diff options
Diffstat (limited to 'target/linux/kirkwood/patches')
3 files changed, 0 insertions, 269 deletions
diff --git a/target/linux/kirkwood/patches/001-openwrt_partition_map.patch b/target/linux/kirkwood/patches/001-openwrt_partition_map.patch deleted file mode 100644 index 0f94adc34..000000000 --- a/target/linux/kirkwood/patches/001-openwrt_partition_map.patch +++ /dev/null @@ -1,11 +0,0 @@ ---- a/arch/arm/mach-kirkwood/sheevaplug-setup.c -+++ b/arch/arm/mach-kirkwood/sheevaplug-setup.c -@@ -33,7 +33,7 @@ static struct mtd_partition sheevaplug_n - .offset = MTDPART_OFS_NXTBLK, - .size = SZ_4M - }, { -- .name = "root", -+ .name = "rootfs", - .offset = MTDPART_OFS_NXTBLK, - .size = MTDPART_SIZ_FULL - }, diff --git a/target/linux/kirkwood/patches/002-mvsdio_delay.patch b/target/linux/kirkwood/patches/002-mvsdio_delay.patch deleted file mode 100644 index ba2885360..000000000 --- a/target/linux/kirkwood/patches/002-mvsdio_delay.patch +++ /dev/null @@ -1,32 +0,0 @@ ---- a/drivers/mmc/core/sd.c -+++ b/drivers/mmc/core/sd.c -@@ -332,6 +332,15 @@ int mmc_sd_switch_hs(struct mmc_card *ca - return -ENOMEM; - } - -+ /* -+ * Some SDHC cards, notably those with a Sandisk SD controller -+ * (also found in Kingston products) need a bit of slack -+ * before successfully handling the SWITCH command. So far, -+ * cards identifying themselves as "SD04G" and "SD08G" are -+ * affected -+ */ -+ udelay(1000); -+ - err = mmc_sd_switch(card, 1, 0, 1, status); - if (err) - goto out; ---- a/drivers/mmc/core/core.c -+++ b/drivers/mmc/core/core.c -@@ -303,9 +303,9 @@ void mmc_set_data_timeout(struct mmc_dat - * The limit is really 250 ms, but that is - * insufficient for some crappy cards. - */ -- limit_us = 300000; -+ limit_us = 500000; - else -- limit_us = 100000; -+ limit_us = 200000; - - /* - * SDHC cards always use these fixed values. diff --git a/target/linux/kirkwood/patches/200-iconnect.patch b/target/linux/kirkwood/patches/200-iconnect.patch deleted file mode 100644 index f8baae64a..000000000 --- a/target/linux/kirkwood/patches/200-iconnect.patch +++ /dev/null @@ -1,226 +0,0 @@ ---- a/arch/arm/mach-kirkwood/Makefile -+++ b/arch/arm/mach-kirkwood/Makefile -@@ -8,6 +8,7 @@ obj-$(CONFIG_MACH_SHEEVAPLUG) += sheeva - obj-$(CONFIG_MACH_ESATA_SHEEVAPLUG) += sheevaplug-setup.o - obj-$(CONFIG_MACH_GURUPLUG) += guruplug-setup.o - obj-$(CONFIG_MACH_DOCKSTAR) += dockstar-setup.o -+obj-$(CONFIG_MACH_ICONNECT) += iconnect-setup.o - obj-$(CONFIG_MACH_TS219) += ts219-setup.o tsx1x-common.o - obj-$(CONFIG_MACH_TS41X) += ts41x-setup.o tsx1x-common.o - obj-$(CONFIG_MACH_OPENRD) += openrd-setup.o ---- a/arch/arm/mach-kirkwood/Kconfig -+++ b/arch/arm/mach-kirkwood/Kconfig -@@ -130,6 +130,12 @@ config MACH_T5325 - Say 'Y' here if you want your kernel to support the - HP t5325 Thin Client. - -+config MACH_ICONNECT -+ bool "Iomega iConnect Wireless" -+ help -+ Say 'Y' here if you want your kernel to support the -+ Iomega iConnect Wireless. -+ - endmenu - - endif ---- a/arch/arm/mach-kirkwood/mpp.h -+++ b/arch/arm/mach-kirkwood/mpp.h -@@ -108,6 +108,7 @@ - #define MPP11_SATA0_ACTn MPP( 11, 0x5, 0, 1, 0, 1, 1, 1, 1 ) - - #define MPP12_GPO MPP( 12, 0x0, 0, 1, 1, 1, 1, 1, 1 ) -+#define MPP12_GPIO MPP( 12, 0x0, 1, 1, 1, 1, 1, 1, 1 ) - #define MPP12_SD_CLK MPP( 12, 0x1, 0, 1, 1, 1, 1, 1, 1 ) - #define MPP12_AU_SPDIF0 MPP( 12, 0xa, 0, 1, 0, 0, 0, 0, 1 ) - #define MPP12_SPI_MOSI MPP( 12, 0xb, 0, 1, 0, 0, 0, 0, 1 ) ---- /dev/null -+++ b/arch/arm/mach-kirkwood/iconnect-setup.c -@@ -0,0 +1,188 @@ -+/* -+ * arch/arm/mach-kirkwood/iconnect-setup.c -+ * -+ * Iomega iConnect Wireless -+ * -+ * This file is licensed under the terms of the GNU General Public -+ * License version 2. This program is licensed "as is" without any -+ * warranty of any kind, whether express or implied. -+ */ -+ -+#include <linux/kernel.h> -+#include <linux/init.h> -+#include <linux/platform_device.h> -+#include <linux/irq.h> -+#include <linux/mtd/partitions.h> -+#include <linux/mv643xx_eth.h> -+#include <linux/ethtool.h> -+#include <linux/gpio.h> -+#include <linux/gpio_keys.h> -+#include <linux/input.h> -+#include <linux/leds.h> -+#include <asm/mach-types.h> -+#include <asm/mach/arch.h> -+#include <mach/kirkwood.h> -+#include "common.h" -+#include "mpp.h" -+ -+static struct mtd_partition iconnect_nand_parts[] = { -+ { -+ .name = "u-boot", -+ .offset = 0, -+ .size = SZ_1M -+ }, { -+ .name = "uImage", -+ .offset = MTDPART_OFS_NXTBLK, -+ .size = SZ_1M + SZ_2M -+ }, { -+ .name = "rootfs", -+ .offset = MTDPART_OFS_NXTBLK, -+ .size = SZ_32M, -+ }, { -+ .name = "data", -+ .offset = MTDPART_OFS_NXTBLK, -+ .size = MTDPART_SIZ_FULL -+ }, -+}; -+ -+static struct mv643xx_eth_platform_data iconnect_ge00_data = { -+ .phy_addr = MV643XX_ETH_PHY_ADDR(11), -+}; -+ -+static struct gpio_led iconnect_led_pins[] = { -+ { -+ .name = "iconnect:blue:power", -+ .default_trigger = "default-on", -+ .gpio = 42, -+ }, -+ { -+ .name = "iconnect:red:power", -+ .gpio = 43, -+ }, -+ { -+ .name = "iconnect:blue:usb1", -+ .gpio = 44, -+ }, -+ { -+ .name = "iconnect:blue:usb2", -+ .gpio = 45, -+ }, -+ { -+ .name = "iconnect:blue:usb3", -+ .gpio = 46, -+ }, -+ { -+ .name = "iconnect:blue:usb4", -+ .gpio = 47, -+ }, -+ { -+ .name = "iconnect:blue:otb", -+ .gpio = 48, -+ }, -+}; -+ -+static struct gpio_led_platform_data iconnect_led_data = { -+ .leds = iconnect_led_pins, -+ .num_leds = ARRAY_SIZE(iconnect_led_pins), -+}; -+ -+static struct platform_device iconnect_leds = { -+ .name = "leds-gpio", -+ .id = -1, -+ .dev = { -+ .platform_data = &iconnect_led_data, -+ } -+}; -+ -+#define ICONNECT_GPIO_KEY_RESET 12 -+#define ICONNECT_GPIO_KEY_OTB 35 -+ -+#define ICONNECT_SW_RESET 0x00 -+#define ICONNECT_SW_OTB 0x01 -+ -+static struct gpio_keys_button iconnect_buttons[] = { -+ { -+ .type = EV_SW, -+ .code = ICONNECT_SW_RESET, -+ .gpio = ICONNECT_GPIO_KEY_RESET, -+ .desc = "Reset Button", -+ .active_low = 1, -+ .debounce_interval = 100, -+ }, -+ { -+ .type = EV_SW, -+ .code = ICONNECT_SW_OTB, -+ .gpio = ICONNECT_GPIO_KEY_OTB, -+ .desc = "OTB Button", -+ .active_low = 1, -+ .debounce_interval = 100, -+ }, -+}; -+ -+static struct gpio_keys_platform_data iconnect_button_data = { -+ .buttons = iconnect_buttons, -+ .nbuttons = ARRAY_SIZE(iconnect_buttons), -+}; -+ -+static struct platform_device iconnect_button_device = { -+ .name = "gpio-keys", -+ .id = -1, -+ .num_resources = 0, -+ .dev = { -+ .platform_data = &iconnect_button_data, -+ }, -+}; -+ -+static unsigned int iconnect_mpp_config[] __initdata = { -+ MPP12_GPIO, /*Input for reset button*/ -+ MPP35_GPIO, /*Input for OTB button*/ -+ MPP42_GPIO, -+ MPP43_GPIO, -+ MPP44_GPIO, -+ MPP45_GPIO, -+ MPP46_GPIO, -+ MPP47_GPIO, -+ MPP48_GPIO, -+ 0 -+}; -+ -+static void __init iconnect_init(void) -+{ -+ u32 dev, rev; -+ -+ /* -+ * Basic setup. Needs to be called early. -+ */ -+ kirkwood_init(); -+ kirkwood_mpp_conf(iconnect_mpp_config); -+ -+ kirkwood_nand_init(ARRAY_AND_SIZE(iconnect_nand_parts), 25); -+ kirkwood_ehci_init(); -+ -+ kirkwood_ge00_init(&iconnect_ge00_data); -+ kirkwood_pcie_id(&dev, &rev); -+ -+ kirkwood_uart0_init(); -+ kirkwood_i2c_init(); -+ -+ platform_device_register(&iconnect_leds); -+ platform_device_register(&iconnect_button_device); -+} -+ -+static int __init iconnect_pci_init(void) -+{ -+ if (machine_is_iconnect()) -+ kirkwood_pcie_init(KW_PCIE0); -+ -+ return 0; -+} -+subsys_initcall(iconnect_pci_init); -+ -+ -+MACHINE_START(ICONNECT, "Iomega iConnect Wireless") -+ .boot_params = 0x00000100, -+ .init_machine = iconnect_init, -+ .map_io = kirkwood_map_io, -+ .init_irq = kirkwood_init_irq, -+ .timer = &kirkwood_timer, -+MACHINE_END |