summaryrefslogtreecommitdiffstats
path: root/target
diff options
context:
space:
mode:
Diffstat (limited to 'target')
-rw-r--r--target/linux/ixp4xx/patches-2.6.26/030-ixp4xx_fsg_board_support.patch47
-rw-r--r--target/linux/ixp4xx/patches-2.6.26/100-gateway7001_mac_plat_info.patch40
-rw-r--r--target/linux/ixp4xx/patches-2.6.26/100-wg302v2_gateway7001_mac_plat_info.patch68
-rw-r--r--target/linux/ixp4xx/patches-2.6.26/101-wg302_mac_plat_info.patch30
-rw-r--r--target/linux/ixp4xx/patches-2.6.26/105-wg302v1_support.patch (renamed from target/linux/ixp4xx/patches-2.6.26/160-wg302v1_support.patch)44
-rw-r--r--target/linux/ixp4xx/patches-2.6.26/110-pronghorn_metro_support.patch289
-rw-r--r--target/linux/ixp4xx/patches-2.6.26/111-pronghorn_metro_mac_plat_info.patch39
-rw-r--r--target/linux/ixp4xx/patches-2.6.26/120-compex_support.patch14
-rw-r--r--target/linux/ixp4xx/patches-2.6.26/130-wrt300nv2_support.patch14
-rw-r--r--target/linux/ixp4xx/patches-2.6.26/140-sidewinder_support.patch16
-rw-r--r--target/linux/ixp4xx/patches-2.6.26/150-lanready_ap1000_support.patch6
-rw-r--r--target/linux/ixp4xx/patches-2.6.26/161-wg302v1_mac_plat_info.patch30
-rw-r--r--target/linux/ixp4xx/patches-2.6.26/162-wg302v1_mem_fixup.patch6
-rw-r--r--target/linux/ixp4xx/patches-2.6.26/180-tw5334_support.patch6
-rw-r--r--target/linux/ixp4xx/patches-2.6.26/190-cambria_support.patch2
-rw-r--r--target/linux/ixp4xx/patches-2.6.26/204-npe_driver_ixp43x_support.patch12
-rw-r--r--target/linux/ixp4xx/patches-2.6.26/400-dmabounce.patch2
17 files changed, 345 insertions, 320 deletions
diff --git a/target/linux/ixp4xx/patches-2.6.26/030-ixp4xx_fsg_board_support.patch b/target/linux/ixp4xx/patches-2.6.26/030-ixp4xx_fsg_board_support.patch
index 8fb7280e0..048b9f746 100644
--- a/target/linux/ixp4xx/patches-2.6.26/030-ixp4xx_fsg_board_support.patch
+++ b/target/linux/ixp4xx/patches-2.6.26/030-ixp4xx_fsg_board_support.patch
@@ -1,50 +1,3 @@
-From: Rod Whitby <rod@whitby.id.au>
-Subject: [PATCH] ixp4xx: Add support for the Freecom FSG-3 board (Patch #4874)
-
-The Freecom-FSG3 is a small network-attached-storage device with the
-following feature set:
-
-* Intel IXP422
-* 4MB Flash (ixp4xx flash driver)
-* 64MB RAM
-* 4 USB 2.0 host ports (ehci and ohci drivers)
-* 1 WAN (eth1) and 3 LAN (eth0) ethernet ports
- * Supported by the open source ixp4xx ethernet driver
-* Via VT6421 disk controller (libata and sata-via drivers)
- * Internal hard disk (PATA supported, SATA not yet supported)
- * External SATA port (not yet supported)
-* ISL1208 RTC chip
-* Winbond 83782 temp sensor and fan controller
-* MiniPCI slot
-
-The ixp4xx_defconfig is also updated to support this device (the
-leds-fsg driver is to be submitted separately via the leds tree after
-this initial support is merged, as it depends on header gpio defines).
-
-Signed-off-by: Rod Whitby <rod@whitby.id.au>
-
-PATCH FOLLOWS
-KernelVersion: v2.6.25-rc6-74-g264e3e8
----
-
-Updated to correct all issues found by RMK.
-
-The front power button calls ctrl_alt_del() and the rear reset button
-now calls machine_restart() directly.
-
- arch/arm/configs/ixp4xx_defconfig | 9 +-
- arch/arm/mach-ixp4xx/Kconfig | 9 +
- arch/arm/mach-ixp4xx/Makefile | 2 +
- arch/arm/mach-ixp4xx/fsg-pci.c | 71 ++++++++
- arch/arm/mach-ixp4xx/fsg-setup.c | 276 ++++++++++++++++++++++++++++++++
- include/asm-arm/arch-ixp4xx/fsg.h | 50 ++++++
- include/asm-arm/arch-ixp4xx/hardware.h | 1 +
- include/asm-arm/arch-ixp4xx/irqs.h | 7 +
- 8 files changed, 421 insertions(+), 4 deletions(-)
- create mode 100644 arch/arm/mach-ixp4xx/fsg-pci.c
- create mode 100644 arch/arm/mach-ixp4xx/fsg-setup.c
- create mode 100644 include/asm-arm/arch-ixp4xx/fsg.h
-
--- a/arch/arm/configs/ixp4xx_defconfig
+++ b/arch/arm/configs/ixp4xx_defconfig
@@ -165,6 +165,7 @@
diff --git a/target/linux/ixp4xx/patches-2.6.26/100-gateway7001_mac_plat_info.patch b/target/linux/ixp4xx/patches-2.6.26/100-gateway7001_mac_plat_info.patch
deleted file mode 100644
index a2ebb1a83..000000000
--- a/target/linux/ixp4xx/patches-2.6.26/100-gateway7001_mac_plat_info.patch
+++ /dev/null
@@ -1,40 +0,0 @@
---- a/arch/arm/mach-ixp4xx/gateway7001-setup.c
-+++ b/arch/arm/mach-ixp4xx/gateway7001-setup.c
-@@ -76,9 +76,36 @@
- .resource = &gateway7001_uart_resource,
- };
-
-+/* Built-in 10/100 Ethernet MAC interfaces */
-+static struct eth_plat_info gateway7001_plat_eth[] = {
-+ {
-+ .phy = 1,
-+ .rxq = 3,
-+ .txreadyq = 20,
-+ }, {
-+ .phy = 2,
-+ .rxq = 4,
-+ .txreadyq = 21,
-+ }
-+};
