rtl819xx - Realtek rtl819xx port to OpenWrt

	Commit message (Collapse)	Author	Age	Files	Lines
*	[brcm63xx] refresh patches	florian	2012-07-03	1	-1/+1
\| \| \| \|	git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32581 3c298f89-4303-0410-b956-a3cf2f4a3e73
*	[brcm63xx] fix watchdog and rng drivers section mismatch (#11767)	florian	2012-06-29	3	-2/+22
\| \| \| \|	git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32522 3c298f89-4303-0410-b956-a3cf2f4a3e73
*	[brcm63xx] fix SPI clock frequency selection	florian	2012-06-27	1	-1/+1
\| \| \| \|	git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32512 3c298f89-4303-0410-b956-a3cf2f4a3e73
*	[brcm63xx] fix SPI message control handling for BCM6338/6348	florian	2012-06-17	5	-5/+133
\| \| \| \| \| \| \| \| \|	BCM6338 and BCM6338 have their MSG_CONTROL register width of 8-bits instead of 16-bits. We were previously using a 16-bits write which corrupted the first byte of the TX FIFO. Also the message type was always set to Full-duplex even in the case of half-duplex messages. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32409 3c298f89-4303-0410-b956-a3cf2f4a3e73
*	bcm63xx: readd accidentially dropped ignore_oc in ehci driver	jogo	2012-06-11	1	-2/+3
\| \| \| \| \| \|	fixes overcurrent warning spam on 3.3 kernels for bcm63xx again. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32221 3c298f89-4303-0410-b956-a3cf2f4a3e73
*	[brcm63xx] fix 553-board_96348w3.patch patch wrt gpio-keys-polled	florian	2012-06-06	1	-1/+1
\| \| \| \|	git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32096 3c298f89-4303-0410-b956-a3cf2f4a3e73
*	[brcm63xx] fix alarm led color for board 96348A-122	florian	2012-06-06	1	-1/+1
\| \| \| \|	git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32089 3c298f89-4303-0410-b956-a3cf2f4a3e73
*	[brcm63xx] add 96348w3 board (#10764)	florian	2012-06-06	2	-2/+70
\| \| \| \|	git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32088 3c298f89-4303-0410-b956-a3cf2f4a3e73
*	[brcm63xx] update livebox board support (#8677)	florian	2012-06-06	1	-62/+200
\| \| \| \| \| \| \| \| \| \| \| \| \| \|	Merge most fixes from #8677: - add basic hardware detection of Livebox Blue 5g revisions - register leds and gpio buttons - fix boot address location - properly parse mac addresses Plus some more fixes: - make board_livebox.c more in line with board_bcm963xx.c git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32087 3c298f89-4303-0410-b956-a3cf2f4a3e73
*	[brcm63xx] fix leds naming for all bcm63xx boards	florian	2012-06-06	26	-166/+429
\| \| \| \|	git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32086 3c298f89-4303-0410-b956-a3cf2f4a3e73
*	[brcm63xx] backport upstream spi-bcm63xx fixes	florian	2012-06-06	3	-0/+381
\| \| \| \| \| \| \| \|	* message pump conversion * not using stopping state * setting spi driver mode bits git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32078 3c298f89-4303-0410-b956-a3cf2f4a3e73
*	[brcm63xx] increase led number in patch 301-led_count.patch	florian	2012-06-06	4	-33/+11
\| \| \| \| \| \|	So that board patches are only touching board-related code git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32076 3c298f89-4303-0410-b956-a3cf2f4a3e73
*	[brcm63xx] fix board patches so that new boards are withing appropriate ifdef	florian	2012-06-05	39	-111/+133
\| \| \| \| \| \| \|	Some new board definitions were added within the #ifdef CONFIG_CPU_6338 section while some other were added within #ifdef CONFIG_CPU_6345, fix this git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32060 3c298f89-4303-0410-b956-a3cf2f4a3e73
*	[brcm63xx] fix bisectability of patch 303-spi-board-info.patch	florian	2012-06-05	1	-1/+9
\| \| \| \| \| \| \|	It uses spi_register_board_info() from linux/spi/spi.h but does not include it explicitely. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32058 3c298f89-4303-0410-b956-a3cf2f4a3e73
*	bcm63xx: fix ethernet on 96328avng and 963281TAN	jogo	2012-06-04	7	-15/+19
\| \| \| \| \| \|	The internal switch did not get registered. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32041 3c298f89-4303-0410-b956-a3cf2f4a3e73
*	bcm63xx: build images for 6328 reference boards with various flash sizes	jogo	2012-05-30	7	-27/+214
\| \| \| \| \| \| \| \| \| \| \|	Build images for 96328avng and 963281TAN (untested) for three different flash sizes: 4MB, 8MB, and 16MB. Known issues: * Button setup unknown, thus no fail-safe available. * All other BCM6328 and BCM63XX issues git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32004 3c298f89-4303-0410-b956-a3cf2f4a3e73
