summaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* at91: add missing config symbolsjuhosg2013-04-301-0/+4
| | | | | | Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36492 3c298f89-4303-0410-b956-a3cf2f4a3e73
* linux/3.{8,9}: add missing symbolsjuhosg2013-04-302-0/+4
| | | | | | Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36491 3c298f89-4303-0410-b956-a3cf2f4a3e73
* linux/3.{8,9}: turn on CONFIG_NET_SCH_FQ_CODELjuhosg2013-04-302-2/+2
| | | | | | | | It is forced to 'y' since r36342. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36490 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ramips: move dlink profile to correct sub folder - 2nd tryblogic2013-04-301-0/+0
| | | | | | Signed-off-by: John Crispin <blogic@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36489 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ramips: move dlink profile to correct sub folderblogic2013-04-301-0/+0
| | | | | | Signed-off-by: John Crispin <blogic@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36487 3c298f89-4303-0410-b956-a3cf2f4a3e73
* toolchain: gcc: backport fixes for gcc bug 54295jogo2013-04-293-0/+210
| | | | | | | | | | | | Fix "Widening multiply-accumulate operation uses wrong value extension" for 4.7, 4.7-linaro and 4.6-linaro, which backported the broken code to 4.6. Vanilla 4.6 is unaffected. Fixes #13420. Signed-off-by: Jonas Gorski <jogo@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36486 3c298f89-4303-0410-b956-a3cf2f4a3e73
* [packages] move packages related to telephony into its own feedmirko2013-04-291-0/+1
| | | | | | | remove telephony related packages from packages.svn and add new feed 'telephony.git' to feeds.conf.default git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36485 3c298f89-4303-0410-b956-a3cf2f4a3e73
* broadcom-diag: support for the WNDR3700v3hauke2013-04-284-18/+110
| | | | | | | | | | | | | | | I recently picked up a WNDR3700 to put OpenWRT on, and only after tearing into the box did I find it was one of the v3 boards, with poor OpenWRT support. This patch should add the board detection and LED/button control to the broadcom-diag module, and should generate a netgear .chk image that the bootloader and stock firmware will accept. The changes to the broadcom-diag module are more than a few lines because the WNDR3700v3 is driving its LEDs through an HC164 8-bit shift register. Signed-off-by: Owen Kirby <osk@exegin.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36482 3c298f89-4303-0410-b956-a3cf2f4a3e73
* acx-mac80211: make it compile with recent mac80211 againhauke2013-04-282-1/+28
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36481 3c298f89-4303-0410-b956-a3cf2f4a3e73
* brcm47xx: use kernel 3.8.10 as default kernelhauke2013-04-281-1/+1
| | | | | | | The biggest change with this kernel is a new partition parser. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36480 3c298f89-4303-0410-b956-a3cf2f4a3e73
* broadcom-wl: read channel using wlc on detecthauke2013-04-281-1/+4
| | | | | | | | | | | Hardcoding channel number to 11 is a bad idea, it may be even not available on some devices. If there are two single-band radios, the one for 5GHz doesn't have 11 channel. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36479 3c298f89-4303-0410-b956-a3cf2f4a3e73
* brcm47xx: add board detection for NETGEAR WNDR4500 V2hauke2013-04-282-8/+12
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36478 3c298f89-4303-0410-b956-a3cf2f4a3e73
* mac80211: brcmsmac: remove initial support for core rev 28hauke2013-04-281-75/+0
| | | | | | | To add support for core rev 28 there are a lot more changes needed. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36477 3c298f89-4303-0410-b956-a3cf2f4a3e73
* mac80211: b43: only use gpio 0 and 1 for the wifi ledhauke2013-04-281-0/+17
| | | | | | | sometimes b43 truned the gpio for the switch reset on. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36476 3c298f89-4303-0410-b956-a3cf2f4a3e73
* kernel: fix a memory leak in split_rootfs_data()hauke2013-04-282-42/+20
| | | | | | | allocate_partition() copies all the content of dpart into a new struct. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36475 3c298f89-4303-0410-b956-a3cf2f4a3e73
* mac80211: b43: Handle DMA RX descriptor underrunhauke2013-04-282-0/+156
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36474 3c298f89-4303-0410-b956-a3cf2f4a3e73
* kernel: update bcma and ssb for kernel 3.8+ to version from wireless-testing ↵hauke2013-04-2814-469/+2802
| | | | | | master-2013-04-26. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36473 3c298f89-4303-0410-b956-a3cf2f4a3e73