-+
-+static struct platform_device gateway7001_eth[] = {
-+ {
-+ .name = "ixp4xx_eth",
-+ .id = IXP4XX_ETH_NPEB,
-+ .dev.platform_data = gateway7001_plat_eth,
-+ }, {
-+ .name = "ixp4xx_eth",
-+ .id = IXP4XX_ETH_NPEC,
-+ .dev.platform_data = gateway7001_plat_eth + 1,
-+ }
-+};
-+
- static struct platform_device *gateway7001_devices[] __initdata = {
- &gateway7001_flash,
-- &gateway7001_uart
-+ &gateway7001_uart,
-+ &gateway7001_eth[0],
-+ &gateway7001_eth[1],
- };
-
- static void __init gateway7001_init(void)
diff --git a/target/linux/ixp4xx/patches-2.6.26/100-wg302v2_gateway7001_mac_plat_info.patch b/target/linux/ixp4xx/patches-2.6.26/100-wg302v2_gateway7001_mac_plat_info.patch
new file mode 100644
index 000000000..bbdd00c80
--- /dev/null
+++ b/target/linux/ixp4xx/patches-2.6.26/100-wg302v2_gateway7001_mac_plat_info.patch
@@ -0,0 +1,68 @@
+--- a/arch/arm/mach-ixp4xx/gateway7001-setup.c
++++ b/arch/arm/mach-ixp4xx/gateway7001-setup.c
+@@ -76,9 +76,35 @@
+ .resource = &gateway7001_uart_resource,
+ };
+
++static struct eth_plat_info gateway7001_plat_eth[] = {
++ {
++ .phy = 1,
++ .rxq = 3,
++ .txreadyq = 20,
++ }, {
++ .phy = 2,
++ .rxq = 4,
++ .txreadyq = 21,
++ }
++};
++
++static struct platform_device gateway7001_eth[] = {
++ {
++ .name = "ixp4xx_eth",
++ .id = IXP4XX_ETH_NPEB,
++ .dev.platform_data = gateway7001_plat_eth,
++ }, {
++ .name = "ixp4xx_eth",
++ .id = IXP4XX_ETH_NPEC,
++ .dev.platform_data = gateway7001_plat_eth + 1,
++ }
++};
++
+ static struct platform_device *gateway7001_devices[] __initdata = {
+ &gateway7001_flash,
+- &gateway7001_uart
++ &gateway7001_uart,
++ &gateway7001_eth[0],
++ &gateway7001_eth[1],
+ };
+
+ static void __init gateway7001_init(void)
+--- a/arch/arm/mach-ixp4xx/wg302v2-setup.c
++++ b/arch/arm/mach-ixp4xx/wg302v2-setup.c
+@@ -77,9 +77,26 @@
+ .resource = &wg302v2_uart_resource,
+ };
+
++static struct eth_plat_info wg302v2_plat_eth[] = {
++ {
++ .phy = 8,
++ .rxq = 3,
++ .txreadyq = 20,
++ }
++};
++
++static struct platform_device wg302v2_eth[] = {
++ {
++ .name = "ixp4xx_eth",
++ .id = IXP4XX_ETH_NPEB,
++ .dev.platform_data = wg302v2_plat_eth,
++ }
++};
++
+ static struct platform_device *wg302v2_devices[] __initdata = {
+ &wg302v2_flash,
+ &wg302v2_uart,
++ &wg302v2_eth[0],
+ };
+
+ static void __init wg302v2_init(void)
diff --git a/target/linux/ixp4xx/patches-2.6.26/101-wg302_mac_plat_info.patch b/target/linux/ixp4xx/patches-2.6.26/101-wg302_mac_plat_info.patch
deleted file mode 100644
index 850947fc8..000000000
--- a/target/linux/ixp4xx/patches-2.6.26/101-wg302_mac_plat_info.patch
+++ /dev/null
@@ -1,30 +0,0 @@
---- a/arch/arm/mach-ixp4xx/wg302v2-setup.c
-+++ b/arch/arm/mach-ixp4xx/wg302v2-setup.c
-@@ -77,9 +77,27 @@
- .resource = &wg302v2_uart_resource,
- };
-
-+/* Built-in 10/100 Ethernet MAC interfaces */
-+static struct eth_plat_info wg302_plat_eth[] = {
-+ {
-+ .phy = 8,
-+ .rxq = 3,
-+ .txreadyq = 20,
-+ }
-+};
-+
-+static struct platform_device wg302_eth[] = {
-+ {
-+ .name = "ixp4xx_eth",
-+ .id = IXP4XX_ETH_NPEB,
-+ .dev.platform_data = wg302_plat_eth,
-+ }
-+};
-+
- static struct platform_device *wg302v2_devices[] __initdata = {
- &wg302v2_flash,
- &wg302v2_uart,
-+ &wg302_eth[0],
- };
-
- static void __init wg302v2_init(void)
diff --git a/target/linux/ixp4xx/patches-2.6.26/160-wg302v1_support.patch b/target/linux/ixp4xx/patches-2.6.26/105-wg302v1_support.patch
index a5a6e5ca9..102342322 100644
--- a/target/linux/ixp4xx/patches-2.6.26/160-wg302v1_support.patch
+++ b/target/linux/ixp4xx/patches-2.6.26/105-wg302v1_support.patch
@@ -1,3 +1,13 @@
+--- a/arch/arm/configs/ixp4xx_defconfig
++++ b/arch/arm/configs/ixp4xx_defconfig
+@@ -155,6 +155,7 @@
+ CONFIG_MACH_LOFT=y
+ CONFIG_ARCH_ADI_COYOTE=y
+ CONFIG_MACH_GATEWAY7001=y
++CONFIG_MACH_WG302V1=y
+ CONFIG_MACH_WG302V2=y
+ CONFIG_ARCH_IXDP425=y
+ CONFIG_MACH_IXDPG425=y
--- a/arch/arm/mach-ixp4xx/Kconfig
+++ b/arch/arm/mach-ixp4xx/Kconfig
@@ -49,6 +49,14 @@
@@ -24,18 +34,18 @@
+obj-pci-$(CONFIG_MACH_WG302V1) += wg302v1-pci.o
obj-pci-$(CONFIG_MACH_WG302V2) += wg302v2-pci.o
obj-pci-$(CONFIG_MACH_FSG) += fsg-pci.o
- obj-pci-$(CONFIG_MACH_PRONGHORNMETRO) += pronghornmetro-pci.o
-@@ -33,6 +34,7 @@
+
+@@ -28,6 +29,7 @@
obj-$(CONFIG_MACH_NAS100D) += nas100d-setup.o
obj-$(CONFIG_MACH_DSMG600) += dsmg600-setup.o
obj-$(CONFIG_MACH_GATEWAY7001) += gateway7001-setup.o
+obj-$(CONFIG_MACH_WG302V1) += wg302v1-setup.o
obj-$(CONFIG_MACH_WG302V2) += wg302v2-setup.o
obj-$(CONFIG_MACH_FSG) += fsg-setup.o
