summaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
...
* [brcm63xx] Remove invalid LED GPIO from GW6200 board definition. GPIO 35 ↵cshore2012-01-1113-40/+25
| | | | | | isn't intended to control ethernet LED (the led behaviour is a side effect) and using the gpio as an led causes kernel panics. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29712 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: disable ath79 in order to get rid of Kconfig warningsjuhosg2012-01-111-0/+11
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29711 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: pb44_spi: add shutdown handlerjuhosg2012-01-111-0/+10
| | | | | | This allows to access the flash from a kexec'd kernel. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29710 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: pb44_spi: call pb44_spi_{en,dis}able from probe/removejuhosg2012-01-111-6/+4
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29709 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: pb44_spi: introduce pb44_spi_{en,dis}able helpersjuhosg2012-01-111-8/+17
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29708 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: ar71xx_spi: add shutdown handlerjuhosg2012-01-111-0/+10
| | | | | | This allows to access the flash from a kexec'd kernel. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29707 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: ar71xx_spi: save and restore regs from probe/removejuhosg2012-01-111-17/+7
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29706 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: ar71xx_wdt: add shutdown handlerjuhosg2012-01-111-0/+6
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29705 3c298f89-4303-0410-b956-a3cf2f4a3e73
* [include] cmake.mk: fix passing of LDFLAGSjow2012-01-091-3/+4
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29701 3c298f89-4303-0410-b956-a3cf2f4a3e73
* [include] make prepare_kernel_conf target depend on quilt instead of sed. ↵jow2012-01-081-2/+2
| | | | | | Preparing the source tree requires quilt and installing quilt implies installing sed. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29697 3c298f89-4303-0410-b956-a3cf2f4a3e73
* [scripts] metadata.pl: filter direct recursive depends like "select ↵jow2012-01-081-0/+1
| | | | | | PACKAGE_kmod-ipv6 if PACKAGE_kmod-ipv6" git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29695 3c298f89-4303-0410-b956-a3cf2f4a3e73
* [package] pptp: remove support for underlying ipproto, it is adviced since a ↵jow2012-01-082-6/+2
| | | | | | while that pptp should be declared as separate interface alognside wan - in this configuration the ipproto will cause stray udhcpc errors due to not existent interfaces, so remove it git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29694 3c298f89-4303-0410-b956-a3cf2f4a3e73
* [package] cyassl: use patch-libtool pkg fixupjow2012-01-081-1/+1
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29693 3c298f89-4303-0410-b956-a3cf2f4a3e73
* zlib: fix duplicate function declarations for largefile supportnbd2012-01-081-0/+48
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29690 3c298f89-4303-0410-b956-a3cf2f4a3e73
* [toolchain] introduce a USE_EXTERNAL_LIBC symbol which gets selected by ↵jow2012-01-081-1/+5
| | | | | | | | | | | EXTERNAL_TOOLCHAIN || NATIVE_TOOLCHAIN Currently we always assume uClibc if an external toolchain is used, this breaks for non-uClibc toolchains or even vanilla uClibc ones since they do not share the external librpc semantics as OpenWrt. Solve the problem by defining an abstract "EXTERNAL_LIBC" which packages might or might not depend on. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29689 3c298f89-4303-0410-b956-a3cf2f4a3e73
* [package] base-files: implement a --force option for sysupgrade to override ↵jow2012-01-082-4/+13
| | | | | | image checks, useful to upgrade old ar71xx installations to current trunk ones git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29688 3c298f89-4303-0410-b956-a3cf2f4a3e73
* [package] firewall: add support for "local" port forwards which target an ↵jow2012-01-082-4/+15
| | | | | | internal address on the router itself git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29687 3c298f89-4303-0410-b956-a3cf2f4a3e73
* include: calculate md5sum over sorted kernel config symbol list and ↵jow2012-01-083-2/+7
| | | | | | | | | | incorperate it into the kernel metapackage version, make kmods depend on this specific version. The aim of this change is to invalidate kmods which are built against a different kernel config on the opkg metadata level. Manual copying and insmod of custom *.ko files, e.g. for development purpose, is still possible. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29686 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ath9k: merge a channel change fix from linux-wirelessnbd2012-01-074-13/+45
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29684 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: refresh patchesjuhosg2012-01-072-4/+4
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29683 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: add a profile and build images for the TL-WR2543N/NDjuhosg2012-01-072-0/+17
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29682 3c298f89-4303-0410-b956-a3cf2f4a3e73
* firware-utils/mktplinkfw: add TL-WR2543N/ND supportjuhosg2012-01-071-0/+12
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29681 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: add initial support for the TL-WR2543N/ND boardjuhosg2012-01-0710-1/+164
| | | | | | The WLAN LEDs are not working yet. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29680 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: allow to specify max read size for m25p80juhosg2012-01-071-0/+112
| | | | | | | | | | | | | | | Reading from the flash chip on the TL-WR2543ND seems buggy. If the SPI flash driver tries to read too much data in one SPI transfer, the flash chip returns bogus values. This can be caused by a buggy flash chip on my board, or it can be a bug in our SPI driver. Add a workaround to the m25p80 driver until I find out the root cause of the problem. The patch allows to specify the maximum numner of bytes which can be read safely withint one SPI transfer. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29679 3c298f89-4303-0410-b956-a3cf2f4a3e73
* generic: add driver for the RTL8367R/M switchesjuhosg2012-01-078-0/+1955
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29678 3c298f89-4303-0410-b956-a3cf2f4a3e73
