From e3a81c46a5b399e5579144aec5222d3c82055a63 Mon Sep 17 00:00:00 2001 From: hauke Date: Thu, 3 Jan 2013 01:58:01 +0000 Subject: switch: ROBO Switch Gigabit MII Support I wrote this patch some time ago because I had a need for one of the Gigabit ports (Linksys E3000) to be forced to 100FD. This is based on the robocfg sources included w/ the RT-N16 sources from ASUS. Since work is progressing on a BGMAC driver that could be included in OpenWRT, this may be useful to someone else. In testing, forcing the speed to 10/100 or 1000 worked fine; however, when trying to force full-duplex mode, the result was always half-duplex. I was not able to isolate the source of the problem (this patch, driver or H/W limitation). The only way I could get it to work was to set the port to Auto, but then only advertise 100FD (not included in this patch). I have a modified version of the robocfg package as well, I'd have to clean it up a little first (remove the full-duplex hack) before submitting it if there is interest. Signed-off-by: Nathan Hintz git-svn-id: svn://svn.openwrt.org/openwrt/trunk@34992 3c298f89-4303-0410-b956-a3cf2f4a3e73 --- package/switch/src/etc53xx.h | 45 ++++++++++++++++++++++++-------------------- 1 file changed, 25 insertions(+), 20 deletions(-) (limited to 'package/switch/src/etc53xx.h') diff --git a/package/switch/src/etc53xx.h b/package/switch/src/etc53xx.h index d5b1310cb..c21d1bc79 100644 --- a/package/switch/src/etc53xx.h +++ b/package/switch/src/etc53xx.h @@ -15,9 +15,10 @@ #define __BCM535M_H_ /* ROBO embedded device type */ -#define ROBO_DEV_5380 1 -#define ROBO_DEV_5365 2 -#define ROBO_DEV_5350 3 +#define ROBO_DEV_5380 1 +#define ROBO_DEV_5365 2 +#define ROBO_DEV_5350 3 +#define ROBO_DEV_53115 4 /* BCM5325m GLOBAL PAGE REGISTER MAP */ #ifndef _CFE_ @@ -316,6 +317,18 @@ typedef struct _ROBO_ARL_SEARCH_RESULT_MCAST_STRUC #define ROBO_ARL_SEARCH_RESULT_EXT 0x2c /* ARL Search Result Extension (5350): 8bit */ #define ROBO_ARL_VID_ENTRY0 0x30 /* ARL VID Entry 0: 64bit */ #define ROBO_ARL_VID_ENTRY1 0x32 /* ARL VID Entry 1: 64bit */ +#define ROBO_ARL_SEARCH_CTRL_53115 0x50 /* ARL Search Control: 8bit */ +#define ROBO_ARL_SEARCH_ADDR_53115 0x51 /* ARL Search Address: 16bit */ +#define ROBO_ARL_SEARCH_RESULT_53115 0x60 /* ARL Search Result: 64bit */ +#define ROBO_ARL_SEARCH_RESULT_EXT_53115 0x68 /* ARL Search Result Extension (53115): 16bit */ + +/* BCM5395/5397/5398/53115 */ +#define ROBO_VTBL_ACCESS 0x60 /* VLAN table access: 8bit */ +#define ROBO_VTBL_INDX 0x61 /* VLAN table address index: 16bit */ +#define ROBO_VTBL_ENTRY 0x63 /* VLAN table entry: 32bit */ +#define ROBO_VTBL_ACCESS_5395 0x80 /* VLAN table access: 8bit */ +#define ROBO_VTBL_INDX_5395 0x81 /* VLAN table address index: 16bit */ +#define ROBO_VTBL_ENTRY_5395 0x83 /* VLAN table entry: 32bit */ /* BCM5325m MANAGEMENT FRAME REGISTERS (0x6) REGISTER MAP: 8/16 bit regs */ #define ROBO_MGMT_FRAME_RD_DATA 0x00 /* Management Frame Read Data :8bit*/ @@ -342,6 +355,8 @@ typedef struct _ROBO_ARL_SEARCH_RESULT_MCAST_STRUC #define NUM_VLAN_TABLE_ENTRIES_5350 16 /* number of entries in VLAN table */ #define ARL_TABLE_ADDR_5350 0x1c00 /* offset of ARL table start (5350) */ #endif +#define NUM_ARL_TABLE_ENTRIES_53115 4096 /* number of entries in ARL table (53115) */ +#define NUM_VLAN_TABLE_ENTRIES_53115 4096 /* number of entries in VLAN table */ typedef struct _ROBO_MEM_ACCESS_CTRL_STRUC { unsigned int memAddr:14; /* 64-bit memory address */ @@ -529,6 +544,7 @@ typedef struct _ROBO_VLAN_CTRL0_STRUC #define VLAN_ID_HIGH_BITS 0 /* static high bits in table access reg */ #define VLAN_ID_MAX 255 /* max VLAN id */ #define VLAN_ID_MAX5350 15 /* max VLAN id (5350) */ +#define VLAN_ID_MAX5395 4094 /* max VLAN id (5395) */ #define VLAN_ID_MASK VLAN_ID_MAX /* VLAN id mask */ #ifdef BCM5380 #define VLAN_UNTAG_SHIFT 13 /* for postioning untag bits in write reg */ @@ -594,26 +610,15 @@ typedef struct _ROBO_VLAN_READ_WRITE_STRUC_5350 #define ROBO_VLAN_PORT5_DEF_TAG 0x1a /* 16b: VLAN Port 5 Default Tag Register */ #define ROBO_VLAN_PORT6_DEF_TAG 0x1c /* 16b: VLAN Port 6 Default Tag Register */ #define ROBO_VLAN_PORT7_DEF_TAG 0x1e /* 16b: VLAN Port 7 Default Tag Register */ - -/* obsolete */ -#define ROBO_VLAN_PORT0_CTRL 0x00 /* 16b: Port 0 VLAN Register */ -#define ROBO_VLAN_PORT1_CTRL 0x02 /* 16b: Port 1 VLAN Register */ -#define ROBO_VLAN_PORT2_CTRL 0x04 /* 16b: Port 2 VLAN Register */ -#define ROBO_VLAN_PORT3_CTRL 0x06 /* 16b: Port 3 VLAN Register */ -#define ROBO_VLAN_PORT4_CTRL 0x08 /* 16b: Port 4 VLAN Register */ -#define ROBO_VLAN_IM_PORT_CTRL 0x10 /* 16b: Inverse MII Port VLAN Reg */ -#define ROBO_VLAN_SMP_PORT_CTRL 0x12 /* 16b: Serial Port VLAN Register */ -#define ROBO_VLAN_PORTSPI_DEF_TAG 0x1c /* 16b: VLAN Port SPI Default Tag Register */ -#define ROBO_VLAN_PRIORITY_REMAP 0x20 /* 24b: VLAN Priority Re-Map Register */ +#define ROBO_VLAN_PORT8_DEF_TAG 0x20 /* 16b: VLAN Port 8 Default Tag Register */ +/* 53115 only */ +#define ROBO_DUPLEX_STAT_SUMMARY_53115 0x08 /* Duplex Status Summary: 16bit */ +#define ROBO_JUMBO_PAGE 0x40 +#define ROBO_JUMBO_CTRL 0x01 /* 32bit */ +#define ROBO_JUMBO_SIZE 0x05 /* 16bit */ #ifndef _CFE_ #pragma pack() #endif - #endif /* !__BCM535M_H_ */ - - - - - -- cgit v1.2.3