst, IRQF_DISABLED,
- irqres_b->name, priv);
- if (ret) {
- dev_err(&pdev->dev, "can't get burst IRQ %d\n",
- irqres_b->start);
- ret = -ENODEV;
- goto err_free_lb_irq;
- }
-
- priv->irq_err = irqres_err->start;
- ret = request_irq(priv->irq_err, falcon_i2c_isr, IRQF_DISABLED,
- irqres_err->name, priv);
- if (ret) {
- dev_err(&pdev->dev, "can't get error IRQ %d\n",
- irqres_err->start);
- ret = -ENODEV;
- goto err_free_b_irq;
- }
-
- priv->irq_p = irqres_p->start;
- ret = request_irq(priv->irq_p, falcon_i2c_isr, IRQF_DISABLED,
- irqres_p->name, priv);
- if (ret) {
- dev_err(&pdev->dev, "can't get protocol IRQ %d\n",
- irqres_p->start);
- ret = -ENODEV;
- goto err_free_err_irq;
- }
-
- dev_dbg(&pdev->dev, "mapped io-space to %p\n", priv->membase);
- dev_dbg(&pdev->dev, "use IRQs %d, %d, %d, %d\n", irqres_lb->start,
- irqres_b->start, irqres_err->start, irqres_p->start);
-
- /* add our adapter to the i2c stack */
- ret = i2c_add_numbered_adapter(adap);
- if (ret) {
- dev_err(&pdev->dev, "can't register I2C adapter\n");
- goto err_free_p_irq;
- }
-
- platform_set_drvdata(pdev, priv);
- i2c_set_adapdata(adap, priv);
-
- /* print module version information */
- dev_dbg(&pdev->dev, "module id=%u revision=%u\n",
- (i2c_r32(id) & I2C_ID_ID_MASK) >> I2C_ID_ID_OFFSET,
- (i2c_r32(id) & I2C_ID_REV_MASK) >> I2C_ID_REV_OFFSET);
-
- /* initialize HW */
- ret = falcon_i2c_hw_init(adap);
- if (ret) {
- dev_err(&pdev->dev, "can't configure adapter\n");
- goto err_remove_adapter;
- }
-
- dev_info(&pdev->dev, "version %s\n", DRV_VERSION);
-
- return 0;
-
-err_remove_adapter:
- i2c_del_adapter(adap);
- platform_set_drvdata(pdev, NULL);
-
-err_free_p_irq:
- free_irq(priv->irq_p, priv);
-
-err_free_err_irq:
- free_irq(priv->irq_err, priv);
-
-err_free_b_irq:
- free_irq(priv->irq_b, priv);
-
-err_free_lb_irq:
- free_irq(priv->irq_lb, priv);
-
-err_unmap_mem:
- iounmap(priv->membase);
-
-err_release_region:
- release_mem_region(mmres->start, resource_size(mmres));
-
-err_free_gpio:
- gpio_free(108);
- gpio_free(107);
-
-err_free_priv:
- kfree(priv);
-
- return ret;
-}
-
-static int __devexit falcon_i2c_remove(struct platform_device *pdev)
-{
- struct falcon_i2c *priv = platform_get_drvdata(pdev);
- struct resource *mmres;
-
- /* disable bus */
- i2c_w32_mask(I2C_RUN_CTRL_RUN_EN, 0, run_ctrl);
-
- /* remove driver */
- platform_set_drvdata(pdev, NULL);
- i2c_del_adapter(&priv->adap);
-
- free_irq(priv->irq_lb, priv);
- free_irq(priv->irq_b, priv);
- free_irq(priv->irq_err, priv);
- free_irq(priv->irq_p, priv);
-
- iounmap(priv->membase);
-
- gpio_free(108);
- gpio_free(107);
-
- kfree(priv);
-
- mmres = platform_get_resource(pdev, IORESOURCE_MEM, 0);
- release_mem_region(mmres->start, resource_size(mmres));
-
- dev_dbg(&pdev->dev, "removed\n");
-
- return 0;
-}
-
-static struct platform_driver falcon_i2c_driver = {
- .probe = falcon_i2c_probe,
- .remove = __devexit_p(falcon_i2c_remove),
- .driver = {
- .name = DRV_NAME,
- .owner = THIS_MODULE,
- },
-};
-
-static int __init falcon_i2c_init(void)
-{
- int ret;
-
- ret = platform_driver_register(&falcon_i2c_driver);
-
- if (ret)
- pr_debug(DRV_NAME ": can't register platform driver\n");
-
- return ret;
-}
-
-static void __exit falcon_i2c_exit(void)
-{
- platform_driver_unregister(&falcon_i2c_driver);
-}
-
-module_init(falcon_i2c_init);
-module_exit(falcon_i2c_exit);
-
-MODULE_DESCRIPTION("Lantiq FALC(tm) ON - I2C bus adapter");
-MODULE_ALIAS("platform:" DRV_NAME);
-MODULE_LICENSE("GPL");
-MODULE_VERSION(DRV_VERSION);
--
cgit v1.2.3