*	bcm63xx: add support for DSL-274XB rev F1	jogo	2012-05-27	5	-5/+142
\| \| \| \|	git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31882 3c298f89-4303-0410-b956-a3cf2f4a3e73
*	bcm63xx: fix port state after network down	jogo	2012-05-27	1	-0/+28
\| \| \| \| \| \| \| \|	bcm_enetsw_probe did not properly reset port states, resulting in connected ports staying disabled after bringing up the interface the second time. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31881 3c298f89-4303-0410-b956-a3cf2f4a3e73
*	bcm63xx: add a fixup for ath9k devices	jogo	2012-05-27	23	-63/+1447
\| \| \| \|	git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31880 3c298f89-4303-0410-b956-a3cf2f4a3e73
*	bcm63xx: add support for the HSSPI controller	jogo	2012-05-27	32	-55/+1240
\| \| \| \| \| \| \|	Add support for the HSSPI controller found on bcm6328 and SPI attached flash. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31879 3c298f89-4303-0410-b956-a3cf2f4a3e73
*	bcm63xx: add preliminary support for bcm6328	jogo	2012-05-27	20	-16/+1360
\| \| \| \|	git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31878 3c298f89-4303-0410-b956-a3cf2f4a3e73
*	bcm63xx: add flash type detection	jogo	2012-05-27	32	-80/+414
\| \| \| \|	git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31877 3c298f89-4303-0410-b956-a3cf2f4a3e73
*	kernel: update linux 3.3 to 3.3.5	juhosg	2012-05-07	7	-8/+8
\| \| \| \|	git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31645 3c298f89-4303-0410-b956-a3cf2f4a3e73
*	bcm63xx: fix a race between PCI bus scan and fallback sprom registration	jogo	2012-05-06	2	-0/+110
\| \| \| \| \| \| \| \| \|	The fallback sprom handler was installed too late, resulting in ssb failing to get a valid sprom on some devices. Fixes #11384. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31638 3c298f89-4303-0410-b956-a3cf2f4a3e73
*	[brcm63xx] use a define for the poll and debounce interval	florian	2012-05-02	35	-98/+111
\| \| \| \|	git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31550 3c298f89-4303-0410-b956-a3cf2f4a3e73
*	kernel: update linux 3.3 to 3.3.4	juhosg	2012-04-30	4	-4/+4
\| \| \| \|	git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31541 3c298f89-4303-0410-b956-a3cf2f4a3e73
*	[brcm63xx] switch to gpio-keys-polled	florian	2012-04-27	15	-41/+41
\| \| \| \|	git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31491 3c298f89-4303-0410-b956-a3cf2f4a3e73
*	bcm63xx: add initial support for bcm6368 boards	jogo	2012-03-28	4	-3/+225
\| \| \| \|	git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31132 3c298f89-4303-0410-b956-a3cf2f4a3e73
*	bcm63xx: add driver for the internal hw trng on bcm6368	jogo	2012-03-28	8	-7/+469
\| \| \| \|	git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31131 3c298f89-4303-0410-b956-a3cf2f4a3e73
*	bcm63xx: replace SPI driver with latest upstream version	jogo	2012-03-28	24	-942/+1335
\| \| \| \|	git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31130 3c298f89-4303-0410-b956-a3cf2f4a3e73
*	bcm63xx: add ethernet support for bcm6368	jogo	2012-03-28	11	-534/+2173
\| \| \| \| \| \| \| \| \|	Add basic support for the internal ethernet switch on bcm6368. It behaves as a dumb switch for now, but allows basic connectivity. Also drop the ethernet patch for bcm6345 for now, it needs rework. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31129 3c298f89-4303-0410-b956-a3cf2f4a3e73
*	bcm63xx: add missing bits from extirq support	jogo	2012-03-28	4	-3/+99
\| \| \| \| \| \|	Add missing external IRQ code parts for older chips in the new code. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31128 3c298f89-4303-0410-b956-a3cf2f4a3e73
*	bcm63xx: reorder patches	jogo	2012-03-28	40	-76/+76
\| \| \| \| \| \| \|	Reorder patches for a clearer distinction between the purposes of the different patches. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31127 3c298f89-4303-0410-b956-a3cf2f4a3e73
*	[brcm63xx] remove udc patch since it is unused	florian	2012-03-13	29	-311/+65
\| \| \| \|	git-svn-id: svn://svn.openwrt.org/openwrt/trunk@30920 3c298f89-4303-0410-b956-a3cf2f4a3e73
*	[brcm63xx] wire bcm96348gw-10 reset button (#10854)	florian	2012-03-05	2	-2/+22
\| \| \| \|	git-svn-id: svn://svn.openwrt.org/openwrt/trunk@30820 3c298f89-4303-0410-b956-a3cf2f4a3e73
*	Merge branch 'bcm63xx'	florian	2012-03-05	8	-10/+153
\| \| \| \|	git-svn-id: svn://svn.openwrt.org/openwrt/trunk@30819 3c298f89-4303-0410-b956-a3cf2f4a3e73
*	brcm63xx: add support for linux 3.3	jogo	2012-02-04	37	-0/+4920
	git-svn-id: svn://svn.openwrt.org/openwrt/trunk@30027 3c298f89-4303-0410-b956-a3cf2f4a3e73