From 343c185b7d7383b1f5b5144e837045af28afc42b Mon Sep 17 00:00:00 2001 From: kaloz Date: Tue, 23 Jun 2009 21:04:37 +0000 Subject: use broken-out patches for the coldfire to make it easier to follow differences against the bsp git-svn-id: svn://svn.openwrt.org/openwrt/trunk@16547 3c298f89-4303-0410-b956-a3cf2f4a3e73 --- target/linux/coldfire/patches/071-m5445x_i2c.patch | 699 +++++++++++++++++++++ 1 file changed, 699 insertions(+) create mode 100644 target/linux/coldfire/patches/071-m5445x_i2c.patch (limited to 'target/linux/coldfire/patches/071-m5445x_i2c.patch') diff --git a/target/linux/coldfire/patches/071-m5445x_i2c.patch b/target/linux/coldfire/patches/071-m5445x_i2c.patch new file mode 100644 index 000000000..ecda4d6c7 --- /dev/null +++ b/target/linux/coldfire/patches/071-m5445x_i2c.patch @@ -0,0 +1,699 @@ +From e1618e943f60a4f8f778c4f7c389e2fa13eb0a83 Mon Sep 17 00:00:00 2001 +From: Kurt Mahan +Date: Thu, 26 Jun 2008 16:29:56 -0600 +Subject: [PATCH] Add I2C support for the M5445x platforms. + +LTIBName: m5445x-i2c +Signed-off-by: Kurt Mahan +--- + drivers/i2c/busses/Kconfig | 10 + + drivers/i2c/busses/Makefile | 1 + + drivers/i2c/busses/i2c-mcf.c | 573 ++++++++++++++++++++++++++++++++++++++++++ + drivers/i2c/busses/i2c-mcf.h | 75 ++++++ + 4 files changed, 659 insertions(+), 0 deletions(-) + create mode 100644 drivers/i2c/busses/i2c-mcf.c + create mode 100644 drivers/i2c/busses/i2c-mcf.h + +--- a/drivers/i2c/busses/Kconfig ++++ b/drivers/i2c/busses/Kconfig +@@ -302,6 +302,16 @@ config I2C_POWERMAC + This support is also available as a module. If so, the module + will be called i2c-powermac. + ++config I2C_MCF ++ tristate "MCF ColdFire" ++ depends on I2C && EXPERIMENTAL ++ help ++ If you say yes to this option, support will be included for the ++ I2C on most ColdFire CPUs ++ ++ This driver can also be built as a module. If so, the module ++ will be called i2c-mcf. ++ + config I2C_MPC + tristate "MPC107/824x/85xx/52xx/86xx" + depends on PPC32 +--- a/drivers/i2c/busses/Makefile ++++ b/drivers/i2c/busses/Makefile +@@ -53,6 +53,7 @@ obj-$(CONFIG_I2C_VOODOO3) += i2c-voodoo3 + obj-$(CONFIG_SCx200_ACB) += scx200_acb.o + obj-$(CONFIG_SCx200_I2C) += scx200_i2c.o + obj-$(CONFIG_I2C_MCF548x) += i2c-mcf548x.o ++obj-$(CONFIG_I2C_MCF) += i2c-mcf.o + + ifeq ($(CONFIG_I2C_DEBUG_BUS),y) + EXTRA_CFLAGS += -DDEBUG +--- /dev/null ++++ b/drivers/i2c/busses/i2c-mcf.c +@@ -0,0 +1,573 @@ ++/* ++ i2c-mcf.c - Part of lm_sensors, Linux kernel modules for hardware monitoring ++ ++ Copyright (c) 2005, Derek CL Cheung ++ ++ ++ Copyright (c) 2006-2007, emlix ++ Sebastian Hess ++ ++ Copyright (c) 2006-2007 Freescale Semiconductor, Inc ++ Yaroslav Vinogradov ++ Matt Waddel ++ ++ This program is free software; you can redistribute it and/or modify ++ it under the terms of the GNU General Public License as published by ++ the Free Software Foundation; either version 2 of the License, or ++ (at your