- obj-$(CONFIG_MACH_PRONGHORNMETRO) += pronghornmetro-setup.o
+
--- /dev/null
+++ b/arch/arm/mach-ixp4xx/wg302v1-pci.c
-@@ -0,0 +1,63 @@
+@@ -0,0 +1,64 @@
+/*
+ * arch/arch/mach-ixp4xx/wg302v1-pci.c
+ *
@@ -79,7 +89,8 @@
+ return IRQ_IXP4XX_GPIO8;
+ else if (slot == 2)
+ return IRQ_IXP4XX_GPIO10;
-+ else return -1;
++ else
++ return -1;
+}
+
+struct hw_pci wg302v1_pci __initdata = {
@@ -101,7 +112,7 @@
+subsys_initcall(wg302v1_pci_init);
--- /dev/null
+++ b/arch/arm/mach-ixp4xx/wg302v1-setup.c
-@@ -0,0 +1,109 @@
+@@ -0,0 +1,126 @@
+/*
+ * arch/arm/mach-ixp4xx/wg302v1-setup.c
+ *
@@ -123,10 +134,10 @@
+#include <linux/tty.h>
+#include <linux/serial_8250.h>
+#include <linux/slab.h>
++#include <linux/types.h>
++#include <linux/memory.h>
+
-+#include <asm/types.h>
+#include <asm/setup.h>
-+#include <asm/memory.h>
+#include <asm/hardware.h>
+#include <asm/irq.h>
+#include <asm/mach-types.h>
@@ -181,9 +192,26 @@
+ .resource = &wg302v1_uart_resource,
+};
+
++static struct eth_plat_info wg302v1_plat_eth[] = {
++ {
++ .phy = 30,
++ .rxq = 3,
++ .txreadyq = 20,
++ }
++};
++
++static struct platform_device wg302v1_eth[] = {
++ {
++ .name = "ixp4xx_eth",
++ .id = IXP4XX_ETH_NPEB,
++ .dev.platform_data = wg302v1_plat_eth,
++ }
++};
++
+static struct platform_device *wg302v1_devices[] __initdata = {
+ &wg302v1_flash,
+ &wg302v1_uart,
++ &wg302v1_eth[0],
+};
+
+static void __init wg302v1_init(void)
diff --git a/target/linux/ixp4xx/patches-2.6.26/110-pronghorn_metro_support.patch b/target/linux/ixp4xx/patches-2.6.26/110-pronghorn_metro_support.patch
index 6908a28ad..a35663a9b 100644
--- a/target/linux/ixp4xx/patches-2.6.26/110-pronghorn_metro_support.patch
+++ b/target/linux/ixp4xx/patches-2.6.26/110-pronghorn_metro_support.patch
@@ -1,47 +1,68 @@
+--- a/arch/arm/configs/ixp4xx_defconfig
++++ b/arch/arm/configs/ixp4xx_defconfig
+@@ -157,6 +157,8 @@
+ CONFIG_MACH_GATEWAY7001=y
+ CONFIG_MACH_WG302V1=y
+ CONFIG_MACH_WG302V2=y
++CONFIG_MACH_PRONGHORN=y
++CONFIG_MACH_PRONGHORNMETRO=y
+ CONFIG_ARCH_IXDP425=y
+ CONFIG_MACH_IXDPG425=y
+ CONFIG_MACH_IXDP465=y
--- a/arch/arm/mach-ixp4xx/Kconfig
+++ b/arch/arm/mach-ixp4xx/Kconfig
-@@ -57,6 +57,14 @@
+@@ -65,6 +65,24 @@
WG302 v2 or WAG302 v2 Access Points. For more information
on this platform, see http://openwrt.org
-+config MACH_PRONGHORNMETRO
-+ bool "Pronghorn Metro"
++config MACH_PRONGHORN
++ bool "ADI Pronghorn series"
+ select PCI
+ help
+ Say 'Y' here if you want your kernel to support the ADI
-+ Engineering Pronghorn Metro Platform. For more
-+ information on this platform, see <file:Documentation/arm/IXP4xx>.
++ Engineering Pronghorn series. For more
++ information on this platform, see http://www.adiengineering.com
++
++#
++# There're only minimal differences kernel-wise between the Pronghorn and
++# Pronghorn Metro boards - they use different chip selects to drive the
++# CF slot connected to the expansion bus, so we just enable them together.
++#
++config MACH_PRONGHORNMETRO
++ bool
++ depends on MACH_PRONGHORN
++ default y
+
config ARCH_IXDP425
bool "IXDP425"
help
--- a/arch/arm/mach-ixp4xx/Makefile
+++ b/arch/arm/mach-ixp4xx/Makefile
-@@ -16,6 +16,7 @@
- obj-pci-$(CONFIG_MACH_GATEWAY7001) += gateway7001-pci.o
+@@ -17,6 +17,7 @@
+ obj-pci-$(CONFIG_MACH_WG302V1) += wg302v1-pci.o
obj-pci-$(CONFIG_MACH_WG302V2) += wg302v2-pci.o
obj-pci-$(CONFIG_MACH_FSG) += fsg-pci.o
-+obj-pci-$(CONFIG_MACH_PRONGHORNMETRO) += pronghornmetro-pci.o
++obj-pci-$(CONFIG_MACH_PRONGHORN) += pronghorn-pci.o
obj-y += common.o
-@@ -30,6 +31,7 @@
- obj-$(CONFIG_MACH_GATEWAY7001) += gateway7001-setup.o
+@@ -32,6 +33,7 @@
+ obj-$(CONFIG_MACH_WG302V1) += wg302v1-setup.o
obj-$(CONFIG_MACH_WG302V2) += wg302v2-setup.o
obj-$(CONFIG_MACH_FSG) += fsg-setup.o
-+obj-$(CONFIG_MACH_PRONGHORNMETRO) += pronghornmetro-setup.o
++obj-$(CONFIG_MACH_PRONGHORN) += pronghorn-setup.o
obj-$(CONFIG_PCI) += $(obj-pci-$(CONFIG_PCI)) common-pci.o
obj-$(CONFIG_IXP4XX_QMGR) += ixp4xx_qmgr.o
--- /dev/null
-+++ b/arch/arm/mach-ixp4xx/pronghornmetro-pci.c
-@@ -0,0 +1,74 @@
++++ b/arch/arm/mach-ixp4xx/pronghorn-pci.c
+@@ -0,0 +1,70 @@
+/*
-+ * arch/arch/mach-ixp4xx/pronghornmetro-pci.c
++ * arch/arch/mach-ixp4xx/pronghorn-pci.c
+ *
-+ * PCI setup routines for ADI Engineering Pronghorn Metro
++ * PCI setup routines for ADI Engineering Pronghorn series
+ *
-+ * Copyright (C) 2007 Imre Kaloz <kaloz@openwrt.org>
++ * Copyright (C) 2008 Imre Kaloz <kaloz@openwrt.org>
+ *
+ * based on coyote-pci.c:
+ * Copyright (C) 2002 Jungo Software Technologies.
