diff options
Diffstat (limited to 'target/linux/ixp4xx/patches-2.6.33')
45 files changed, 0 insertions, 6453 deletions
diff --git a/target/linux/ixp4xx/patches-2.6.33/020-gateworks_i2c_pld.patch b/target/linux/ixp4xx/patches-2.6.33/020-gateworks_i2c_pld.patch deleted file mode 100644 index b51e26dfa..000000000 --- a/target/linux/ixp4xx/patches-2.6.33/020-gateworks_i2c_pld.patch +++ /dev/null @@ -1,421 +0,0 @@ ---- /dev/null -+++ b/drivers/gpio/gw_i2c_pld.c -@@ -0,0 +1,371 @@ -+/* -+ * Gateworks I2C PLD GPIO expander -+ * -+ * Copyright (C) 2009 Gateworks Corporation -+ * -+ * This program is free software; you can redistribute it and/or modify -+ * it under the terms of the GNU General Public License as published by -+ * the Free Software Foundation; either version 2 of the License, or -+ * (at your option) any later version. -+ * -+ * This program is distributed in the hope that it will be useful, -+ * but WITHOUT ANY WARRANTY; without even the implied warranty of -+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -+ * GNU General Public License for more details. -+ * -+ * You should have received a copy of the GNU General Public License -+ * along with this program; if not, write to the Free Software -+ * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. -+ */ -+ -+#include <linux/kernel.h> -+#include <linux/slab.h> -+#include <linux/hardirq.h> -+#include <linux/i2c.h> -+#include <linux/i2c/gw_i2c_pld.h> -+#include <asm/gpio.h> -+ -+static const struct i2c_device_id gw_i2c_pld_id[] = { -+ { "gw_i2c_pld", 8 }, -+ { } -+}; -+MODULE_DEVICE_TABLE(i2c, gw_i2c_pld_id); -+ -+/* -+ * The Gateworks I2C PLD chip only expose one read and one -+ * write register. Writing a "one" bit (to match the reset state) lets -+ * that pin be used as an input. It is an open-drain model. -+ */ -+ -+struct gw_i2c_pld { -+ struct gpio_chip chip; -+ struct i2c_client *client; -+ unsigned out; /* software latch */ -+}; -+ -+/*-------------------------------------------------------------------------*/ -+ -+/* -+ * The Gateworks I2C PLD chip does not properly send the acknowledge bit -+ * thus we cannot use standard i2c_smbus functions. We have recreated -+ * our own here, but we still use the mutex_lock to lock the i2c_bus -+ * as the device still exists on the I2C bus. -+*/ -+ -+#define PLD_SCL_GPIO 6 -+#define PLD_SDA_GPIO 7 -+ -+#define SCL_LO() gpio_line_set(PLD_SCL_GPIO, IXP4XX_GPIO_LOW) -+#define SCL_HI() gpio_line_set(PLD_SCL_GPIO, IXP4XX_GPIO_HIGH) -+#define SCL_EN() gpio_line_config(PLD_SCL_GPIO, IXP4XX_GPIO_OUT) -+#define SDA_LO() gpio_line_set(PLD_SDA_GPIO, IXP4XX_GPIO_LOW) -+#define SDA_HI() gpio_line_set(PLD_SDA_GPIO, IXP4XX_GPIO_HIGH) -+#define SDA_EN() gpio_line_config(PLD_SDA_GPIO, IXP4XX_GPIO_OUT) -+#define SDA_DIS() gpio_line_config(PLD_SDA_GPIO, IXP4XX_GPIO_IN) -+#define SDA_IN(x) gpio_line_get(PLD_SDA_GPIO, &x); -+ -+static int i2c_pld_write_byte(int address, int byte) -+{ -+ int i; -+ -+ address = (address << 1) & ~0x1; -+ -+ SDA_HI(); -+ SDA_EN(); -+ SCL_EN(); -+ SCL_HI(); -+ SDA_LO(); -+ SCL_LO(); -+ -+ for (i = 7; i >= 0; i--) -+ { -+ if (address & (1 << i)) -+ SDA_HI(); -+ else -+ SDA_LO(); -+ -+ SCL_HI(); -+ SCL_LO(); -+ } -+ -+ SDA_DIS(); -+ SCL_HI(); -+ SDA_IN(i); -+ SCL_LO(); -+ SDA_EN(); -+ -+ for (i = 7; i >= 0; i--) -+ { -+ if (byte & (1 << i)) -+ SDA_HI(); -+ else -+ SDA_LO(); -+ SCL_HI(); -+ SCL_LO(); -+ } -+ -+ SDA_DIS(); -+ SCL_HI(); -+ SDA_IN(i); -+ SCL_LO(); -+ -+ SDA_HI(); -+ SDA_EN(); -+ -+ SDA_LO(); -+ SCL_HI(); -+ SDA_HI(); -+ SCL_LO(); -+ SCL_HI(); -+ -+ return 0; -+} -+ -+static unsigned int i2c_pld_read_byte(int address) -+{ -+ int i = 0, byte = 0; -+ int bit; -+ -+ address = (address << 1) | 0x1; -+ -+ SDA_HI(); -+ SDA_EN(); -+ SCL_EN(); -+ SCL_HI(); -+ SDA_LO(); -+ SCL_LO(); -+ -+ for (i = 7; i >= 0; i--) -+ { -+ if (address & (1 << i)) -+ SDA_HI(); -+ else -+ SDA_LO(); -+ -+ SCL_HI(); -+ SCL_LO(); -+ } -+ -+ SDA_DIS(); -+ SCL_HI(); -+ SDA_IN(i); -+ SCL_LO(); -+ SDA_EN(); -+ -+ SDA_DIS(); -+ for (i = 7; i >= 0; i--) -+ { -+ SCL_HI(); -+ SDA_IN(bit); -+ byte |= bit << i; -+ SCL_LO(); -+ } -+ -+ SDA_LO(); -+ SCL_HI(); -+ SDA_HI(); -+ SCL_LO(); -+ SCL_HI(); -+ -+ return byte; -+} -+ -+ -+static int gw_i2c_pld_input8(struct gpio_chip *chip, unsigned offset) -+{ -+ int ret; -+ struct gw_i2c_pld *gpio = container_of(chip, struct gw_i2c_pld, chip); -+ struct i2c_adapter *adap = gpio->client->adapter; -+ -+ if (in_atomic() || irqs_disabled()) { -+ ret = mutex_trylock(&adap->bus_lock); -+ if (!ret) -+ /* I2C activity is ongoing. */ -+ return -EAGAIN; -+ } else { -+ mutex_lock_nested(&adap->bus_lock, adap->level); -+ } -+ -+ gpio->out |= (1 << offset); -+ -+ ret = i2c_pld_write_byte(gpio->client->addr, gpio->out); -+ -+ mutex_unlock(&adap->bus_lock); -+ -+ return ret; -+} -+ -+static int gw_i2c_pld_get8(struct gpio_chip *chip, unsigned offset) -+{ -+ int ret; -+ s32 value; -+ struct gw_i2c_pld *gpio = container_of(chip, struct gw_i2c_pld, chip); -+ struct i2c_adapter *adap = gpio->client->adapter; -+ -+ if (in_atomic() || irqs_disabled()) { -+ ret = mutex_trylock(&adap->bus_lock); -+ if (!ret) -+ /* I2C activity is ongoing. */ -+ return -EAGAIN; -+ } else { -+ mutex_lock_nested(&adap->bus_lock, adap->level); -+ } -+ -+ value = i2c_pld_read_byte(gpio->client->addr); -+ -+ mutex_unlock(&adap->bus_lock); -+ -+ return (value < 0) ? 0 : (value & (1 << offset)); -+} -+ -+static int gw_i2c_pld_output8(struct gpio_chip *chip, unsigned offset, int value) -+{ -+ int ret; -+ -+ struct gw_i2c_pld *gpio = container_of(chip, struct gw_i2c_pld, chip); -+ struct i2c_adapter *adap = gpio->client->adapter; -+ -+ unsigned bit = 1 << offset; -+ -+ if (in_atomic() || irqs_disabled()) { -+ ret = mutex_trylock(&adap->bus_lock); -+ if (!ret) -+ /* I2C activity is ongoing. */ -+ return -EAGAIN; -+ } else { -+ mutex_lock_nested(&adap->bus_lock, adap->level); -+ } -+ -+ -+ if (value) -+ gpio->out |= bit; -+ else -+ gpio->out &= ~bit; -+ -+ ret = i2c_pld_write_byte(gpio->client->addr, gpio->out); -+ -+ mutex_unlock(&adap->bus_lock); -+ -+ return ret; -+} -+ -+static void gw_i2c_pld_set8(struct gpio_chip *chip, unsigned offset, int value) -+{ -+ gw_i2c_pld_output8(chip, offset, value); -+} -+ -+/*-------------------------------------------------------------------------*/ -+ -+static int gw_i2c_pld_probe(struct i2c_client *client, -+ const struct i2c_device_id *id) -+{ -+ struct gw_i2c_pld_platform_data *pdata; -+ struct gw_i2c_pld *gpio; -+ int status; -+ -+ pdata = client->dev.platform_data; -+ if (!pdata) -+ return -ENODEV; -+ -+ /* Allocate, initialize, and register this gpio_chip. */ -+ gpio = kzalloc(sizeof *gpio, GFP_KERNEL); -+ if (!gpio) -+ return -ENOMEM; -+ -+ gpio->chip.base = pdata->gpio_base; -+ gpio->chip.can_sleep = 1; -+ gpio->chip.dev = &client->dev; -+ gpio->chip.owner = THIS_MODULE; -+ -+ gpio->chip.ngpio = pdata->nr_gpio; -+ gpio->chip.direction_input = gw_i2c_pld_input8; -+ gpio->chip.get = gw_i2c_pld_get8; -+ gpio->chip.direction_output = gw_i2c_pld_output8; -+ gpio->chip.set = gw_i2c_pld_set8; -+ -+ gpio->chip.label = client->name; -+ -+ gpio->client = client; -+ i2c_set_clientdata(client, gpio); -+ -+ gpio->out = 0xFF; -+ -+ status = gpiochip_add(&gpio->chip); -+ if (status < 0) -+ goto fail; -+ -+ dev_info(&client->dev, "gpios %d..%d on a %s%s\n", -+ gpio->chip.base, -+ gpio->chip.base + gpio->chip.ngpio - 1, -+ client->name, -+ client->irq ? " (irq ignored)" : ""); -+ -+ /* Let platform code set up the GPIOs and their users. -+ * Now is the first time anyone could use them. -+ */ -+ if (pdata->setup) { -+ status = pdata->setup(client, -+ gpio->chip.base, gpio->chip.ngpio, -+ pdata->context); -+ if (status < 0) -+ dev_warn(&client->dev, "setup --> %d\n", status); -+ } -+ -+ return 0; -+ -+fail: -+ dev_dbg(&client->dev, "probe error %d for '%s'\n", -+ status, client->name); -+ kfree(gpio); -+ return status; -+} -+ -+static int gw_i2c_pld_remove(struct i2c_client *client) -+{ -+ struct gw_i2c_pld_platform_data *pdata = client->dev.platform_data; -+ struct gw_i2c_pld *gpio = i2c_get_clientdata(client); -+ int status = 