option) any later version. ++ ++ This program is distributed in the hope that it will be useful, ++ but WITHOUT ANY WARRANTY; without even the implied warranty of ++ MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the ++ GNU General Public License for more details. ++ ++ You should have received a copy of the GNU General Public License ++ along with this program; if not, write to the Free Software ++ Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. ++ ++ Changes: ++ v0.1 26 March 2005 ++ Initial Release - developed on uClinux with 2.6.9 kernel ++ ++ v0.2 29 May 2006 ++ Modified to be more generic and added support for ++ i2c_master_xfer ++ ++ This I2C adaptor supports the ColdFire CPU I2C module. Since most Coldfire ++ CPUs' I2C module use the same register set (e.g., MCF5249), the code is very ++ portable and re-usable to other Coldfire CPUs. ++ ++ The transmission frequency is set at about 100KHz for the CPU board with ++ 8MHz crystal. If the CPU board uses different system clock frequency, you ++ should change the following line: ++ static int __init i2c_coldfire_init(void) ++ { ++ ......... ++ // Set transmission frequency 0x15 = ~100kHz ++ *MCF_I2C_I2FDR = 0x15; ++ ........ ++ } ++ ++ Remember to perform a dummy read to set the ColdFire CPU's I2C module for ++ read before reading the actual byte from a device ++ ++ The I2C_SM_BUS_BLOCK_DATA function are not yet ready but most lm_senors ++ do not care ++*/ ++ ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include "i2c-mcf.h" ++ ++ ++static struct i2c_algorithm coldfire_algorithm = { ++ /*.name = "ColdFire I2C algorithm", ++ .id = I2C_ALGO_SMBUS,*/ ++ .smbus_xfer = coldfire_i2c_access, ++ .master_xfer = coldfire_i2c_master, ++ .functionality = coldfire_func, ++}; ++ ++ ++static struct i2c_adapter coldfire_adapter = { ++ .owner = THIS_MODULE, ++ .class = I2C_CLASS_HWMON, ++ .algo = &coldfire_algorithm, ++ .name = "ColdFire I2C adapter", ++}; ++ ++ ++__u16 lastaddr; ++__u16 lastop; ++ ++static inline int coldfire_do_first_start(__u16 addr,__u16 flags) ++{ ++ int err; ++ /* ++ * Generate a stop and put the I2C module into slave mode ++ */ ++ *MCF_I2C_I2CR &= ~MCF_I2C_I2CR_MSTA; ++ ++ /* ++ * Generate a new Start signal ++ */ ++ err = coldfire_i2c_start(flags & I2C_M_RD ? I2C_SMBUS_READ : I2C_SMBUS_WRITE, ++ addr, FIRST_START); ++ if(err) return err; ++ ++ lastaddr = addr; ++ lastop = flags & I2C_M_RD; /* Ensure everything for new start */ ++ return 0; ++} ++ ++ ++/* ++ * read one byte data from the I2C bus ++ */ ++static int coldfire_read_data(u8 * const rxData, const enum I2C_ACK_TYPE ackType) { ++ ++ int timeout; ++ ++ *MCF_I2C_I2CR &= ~MCF_I2C_I2CR_MTX; /* master receive mode*/ ++ ++ if (ackType == NACK) ++ *MCF_I2C_I2CR |= MCF_I2C_I2CR_TXAK; /* generate NA */ ++ else ++ *MCF_I2C_I2CR &= ~MCF_I2C_I2CR_TXAK; /* generate ACK */ ++ ++ ++ /* read data from the I2C bus */ ++ *rxData = *MCF_I2C_I2DR; ++ ++ /* printk(">>> %s I2DR data is %.2x \n", __FUNCTION__, *rxData); */ ++ ++ /* wait for data transfer to complete */ ++ timeout = 500; ++ while (timeout-- && !