@@ -62,15 +83,10 @@
+
+#include <asm/mach-types.h>
+#include <asm/hardware.h>
-+#include <asm/irq.h>
+
+#include <asm/mach/pci.h>
+
-+extern void ixp4xx_pci_preinit(void);
-+extern int ixp4xx_setup(int nr, struct pci_sys_data *sys);
-+extern struct pci_bus *ixp4xx_scan_bus(int nr, struct pci_sys_data *sys);
-+
-+void __init pronghornmetro_pci_preinit(void)
++void __init pronghorn_pci_preinit(void)
+{
+ set_irq_type(IRQ_IXP4XX_GPIO4, IRQT_LOW);
+ set_irq_type(IRQ_IXP4XX_GPIO6, IRQT_LOW);
@@ -80,7 +96,7 @@
+ ixp4xx_pci_preinit();
+}
+
-+static int __init pronghornmetro_map_irq(struct pci_dev *dev, u8 slot, u8 pin)
++static int __init pronghorn_map_irq(struct pci_dev *dev, u8 slot, u8 pin)
+{
+ if (slot == 13)
+ return IRQ_IXP4XX_GPIO4;
@@ -90,35 +106,36 @@
+ return IRQ_IXP4XX_GPIO11;
+ else if (slot == 16)
+ return IRQ_IXP4XX_GPIO1;
-+ else return -1;
++ else
++ return -1;
+}
+
-+struct hw_pci pronghornmetro_pci __initdata = {
-+ .nr_controllers = 1,
-+ .preinit = pronghornmetro_pci_preinit,
-+ .swizzle = pci_std_swizzle,
-+ .setup = ixp4xx_setup,
-+ .scan = ixp4xx_scan_bus,
-+ .map_irq = pronghornmetro_map_irq,
++struct hw_pci pronghorn_pci __initdata = {
++ .nr_controllers = 1,
++ .preinit = pronghorn_pci_preinit,
++ .swizzle = pci_std_swizzle,
++ .setup = ixp4xx_setup,
++ .scan = ixp4xx_scan_bus,
++ .map_irq = pronghorn_map_irq,
+};
+
-+int __init pronghornmetro_pci_init(void)
++int __init pronghorn_pci_init(void)
+{
-+ if (machine_is_pronghorn_metro())
-+ pci_common_init(&pronghornmetro_pci);
++ if (machine_is_pronghorn() || machine_is_pronghorn_metro())
++ pci_common_init(&pronghorn_pci);
+ return 0;
+}
+
-+subsys_initcall(pronghornmetro_pci_init);
++subsys_initcall(pronghorn_pci_init);
--- /dev/null
-+++ b/arch/arm/mach-ixp4xx/pronghornmetro-setup.c
-@@ -0,0 +1,147 @@
++++ b/arch/arm/mach-ixp4xx/pronghorn-setup.c
+@@ -0,0 +1,245 @@
+/*
-+ * arch/arm/mach-ixp4xx/pronghornmetro-setup.c
++ * arch/arm/mach-ixp4xx/pronghorn-setup.c
+ *
-+ * Board setup for the ADI Engineering Pronghorn Metro
++ * Board setup for the ADI Engineering Pronghorn series
+ *
-+ * Copyright (C) 2007 Imre Kaloz <Kaloz@openwrt.org>
++ * Copyright (C) 2008 Imre Kaloz <Kaloz@openwrt.org>
+ *
+ * based on coyote-setup.c:
+ * Copyright (C) 2003-2005 MontaVista Software, Inc.
@@ -133,42 +150,59 @@
+#include <linux/tty.h>
+#include <linux/serial_8250.h>
+#include <linux/slab.h>
++#include <linux/types.h>
++#include <linux/memory.h>
++#include <linux/i2c-gpio.h>
+
-+#include <asm/types.h>
+#include <asm/setup.h>
-+#include <asm/memory.h>
+#include <asm/hardware.h>
+#include <asm/irq.h>
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/flash.h>
+
-+static struct flash_platform_data pronghornmetro_flash_data = {
++static struct flash_platform_data pronghorn_flash_data = {
+ .map_name = "cfi_probe",
+ .width = 2,
+};
+
-+static struct resource pronghornmetro_flash_resource = {
++static struct resource pronghorn_flash_resource = {
+ .flags = IORESOURCE_MEM,
+};
+
-+static struct platform_device pronghornmetro_flash = {
++static struct platform_device pronghorn_flash = {
+ .name = "IXP4XX-Flash",
+ .id = 0,
+ .dev = {
-+ .platform_data = &pronghornmetro_flash_data,
++ .platform_data = &pronghorn_flash_data,
+ },
+ .num_resources = 1,
-+ .resource = &pronghornmetro_flash_resource,
++ .resource = &pronghorn_flash_resource,
+};
+
-+static struct resource pronghornmetro_uart_resource = {
-+ .start = IXP4XX_UART2_BASE_PHYS,
-+ .end = IXP4XX_UART2_BASE_PHYS + 0x0fff,
-+ .flags = IORESOURCE_MEM,
++static struct resource pronghorn_uart_resources [] = {
++ {
++ .start = IXP4XX_UART1_BASE_PHYS,
++ .end = IXP4XX_UART1_BASE_PHYS + 0x0fff,
++ .flags = IORESOURCE_MEM
++ },
++ {
++ .start = IXP4XX_UART2_BASE_PHYS,
++ .end = IXP4XX_UART2_BASE_PHYS + 0x0fff,
++ .flags = IORESOURCE_MEM
++ }
+};
+
-+static struct plat_serial8250_port pronghornmetro_uart_data[] = {
++static struct plat_serial8250_port pronghorn_uart_data[] = {
++ {
++ .mapbase = IXP4XX_UART1_BASE_PHYS,
++ .membase = (char *)IXP4XX_UART1_BASE_VIRT + REG_OFFSET,
++ .irq = IRQ_IXP4XX_UART1,
++ .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
++ .iotype = UPIO_MEM,
++ .regshift = 2,
++ .uartclk = IXP4XX_UART_XTAL,
++ },
+ {
+ .mapbase = IXP4XX_UART2_BASE_PHYS,
+ .membase = (char *)IXP4XX_UART2_BASE_VIRT + REG_OFFSET,
@@ -181,17 +215,49 @@
+ { },
+};
+
-+static struct platform_device pronghornmetro_uart = {
++static struct platform_device pronghorn_uart = {
+ .name = "serial8250",
+ .id = PLAT8250_DEV_PLATFORM,
-+ .dev = {
-+ .platform_data = pronghornmetro_uart_data,
++ .dev = {
++ .platform_data = pronghorn_uart_data,
+ },
-+ .num_resources = 1,
-+ .resource = &pronghornmetro_uart_resource,
++ .num_resources = 2,
++ .resource = pronghorn_uart_resources,
++};
++
++static struct i2c_gpio_platform_data pronghorn_i2c_gpio_data = {
