From 128434cb236523f4cec881622b8606cb1533b677 Mon Sep 17 00:00:00 2001
From: nbd <nbd@3c298f89-4303-0410-b956-a3cf2f4a3e73>
Date: Sun, 15 Jun 2008 11:11:28 +0000
Subject: (6/6) bcm57xx: package

This is the bcm57xx package.  I have tested default vlan functions,
but I dont have the equipment to test more advanced setups.  The default
vlan setup seems to be working fine.  I also added the activate_gpio
parameter which will make the driver activate the switch via gpio before
probing for it.

I'm not sure which method is best for autoload.  For the wrt350n, I
need the activate_gpio parameter.  But its probably not a good idea
to add that to the autoload file.  On a system without a bcm57xx switch,
isn't it a bad idea to mess with the gpios looking for the switch? Ideally,
wouldn't it be best to load the bcm57xx module from broadcom-diag, after
it has determined which router its on?  I tried using 'request_module' from
there, but had no success.  For now, I am relying on preinit to load
the bcm57xx module with activate_gpio param, after it has failed to load
switch_robo and switch_adm.

Signed-off-by: Ben Pfountz <netprince (at) vt (dot) edu>


git-svn-id: svn://svn.openwrt.org/openwrt/trunk@11471 3c298f89-4303-0410-b956-a3cf2f4a3e73
---
 package/broadcom-57xx/src/proto/eap.h | 45 +++++++++++++++++++++++++++++++++++
 1 file changed, 45 insertions(+)
 create mode 100644 package/broadcom-57xx/src/proto/eap.h

(limited to 'package/broadcom-57xx/src/proto/eap.h')

diff --git a/package/broadcom-57xx/src/proto/eap.h b/package/broadcom-57xx/src/proto/eap.h
new file mode 100644
index 000000000..36ed13876
--- /dev/null
+++ b/package/broadcom-57xx/src/proto/eap.h
@@ -0,0 +1,45 @@
+/*
+ * Extensible Authentication Protocol (EAP) definitions
+ *
+ * See
+ * RFC 2284: PPP Extensible Authentication Protocol (EAP)
+ *
+ * Copyright (C) 2002 Broadcom Corporation
+ *
+ * $Id: eap.h,v 1.2 2007/04/17 08:52:47 yogo Exp $
+ */
+
+#ifndef _eap_h_														
+#define _eap_h_
+
+/* EAP packet format */
+typedef struct {
+	unsigned char code;	/* EAP code */
+	unsigned char id;	/* Current request ID */
+	unsigned short length;	/* Length including header */
+	unsigned char type;	/* EAP type (optional) */
+	unsigned char data[1];	/* Type data (optional) */
+} eap_header_t;
+
+#define EAP_HEADER_LEN 4
+
+/* EAP codes */
+#define EAP_REQUEST	1
+#define EAP_RESPONSE	2
+#define EAP_SUCCESS	3
+#define EAP_FAILURE	4
+
+/* EAP types */
+#define EAP_IDENTITY		1
+#define EAP_NOTIFICATION	2
+#define EAP_NAK			3
+#define EAP_MD5			4
+#define EAP_OTP			5
+#define EAP_GTC			6
+#define EAP_TLS			13
+#define EAP_EXPANDED		254
+#define BCM_EAP_SES		10
+#define BCM_EAP_EXP_LEN		12  /* EAP_LEN 5 + 3 bytes for SMI ID + 4 bytes for ven type */
+#define BCM_SMI_ID		0x113d
+
+#endif /* _eap_h_ */
-- 
cgit v1.2.3