(*MCF_I2C_I2SR & MCF_I2C_I2SR_IIF)) ++ udelay(1); ++ if (timeout <= 0) ++ printk("%s - I2C IIF never set. Timeout is %d \n", __FUNCTION__, ++ timeout); ++ ++ ++ /* reset the interrupt bit */ ++ *MCF_I2C_I2SR &= ~MCF_I2C_I2SR_IIF; ++ ++ if (timeout <= 0 ) ++ return -1; ++ else ++ return 0; ++ ++}; ++ ++ ++/* ++ * write one byte data onto the I2C bus ++ */ ++static int coldfire_write_data(const u8 txData) { ++ ++ int timeout; ++ ++ timeout = 500; ++ ++ *MCF_I2C_I2CR |= MCF_I2C_I2CR_MTX; /* I2C module into TX mode */ ++ *MCF_I2C_I2DR = txData; /* send the data */ ++ ++ /* wait for data transfer to complete */ ++ /* rely on the interrupt handling bit */ ++ timeout = 500; ++ while (timeout-- && !(*MCF_I2C_I2SR & MCF_I2C_I2SR_IIF)) ++ udelay(1); ++ if (timeout <=0) ++ printk("%s - I2C IIF never set. Timeout is %d \n", __FUNCTION__, ++ timeout); ++ ++ ++ /* reset the interrupt bit */ ++ *MCF_I2C_I2SR &= ~MCF_I2C_I2SR_IIF; ++ ++ if (timeout <= 0 ) ++ return -1; ++ else ++ return 0; ++ ++}; ++ ++ ++ ++ ++/* ++ * Generate I2C start or repeat start signal ++ * Combine the 7 bit target_address and the R/W bit and put it onto the I2C bus ++ */ ++static int coldfire_i2c_start(const char read_write, const u16 target_address, const enum I2C_START_TYPE start_type) { ++ ++ int timeout; ++ ++ /* printk(">>> %s START TYPE %s \n", __FUNCTION__, ++ start_type == FIRST_START ? "FIRST_START":"REPEAT_START");*/ ++ ++ *MCF_I2C_I2CR |= MCF_I2C_I2CR_IEN; ++ ++ if (start_type == FIRST_START) { ++ /* Make sure the I2C bus is idle */ ++ timeout = 500; /* 500us timeout */ ++ while (timeout-- && (*MCF_I2C_I2SR & MCF_I2C_I2SR_IBB)) ++ udelay(1); ++ if (timeout <= 0) { ++ printk("%s - I2C bus always busy in the past 500us timeout is %d \n", __FUNCTION__, timeout); ++ goto check_rc; ++ } ++ /* generate a START and put the I2C module into MASTER TX mode*/ ++ *MCF_I2C_I2CR |= (MCF_I2C_I2CR_MSTA | MCF_I2C_I2CR_MTX); ++ ++ /* wait for bus busy to be set */ ++ timeout = 500; ++ while (timeout-- && !(*MCF_I2C_I2SR & MCF_I2C_I2SR_IBB)) ++ udelay(1); ++ if (timeout <= 0) { ++ printk("%s - I2C bus is never busy after START. Timeout is %d \n", __FUNCTION__, timeout); ++ goto check_rc; ++ } ++ ++ } else { ++ /* this is repeat START */ ++ udelay(500); /* need some delay before repeat start */ ++ *MCF_I2C_I2CR |= (MCF_I2C_I2CR_MSTA | MCF_I2C_I2CR_RSTA); ++ } ++ ++ ++ /* combine the R/W bit and the 7 bit target address and put it onto ++ the I2C bus */ ++ *MCF_I2C_I2DR = ((target_address & 0x7F) << 1) | (read_write == I2C_SMBUS_WRITE ? 0x00 : 0x01); ++ ++ /* wait for bus transfer to complete */ ++ /* when one byte transfer is completed, IIF set at the faling edge of ++ the 9th clock */ ++ timeout = 500; ++ while (timeout-- && !