++ .sda_pin = 9,
++ .scl_pin = 10,
++};
++
++static struct platform_device pronghorn_i2c_gpio = {
++ .name = "i2c-gpio",
++ .id = 0,
++ .dev = {
++ .platform_data = &pronghorn_i2c_gpio_data,
++ },
++};
++
++static struct gpio_led pronghorn_led_pin[] = {
++ {
++ .name = "pronghorn:green:status",
++ .gpio = 7,
++ },
++ { },
++};
++
++static struct gpio_led_platform_data pronghorn_led_data = {
++ .num_leds = ARRAY_SIZE(pronghorn_led_pin),
++ .leds = pronghorn_led_pin,
+};
+
-+static struct resource pronghornmetro_pata_resources[] = {
++static struct platform_device pronghorn_led = {
++ .name = "leds-gpio",
++ .id = -1,
++ .dev.platform_data = &pronghorn_led_data,
++};
++
++static struct resource pronghorn_pata_resources[] = {
+ {
+ .flags = IORESOURCE_MEM
+ },
@@ -206,50 +272,89 @@
+ },
+};
+
-+static struct ixp4xx_pata_data pronghornmetro_pata_data = {
++static struct ixp4xx_pata_data pronghorn_pata_data = {
+ .cs0_bits = 0xbfff0043,
+ .cs1_bits = 0xbfff0043,
+};
+
-+static struct platform_device pronghornmetro_pata = {
++static struct platform_device pronghorn_pata = {
+ .name = "pata_ixp4xx_cf",
+ .id = 0,
-+ .dev.platform_data = &pronghornmetro_pata_data,
-+ .num_resources = ARRAY_SIZE(pronghornmetro_pata_resources),
-+ .resource = pronghornmetro_pata_resources,
++ .dev.platform_data = &pronghorn_pata_data,
++ .num_resources = ARRAY_SIZE(pronghorn_pata_resources),
++ .resource = pronghorn_pata_resources,
+};
+
-+static struct platform_device *pronghornmetro_devices[] __initdata = {
-+ &pronghornmetro_flash,
-+ &pronghornmetro_uart,
++static struct eth_plat_info pronghorn_plat_eth[] = {
++ {
++ .phy = 0,
++ .rxq = 3,
++ .txreadyq = 20,
++ }, {
++ .phy = 1,
++ .rxq = 4,
++ .txreadyq = 21,
++ }
+};
+
-+static void __init pronghornmetro_init(void)
++static struct platform_device pronghorn_eth[] = {
++ {
++ .name = "ixp4xx_eth",
++ .id = IXP4XX_ETH_NPEB,
++ .dev.platform_data = pronghorn_plat_eth,
++ }, {
++ .name = "ixp4xx_eth",
++ .id = IXP4XX_ETH_NPEC,
++ .dev.platform_data = pronghorn_plat_eth + 1,
++ }
++};
++
++static struct platform_device *pronghorn_devices[] __initdata = {
++ &pronghorn_flash,
++ &pronghorn_uart,
++ &pronghorn_led,
++ &pronghorn_eth[0],
++ &pronghorn_eth[1],
++};
++
++static void __init pronghorn_init(void)
+{
+ ixp4xx_sys_init();
+
-+ pronghornmetro_flash_resource.start = IXP4XX_EXP_BUS_BASE(0);
-+ pronghornmetro_flash_resource.end = IXP4XX_EXP_BUS_BASE(0) + SZ_16M - 1;
++ pronghorn_flash_resource.start = IXP4XX_EXP_BUS_BASE(0);
++ pronghorn_flash_resource.end = IXP4XX_EXP_BUS_BASE(0) + SZ_16M - 1;
+
+ *IXP4XX_EXP_CS0 |= IXP4XX_FLASH_WRITABLE;
+ *IXP4XX_EXP_CS1 = *IXP4XX_EXP_CS0;
+
-+ platform_add_devices(pronghornmetro_devices, ARRAY_SIZE(pronghornmetro_devices));
++ platform_add_devices(pronghorn_devices, ARRAY_SIZE(pronghorn_devices));
++
++ if (machine_is_pronghorn()) {
++ pronghorn_pata_resources[0].start = IXP4XX_EXP_BUS_BASE(3);
++ pronghorn_pata_resources[0].end = IXP4XX_EXP_BUS_END(3);
++
++ pronghorn_pata_resources[1].start = IXP4XX_EXP_BUS_BASE(4);
++ pronghorn_pata_resources[1].end = IXP4XX_EXP_BUS_END(4);
+
-+ pronghornmetro_pata_resources[0].start = IXP4XX_EXP_BUS_BASE(1);
-+ pronghornmetro_pata_resources[0].end = IXP4XX_EXP_BUS_END(1);
++ pronghorn_pata_data.cs0_cfg = IXP4XX_EXP_CS3;
++ pronghorn_pata_data.cs1_cfg = IXP4XX_EXP_CS4;
++ } else {
++ pronghorn_pata_resources[0].start = IXP4XX_EXP_BUS_BASE(2);
++ pronghorn_pata_resources[0].end = IXP4XX_EXP_BUS_END(2);
+
-+ pronghornmetro_pata_resources[1].start = IXP4XX_EXP_BUS_BASE(2);
-+ pronghornmetro_pata_resources[1].end = IXP4XX_EXP_BUS_END(2);
++ pronghorn_pata_resources[1].start = IXP4XX_EXP_BUS_BASE(3);
++ pronghorn_pata_resources[1].end = IXP4XX_EXP_BUS_END(3);
+
-+ pronghornmetro_pata_data.cs0_cfg = IXP4XX_EXP_CS1;
-+ pronghornmetro_pata_data.cs1_cfg = IXP4XX_EXP_CS2;
++ pronghorn_pata_data.cs0_cfg = IXP4XX_EXP_CS2;
++ pronghorn_pata_data.cs1_cfg = IXP4XX_EXP_CS3;
+
-+ platform_device_register(&pronghornmetro_pata);
++ platform_device_register(&pronghorn_i2c_gpio);
++ }
++
++ platform_device_register(&pronghorn_pata);
+}
+
-+#ifdef CONFIG_MACH_PRONGHORNMETRO
-+MACHINE_START(PRONGHORNMETRO, "ADI Engineering Pronghorn Metro")
++MACHINE_START(PRONGHORN, "ADI Engineering Pronghorn")
+ /* Maintainer: Imre Kaloz <kaloz@openwrt.org> */
+ .phys_io = IXP4XX_PERIPHERAL_BASE_PHYS,
+ .io_pg_offst = ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xfffc,
@@ -257,21 +362,19 @@
+ .init_irq = ixp4xx_init_irq,
+ .timer = &ixp4xx_timer,
+ .boot_params = 0x0100,
-+ .init_machine = pronghornmetro_init,
++ .init_machine = pronghorn_init,
+MACHINE_END
-+#endif
---- a/Documentation/arm/IXP4xx
-+++ b/Documentation/arm/IXP4xx
-@@ -111,6 +111,9 @@
- the platform has two mini-PCI slots used for 802.11[bga] cards.