* generic: rtl8366: preparing for RTL8367 supportjuhosg2012-01-074-9/+17
| | | | | | | | * make clock delay configurable * make read,write commands configurable * use u16 for member and untag fields git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29677 3c298f89-4303-0410-b956-a3cf2f4a3e73
* generic: rtl8366_smi: add timeout messagejuhosg2012-01-071-2/+4
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29676 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: local mac support on the wndr3700juhosg2012-01-071-2/+13
| | | | | | | | | | | | | | The wndr3700 at least has no eth0 mac address and usually leverages the first wireless device's mac when in a bridged scenario. If, however, you want to route, and not bridge the interfaces, you need a unique mac address for it. This patch sets the local bit on the mac address pulled from the wireless chip and uses the resulting address for eth0. Patch-by: Dave Taht <dave.taht@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29675 3c298f89-4303-0410-b956-a3cf2f4a3e73
* generic: improve MIPS kexec supportjuhosg2012-01-0719-1/+3553
| | | | | | | | | | | | | It is based on patches from the linux-longsoon-community git tree: http://dev.lemote.com/cgit/linux-loongson-community.git/ Now the kernel can use the command line parameter from kexec-tools. Runtime tested on ar71xx with 2.6.39.4 (the wathdog must be stopped before executing the new kernel). Compile tested with lantiq (3.1.4) and brcm47xx (3.0.12). git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29674 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: fix sysupgrade on the TL-WR841N/ND v7 boardsjuhosg2012-01-061-0/+1
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29672 3c298f89-4303-0410-b956-a3cf2f4a3e73
* [package] openssl: bump to v1.0.0f (CVE-2011-4108, CVE-2011-4576, ↵jow2012-01-061-3/+3
| | | | | | CVE-2011-4577, CVE-2011-4619, CVE-2012-0027) git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29670 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: add support for Redwave RW2458Njuhosg2012-01-0610-0/+143
| | | | | | Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29669 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: fix RB-750 network configurationjuhosg2012-01-061-1/+1
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29668 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: fix sections mismatch warnings in the nand driversjuhosg2012-01-052-2/+2
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29667 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: fix LED configuration on the RB-750juhosg2012-01-051-1/+5
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29666 3c298f89-4303-0410-b956-a3cf2f4a3e73
* package/kernel: add package for the PCF2123 RTC driverjuhosg2012-01-041-0/+16
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29664 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: create profile and build image for the ALFA AP96 boardjuhosg2012-01-042-0/+18
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29663 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: add inital support for the ALFA Network AP96 boardjuhosg2012-01-048-1/+172
| | | | | | | | The microSD slot and the Real Time Clock is not working yet. The miniPCIe interface is not tested due to the lack of a suitable card. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29662 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: specify console kernel parameter for the Compex boardsjuhosg2012-01-041-7/+9
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29660 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: allow to use the command line hack on compex devicesjuhosg2012-01-041-29/+31
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29659 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: use the TL-MR3x20 code for the TL-WR841N/ND v7juhosg2012-01-046-13/+40
| | | | | | | These models are based on the AP99 reference board, and uses the AR7241 SoC. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29658 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: show correct model name on TL-WA701N/ND boardsjuhosg2012-01-041-0/+3
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29657 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: add profile and build image for the TL-WA701N/ND boardsjuhosg2012-01-042-0/+17
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29656 3c298f89-4303-0410-b956-a3cf2f4a3e73
* firmware-utils/mktplinkfw: add support for TL-WA701N/NDjuhosg2012-01-041-0/+6
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29655 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: fix network configuration for the TL-WA901N/ND boardsjuhosg2012-01-041-5/+1
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29654 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: allow to use LAN LED on the TL-WA901N/ND boardsjuhosg2012-01-042-0/+15
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29653 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: add default LED configuration for the TL-MR3020juhosg2012-01-042-0/+6
| | | | | | Also use the system LED for diagnostic. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29652 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: add support for TP-Link TL-MR3020juhosg2012-01-0410-0/+160
| | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the TP-Link device TL-MR3020 which is very similiar to the TL-WR703N. The TL-MR3020 uses 5 LEDs, 1 push button and a switch with 3 positions. Only four LEDs can be controlled via GPIO. The power LED is connected to the power supply. The WPS push button has been mapped to KEY_WPS_BUTTON. The two GPIO signals of the sliding switch have been mapped to BTN_0 and BTN_1. I have also setup a wiki page with details here: http://wiki.openwrt.org/toh/tp-link/tl-mr3020 USB is working and has been tested with USB mass storage and USB UMTS stick. Wifi also seems to work. Ethernet is working too. Signed-off-by: Christian Cier-Zniewski <c.cier@gmx.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29651 3c298f89-4303-0410-b956-a3cf2f4a3e73
* firmware-utils/mktplinkfw: add support for TL-MR3020juhosg2012-01-041-0/+6
| | | | | | Signed-off-by: Christian Cier-Zniewski <c.cier@gmx.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29650 3c298f89-4303-0410-b956-a3cf2f4a3e73
* package: remove the om2p-watchdog packagejuhosg2012-01-043-73/+0
| | | | | | Signed-off-by: Antonio Quartulli <ordex@autistici.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29649 3c298f89-4303-0410-b956-a3cf2f4a3e73
generated by cgit v1.2.3 (git 2.25.1) at 2024-12-28 05:47:25 +0000