(*MCF_I2C_I2SR & MCF_I2C_I2SR_IIF)) ++ udelay(1); ++ if (timeout <= 0) ++ printk("%s - I2C IIF never set. Timeout is %d \n", __FUNCTION__, timeout); ++ ++ ++check_rc: ++ /* reset the interrupt bit */ ++ *MCF_I2C_I2SR &= ~MCF_I2C_I2SR_IIF; ++ ++ if (timeout <= 0) ++ return -1; ++ else ++ return 0; ++}; ++ ++ ++/* ++ * 5282 SMBUS supporting functions ++ */ ++ ++static s32 coldfire_i2c_access(struct i2c_adapter *adap, u16 addr, ++ unsigned short flags, char read_write, ++ u8 command, int size, union i2c_smbus_data *data) ++{ ++ int rc = 0; ++ u8 rxData, tempRxData[2]; ++ ++ switch (size) { ++ case I2C_SMBUS_QUICK: ++ rc = coldfire_i2c_start(read_write, addr, FIRST_START); /* generate START */ ++ break; ++ case I2C_SMBUS_BYTE: ++ rc = coldfire_i2c_start(read_write, addr, FIRST_START); ++ *MCF_I2C_I2CR |= MCF_I2C_I2CR_TXAK; /*generate NA */ ++ if (read_write == I2C_SMBUS_WRITE) ++ rc += coldfire_write_data(command); ++ else { ++ coldfire_read_data(&rxData, NACK);/*dummy read*/ ++ rc += coldfire_read_data(&rxData, NACK); ++ data->byte = rxData; ++ } ++ *MCF_I2C_I2CR &= ~MCF_I2C_I2CR_TXAK; /* reset ACK bit */ ++ break; ++ case I2C_SMBUS_BYTE_DATA: ++ rc = coldfire_i2c_start(I2C_SMBUS_WRITE, addr, FIRST_START); ++ rc += coldfire_write_data(command); ++ if (read_write == I2C_SMBUS_WRITE) ++ rc += coldfire_write_data(data->byte); ++ else { ++ /* This is SMBus READ Byte Data Request. ++ Perform REPEAT START */ ++ rc += coldfire_i2c_start(I2C_SMBUS_READ, addr, ++ REPEAT_START); ++ coldfire_read_data(&rxData, ACK);/* dummy read*/ ++ /* Disable Acknowledge, generate STOP after ++ next byte transfer */ ++ rc += coldfire_read_data(&rxData, NACK); ++ data->byte = rxData; ++ } ++ *MCF_I2C_I2CR &= ~MCF_I2C_I2CR_TXAK;/* reset to normal ACk */ ++ break; ++ case I2C_SMBUS_PROC_CALL: ++ case I2C_SMBUS_WORD_DATA: ++ dev_info(&adap->dev, "size = I2C_SMBUS_WORD_DATA \n"); ++ rc = coldfire_i2c_start(I2C_SMBUS_WRITE, addr, ++ FIRST_START); ++ rc += coldfire_write_data(command); ++ if (read_write == I2C_SMBUS_WRITE) { ++ rc += coldfire_write_data(data->word & 0x00FF); ++ rc += coldfire_write_data((data->word & 0x00FF) >> 8); ++ } else { ++ /* This is SMBUS READ WORD request. ++ Peform REPEAT START */ ++ rc += coldfire_i2c_start(I2C_SMBUS_READ, addr, ++ REPEAT_START); ++ coldfire_read_data(&rxData, ACK);/* dummy read*/ ++ /* Disable Acknowledge, generate STOP after ++ next byte transfer */ ++ /* read the MS byte from the device */ ++ rc += coldfire_read_data(&rxData, NACK); ++ tempRxData[1] = rxData; ++ /* read the LS byte from the device */ ++ rc += coldfire_read_data(&rxData, NACK); ++ tempRxData[0] = rxData; ++ /* the host driver expect little endian ++ convention. Swap the byte */ ++ data->word = (tempRxData[0] << 8)|tempRxData[1]; ++ } ++ *MCF_I2C_I2CR &= ~MCF_I2C_I2CR_TXAK; ++ break; ++ case I2C_SMBUS_BLOCK_DATA: ++ /* Not done yet */ ++ break; ++ default: ++ printk("Unsupported I2C size \n"); ++ rc = -1; ++ break; ++ }; ++ ++ /* Generate a STOP