summaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* firware-utils/mktplinkfw: add TL-WR2543N/ND supportjuhosg2012-01-071-0/+12
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29681 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: add initial support for the TL-WR2543N/ND boardjuhosg2012-01-0710-1/+164
| | | | | | The WLAN LEDs are not working yet. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29680 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: allow to specify max read size for m25p80juhosg2012-01-071-0/+112
| | | | | | | | | | | | | | | Reading from the flash chip on the TL-WR2543ND seems buggy. If the SPI flash driver tries to read too much data in one SPI transfer, the flash chip returns bogus values. This can be caused by a buggy flash chip on my board, or it can be a bug in our SPI driver. Add a workaround to the m25p80 driver until I find out the root cause of the problem. The patch allows to specify the maximum numner of bytes which can be read safely withint one SPI transfer. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29679 3c298f89-4303-0410-b956-a3cf2f4a3e73
* generic: add driver for the RTL8367R/M switchesjuhosg2012-01-078-0/+1955
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29678 3c298f89-4303-0410-b956-a3cf2f4a3e73
* generic: rtl8366: preparing for RTL8367 supportjuhosg2012-01-074-9/+17
| | | | | | | | * make clock delay configurable * make read,write commands configurable * use u16 for member and untag fields git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29677 3c298f89-4303-0410-b956-a3cf2f4a3e73
* generic: rtl8366_smi: add timeout messagejuhosg2012-01-071-2/+4
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29676 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: local mac support on the wndr3700juhosg2012-01-071-2/+13
| | | | | | | | | | | | | | The wndr3700 at least has no eth0 mac address and usually leverages the first wireless device's mac when in a bridged scenario. If, however, you want to route, and not bridge the interfaces, you need a unique mac address for it. This patch sets the local bit on the mac address pulled from the wireless chip and uses the resulting address for eth0. Patch-by: Dave Taht <dave.taht@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29675 3c298f89-4303-0410-b956-a3cf2f4a3e73
* generic: improve MIPS kexec supportjuhosg2012-01-0719-1/+3553
| | | | | | | | | | | | | It is based on patches from the linux-longsoon-community git tree: http://dev.lemote.com/cgit/linux-loongson-community.git/ Now the kernel can use the command line parameter from kexec-tools. Runtime tested on ar71xx with 2.6.39.4 (the wathdog must be stopped before executing the new kernel). Compile tested with lantiq (3.1.4) and brcm47xx (3.0.12). git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29674 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: fix sysupgrade on the TL-WR841N/ND v7 boardsjuhosg2012-01-061-0/+1
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29672 3c298f89-4303-0410-b956-a3cf2f4a3e73
* [package] openssl: bump to v1.0.0f (CVE-2011-4108, CVE-2011-4576, ↵jow2012-01-061-3/+3
| | | | | | CVE-2011-4577, CVE-2011-4619, CVE-2012-0027) git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29670 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: add support for Redwave RW2458Njuhosg2012-01-0610-0/+143
| | | | | | Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29669 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: fix RB-750 network configurationjuhosg2012-01-061-1/+1
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29668 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: fix sections mismatch warnings in the nand driversjuhosg2012-01-052-2/+2
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29667 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: fix LED configuration on the RB-750juhosg2012-01-051-1/+5
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29666 3c298f89-4303-0410-b956-a3cf2f4a3e73
* package/kernel: add package for the PCF2123 RTC driverjuhosg2012-01-041-0/+16
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29664 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: create profile and build image for the ALFA AP96 boardjuhosg2012-01-042-0/+18
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29663 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: add inital support for the ALFA Network AP96 boardjuhosg2012-01-048-1/+172
| | | | | | | | The microSD slot and the Real Time Clock is not working yet. The miniPCIe interface is not tested due to the lack of a suitable card. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29662 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: specify console kernel parameter for the Compex boardsjuhosg2012-01-041-7/+9
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29660 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: allow to use the command line hack on compex devicesjuhosg2012-01-041-29/+31
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29659 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: use the TL-MR3x20 code for the TL-WR841N/ND v7juhosg2012-01-046-13/+40
| | | | | | | These models are based on the AP99 reference board, and uses the AR7241 SoC. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29658 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: show correct model name on TL-WA701N/ND boardsjuhosg2012-01-041-0/+3
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29657 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: add profile and build image for the TL-WA701N/ND boardsjuhosg2012-01-042-0/+17
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29656 3c298f89-4303-0410-b956-a3cf2f4a3e73
* firmware-utils/mktplinkfw: add support for TL-WA701N/NDjuhosg2012-01-041-0/+6
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29655 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: fix network configuration for the TL-WA901N/ND boardsjuhosg2012-01-041-5/+1
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29654 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: allow to use LAN LED on the TL-WA901N/ND boardsjuhosg2012-01-042-0/+15
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29653 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: add default LED configuration for the TL-MR3020juhosg2012-01-042-0/+6
