| Commit message (Collapse) | Author | Age | Files | Lines |
... | |
|
|
|
|
|
|
|
|
|
|
| |
Bump to version 3.2.
Simplify and correct kernel config (based on x86/config-3.2).
Drop obsolete CS5535 GPIO driver.
[Patch from Philipp Prindeville, via http://patchwork.openwrt.org/patch/1804/]
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29981 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
| |
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29978 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
| |
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29976 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
| |
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29975 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
| |
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29974 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This patch adds support for D-LINK DIR-615 E4 board. It's mostly based
on the existing support for DIR-600 A1, with some changes in the leds
configuration.
It's an updated version of the patch that reliably works on my hw for
about a year (it was built from trunk on Jan 2011). When I decided to
update the firmware and checked for the current support for that device,
I also found previously posted patches by Alexey Loukianov that
mentioned some stability issues. I'm not sure where could be the
difference, the patches are very similar except the wmac led pin number
- I was using 1, and those patches used 17.
[juhosg: add 3.2 support]
Signed-off-by: Vadim Girlin <vadimgirlin@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29973 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Adds support for TL-MR11U, a portable router with very similar
hardware to the TL-WR703N and TL-MR3020, but with an onboard
2000mAh battery.
Tested, working:
All interfaces (Ethernet, 802.11n, USB)
WPS & Reset switches (Power appears to be a hardware slider)
Ethernet, Wifi, 3G LEDs (Power & charging LEDs hardware controlled)
Sysupgrade
[juhosg: fix indentations to use TABs instead of spaces, fix 3.2 patch
breakage]
Signed-off-by: Simon Taylor <simon.taylor.uk@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29972 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
| |
The lzma compressed kernel is used by one of the loaders.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29971 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
| |
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29970 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
| |
This change moves the WAN port into a separate VLAN.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29969 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
| |
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29967 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
| |
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29966 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
| |
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29965 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
| |
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29960 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
| |
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29959 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
| |
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29958 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
| |
Thanks KanjiMonster
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29955 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
| |
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29954 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
| |
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29953 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
| |
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29942 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
| |
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29941 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
| |
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29940 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
| |
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29939 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
|
| |
This reference board is equipped with:
- AR7242 SoC
- AR9580 on-board Wi-Fi
- AR8316 switch
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29935 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
| |
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29934 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
| |
These devices have two devices on the bus, the host controller itself and the device.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29923 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
| |
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29917 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
| |
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29916 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
| |
Thanks to Florian for reporting.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29915 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
|
| |
[juhosg: remove ath9k from the the profile package list, build WPE72
image with the Default profile as well]
Signed-off-by: Johnathan Boyce <jon.boyce@globalreach.eu.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29914 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
|
|
|
| |
This patch adds support for Compex WPE72 bare board and Compex WPE72NX
Indoor Access Point.
[juhosg: add support to 3.2 as well]
Signed-off-by: Johnathan Boyce <jon.boyce@globalreach.eu.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29912 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
| |
Signed-off-by: Johnathan Boyce <jon.boyce@globalreach.eu.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29911 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This patch adds support for the Sitecom WL-341 v3 and other Sercomm
IP1006RRv2 based boards for sysupgrade support and for the initial
flash through pushbutton initiated recovery mode with the special
partition table and fixes for the quirks and things required by the
modified bootloader.
There is a known bug, Wi-Fi is not working on my board probably
because of the lack of RAM (the board only has 16MiB ram -- half of
the normal amount for non rebadged versions, but there is an empty
slot for another ram chip,) but I don't know for sure. The driver
loads but hostapd fails to load so I think it's not related to the
specific device except for the lack of RAM.
Moreover, only 7 of the 11 onboard leds are confirmed working, it
seems that one of the others is always on and the remaining ones are
connected to the wireless card leds already recognized by OpenWrt
[juhosg: reordered some parts in order to keep things sorted
alphabetically]
Signed-off-by: Marco Antonio Mauro <marcus90@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29910 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
modify LED behaviour
This patch fixes the board detection of the TL-MR3020.
The LED behaviour has also been modified:
* The WPS LED is the diag LED now.
* A netdev trigger for the LAN LED has been added.
The profile of the TL-MR3020 has been updated because the needed package
"kmod-ledtrig-usbdev" was missing which resulted in a non-working usbdev
trigger for the 3G/USB LED.
[juhosg: the board name changes has been removed, and the kernel files
has been changed instead.]
Signed-off-by: Christian Cier-Zniewski <c.cier@gmx.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29905 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
|
|
| |
This patch fixes the GPIO polarity for the button and the sliding
switch. The buttons are not active low. "Pressed" and "Released"
events are wrong without the patch.
Signed-off-by: Christian Cier-Zniewski <c.cier@gmx.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29904 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
| |
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29900 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
| |
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29899 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
| |
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29897 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
| |
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29896 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
| |
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29895 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
| |
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29894 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
| |
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29893 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
| |
Signed-off-by: Daniel Golle <dgolle@allnet.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29884 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
| |
This adds uci-defaults and sysupgrade support for the ALL0256N.
Signed-off-by: Daniel Golle <dgolle@allnet.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29883 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
| |
Signed-off-by: Daniel Golle <dgolle@allnet.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29882 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
| |
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29880 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
| |
This reduces the size of the ImageBuilder tarball a lot.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29879 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
| |
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29878 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
In this patch:
* rename Argus leds to avoid underscores
* rename Belkin F5D8235 v1 leds from f5d8234 to f5d8235
* remove Belkin F5D8235 v1 status led defined as storage led (it was
defined as usb led earlier, just in wrong place) - it should have
router led as in v2
* add Argus, Sparklan and Belkin F5D8235 v2 status leds
* add Belkin F5D8235 v1 and v2 usb leds
* fix Belkin F5D8235 v2 network config generation and mac address axtraction
* fix Sparklan board identification
* add Sparklan usb led (this board doesn't have usb connector by
default and the led is hidden also but if you are going to solder
the connector then you'll see the led too)
* add Sparklan network config generation and mac address extraction
* fix empty string test in network script and...
* ...sort case entries by the first board in the list
Signed-off-by: Roman Yeryomin <roman@advem.lv>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29871 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
| |
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29870 3c298f89-4303-0410-b956-a3cf2f4a3e73
|