0; -+ -+ if (pdata->teardown) { -+ status = pdata->teardown(client, -+ gpio->chip.base, gpio->chip.ngpio, -+ pdata->context); -+ if (status < 0) { -+ dev_err(&client->dev, "%s --> %d\n", -+ "teardown", status); -+ return status; -+ } -+ } -+ -+ status = gpiochip_remove(&gpio->chip); -+ if (status == 0) -+ kfree(gpio); -+ else -+ dev_err(&client->dev, "%s --> %d\n", "remove", status); -+ return status; -+} -+ -+static struct i2c_driver gw_i2c_pld_driver = { -+ .driver = { -+ .name = "gw_i2c_pld", -+ .owner = THIS_MODULE, -+ }, -+ .probe = gw_i2c_pld_probe, -+ .remove = gw_i2c_pld_remove, -+ .id_table = gw_i2c_pld_id, -+}; -+ -+static int __init gw_i2c_pld_init(void) -+{ -+ return i2c_add_driver(&gw_i2c_pld_driver); -+} -+module_init(gw_i2c_pld_init); -+ -+static void __exit gw_i2c_pld_exit(void) -+{ -+ i2c_del_driver(&gw_i2c_pld_driver); -+} -+module_exit(gw_i2c_pld_exit); -+ -+MODULE_LICENSE("GPL"); -+MODULE_AUTHOR("Chris Lang"); ---- a/drivers/gpio/Kconfig -+++ b/drivers/gpio/Kconfig -@@ -221,6 +221,14 @@ config GPIO_TIMBERDALE - ---help--- - Add support for the GPIO IP in the timberdale FPGA. - -+config GPIO_GW_I2C_PLD -+ tristate "Gateworks I2C PLD GPIO Expander" -+ depends on I2C -+ help -+ Say yes here to provide access to the Gateworks I2C PLD GPIO -+ Expander. This is used at least on the GW2358-4. -+ -+ - comment "SPI GPIO expanders:" - - config GPIO_MAX7301 ---- a/drivers/gpio/Makefile -+++ b/drivers/gpio/Makefile -@@ -22,3 +22,4 @@ obj-$(CONFIG_GPIO_CS5535) += cs5535-gpio - obj-$(CONFIG_GPIO_BT8XX) += bt8xxgpio.o - obj-$(CONFIG_GPIO_VR41XX) += vr41xx_giu.o - obj-$(CONFIG_GPIO_WM831X) += wm831x-gpio.o -+obj-$(CONFIG_GPIO_GW_I2C_PLD) += gw_i2c_pld.o ---- /dev/null -+++ b/include/linux/i2c/gw_i2c_pld.h -@@ -0,0 +1,20 @@ -+#ifndef __LINUX_GW_I2C_PLD_H -+#define __LINUX_GW_I2C_PLD_H -+ -+/** -+ * The Gateworks I2C PLD Implements an additional 8 bits of GPIO through the PLD -+ */ -+ -+struct gw_i2c_pld_platform_data { -+ unsigned gpio_base; -+ unsigned nr_gpio; -+ int (*setup)(struct i2c_client *client, -+ int gpio, unsigned ngpio, -+ void *context); -+ int (*teardown)(struct i2c_client *client, -+ int gpio, unsigned ngpio, -+ void *context); -+ void *context; -+}; -+ -+#endif /* __LINUX_GW_I2C_PLD_H */ diff --git a/target/linux/ixp4xx/patches-2.6.33/050-disable_dmabounce.patch b/target/linux/ixp4xx/patches-2.6.33/050-disable_dmabounce.patch deleted file mode 100644 index 08df48247..000000000 --- a/target/linux/ixp4xx/patches-2.6.33/050-disable_dmabounce.patch +++ /dev/null @@ -1,164 +0,0 @@ ---- a/arch/arm/Kconfig -+++ b/arch/arm/Kconfig -@@ -418,7 +418,6 @@ config ARCH_IXP4XX - select GENERIC_GPIO - select GENERIC_TIME - select GENERIC_CLOCKEVENTS -- select DMABOUNCE if PCI - help - Support for Intel's IXP4XX (XScale) family of processors. - ---- a/arch/arm/mach-ixp4xx/Kconfig -+++ b/arch/arm/mach-ixp4xx/Kconfig -@@ -199,6 +199,45 @@ config IXP4XX_INDIRECT_PCI - need to use the indirect method instead. If you don't know - what you need, leave this option unselected. - -+config IXP4XX_LEGACY_DMABOUNCE -+ bool "legacy PCI DMA bounce support" -+ depends on PCI -+ default n -+ select DMABOUNCE -+ help -+ The IXP4xx is limited to a 64MB window for PCI DMA, which -+ requires that PCI accesses above 64MB are bounced via buffers -+ below 64MB. Furthermore the IXP4xx has an erratum where PCI -+ read prefetches just below the 64MB limit can trigger lockups. -+ -+ The kernel has traditionally handled these two issue by using -+ ARM specific DMA bounce support code for all accesses >= 64MB. -+ That code causes problems of its own, so it is desirable to -+ disable it. As the kernel now has a workaround for the PCI read -+ prefetch erratum, it no longer requires the ARM bounce code. -+ -+ Enabling this option makes IXP4xx continue to use the problematic -+ ARM DMA bounce code. Disabling this option makes IXP4xx use the -+ kernel's generic bounce code. -+ -+ Say 'N'. -+ -+config IXP4XX_ZONE_DMA -+ bool "Support > 64MB RAM" -+ depends on !IXP4XX_LEGACY_DMABOUNCE -+ default y -+ select ZONE_DMA -+ help -+ The IXP4xx is limited to a 64MB window for PCI DMA, which -+ requires that PCI accesses above 64MB are bounced via buffers -+ below 64MB. -+ -+ Disabling this option allows you to omit the support code for -+ DMA-able memory allocations and DMA bouncing, but the kernel -+ will then not work properly if more than 64MB of RAM is present. -+ -+ Say 'Y' unless your platform is limited to <= 64MB of RAM. -+ - config IXP4XX_QMGR - tristate "IXP4xx Queue Manager support" - help ---- a/arch/arm/mach-ixp4xx/common-pci.c -+++ b/arch/arm/mach-ixp4xx/common-pci.c -@@ -321,27 +321,38 @@ static int abort_handler(unsigned long a - */ - static int ixp4xx_pci_platform_notify(struct device *dev) - { -- if(dev->bus == &pci_bus_type) { -- *dev->dma_mask = SZ_64M - 1; -+ if (dev->bus == &pci_bus_type) { -+ *dev->dma_mask = SZ_64M - 1; - dev->coherent_dma_mask = SZ_64M - 1; -+#ifdef CONFIG_DMABOUNCE - dmabounce_register_dev(dev, 2048, 4096); -+#endif - } - return 0; - } - - static int ixp4xx_pci_platform_notify_remove(struct device *dev) - { -- if(dev->bus == &pci_bus_type) { -+#ifdef CONFIG_DMABOUNCE -+ if (dev->bus == &pci_bus_type) - dmabounce_unregister_dev(dev); -- } -+#endif - return 0; - } - -+#ifdef CONFIG_DMABOUNCE - int dma_needs_bounce(struct device *dev, dma_addr_t dma_addr, size_t size) - { -+ /* Note that this returns true for the last page below 64M due to -+ * IXP4xx erratum 15 (SCR 1289), which states that PCI prefetches -+ * can cross the boundary between valid memory and a reserved region -+ * causing AHB bus errors and a lock-up. -+ */ - return (dev->bus == &pci_bus_type ) && ((dma_addr + size) >= SZ_64M); - } -+#endif - -+#ifdef CONFIG_ZONE_DMA - /* - * Only first 64MB of memory can be accessed via PCI. - * We use GFP_DMA to allocate safe buffers to do map/unmap. -@@ -364,6 +375,7 @@ void __init ixp4xx_adjust_zones(int node - zhole_size[1] = zhole_size[0]; - zhole_size[0] = 0; - } -+#endif - - void __init ixp4xx_pci_preinit(void) - { -@@ -513,19 +525,35 @@ struct pci_bus * __devinit ixp4xx_scan_b - int - pci_set_dma_mask(struct pci_dev *dev, u64 mask) - { -- if (mask >= SZ_64M - 1 ) -+#ifdef CONFIG_DMABOUNCE -+ if (mask >= SZ_64M - 1) - return 0; - - return -EIO; -+#else -+ /* Only honour masks < SZ_64M. Silently ignore masks >= SZ_64M -+ as generic drivers do not know about IXP4xx PCI DMA quirks. */ -+ if (mask < SZ_64M) -+ dev->dma_mask = mask; -+ return 0; -+#endif - } - - int - pci_set_consistent_dma_mask(struct pci_dev *dev, u64 mask) - { -- if (mask >= SZ_64M - 1 ) -+#ifdef CONFIG_DMABOUNCE -+ if (mask >= SZ_64M - 1) - return 0; - - return -EIO; -+#else -+ /* Only honour masks < SZ_64M. Silently ignore masks >= SZ_64M -+ as generic drivers do not know about IXP4xx PCI DMA quirks. */ -+ if (mask < SZ_64M) -+ dev->dev.coherent_dma_mask = mask; -+ return 0; -+#endif - } - - EXPORT_SYMBOL(ixp4xx_pci_read); ---- a/arch/arm/mach-ixp4xx/include/mach/memory.h -+++ b/arch/arm/mach-ixp4xx/include/mach/memory.h -@@ -16,10 +16,12 @@ - - #if !defined(__ASSEMBLY__) && defined(CONFIG_PCI) - -+#ifdef CONFIG_ZONE_DMA - void ixp4xx_adjust_zones(int node, unsigned long *size, unsigned long *holes); - - #define arch_adjust_zones(node, size, holes) \ - ixp4xx_adjust_zones(node, size, holes) -+#endif - - #define ISA_DMA_THRESHOLD (SZ_64M - 1) - #define MAX_DMA_ADDRESS (PAGE_OFFSET + SZ_64M) diff --git a/target/linux/ixp4xx/patches-2.6.33/090-increase_entropy_pools.patch b/target/linux/ixp4xx/patches-2.6.33/090-increase_entropy_pools.patch deleted file mode 100644 index f67b9b0e7..000000000 --- a/target/linux/ixp4xx/patches-2.6.33/090-increase_entropy_pools.patch +++ /dev/null @@ -1,15 +0,0 @@ ---- a/drivers/char/random.c -+++ b/drivers/char/random.c -@@ -264,9 +264,9 @@ - /* - * Configuration information - */ --#define INPUT_POOL_WORDS 128 --#define OUTPUT_POOL_WORDS 32 --#define SEC_XFER_SIZE 512 -+#define INPUT_POOL_WORDS 256 -+#define OUTPUT_POOL_WORDS 64 -+#define SEC_XFER_SIZE 1024 - - /* - * The minimum number of bits of entropy before we wake up a read