summaryrefslogtreecommitdiffstats
path: root/target/linux/ar71xx/files/drivers
Commit message (Expand)AuthorAgeFilesLines
...
* ar71xx: ag71xx: detect the built-in switch of the AR934X SoCsjuhosg2011-12-151-12/+36
* ar71xx: introduce ar71xx_switch_datajuhosg2011-12-152-5/+8
* ar71xx: tplinkpart: allow to detect JFFS2 as welljuhosg2011-12-151-3/+4
* ar71xx: ag71xx: check PHY IDs before accessing the switch registersjuhosg2011-12-151-9/+8
* ar71xx: ag71xx: don't use port 4 of the switch, it is not connected on ar724xjuhosg2011-12-151-13/+25
* ar71xx: ag71xx: nuke ar7240sw_initjuhosg2011-12-151-6/+1
* ar71xx: check squashfs signature in TP-Link mtd parserjuhosg2011-12-051-1/+31
* ar71xx: add mtd partition parser for the TP-Link boardsjuhosg2011-12-031-0/+165
* ar71xx: add AR71XX_ prefix to GPIO_REG_* definesjuhosg2011-11-141-36/+40
* ar71xx: merge nand scan patchjuhosg2011-11-142-2/+2
* ar71xx: ag71xx: add support for getting switch port link statusjuhosg2011-11-131-0/+67
* ar71xx: ag71xx: remove unused mii_ctrl field from struct ag71xxjuhosg2011-11-132-19/+1
* ar71xx: ag71xx: remove unused mii_cfg related functions and definesjuhosg2011-11-131-40/+0
* ar71xx: set MII interface speed from the set_speed callbacksjuhosg2011-11-131-6/+0
* ar71xx: rename set_pll callback to set_speed in ag71xx_platform_datajuhosg2011-11-131-2/+2
* ar71xx: ag71xx: remove MII interface setup codejuhosg2011-11-132-15/+0
* ar71xx: ag71xx: use fixed link parameters if the mii bus is not registeredjuhosg2011-11-121-0/+4
* ar71xx: remove dead codenbd2011-11-081-15/+0
* ar71xx: on ar7240, exclude ports from their own port vlan destination masknbd2011-11-081-2/+1
* ag71xx: close a race between the phy state machine and link statejogo2011-10-081-3/+7
* ar71xx: fix register range check for DMA stuck checks (thx, Frédéric Moulins)nbd2011-09-111-1/+1
* ar71xx: add some code to detect DMA stuck conditions on ar7240nbd2011-08-132-1/+33
* ar71xx: on ar724x only reset the link status in the restart handler, the fast...nbd2011-08-131-0/+6
* ar71xx: fix ethernet FIFO state corruption on ar7240nbd2011-08-042-20/+61
* ag71xx: fix memory corruption issues on ar7240 on ethernet start/stopnbd2011-08-042-3/+19
* ar71xx: fix MAC/MDIO reset mask handlingnbd2011-08-041-2/+2
* ar71xx: reinitialize global switch settings after reset on ar7240nbd2011-07-201-23/+24
* ar71xx: configure address aging on ar7240nbd2011-07-201-2/+12
* ar71xx: reset the phy in the ethernet init on ar724xnbd2011-07-201-0/+13
* ar71xx: make sure that rx and interrupts are disabled before issuing the hard...nbd2011-07-201-7/+9
* ar71xx: increase the delay after the ethernet MAC resetnbd2011-07-201-1/+1
* ar71xx: fix an unused variable warningnbd2011-07-201-1/+0
* ar71xx: do not reset the hardware on transmit timeout - this would mess up th...nbd2011-07-091-4/+0
* ag71xx: keep the rx engine stopped while the link is not up, should hopefully...nbd2011-07-091-91/+91
* ar71xx: merge 2.6.39 patchesjuhosg2011-06-291-678/+0
* ar71xx: add 2.6.39 supportjuhosg2011-06-291-0/+688
* ar71xx: cleanup AR933X UART driverjuhosg2011-06-191-481/+141
* ar71xx: use ar933x_uart.h in the AR933X serial driverjuhosg2011-06-131-339/+75
* ar71xx: setup wdt_clock for AR913X to avoid a kernel bugjuhosg2011-06-041-0/+2
* Revert "ar71xx: only enable the rx engine after the link is up..."nbd2011-06-011-68/+67
* ar71xx: add serial driver for the AR933X UARTjuhosg2011-05-311-0/+1282
* ar71xx: the watchdog uses the reference clock on the AR933x SoCsjuhosg2011-05-311-2/+12
* ar71xx: Fix header offset for newer WRT160NL modelsjuhosg2011-05-311-9/+16
* ar71xx: ag71xx: make ring sizes configurable via ethtooljuhosg2011-05-312-0/+56
* ar71xx: ag71xx: prepare to make ring sizes configurablejuhosg2011-05-313-35/+32
* ar71xx: ag71xx: nuke unused AG71XX_TX_FIFO_LEN definejuhosg2011-05-311-1/+0
* ar71xx: only enable the rx engine after the link is up, fixes a race conditio...nbd2011-05-301-67/+68
* ar71xx: disable flow control for ar724x, it can get stuck in a loop of contin...nbd2011-05-301-5/+1
* ar71xx: detect link on LAN portsmatteo2011-05-173-3/+32
* use correct macros and frame size in ag71xxmatteo2011-05-141-3/+2