- Finally, there is an IDE port hanging off the expansion bus.
-
-+ADI Engineering Pronghorn Metro Platform
-+http://www.adiengineering.com/php-bin/ecomm4/productDisplay.php?category_id=30&product_id=85
+
- Gateworks Avila Network Platform
- http://www.gateworks.com/avila_sbc.htm
-
++MACHINE_START(PRONGHORNMETRO, "ADI Engineering Pronghorn Metro")
++ /* Maintainer: Imre Kaloz <kaloz@openwrt.org> */
++ .phys_io = IXP4XX_PERIPHERAL_BASE_PHYS,
++ .io_pg_offst = ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xfffc,
++ .map_io = ixp4xx_map_io,
++ .init_irq = ixp4xx_init_irq,
++ .timer = &ixp4xx_timer,
++ .boot_params = 0x0100,
++ .init_machine = pronghorn_init,
++MACHINE_END
--- a/include/asm-arm/arch-ixp4xx/uncompress.h
+++ b/include/asm-arm/arch-ixp4xx/uncompress.h
@@ -41,7 +41,8 @@
@@ -280,7 +383,7 @@
if (machine_is_adi_coyote() || machine_is_gtwx5715() ||
- machine_is_gateway7001() || machine_is_wg302v2())
+ machine_is_gateway7001() || machine_is_wg302v2() ||
-+ machine_is_pronghorn_metro())
++ machine_is_pronghorn() || machine_is_pronghorn_metro())
uart_base = (volatile u32*) IXP4XX_UART2_BASE_PHYS;
else
uart_base = (volatile u32*) IXP4XX_UART1_BASE_PHYS;
diff --git a/target/linux/ixp4xx/patches-2.6.26/111-pronghorn_metro_mac_plat_info.patch b/target/linux/ixp4xx/patches-2.6.26/111-pronghorn_metro_mac_plat_info.patch
deleted file mode 100644
index 3450b5b02..000000000
--- a/target/linux/ixp4xx/patches-2.6.26/111-pronghorn_metro_mac_plat_info.patch
+++ /dev/null
@@ -1,39 +0,0 @@
---- a/arch/arm/mach-ixp4xx/pronghornmetro-setup.c
-+++ b/arch/arm/mach-ixp4xx/pronghornmetro-setup.c
-@@ -104,9 +104,36 @@
- .resource = pronghornmetro_pata_resources,
- };
-
-+/* Built-in 10/100 Ethernet MAC interfaces */
-+static struct eth_plat_info pronghornmetro_plat_eth[] = {
-+ {
-+ .phy = 0,
-+ .rxq = 3,
-+ .txreadyq = 20,
-+ }, {
-+ .phy = 1,
-+ .rxq = 4,
-+ .txreadyq = 21,
-+ }
-+};
-+
-+static struct platform_device pronghornmetro_eth[] = {
-+ {
-+ .name = "ixp4xx_eth",
-+ .id = IXP4XX_ETH_NPEB,
-+ .dev.platform_data = pronghornmetro_plat_eth,
-+ }, {
-+ .name = "ixp4xx_eth",
-+ .id = IXP4XX_ETH_NPEC,
-+ .dev.platform_data = pronghornmetro_plat_eth + 1,
-+ }
-+};
-+
- static struct platform_device *pronghornmetro_devices[] __initdata = {
- &pronghornmetro_flash,
- &pronghornmetro_uart,
-+ &pronghornmetro_eth[0],
-+ &pronghornmetro_eth[1],
- };
-
- static void __init pronghornmetro_init(void)
diff --git a/target/linux/ixp4xx/patches-2.6.26/120-compex_support.patch b/target/linux/ixp4xx/patches-2.6.26/120-compex_support.patch
index 689d7a3c7..9f309a6fa 100644
--- a/target/linux/ixp4xx/patches-2.6.26/120-compex_support.patch
+++ b/target/linux/ixp4xx/patches-2.6.26/120-compex_support.patch
@@ -1,8 +1,8 @@
--- a/arch/arm/mach-ixp4xx/Kconfig
+++ b/arch/arm/mach-ixp4xx/Kconfig
-@@ -65,6 +65,14 @@
- Engineering Pronghorn Metro Platform. For more
- information on this platform, see <file:Documentation/arm/IXP4xx>.
