| Commit message (Collapse) | Author | Age | Files | Lines |
|
|
|
| |
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28043 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
|
|
| |
on some platforms, erase suspend leads to data corruption and lockups when write
ops collide with erase ops. this has been observed on the buffalo wzr-hp-g300nh.
rather than play whack-a-mole with a hard to reproduce issue on a variety of devices,
simply disable erase suspend, as it will usually not produce any useful gain on
the small filesystems used on embedded hardware.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27984 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
| |
KanjiMonster did the right patch, I was just confused because of linux-3.0 and linux-2.6.30
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27954 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
| |
find_task_by_vpid is already exported by the kernel without any patches needed.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27953 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
| |
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27945 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
| |
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27927 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
| |
some rules containing only source/destination address checks
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27923 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
| |
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27918 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
| |
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27909 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
| |
This is breaking some devices out there such as Winchiphead CH341 adapters (#9601)
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27885 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
| |
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27879 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
| |
and 3.0
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27840 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
|
| |
Issue map read after Write Buffer Load command to ensure chip is ready
to receive data.
Signed-off-by: George Kashperko <george@znau.edu.ua>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27760 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
| |
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27759 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Fixes problem with TFM allocation in cryptosoft.c
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
Hauke:
* remove ubsec_ssb package and take it from ocf-linux
* use patches from ocf-linux package
* refresh all patches
* readd some build fixes for OpenWrt.
* readd CRYPTO_MANAGER dependency
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27753 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
| |
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27736 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
| |
* add new patches for bcm4716 SoC
* add support for serial flash on bcma bus
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27723 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
| |
Thank you Peter Wagner for the patch
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27722 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
| |
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27600 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
| |
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27557 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
| |
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27527 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
| |
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27524 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
| |
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27518 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
| |
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27491 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
| |
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27490 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
| |
support a lot of not-yet-upstreamed stuff
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27485 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
| |
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27457 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
| |
unlocked_ioctl on all platforms and fix the arguments to the ioctl handler (based on patch from #9198)
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27322 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
| |
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27300 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
| |
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27299 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
| |
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27293 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
| |
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27247 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Since 2.6.38 the bridge module has a dependency to IPv6 if IPv6 is
enabled. Since the IPv6 module isn't exactly lightweight and bridge also
only needs a single function from IPv6, it's rather easy to create a
common "lib" module with a RCU pointer to the actual implementation, if
the IPv6 module is loaded (although slightly hackish).
The codepath seems to be only taken when using IPv6, so there should be
no negative side effects when IPv6 isn't loaded. I did not measure how
big the performance impact is.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27237 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
Also make linux identify itself properly as 3.0, not 3.0.0.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27191 3c298f89-4303-0410-b956-a3cf2f4a3e73
|