summaryrefslogtreecommitdiffstats
path: root/target/linux
Commit message (Expand)AuthorAgeFilesLines
* [mcs814x] nuport-mac: rework PHY interrupt configuration to avoid racesflorian2012-08-081-7/+7
* [mcs814x] nuport-mac: close possible race condition during startflorian2012-08-081-1/+5
* [mcs814x] nuport-mac: unmap the DMA buffer when closing deviceflorian2012-08-081-0/+4
* [mcs814x] nuport-mac: check dma_map_single address return valuesflorian2012-08-081-0/+4
* [mcs814x] build a Devolo dLAN USB Extender specific imageflorian2012-08-081-1/+8
* [mcs814x] cleanup image generationflorian2012-08-081-4/+8
* [lantiq] pci gpio mappingblogic2012-08-081-4/+4
* bcm63xx: fix USB base registers and IRQs for BCM6328jogo2012-08-0510-12/+100
* [brcm47xx] update tg3 driverhauke2012-08-051-75/+128
* [brcm47xx] generate image for Linksys e3200hauke2012-08-051-0/+1
* brcm47xx: update gpio patchhauke2012-08-052-10/+8
* brcm47xx: fix patch which moves the flash struct in wgt634u codehauke2012-08-052-12/+29
* [lantiq] W502V/ARV4525 wireless mac bugfixblogic2012-08-041-4/+1
* brcm47xx: use libgpio instaed of implementing the gpio interface ourself.hauke2012-08-048-111/+712
* [lantiq] cleanup patchesblogic2012-08-03209-82080/+146978
* [mcs814x] nuport-mac: properly protect the phy interrupt handlerflorian2012-08-021-2/+8
* [bufferbloat] Codel: avoid a nul rec_inv_sqrtblogic2012-08-021-0/+68
* [lantiq] fixes i2c clock enableblogic2012-08-021-0/+32
* ar71xx: simplify misc IRQ handlingjuhosg2012-08-021-0/+66
* ar71xx: fix AR934X_EHCI_SIZEjuhosg2012-08-024-4/+4
* ar71xx: image: stop the switch from the lzma-loader on the TL-WR1043NDjuhosg2012-08-022-0/+745
* ar71xx: image: allow to use board specific code in the lzma-loaderjuhosg2012-08-023-3/+10
* ar71xx: init switch hw_reset on the TL-WR1043ND boardjuhosg2012-08-021-2/+15
* generic: rtl836x: add hw_reset field to struct rtl8366_smijuhosg2012-08-027-2/+35
* generic: rtl8366_smi: use __rtl8366_smi_cleanup instead of gpio_free callsjuhosg2012-08-021-2/+1
* [mcs814x] add missing netmask to the network configflorian2012-08-011-0/+1
* [mcs814x] assume the link is up and full-duplex by defaultflorian2012-08-011-2/+2
* [mcs814x] add a default and suitable network config fileflorian2012-08-011-0/+12
* ar71xx: ew-dorin: added router firmware generationjuhosg2012-08-016-5/+49
* ar71xx: ew-dorin: added USB supportjuhosg2012-08-011-1/+3
* ar71xx: Buffalo WLAE-AG300N wireless led patchjuhosg2012-08-011-0/+4
* ar71xx: Buffalo WLAE-AG300N initial supportjuhosg2012-08-018-7/+156
* [mcs814x] resync defconfig enable XZ compressionflorian2012-08-011-7/+1
* [mcs814x] properly generate squashfs, jffs2 and initramfs images and kernelsflorian2012-07-312-16/+9
* [kernel] disable crashlog on ARM platforms for the momentflorian2012-07-311-1/+1
* [lantiq] add lantiq svip supportblogic2012-07-3122-53/+17723
* bcm63xx: Add nb6 support (BCM6362 SoC base boards)jogo2012-07-3110-6/+191
* bcm63xx: add basic bcm6362 supportjogo2012-07-3118-14/+1008
* bcm63xx: enable usb for bcm6328jogo2012-07-311-0/+60
* bcm63xx: update enetswitch driverjogo2012-07-3131-44/+452
* bcm63xx: reorder patchesjogo2012-07-3113-17/+17
* [at91] move i2c module to target modules.mkflorian2012-07-291-0/+17
* [omap24xx] resync configflorian2012-07-291-20/+0
* [omap24xx] use the same description as other omap platforms (without the dash)florian2012-07-291-1/+1
* [kernel] refresh pwm patchblogic2012-07-291-9/+5
* [kernel] clean up pwm patches and driversblogic2012-07-285-608/+28
* [kernel] add config option CONFIG_I2C_MV64XXX to fix kirkwood buildhauke2012-07-281-0/+1
* [realview] resync configflorian2012-07-271-4/+0
* [brcm63xx] fix DVA-G3810BN image generationflorian2012-07-271-1/+1
* [brcm63xx] add D-link DVA-G3810BN-TL-1 supportflorian2012-07-272-2/+84