and put I2C module into slave mode */ ++ *MCF_I2C_I2CR &= ~MCF_I2C_I2CR_MSTA; ++ ++ /* restore interrupt */ ++ *MCF_I2C_I2CR |= MCF_I2C_I2CR_IIEN; ++ ++ if (rc < 0) ++ return -1; ++ else ++ return 0; ++}; ++ ++ ++/* ++ * List the SMBUS functions supported by this I2C adaptor ++ * Also tell the I2C Subsystem that we are able of master_xfer() ++ */ ++static u32 coldfire_func(struct i2c_adapter *adapter) ++{ ++ return(I2C_FUNC_SMBUS_QUICK | ++ I2C_FUNC_SMBUS_BYTE | ++ I2C_FUNC_SMBUS_PROC_CALL | ++ I2C_FUNC_SMBUS_BYTE_DATA | ++ I2C_FUNC_SMBUS_WORD_DATA | ++ I2C_FUNC_I2C | ++ I2C_FUNC_SMBUS_BLOCK_DATA); ++}; ++ ++static int coldfire_i2c_master(struct i2c_adapter *adap,struct i2c_msg *msgs, ++ int num) ++{ ++ u8 dummyRead; ++ struct i2c_msg *p; ++ int i, err = 0; ++ int ic=0; ++ ++ lastaddr = 0; ++ lastop = 8; ++ ++ /* disable the IRQ, we are doing polling */ ++ *MCF_I2C_I2CR &= ~MCF_I2C_I2CR_IIEN; ++ ++ dev_dbg(&adap->dev,"Num of actions: %d\n", num); ++ ++ for (i = 0; !err && i < num; i++) { ++ p = &msgs[i]; ++ ++ ++ if (!p->len) ++ { ++ dev_dbg(&adap->dev,"p->len == 0!\n"); ++ continue; ++ } ++ /* ++ * Generate a new Start, if the target address differs from ++ * the last target, generate a stop in this case first ++ */ ++ if(p->addr != lastaddr) ++ { ++ err = coldfire_do_first_start(p->addr,p->flags); ++ if(err) ++ { ++ dev_dbg(&adap->dev,"First Init failed!\n"); ++ break; ++ } ++ } ++ ++ else if((p->flags & I2C_M_RD) != lastop) ++ { ++ /* ++ * If the Operational Mode changed, we need to do this ++ * here ... ++ */ ++ dev_dbg(&adap->dev,"%s(): Direction changed, was: %d; is now: %d\n", __FUNCTION__, lastop, p->flags & I2C_M_RD); ++ ++ /* Last op was an read, now it's write: complete stop ++ and reinit */ ++ if (lastop & I2C_M_RD) ++ { ++ dev_dbg(&adap->dev,"%s(): The device is in read state, we must reset!\n", __FUNCTION__); ++ if((err = coldfire_do_first_start(p->addr,p->flags))) ++ break; ++ } ++ else ++ { ++ dev_dbg(&adap->dev,"%s(): We switchted to read mode\n",__FUNCTION__); ++ if((err = coldfire_i2c_start((p->flags & I2C_M_RD) ? I2C_SMBUS_READ : I2C_SMBUS_WRITE, ++ p->addr, REPEAT_START))) ++ break; ++ } ++ ++ lastop = p->flags & I2C_M_RD; /* Save the last op */ ++ } ++ ++ if (p->flags & I2C_M_RD) ++ { ++ /* ++ * When ever we get here, a new session was activated, ++ * so read a dummy byte ++ */ ++ coldfire_read_data(&dummyRead, ACK); ++ /* ++ * read p->len -1 bytes with ACK to the slave, ++ * read the last byte without the ACK, to inform him ++ * about the stop afterwards ++ */ ++ ic = 0; ++ while(!err && (ic < p->len-1 )) ++ { ++ err = coldfire_read_data(p->buf+ic, ACK ); ++ ic++; ++ } ++ if(!err) ++ err = coldfire_read_data(p->buf+ic, NACK); ++ dev_dbg(&coldfire_adapter.dev,"read: %2x\n",p->buf[ic]); ++ } ++ else ++ { ++ if(p->len == 2) ++ dev_dbg(&coldfire_adapter.dev,"writing: 0x %2x %2x\n", p->buf[0], p->buf[1]); ++ ++ /* ++ * Write data to the slave ++ */ ++ for(ic=0; !err && ic < p->len; ic++) ++ { ++ err = coldfire_write_data(p->buf[ic]); ++ if(err) ++ { ++ dev_dbg(&coldfire_adapter.dev, "Failed to write data\n"); ++ } ++ } ++ } ++ } ++ ++ /* ++ * Put the device into slave mode to enable the STOP Generation ++ * (the RTC needs this) ++ */ ++ *MCF_I2C_I2CR &= ~MCF_I2C_I2CR_MSTA; ++ ++ *MCF_I2C_I2CR &= ~MCF_I2C_I2CR_TXAK; /* reset the ACK bit */ ++ ++ /* restore interrupt */ ++ *MCF_I2C_I2CR |= MCF_I2C_I2CR_IIEN; ++ ++ /* Return the number of messages processed, or the error code. */ ++ if (err == 0) ++ err = num; ++ return err; ++} ++ ++ ++/* ++ * Initalize the 5282 I2C module ++ * Disable the 5282 I2C interrupt capability. Just use callback ++ */ ++ ++static int __init i2c_coldfire_init(void) ++{ ++ int retval; ++ u8 dummyRead; ++ ++#if defined(CONFIG_M532x) || defined(CONFIG_M5445X) ++ /* ++ * Initialize the GPIOs for I2C ++ */ ++ MCF_GPIO_PAR_FECI2C |= (0 ++ | MCF_GPIO_PAR_FECI2C_PAR_SDA(3) ++ | MCF_GPIO_PAR_FECI2C_PAR_SCL(3)); ++#elif defined(CONFIG_M5253) ++ { ++ volatile u32 *reg; ++ /* GPIO Bit 41 = SCL0, Bit 42 = SDA0 */ ++ reg = (volatile u32 *)(MCF_MBAR2 + MCFSIM2_GPIO1FUNC); ++ *reg &= 0xFFFFF9FF; ++ } ++#else ++ /* Initialize PASP0 and PASP1 to I2C functions, 5282 user guide 26-19 */ ++ /* Port AS Pin Assignment Register (PASPAR) */ ++ /* PASPA1 = 11 = AS1 pin is I2C SDA */ ++ /* PASPA0 = 11 = AS0 pin is I2C SCL */ ++ *MCF_GPIO_PASPAR |= 0x000F; /* u16 declaration */ ++#endif ++ ++ ++ /* Set transmission frequency 0x15 = ~100kHz */ ++ *MCF_I2C_I2FDR = 0x15; ++ ++ /* set the 5282 I2C slave address though we never use it */ ++ *MCF_I2C_I2ADR = 0x6A; ++ ++ /* Enable I2C module and if IBB is set, do the special initialzation */ ++ /* procedures as are documented at the 5282 User Guide page 24-11 */ ++ *MCF_I2C_I2CR |= MCF_I2C_I2CR_IEN; ++ if ((*MCF_I2C_I2SR & MCF_I2C_I2SR_IBB) == 1) { ++ printk("%s - do special 5282 I2C init procedures \n", ++ __FUNCTION__); ++ *MCF_I2C_I2CR = 0x00; ++ *MCF_I2C_I2CR = 0xA0; ++ dummyRead = *MCF_I2C_I2DR; ++ *MCF_I2C_I2SR = 0x00; ++ *MCF_I2C_I2CR = 0x00; ++ } ++ ++ /* default I2C mode is - slave and receive */ ++ *MCF_I2C_I2CR &= ~(MCF_I2C_I2CR_MSTA | MCF_I2C_I2CR_MTX); ++ ++ coldfire_adapter.dev.parent = &platform_bus; ++ retval = i2c_add_adapter(&coldfire_adapter); ++ ++ if (retval < 0) ++ printk("%s - return code is: %d \n", __FUNCTION__, retval); ++ ++ return retval; ++}; ++ ++ ++/* ++ * I2C module exit function ++ */ ++ ++static void __exit i2c_coldfire_exit(void) ++{ ++ /* disable I2C and Interrupt */ ++ *MCF_I2C_I2CR &= ~(MCF_I2C_I2CR_IEN | MCF_I2C_I2CR_IIEN); ++ i2c_del_adapter(&coldfire_adapter); ++ ++}; ++ ++ ++MODULE_AUTHOR("Derek CL Cheung "); ++MODULE_DESCRIPTION("MCF5282 I2C adaptor"); ++MODULE_LICENSE("GPL"); ++ ++module_init(i2c_coldfire_init); ++module_exit(i2c_coldfire_exit); +--- /dev/null ++++ b/drivers/i2c/busses/i2c-mcf.h +@@ -0,0 +1,75 @@ ++/* ++ i2c-mcf.h - header