| | | | | | Also use the system LED for diagnostic. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29652 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: add support for TP-Link TL-MR3020juhosg2012-01-0410-0/+160
| | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the TP-Link device TL-MR3020 which is very similiar to the TL-WR703N. The TL-MR3020 uses 5 LEDs, 1 push button and a switch with 3 positions. Only four LEDs can be controlled via GPIO. The power LED is connected to the power supply. The WPS push button has been mapped to KEY_WPS_BUTTON. The two GPIO signals of the sliding switch have been mapped to BTN_0 and BTN_1. I have also setup a wiki page with details here: http://wiki.openwrt.org/toh/tp-link/tl-mr3020 USB is working and has been tested with USB mass storage and USB UMTS stick. Wifi also seems to work. Ethernet is working too. Signed-off-by: Christian Cier-Zniewski <c.cier@gmx.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29651 3c298f89-4303-0410-b956-a3cf2f4a3e73
* firmware-utils/mktplinkfw: add support for TL-MR3020juhosg2012-01-041-0/+6
| | | | | | Signed-off-by: Christian Cier-Zniewski <c.cier@gmx.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29650 3c298f89-4303-0410-b956-a3cf2f4a3e73
* package: remove the om2p-watchdog packagejuhosg2012-01-043-73/+0
| | | | | | Signed-off-by: Antonio Quartulli <ordex@autistici.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29649 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: use the new om-watchdog package for OM2Pjuhosg2012-01-041-1/+1
| | | | | | Signed-off-by: Antonio Quartulli <ordex@autistici.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29648 3c298f89-4303-0410-b956-a3cf2f4a3e73
* package: add om-watchdog packagejuhosg2012-01-043-0/+82
| | | | | | | | | | om2p-watchdog package is OM2P specific. However a similar watchdog mechanism exists on OM1P as well. This new package wants to substitute om2p-watchdog with a new one which is suitable either for OM1P and OM2P. Signed-off-by: Antonio Quartulli <ordex@autistici.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29647 3c298f89-4303-0410-b956-a3cf2f4a3e73
* [toolchain] disable UCLIBC_HAS_XLOCALE and UCLIB_HAS_GLIBC_DIGIT_GROUPING if ↵jow2012-01-041-0/+2
| | | | | | BUILD_NLS is on (#10735) git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29646 3c298f89-4303-0410-b956-a3cf2f4a3e73
* add CT target and TTL/HL match+targetjow2012-01-041-0/+4
| | | | | | | | This patch adds the CT target for conntrack (enables manipulation of conntrack events and supercedes NOTRACK) as well as the TTL/HL target and match. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29645 3c298f89-4303-0410-b956-a3cf2f4a3e73
* [netfilter] remove current RTSP supportjow2012-01-0411-12299/+0
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29643 3c298f89-4303-0410-b956-a3cf2f4a3e73
* [generic] backport upstream commit e1738bd9cecc5c867b0e2996470c1ff20f66ba79 ↵jow2012-01-032-0/+82
| | | | | | | | | | | to affected kernels (#9802) commit 8efa88540635 (sch_sfq: avoid giving spurious NET_XMIT_CN signals) forgot to call qdisc_tree_decrease_qlen() to signal upper levels that a packet (from another flow) was dropped, leading to various problems. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29642 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: add profile and build factory image for the Hornet-UB boardjuhosg2012-01-012-13/+24
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29637 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: build images for the ALFA Network N2/N5 boardsjuhosg2012-01-012-0/+41
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29636 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: add support for the ALFA Network N2/N5 boardsjuhosg2012-01-0110-0/+183
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29635 3c298f89-4303-0410-b956-a3cf2f4a3e73
* [package] iwinfo: factor txpower offset into info display output, recompile ↵jow2012-01-012-2/+13
| | | | | | if driver selection changes git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29634 3c298f89-4303-0410-b956-a3cf2f4a3e73
* [toolchain] if CONFIG_BUILD_NLS is selected, compile uClibc with locale supportjow2012-01-012-1/+2
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29633 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: define LAN/WAN LEDs for the TL-WR741N/ND boardsjuhosg2011-12-313-6/+103
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29631 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: enable SWCONFIG_LEDSjuhosg2011-12-311-0/+1
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29630 3c298f89-4303-0410-b956-a3cf2f4a3e73
* package/base-files: add support for the switch LED triggerjuhosg2011-12-312-1/+9
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29629 3c298f89-4303-0410-b956-a3cf2f4a3e73
* package/base-files: use case statement in led init scriptjuhosg2011-12-311-15/+27
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29628 3c298f89-4303-0410-b956-a3cf2f4a3e73
* kernel: swconfig: introduce a generic switch LED triggerjuhosg2011-12-319-3/+385
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29627 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: ag71xx: implement get_port_{link,stats} callbacksjuhosg2011-12-311-0/+142
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29626 3c298f89-4303-0410-b956-a3cf2f4a3e73
* kernel: swconfig: add get_port_{link,stats} callbacksjuhosg2011-12-311-0/+26
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29625 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: fix LEDs on the WRT400Njuhosg2011-12-312-12/+13
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29624 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ramips: rt288x: add support for the Belkin F5D8235-4 v1 boardjuhosg2011-12-2811-1/+184
| | | | | | Patch-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29617 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ramips: rt288x: change base address and window size of flash bank 0juhosg2011-12-281-2/+2
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29616 3c298f89-4303-0410-b956-a3cf2f4a3e73
generated by cgit v1.2.3 (git 2.25.1) at 2024-12-23 14:12:25 +0000