* iwinfo: fix iwinfo_hardware() return value if chip id is not foundjow2013-04-282-7/+4
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36471 3c298f89-4303-0410-b956-a3cf2f4a3e73
* kernel: update linux 3.9 patches to rc8jogo2013-04-286-76/+12
| | | | | | Signed-off-by: Jonas Gorski <jogo@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36469 3c298f89-4303-0410-b956-a3cf2f4a3e73
* kernel: add missing bcma defines and header file for bcrmfmacjogo2013-04-2815-127/+388
| | | | | | | | Fixes build failure when having kmod-mmc and brcmfmac selected. Signed-off-by: Jonas Gorski <jogo@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36468 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ath9k: fix keycache handling with many connected clientsnbd2013-04-271-0/+27
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36467 3c298f89-4303-0410-b956-a3cf2f4a3e73
* mac80211: refresh patchnbd2013-04-271-1/+1
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36466 3c298f89-4303-0410-b956-a3cf2f4a3e73
* netifd: update to git head - disables multicast snooping by default on bridgesjow2013-04-271-2/+2
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36463 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: add user-space support for WNR2000v3juhosg2013-04-262-1/+5
| | | | | | | Signed-off-by: Mathieu Olivari <mathieu.olivari@gmail.com> Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36461 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: add profile and build image for WNR2000v3juhosg2013-04-262-0/+13
| | | | | | | Signed-off-by: Mathieu Olivari <mathieu.olivari@gmail.com> Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36460 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: Add Netgear WNR2000v3 supportjuhosg2013-04-263-0/+130
| | | | | | | | | | Network connectivity works fine (LAN and WAN). For GPIOs, only pwr led and the green wan leds are supported for now. Signed-off-by: Mathieu Olivari <mathieu.olivari@gmail.com> Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36459 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: add profile and build image for the TL-WR720N v3 boardjuhosg2013-04-262-0/+14
| | | | | | | Signed-off-by: yousong <yszhou4tech@gmail.com> Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36458 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: add user-space support for the TL-WR720N v3 boardjuhosg2013-04-264-1/+10
| | | | | | | Signed-off-by: yousong <yszhou4tech@gmail.com> Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36457 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: add kernel support for TPLINK WR720N v3juhosg2013-04-263-0/+149
| | | | | | | | | | | | | | | Add support for TPLINK WR720N v3 which has 4MB flash, 32MB ram, 2 ethernet interfaces, 1 USB 2.0 port. The patch is mostly a modification from mach-tl-wr703n.c. GPIO numbers for the slider switch is from mach-tl-mr3020n.c. Tested on my device and they worked fine. Signed-off-by: yousong <yszhou4tech@gmail.com> Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36456 3c298f89-4303-0410-b956-a3cf2f4a3e73
* firmware-utils/mktplinkfw: add support for the TL-WR720N v3 boardjuhosg2013-04-261-0/+6
| | | | | | | Signed-off-by: yousong <yszhou4tech@gmail.com> Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36455 3c298f89-4303-0410-b956-a3cf2f4a3e73
* mpc85xx: Add subtargets Generic and P1020juhosg2013-04-265-0/+15
| | | | | | | | | | Only difference between Generic and P1020 is that P1020 enables SMP with two CPUs in the kernel config. Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36454 3c298f89-4303-0410-b956-a3cf2f4a3e73
* kernel: update linux 3.8 to 3.8.9juhosg2013-04-2637-135/+71
| | | | | | Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36453 3c298f89-4303-0410-b956-a3cf2f4a3e73
* at91: upgrade to kernel 3.8.7 and use devicetreejuhosg2013-04-2623-721/+390
| | | | | | | | | | | | | | | This upgrades the AT91 target to 3.8.7, and migrates to device tree. This allows a single kernel to be built for most at91 variants which simplifies things quite a bit. The immediate result is that all subtargets are nuked, and any boards without dts files are no longer supported, though the target now includes more boards than before. The adc driver was also nuked as 3.8.7 includes a new one under the IIO subsystem. Signed-off-by: Adam Porter <porter.adam@gmail.com> Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36452 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ramips: rt3883: fix build errorjuhosg2013-04-262-2/+3
| | | | | | Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36451 3c298f89-4303-0410-b956-a3cf2f4a3e73
* iwinfo: add hw database filejow2013-04-261-0/+55