on diff --git a/target/linux/ixp4xx/patches-2.6.33/100-wg302v2_gateway7001_mac_plat_info.patch b/target/linux/ixp4xx/patches-2.6.33/100-wg302v2_gateway7001_mac_plat_info.patch deleted file mode 100644 index a19a4085a..000000000 --- a/target/linux/ixp4xx/patches-2.6.33/100-wg302v2_gateway7001_mac_plat_info.patch +++ /dev/null @@ -1,68 +0,0 @@ ---- a/arch/arm/mach-ixp4xx/gateway7001-setup.c -+++ b/arch/arm/mach-ixp4xx/gateway7001-setup.c -@@ -76,9 +76,35 @@ static struct platform_device gateway700 - .resource = &gateway7001_uart_resource, - }; - -+static struct eth_plat_info gateway7001_plat_eth[] = { -+ { -+ .phy = 1, -+ .rxq = 3, -+ .txreadyq = 20, -+ }, { -+ .phy = 2, -+ .rxq = 4, -+ .txreadyq = 21, -+ } -+}; -+ -+static struct platform_device gateway7001_eth[] = { -+ { -+ .name = "ixp4xx_eth", -+ .id = IXP4XX_ETH_NPEB, -+ .dev.platform_data = gateway7001_plat_eth, -+ }, { -+ .name = "ixp4xx_eth", -+ .id = IXP4XX_ETH_NPEC, -+ .dev.platform_data = gateway7001_plat_eth + 1, -+ } -+}; -+ - static struct platform_device *gateway7001_devices[] __initdata = { - &gateway7001_flash, -- &gateway7001_uart -+ &gateway7001_uart, -+ &gateway7001_eth[0], -+ &gateway7001_eth[1], - }; - - static void __init gateway7001_init(void) ---- a/arch/arm/mach-ixp4xx/wg302v2-setup.c -+++ b/arch/arm/mach-ixp4xx/wg302v2-setup.c -@@ -77,9 +77,26 @@ static struct platform_device wg302v2_ua - .resource = &wg302v2_uart_resource, - }; - -+static struct eth_plat_info wg302v2_plat_eth[] = { -+ { -+ .phy = 8, -+ .rxq = 3, -+ .txreadyq = 20, -+ } -+}; -+ -+static struct platform_device wg302v2_eth[] = { -+ { -+ .name = "ixp4xx_eth", -+ .id = IXP4XX_ETH_NPEB, -+ .dev.platform_data = wg302v2_plat_eth, -+ } -+}; -+ - static struct platform_device *wg302v2_devices[] __initdata = { - &wg302v2_flash, - &wg302v2_uart, -+ &wg302v2_eth[0], - }; - - static void __init wg302v2_init(void) diff --git a/target/linux/ixp4xx/patches-2.6.33/105-wg302v1_support.patch b/target/linux/ixp4xx/patches-2.6.33/105-wg302v1_support.patch deleted file mode 100644 index e8b4342e7..000000000 --- a/target/linux/ixp4xx/patches-2.6.33/105-wg302v1_support.patch +++ /dev/null @@ -1,257 +0,0 @@ ---- a/arch/arm/configs/ixp4xx_defconfig -+++ b/arch/arm/configs/ixp4xx_defconfig -@@ -155,6 +155,7 @@ CONFIG_MACH_AVILA=y - CONFIG_MACH_LOFT=y - CONFIG_ARCH_ADI_COYOTE=y - CONFIG_MACH_GATEWAY7001=y -+CONFIG_MACH_WG302V1=y - CONFIG_MACH_WG302V2=y - CONFIG_ARCH_IXDP425=y - CONFIG_MACH_IXDPG425=y ---- a/arch/arm/mach-ixp4xx/Kconfig -+++ b/arch/arm/mach-ixp4xx/Kconfig -@@ -49,6 +49,14 @@ config MACH_GATEWAY7001 - 7001 Access Point. For more information on this platform, - see http://openwrt.org - -+config MACH_WG302V1 -+ bool "Netgear WG302 v1 / WAG302 v1" -+ select PCI -+ help -+ Say 'Y' here if you want your kernel to support Netgear's -+ WG302 v1 or WAG302 v1 Access Points. For more information -+ on this platform, see http://openwrt.org -+ - config MACH_WG302V2 - bool "Netgear WG302 v2 / WAG302 v2" - select PCI ---- a/arch/arm/mach-ixp4xx/Makefile -+++ b/arch/arm/mach-ixp4xx/Makefile -@@ -14,6 +14,7 @@ obj-pci-$(CONFIG_MACH_NSLU2) += nslu2-p - obj-pci-$(CONFIG_MACH_NAS100D) += nas100d-pci.o - obj-pci-$(CONFIG_MACH_DSMG600) += dsmg600-pci.o - obj-pci-$(CONFIG_MACH_GATEWAY7001) += gateway7001-pci.o -+obj-pci-$(CONFIG_MACH_WG302V1) += wg302v1-pci.o - obj-pci-$(CONFIG_MACH_WG302V2) += wg302v2-pci.o - obj-pci-$(CONFIG_MACH_FSG) += fsg-pci.o - -@@ -28,6 +29,7 @@ obj-$(CONFIG_MACH_NSLU2) += nslu2-setup. - obj-$(CONFIG_MACH_NAS100D) += nas100d-setup.o - obj-$(CONFIG_MACH_DSMG600) += dsmg600-setup.o - obj-$(CONFIG_MACH_GATEWAY7001) += gateway7001-setup.o -+obj-$(CONFIG_MACH_WG302V1) += wg302v1-setup.o - obj-$(CONFIG_MACH_WG302V2) += wg302v2-setup.o - obj-$(CONFIG_MACH_FSG) += fsg-setup.o - obj-$(CONFIG_MACH_GORAMO_MLR) += goramo_mlr.o ---- /dev/null -+++ b/arch/arm/mach-ixp4xx/wg302v1-pci.c -@@ -0,0 +1,64 @@ -+/* -+ * arch/arch/mach-ixp4xx/wg302v1-pci.c -+ * -+ * PCI setup routines for the Netgear WG302 v1 and WAG302 v1 -+ * -+ * Copyright (C) 2008 Imre