+@@ -83,6 +83,14 @@
+ depends on MACH_PRONGHORN
+ default y
+config MACH_COMPEX
+ bool "Compex WP18 / NP18A"
@@ -17,18 +17,18 @@
help
--- a/arch/arm/mach-ixp4xx/Makefile
+++ b/arch/arm/mach-ixp4xx/Makefile
-@@ -17,6 +17,7 @@
+@@ -18,6 +18,7 @@
obj-pci-$(CONFIG_MACH_WG302V2) += wg302v2-pci.o
obj-pci-$(CONFIG_MACH_FSG) += fsg-pci.o
- obj-pci-$(CONFIG_MACH_PRONGHORNMETRO) += pronghornmetro-pci.o
+ obj-pci-$(CONFIG_MACH_PRONGHORN) += pronghorn-pci.o
+obj-pci-$(CONFIG_MACH_COMPEX) += ixdp425-pci.o
obj-y += common.o
-@@ -32,6 +33,7 @@
+@@ -34,6 +35,7 @@
obj-$(CONFIG_MACH_WG302V2) += wg302v2-setup.o
obj-$(CONFIG_MACH_FSG) += fsg-setup.o
- obj-$(CONFIG_MACH_PRONGHORNMETRO) += pronghornmetro-setup.o
+ obj-$(CONFIG_MACH_PRONGHORN) += pronghorn-setup.o
+obj-$(CONFIG_MACH_COMPEX) += compex-setup.o
obj-$(CONFIG_PCI) += $(obj-pci-$(CONFIG_PCI)) common-pci.o
diff --git a/target/linux/ixp4xx/patches-2.6.26/130-wrt300nv2_support.patch b/target/linux/ixp4xx/patches-2.6.26/130-wrt300nv2_support.patch
index b797cb425..29c86390e 100644
--- a/target/linux/ixp4xx/patches-2.6.26/130-wrt300nv2_support.patch
+++ b/target/linux/ixp4xx/patches-2.6.26/130-wrt300nv2_support.patch
@@ -1,6 +1,6 @@
--- a/arch/arm/mach-ixp4xx/Kconfig
+++ b/arch/arm/mach-ixp4xx/Kconfig
-@@ -73,6 +73,14 @@
+@@ -91,6 +91,14 @@
WP18 or NP18A boards. For more information on this
platform, see http://openwrt.org
@@ -17,17 +17,17 @@
help
--- a/arch/arm/mach-ixp4xx/Makefile
+++ b/arch/arm/mach-ixp4xx/Makefile
-@@ -18,6 +18,7 @@
+@@ -19,6 +19,7 @@
obj-pci-$(CONFIG_MACH_FSG) += fsg-pci.o
- obj-pci-$(CONFIG_MACH_PRONGHORNMETRO) += pronghornmetro-pci.o
+ obj-pci-$(CONFIG_MACH_PRONGHORN) += pronghorn-pci.o
obj-pci-$(CONFIG_MACH_COMPEX) += ixdp425-pci.o
+obj-pci-$(CONFIG_MACH_WRT300NV2) += wrt300nv2-pci.o
obj-y += common.o
-@@ -34,6 +35,7 @@
+@@ -36,6 +37,7 @@
obj-$(CONFIG_MACH_FSG) += fsg-setup.o
- obj-$(CONFIG_MACH_PRONGHORNMETRO) += pronghornmetro-setup.o
+ obj-$(CONFIG_MACH_PRONGHORN) += pronghorn-setup.o
obj-$(CONFIG_MACH_COMPEX) += compex-setup.o
+obj-$(CONFIG_MACH_WRT300NV2) += wrt300nv2-setup.o
@@ -218,8 +218,8 @@
*/
if (machine_is_adi_coyote() || machine_is_gtwx5715() ||
machine_is_gateway7001() || machine_is_wg302v2() ||
-- machine_is_pronghorn_metro())
-+ machine_is_pronghorn_metro() || machine_is_wrt300nv2())
+- machine_is_pronghorn() || machine_is_pronghorn_metro())
++ machine_is_pronghorn() || machine_is_pronghorn_metro() || machine_is_wrt300nv2())
uart_base = (volatile u32*) IXP4XX_UART2_BASE_PHYS;
else
uart_base = (volatile u32*) IXP4XX_UART1_BASE_PHYS;
diff --git a/target/linux/ixp4xx/patches-2.6.26/140-sidewinder_support.patch b/target/linux/ixp4xx/patches-2.6.26/140-sidewinder_support.patch
index 50f6e2752..e3f450fdb 100644
--- a/target/linux/ixp4xx/patches-2.6.26/140-sidewinder_support.patch
+++ b/target/linux/ixp4xx/patches-2.6.26/140-sidewinder_support.patch
@@ -1,8 +1,8 @@
--- a/arch/arm/mach-ixp4xx/Kconfig
+++ b/arch/arm/mach-ixp4xx/Kconfig
-@@ -65,6 +65,14 @@
- Engineering Pronghorn Metro Platform. For more
- information on this platform, see <file:Documentation/arm/IXP4xx>.
+@@ -83,6 +83,14 @@
+ depends on MACH_PRONGHORN
+ default y
+config MACH_SIDEWINDER
+ bool "Sidewinder"
@@ -15,7 +15,7 @@
config MACH_COMPEX
bool "Compex WP18 / NP18A"
select PCI
-@@ -163,7 +171,7 @@
+@@ -181,7 +189,7 @@
#
config CPU_IXP46X
bool
@@ -26,16 +26,16 @@
config CPU_IXP43X
--- a/arch/arm/mach-ixp4xx/Makefile
+++ b/arch/arm/mach-ixp4xx/Makefile
-@@ -19,6 +19,7 @@
- obj-pci-$(CONFIG_MACH_PRONGHORNMETRO) += pronghornmetro-pci.o
+@@ -20,6 +20,7 @@
+ obj-pci-$(CONFIG_MACH_PRONGHORN) += pronghorn-pci.o
obj-pci-$(CONFIG_MACH_COMPEX) += ixdp425-pci.o
obj-pci-$(CONFIG_MACH_WRT300NV2) += wrt300nv2-pci.o
+obj-pci-$(CONFIG_MACH_SIDEWINDER) += sidewinder-pci.o
obj-y += common.o
-@@ -36,6 +37,7 @@
- obj-$(CONFIG_MACH_PRONGHORNMETRO) += pronghornmetro-setup.o
+@@ -38,6 +39,7 @@
+ obj-$(CONFIG_MACH_PRONGHORN) += pronghorn-setup.o
obj-$(CONFIG_MACH_COMPEX) += compex-setup.o
obj-$(CONFIG_MACH_WRT300NV2) += wrt300nv2-setup.o
+obj-$(CONFIG_MACH_SIDEWINDER) += sidewinder-setup.o
diff --git a/target/linux/ixp4xx/patches-2.6.26/150-lanready_ap1000_support.patch b/target/linux/ixp4xx/patches-2.6.26/150-lanready_ap1000_support.patch
index d6d7cf6f7..fd1567bca 100644
--- a/target/linux/ixp4xx/patches-2.6.26/150-lanready_ap1000_support.patch
+++ b/target/linux/ixp4xx/patches-2.6.26/150-lanready_ap1000_support.patch
@@ -166,7 +166,7 @@
}
--- a/arch/arm/mach-ixp4xx/Kconfig
+++ b/arch/arm/mach-ixp4xx/Kconfig
-@@ -89,6 +89,14 @@
+@@ -107,6 +107,14 @@
WRT300N v2 router. For more information on this
platform, see http://openwrt.org
@@ -183,7 +183,7 @@
help
--- a/arch/arm/mach-ixp4xx/Makefile
+++ b/arch/arm/mach-ixp4xx/Makefile
-@@ -20,6 +20,7 @@
+@@ -21,6 +21,7 @@
obj-pci-$(CONFIG_MACH_COMPEX) += ixdp425-pci.o
obj-pci-$(CONFIG_MACH_WRT300NV2) += wrt300nv2-pci.o