file for i2c-mcf.c ++ ++ Copyright (c) 2005, Derek CL Cheung ++ ++ ++ Copyright (c) 2006-2007, emlix ++ Sebastian Hess ++ ++ Copyright (c) 2006-2007 Freescale Semiconductor, Inc ++ Yaroslav Vinogradov ++ Matt Waddel ++ ++ This program is free software; you can redistribute it and/or modify ++ it under the terms of the GNU General Public License as published by ++ the Free Software Foundation; either version 2 of the License, or ++ (at your option) any later version. ++ ++ This program is distributed in the hope that it will be useful, ++ but WITHOUT ANY WARRANTY; without even the implied warranty of ++ MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the ++ GNU General Public License for more details. ++ ++ You should have received a copy of the GNU General Public License ++ along with this program; if not, write to the Free Software ++ Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. ++ ++ Changes: ++ v0.1 26 March 2005 ++ Initial Release - developed on uClinux with 2.6.9 kernel ++ v0.2 29 May 2006 ++ Modified to be more generic and added support for ++ i2c_master_xfer ++*/ ++ ++ ++#ifndef __I2C_MCF_H__ ++#define __I2C_MCF_H__ ++ ++enum I2C_START_TYPE { FIRST_START, REPEAT_START }; ++enum I2C_ACK_TYPE { ACK, NACK}; ++ ++/* Function prototypes */ ++static u32 coldfire_func(struct i2c_adapter *adapter); ++static s32 coldfire_i2c_access(struct i2c_adapter *adap, u16 address, ++ unsigned short flags, char read_write, ++ u8 command, int size, union i2c_smbus_data *data); ++static int coldfire_write_data(const u8 data); ++static int coldfire_i2c_start(const char read_write, const u16 target_address, const enum I2C_START_TYPE i2c_start); ++static int coldfire_read_data(u8 * const rxData, const enum I2C_ACK_TYPE ackType); ++static int coldfire_i2c_master(struct i2c_adapter *adap,struct i2c_msg *msgs, int num); ++void dumpReg(char *, u16 addr, u8 data); ++ ++#define MCF_I2C_I2ADR_ADDR(x) (((x)&0x7F)<<0x01) ++#define MCF_I2C_I2FDR_IC(x) (((x)&0x3F)) ++ ++/* I2C Control Register */ ++#define MCF_I2C_I2CR_IEN (0x80) /* I2C enable */ ++#define MCF_I2C_I2CR_IIEN (0x40) /* interrupt enable */ ++#define MCF_I2C_I2CR_MSTA (0x20) /* master/slave mode */ ++#define MCF_I2C_I2CR_MTX (0x10) /* transmit/receive mode */ ++#define MCF_I2C_I2CR_TXAK (0x08) /* transmit acknowledge enable */ ++#define MCF_I2C_I2CR_RSTA (0x04) /* repeat start */ ++ ++/* I2C Status Register */ ++#define MCF_I2C_I2SR_ICF (0x80) /* data transfer bit */ ++#define MCF_I2C_I2SR_IAAS (0x40) /* I2C addressed as a slave */ ++#define MCF_I2C_I2SR_IBB (0x20) /* I2C bus busy */ ++#define MCF_I2C_I2SR_IAL (0x10) /* aribitration lost */ ++#define MCF_I2C_I2SR_SRW (0x04) /* slave read/write */ ++#define MCF_I2C_I2SR_IIF (0x02) /* I2C interrupt */ ++#define MCF_I2C_I2SR_RXAK (0x01) /* received acknowledge */ ++ ++/********************************************************************/ ++#endif /* __I2C_MCF_H__ */ -- cgit v1.2.3