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36450 3c298f89-4303-0410-b956-a3cf2f4a3e73
* iwinfo: move builtin hardware database to /usr/share/libiwinfo/hardware.txtjow2013-04-264-83/+35
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36449 3c298f89-4303-0410-b956-a3cf2f4a3e73
* mac80211: update to wireless-testing 2013-04-16 + backportsnbd2013-04-2667-3750/+3703
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36448 3c298f89-4303-0410-b956-a3cf2f4a3e73
* procd: fix wrap around bug in logread time handling codeblogic2013-04-251-2/+2
| | | | | | Signed-off-by: John Crispin <blogic@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36447 3c298f89-4303-0410-b956-a3cf2f4a3e73
* hotplug2: make it depend on !PROCD_INITblogic2013-04-251-1/+1
| | | | | | Signed-off-by: John Crispin <blogic@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36446 3c298f89-4303-0410-b956-a3cf2f4a3e73
* lantiq: make leds and network work on VG3503Jblogic2013-04-253-12/+31
| | | | | | Signed-off-by: John Crispin <blogic@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36445 3c298f89-4303-0410-b956-a3cf2f4a3e73
* lantiq: fix board detection helpersblogic2013-04-251-2/+2
| | | | | | Signed-off-by: John Crispin <blogic@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36444 3c298f89-4303-0410-b956-a3cf2f4a3e73
* lantiq: move dts files to thir own folderblogic2013-04-2532-1/+1
| | | | | | Signed-off-by: John Crispin <blogic@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36443 3c298f89-4303-0410-b956-a3cf2f4a3e73
* generic: fix rtl8366_smi compile warningblogic2013-04-251-1/+1
| | | | | | | | | drivers/net/phy/rtl8366_smi.c: In function 'rtl8366_sw_set_vlan_ports': drivers/net/phy/rtl8366_smi.c:1125:6: warning: 'pvid' may be used uninitialized in this function [-Wuninitialized] Signed-off-by: John Crispin <blogic@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36442 3c298f89-4303-0410-b956-a3cf2f4a3e73
* lantiq: disable sw portmaps on xrx200 ethernet as segment solation does not ↵blogic2013-04-251-1/+1
| | | | | | | | work yet Signed-off-by: John Crispin <blogic@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36441 3c298f89-4303-0410-b956-a3cf2f4a3e73
* lantiq: make lzma-loader based images for VG3503Jblogic2013-04-251-13/+21
| | | | | | Signed-off-by: John Crispin <blogic@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36440 3c298f89-4303-0410-b956-a3cf2f4a3e73
* lantiq: update VG3503J.dts to match new partition layoutblogic2013-04-251-3/+3
| | | | | | Signed-off-by: John Crispin <blogic@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36439 3c298f89-4303-0410-b956-a3cf2f4a3e73
* lantiq: add lzma-loader sourceblogic2013-04-2524-0/+2789
| | | | | | Signed-off-by: John Crispin <blogic@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36438 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ramips: add profile for Dlink DIR-615 H1blogic2013-04-251-0/+20
| | | | | | | | | | | | | | | Hello, this adds the profile for Dlink DIR-615 H1 without the usb default packages since this router does not have a usb port and while all the needed definitions for building are already in target/linux/ramips/image/Makefile this also allows users to select the exact target in RT305x based boards menuconfig for this router and compile its firmware. Signed-off-by: Daniel Petre <dani@ip6.ro> Patchwork: http://patchwork.openwrt.org/patch/3529/ Acked-by: John Crispin <blogic@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36437 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ramips: remove now unneeded user-space board detectionblogic2013-04-251-20/+0
| | | | | | | | | | | | Now that ALL5002 and ALL5003 each got their own DTS and board names, remove the now no longer needed user-space part which previously differentiated between ALL5002 and ALL5003. Signed-off-by: Daniel Golle <dgolle@allnet.de> Patchwork: http://patchwork.openwrt.org/patch/3558/ Acked-by: John Crispin <blogic@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36436 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ramips: introduce DTS for ALL5003blogic2013-04-259-4/+133
| | | | | | | | | | | | | Prior to the switch to 3.8, ALL5002 and ALL5003 boards shared mach-all5002.c. With the change to DTS, this is no longer accurate, as ALL5002 is based on Rt3352 SoC while ALL5003 is based on Rt5350 SoC, therefore the corresponding rt5350.dtsi need to be included for ALL5003. Signed-off-by: Daniel Golle <dgolle@allnet.de> Patchwork: http://patchwork.openwrt.org/patch/3557/ Acked-by: John Crispin <blogic@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36435 3c298f89-4303-0410-b956-a3cf2f4a3e73