obj-pci-$(CONFIG_MACH_SIDEWINDER) += sidewinder-pci.o
@@ -191,7 +191,7 @@
obj-y += common.o
-@@ -38,6 +39,7 @@
+@@ -40,6 +41,7 @@
obj-$(CONFIG_MACH_COMPEX) += compex-setup.o
obj-$(CONFIG_MACH_WRT300NV2) += wrt300nv2-setup.o
obj-$(CONFIG_MACH_SIDEWINDER) += sidewinder-setup.o
diff --git a/target/linux/ixp4xx/patches-2.6.26/161-wg302v1_mac_plat_info.patch b/target/linux/ixp4xx/patches-2.6.26/161-wg302v1_mac_plat_info.patch
deleted file mode 100644
index 76066fb9a..000000000
--- a/target/linux/ixp4xx/patches-2.6.26/161-wg302v1_mac_plat_info.patch
+++ /dev/null
@@ -1,30 +0,0 @@
---- a/arch/arm/mach-ixp4xx/wg302v1-setup.c
-+++ b/arch/arm/mach-ixp4xx/wg302v1-setup.c
-@@ -77,9 +77,27 @@
- .resource = &wg302v1_uart_resource,
- };
-
-+/* Built-in 10/100 Ethernet MAC interfaces */
-+static struct eth_plat_info wg302_plat_eth[] = {
-+ {
-+ .phy = 30,
-+ .rxq = 3,
-+ .txreadyq = 20,
-+ }
-+};
-+
-+static struct platform_device wg302_eth[] = {
-+ {
-+ .name = "ixp4xx_eth",
-+ .id = IXP4XX_ETH_NPEB,
-+ .dev.platform_data = wg302_plat_eth,
-+ }
-+};
-+
- static struct platform_device *wg302v1_devices[] __initdata = {
- &wg302v1_flash,
- &wg302v1_uart,
-+ &wg302_eth[0],
- };
-
- static void __init wg302v1_init(void)
diff --git a/target/linux/ixp4xx/patches-2.6.26/162-wg302v1_mem_fixup.patch b/target/linux/ixp4xx/patches-2.6.26/162-wg302v1_mem_fixup.patch
index f89698cca..4eb1b7595 100644
--- a/target/linux/ixp4xx/patches-2.6.26/162-wg302v1_mem_fixup.patch
+++ b/target/linux/ixp4xx/patches-2.6.26/162-wg302v1_mem_fixup.patch
@@ -1,7 +1,7 @@
--- a/arch/arm/mach-ixp4xx/wg302v1-setup.c
+++ b/arch/arm/mach-ixp4xx/wg302v1-setup.c
-@@ -100,6 +100,36 @@
- &wg302_eth[0],
+@@ -99,6 +99,36 @@
+ &wg302v1_eth[0],
};
+static char wg302v1_mem_fixup[] __initdata = "mem=32M ";
@@ -37,7 +37,7 @@
static void __init wg302v1_init(void)
{
ixp4xx_sys_init();
-@@ -118,6 +148,7 @@
+@@ -117,6 +147,7 @@
/* Maintainer: Imre Kaloz <kaloz@openwrt.org> */
.phys_io = IXP4XX_PERIPHERAL_BASE_PHYS,
.io_pg_offst = ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xfffc,
diff --git a/target/linux/ixp4xx/patches-2.6.26/180-tw5334_support.patch b/target/linux/ixp4xx/patches-2.6.26/180-tw5334_support.patch
index c403a87fc..2632f80e1 100644
--- a/target/linux/ixp4xx/patches-2.6.26/180-tw5334_support.patch
+++ b/target/linux/ixp4xx/patches-2.6.26/180-tw5334_support.patch
@@ -1,6 +1,6 @@
--- a/arch/arm/mach-ixp4xx/Kconfig
+++ b/arch/arm/mach-ixp4xx/Kconfig
-@@ -150,6 +150,14 @@
+@@ -160,6 +160,14 @@
PrPCM1100 Processor Mezanine Module. For more information on
this platform, see <file:Documentation/arm/IXP4xx>.
@@ -276,8 +276,8 @@
*/
if (machine_is_adi_coyote() || machine_is_gtwx5715() ||
machine_is_gateway7001() || machine_is_wg302v2() ||
-- machine_is_pronghorn_metro() || machine_is_wrt300nv2())
-+ machine_is_pronghorn_metro() || machine_is_wrt300nv2() ||
+- machine_is_pronghorn() || machine_is_pronghorn_metro() || machine_is_wrt300nv2())
++ machine_is_pronghorn() || machine_is_pronghorn_metro() || machine_is_wrt300nv2() ||
+ machine_is_tw5334())
uart_base = (volatile u32*) IXP4XX_UART2_BASE_PHYS;
else
diff --git a/target/linux/ixp4xx/patches-2.6.26/190-cambria_support.patch b/target/linux/ixp4xx/patches-2.6.26/190-cambria_support.patch
index 5e682b097..b63cb17aa 100644
--- a/target/linux/ixp4xx/patches-2.6.26/190-cambria_support.patch
+++ b/target/linux/ixp4xx/patches-2.6.26/190-cambria_support.patch
@@ -15,7 +15,7 @@
config MACH_LOFT
bool "Loft"
depends on MACH_AVILA
-@@ -200,7 +208,7 @@
+@@ -210,7 +218,7 @@
config CPU_IXP43X
bool
diff --git a/target/linux/ixp4xx/patches-2.6.26/204-npe_driver_ixp43x_support.patch b/target/linux/ixp4xx/patches-2.6.26/204-npe_driver_ixp43x_support.patch
index 411e0cb42..932fae582 100644
--- a/target/linux/ixp4xx/patches-2.6.26/204-npe_driver_ixp43x_support.patch
+++ b/target/linux/ixp4xx/patches-2.6.26/204-npe_driver_ixp43x_support.patch
@@ -1,3 +1,15 @@
+From cba5c286f3ea34ea4767fc00c705434a00fe2c37 Mon Sep 17 00:00:00 2001
+From: Imre Kaloz <kaloz@openwrt.org>
+Date: Thu, 26 Jun 2008 01:58:02 +0200
+Subject: [PATCH] Add support for the ethernet ports on IXP43x
+
+---
+ arch/arm/mach-ixp4xx/ixp4xx_npe.c | 6 +++---
+ drivers/net/arm/ixp4xx_eth.c | 13 +++++++++----
+ include/asm-arm/arch-ixp4xx/cpu.h | 2 ++
+ include/asm-arm/arch-ixp4xx/ixp4xx-regs.h | 7 ++++---
+ 4 files changed, 18 insertions(+), 10 deletions(-)
+
--- a/arch/arm/mach-ixp4xx/ixp4xx_npe.c
+++ b/arch/arm/mach-ixp4xx/ixp4xx_npe.c
@@ -575,8 +575,8 @@
diff --git a/target/linux/ixp4xx/patches-2.6.26/400-dmabounce.patch b/target/linux/ixp4xx/patches-2.6.26/400-dmabounce.patch
index 7dae29149..28230272e 100644
--- a/target/linux/ixp4xx/patches-2.6.26/400-dmabounce.patch
+++ b/target/linux/ixp4xx/patches-2.6.26/400-dmabounce.patch
@@ -13,7 +13,7 @@
--- a/arch/arm/mach-ixp4xx/Kconfig
+++ b/arch/arm/mach-ixp4xx/Kconfig
-@@ -236,6 +236,11 @@
+@@ -246,6 +246,11 @@
default y
depends on PCI