Kaloz <kaloz@openwrt.org> -+ * -+ * based on coyote-pci.c: -+ * Copyright (C) 2002 Jungo Software Technologies. -+ * Copyright (C) 2003 MontaVista Software, Inc. -+ * -+ * Maintainer: Imre Kaloz <kaloz@openwrt.org> -+ * -+ * This program is free software; you can redistribute it and/or modify -+ * it under the terms of the GNU General Public License version 2 as -+ * published by the Free Software Foundation. -+ * -+ */ -+ -+#include <linux/kernel.h> -+#include <linux/pci.h> -+#include <linux/init.h> -+#include <linux/irq.h> -+ -+#include <asm/mach-types.h> -+#include <mach/hardware.h> -+ -+#include <asm/mach/pci.h> -+ -+void __init wg302v1_pci_preinit(void) -+{ -+ set_irq_type(IRQ_IXP4XX_GPIO8, IRQ_TYPE_LEVEL_LOW); -+ set_irq_type(IRQ_IXP4XX_GPIO10, IRQ_TYPE_LEVEL_LOW); -+ -+ ixp4xx_pci_preinit(); -+} -+ -+static int __init wg302v1_map_irq(struct pci_dev *dev, u8 slot, u8 pin) -+{ -+ if (slot == 1) -+ return IRQ_IXP4XX_GPIO8; -+ else if (slot == 2) -+ return IRQ_IXP4XX_GPIO10; -+ else -+ return -1; -+} -+ -+struct hw_pci wg302v1_pci __initdata = { -+ .nr_controllers = 1, -+ .preinit = wg302v1_pci_preinit, -+ .swizzle = pci_std_swizzle, -+ .setup = ixp4xx_setup, -+ .scan = ixp4xx_scan_bus, -+ .map_irq = wg302v1_map_irq, -+}; -+ -+int __init wg302v1_pci_init(void) -+{ -+ if (machine_is_wg302v1()) -+ pci_common_init(&wg302v1_pci); -+ return 0; -+} -+ -+subsys_initcall(wg302v1_pci_init); ---- /dev/null -+++ b/arch/arm/mach-ixp4xx/wg302v1-setup.c -@@ -0,0 +1,142 @@ -+/* -+ * arch/arm/mach-ixp4xx/wg302v1-setup.c -+ * -+ * Board setup for the Netgear WG302 v1 and WAG302 v1 -+ * -+ * Copyright (C) 2008 Imre Kaloz <kaloz@openwrt.org> -+ * -+ * based on coyote-setup.c: -+ * Copyright (C) 2003-2005 MontaVista Software, Inc. -+ * -+ * Author: Imre Kaloz <kaloz@openwrt.org> -+ * -+ */ -+ -+#include <linux/kernel.h> -+#include <linux/init.h> -+#include <linux/device.h> -+#include <linux/serial.h> -+#include <linux/tty.h> -+#include <linux/serial_8250.h> -+#include <linux/slab.h> -+#include <linux/types.h> -+#include <linux/memory.h> -+ -+#include <asm/setup.h> -+#include <mach/hardware.h> -+#include <asm/irq.h> -+#include <asm/mach-types.h> -+#include <asm/mach/arch.h> -+#include <asm/mach/flash.h> -+ -+static struct flash_platform_data wg302v1_flash_data = { -+ .map_name = "cfi_probe", -+ .width = 2, -+}; -+ -+static struct resource wg302v1_flash_resource = { -+ .flags = IORESOURCE_MEM, -+}; -+ -+static struct platform_device wg302v1_flash = { -+ .name = "IXP4XX-Flash", -+ .id = 0, -+ .dev = { -+ .platform_data = &wg302v1_flash_data, -+ }, -+ .num_resources = 1, -+ .resource = &wg302v1_flash_resource, -+}; -+ -+static struct resource wg302v1_uart_resources[] = { -+ { -+ .start = IXP4XX_UART1_BASE_PHYS, -+ .end = IXP4XX_UART1_BASE_PHYS + 0x0fff, -+ .flags = IORESOURCE_MEM, -+ }, -+ { -+ .start = IXP4XX_UART2_BASE_PHYS, -+ .end = IXP4XX_UART2_BASE_PHYS + 0x0fff, -+ .flags = IORESOURCE_MEM, -+ } -+}; -+ -+static struct plat_serial8250_port wg302v1_uart_data[] = { -+ { -+ .mapbase = IXP4XX_UART1_BASE_PHYS, -+ .membase = (char *)IXP4XX_UART1_BASE_VIRT + REG_OFFSET, -+ .irq = IRQ_IXP4XX_UART1, -+ .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST, -+ .iotype = UPIO_MEM, -+ .regshift = 2, -+ .uartclk = IXP4XX_UART_XTAL, -+ }, -+ { -+ .mapbase = IXP4XX_UART2_BASE_PHYS, -+ .membase = (char *)IXP4XX_UART2_BASE_VIRT + REG_OFFSET, -+ .irq = IRQ_IXP4XX_UART2, -+ .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST, -+ .iotype = UPIO_MEM, -+ .regshift = 2, -+ .uartclk = IXP4XX_UART_XTAL, -+ }, -+ { }, -+}; -+ -+static struct platform_device wg302v1_uart = { -+ .name = "serial8250", -+ .id = PLAT8250_DEV_PLATFORM, -+ .dev = { -+ .platform_data = wg302v1_uart_data, -+ }, -+ .num_resources = 2, -+ .resource = wg302v1_uart_resources, -+}; -+ -+static struct eth_plat_info wg302v1_plat_eth[] = { -+ { -+ .phy = 30, -+ .rxq = 3, -+ .txreadyq = 20, -+ } -+}; -+ -+static struct platform_device wg302v1_eth[] = { -+ { -+ .name = "ixp4xx_eth", -+ .id = IXP4XX_ETH_NPEB, -+ .dev.platform_data = wg302v1_plat_eth, -+ } -+}; -+ -+static struct platform_device *wg302v1_devices[] __initdata = { -+ &wg302v1_flash, -+ &wg302v1_uart, -+ &wg302v1_eth[0], -+}; -+ -+static void __init wg302v1_init(void) -+{ -+ ixp4xx_sys_init(); -+ -+ wg302v1_flash_resource.start = IXP4XX_EXP_BUS_BASE(0); -+ wg302v1_flash_resource.end = IXP4XX_EXP_BUS_BASE(0) + SZ_32M - 1; -+ -+ *IXP4XX_EXP_CS0 |= IXP4XX_FLASH_WRITABLE; -+ *IXP4XX_EXP_CS1 = *IXP4XX_EXP_CS0; -+ -+ platform_add_devices(wg302v1_devices, ARRAY_SIZE(wg302v1_devices)); -+} -+ -+#ifdef CONFIG_MACH_WG302V1 -+MACHINE_START(WG302V1, "Netgear WG302 v1 / WAG302 v1") -+ /* Maintainer: Imre Kaloz <kaloz@openwrt.org> */ -+ .phys_io = IXP4XX_PERIPHERAL_BASE_PHYS, -+ .io_pg_offst = ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xfffc, -+ .map_io = ixp4xx_map_io, -+ .init_irq = ixp4xx_init_irq, -+ .timer = &ixp4xx_timer, -+ .boot_params = 0x0100, -+ .init_machine = wg302v1_init, -+MACHINE_END -+#endif diff --git a/target/linux/ixp4xx/patches-2.6.33/110-pronghorn_series_support.patch b/target/linux/ixp4xx/patches-2.6.33/110-pronghorn_series_support.patch deleted file mode 100644 index c03869226..000000000 --- a/target/linux/ixp4xx/patches-2.6.33/110-pronghorn_series_support.patch +++ /dev/null @@ -1,387 +0,0 @@ ---- a/arch/arm/configs/ixp4xx_defconfig -+++ b/arch/arm/configs/ixp4xx_defconfig -@@ -157,6 +157,8 @@ CONFIG_ARCH_ADI_COYOTE=y - CONFIG_MACH_GATEWAY7001=y - CONFIG_MACH_WG302V1=y - CONFIG_MACH_WG302V2=y -+CONFIG_MACH_PRONGHORN=y -+CONFIG_MACH_PRONGHORNMETRO=y - CONFIG_ARCH_IXDP425=y - CONFIG_MACH_IXDPG425=y - CONFIG_MACH_IXDP465=y ---- a/arch/arm/mach-ixp4xx/Kconfig -+++ b/arch/arm/mach-ixp4xx/Kconfig -@@ -65,6 +65,22 @@ config MACH_WG302V2 - WG302 v2 or WAG302 v2 Access Points. For more information - on this platform, see http://openwrt.org - -+config MACH_PRONGHORN -+ bool "ADI Pronghorn series" -+ select PCI -+ help -+ Say 'Y' here if you want your kernel to support the ADI -+ Engineering Pronghorn series. For more -+ information on this platform, see http://www.adiengineering.com -+ -+# -+# There're only minimal differences kernel-wise between the Pronghorn and -+# Pronghorn Metro boards - they use different chip selects to drive the -+# CF slot connected to the expansion bus, so we just enable them together. -+# -+config MACH_PRONGHORNMETRO -+ def_bool MACH_PRONGHORN -+ - config ARCH_IXDP425 - bool "IXDP425" - help ---- a/arch/arm/mach-ixp4xx/Makefile -+++ b/arch/arm/mach-ixp4xx/Makefile -@@ -17,6 +17,7 @@ obj-pci-$(CONFIG_MACH_GATEWAY7001) += ga - obj-pci-$(CONFIG_MACH_WG302V1) += wg302v1-pci.o - obj-pci-$(CONFIG_MACH_WG302V2) += wg302v2-pci.o - obj-pci-$(CONFIG_MACH_FSG) += fsg-pci.o -+obj-pci-$(CONFIG_MACH_PRONGHORN) += pronghorn-pci.o - - obj-y += common.o - -@@ -33,6 +34,7 @@ obj-$(CONFIG_MACH_WG302V1) += wg302v1-se - obj-$(CONFIG_MACH_WG302V2) += wg302v2-setup.o - obj-$(CONFIG_MACH_FSG) += fsg-setup.o - obj-$(CONFIG_MACH_GORAMO_MLR) += goramo_mlr.o -+obj-$(CONFIG_MACH_PRONGHORN) += pronghorn-setup.o - - obj-$(CONFIG_PCI) += $(obj-pci-$(CONFIG_PCI)) common-pci.o - obj-$(CONFIG_IXP4XX_QMGR) += ixp4xx_qmgr.o ---- /dev/null -+++ b/arch/arm/mach-ixp4xx/pronghorn-pci.c -@@ -0,0 +1,70 @@ -+/* -+ * arch/arch/mach-ixp4xx/pronghorn-pci.c -+ * -+ * PCI setup routines for ADI Engineering Pronghorn series -+ * -+ * Copyright (C) 2008 Imre Kaloz <kaloz@openwrt.org> -+ * -+ * based on coyote-pci.c: -+ * Copyright (C) 2002 Jungo Software Technologies. -+ * Copyright (C) 2003 MontaVista Softwrae, Inc. -+ * -+ * Maintainer: Imre Kaloz <kaloz@openwrt.org> -+ * -+ * This program is free software; you can redistribute it and/or modify -+ * it under the terms of the GNU General Public License version 2 as -+ * published by the Free Software Foundation. -+ * -+ */ -+ -+#include <linux/kernel.h> -+#include <linux/pci.h> -+#include <linux/init.h> -+#include <linux/irq.h> -+ -+#include <asm/mach-types.h> -+#include <mach/hardware.h> -+ -+#include <asm/mach/pci.h> -+ -+void __init pronghorn_pci_preinit(void) -+{ -+ set_irq_type(IRQ_IXP4XX_GPIO4, IRQ_TYPE_LEVEL_LOW); -+ set_irq_type(IRQ_IXP4XX_GPIO6, IRQ_TYPE_LEVEL_LOW); -+ set_irq_type(IRQ_IXP4XX_GPIO11, IRQ_TYPE_LEVEL_LOW); -+ set_irq_type(IRQ_IXP4XX_GPIO1, IRQ_TYPE_LEVEL_LOW); -+ -+ ixp4xx_pci_preinit(); -+} -+ -+static int __init pronghorn_map_irq(struct pci_dev *dev, u8 slot, u8 pin) -+{ -+ if (slot == 13) -+ return IRQ_IXP4XX_GPIO4; -+ else if (slot == 14) -+ return IRQ_IXP4XX_GPIO6; -+ else if (slot == 15) -+ return IRQ_IXP4XX_GPIO11; -+ else if (slot == 16) -+ return IRQ_IXP4XX_GPIO1; -+ else -+ return -1; -+} -+ -+struct hw_pci pronghorn_pci __initdata = { -+ .nr_controllers = 1, -+ .preinit = pronghorn_pci_preinit, -+ .swizzle = pci_std_swizzle, -+ .setup = ixp4xx_setup, -+ .scan = ixp4xx_scan_bus, -+ .map_irq = pronghorn_map_irq, -+}; -+ -+int __init pronghorn_pci_init(void) -+{ -+ if (machine_is_pronghorn() || machine_is_pronghorn_metro()) -+ pci_common_init(&pronghorn_pci); -+ return 0; -+} -+ -+subsys_initcall(pronghorn_pci_init); ---- /dev/null -+++ b/arch/arm/mach-ixp4xx/pronghorn-setup.c -@@ -0,0 +1,245 @@ -+/* -+ * arch/arm/mach-ixp4xx/pronghorn-setup.c -+ * -+ * Board setup for the ADI Engineering Pronghorn series -+ * -+ * Copyright (C) 2008 Imre Kaloz <Kaloz@openwrt.org> -+ * -+ * based on coyote-setup.c: -+ * Copyright (C) 2003-2005 MontaVista Software, Inc. -+ * -+ * Author: Imre Kaloz <Kaloz@openwrt.org> -+ */ -+ -+#include <linux/kernel.h> -+#include <linux/init.h> -+#include <linux/device.h> -+#include <linux/serial.h> -+#include <linux/tty.h> -+#include <linux/serial_8250.h> -+#include <linux/slab.h> -+#include <linux/types.h> -+#include <linux/memory.h> -+#include <linux/i2c-gpio.h> -+#include <linux/leds.h> -+ -+#include <asm/setup.h> -+#include <mach/hardware.h> -+#include <asm/irq.h> -+#include <asm/mach-types.h> -+#include <asm/mach/arch.h> -+#include <asm/mach/flash.h> -+ -+static struct flash_platform_data pronghorn_flash_data = { -+ .map_name = "cfi_probe", -+ .width = 2, -+}; -+ -+static struct resource pronghorn_flash_resource = { -+ .flags = IORESOURCE_MEM, -+}; -+ -+static struct platform_device pronghorn_flash = { -+ .name = "IXP4XX-Flash", -+ .id = 0, -+ .dev = { -+ .platform_data = &pronghorn_flash_data, -+ }, -+ .num_resources = 1, -+ .resource = &pronghorn_flash_resource, -+}; -+ -+static struct resource pronghorn_uart_resources [] = { -+ { -+ .start = IXP4XX_UART1_BASE_PHYS, -+ .end = IXP4XX_UART1_BASE_PHYS + 0x0fff, -+ .flags = IORESOURCE_MEM -+ }, -+ { -+ .start = IXP4XX_UART2_BASE_PHYS, -+ .end = IXP4XX_UART2_BASE_PHYS + 0x0fff, -+ .flags = IORESOURCE_MEM -+ } -+}; -+ -+static struct plat_serial8250_port pronghorn_uart_data[] = { -+ { -+ .mapbase = IXP4XX_UART1_BASE_PHYS, -+ .membase = (char *)IXP4XX_UART1_BASE_VIRT + REG_OFFSET, -+ .irq = IRQ_IXP4XX_UART1, -+ .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST, -+ .iotype = UPIO_MEM, -+ .regshift = 2, -+ .uartclk = IXP4XX_UART_XTAL, -+ }, -+ { -+ .mapbase = IXP4XX_UART2_BASE_PHYS, -+ .membase = (char *)IXP4XX_UART2_BASE_VIRT + REG_OFFSET, -+ .irq = IRQ_IXP4XX_UART2, -+ .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST, -+ .iotype = UPIO_MEM, -+ .regshift = 2, -+ .uartclk = IXP4XX_UART_XTAL, -+ }, -+ { }, -+}; -+ -+static struct platform_device pronghorn_uart = { -+ .name = "serial8250", -+ .id = PLAT8250_DEV_PLATFORM, -+ .dev = { -+ .platform_data = pronghorn_uart_data, -+ }, -+ .num_resources = 2, -+ .resource = pronghorn_uart_resources, -+}; -+ -+static struct i2c_gpio_platform_data pronghorn_i2c_gpio_data = { -+ .sda_pin = 9, -+ .scl_pin = 10, -+}; -+ -+static struct platform_device pronghorn_i2c_gpio = { -+ .name = "i2c-gpio", -+ .id = 0, -+ .dev = { -+ .platform_data = &pronghorn_i2c_gpio_data, -+ }, -+}; -+ -+static struct gpio_led pronghorn_led_pin[] = { -+ { -+ .name = "pronghorn:green:status", -+ .gpio = 7, -+ } -+}; -+ -+static struct gpio_led_platform_data pronghorn_led_data = { -+ .num_leds = 1, -+ .leds = pronghorn_led_pin, -+}; -+ -+static struct platform_device pronghorn_led = { -+ .name = "leds-gpio", -+ .id = -1, -+ .dev.platform_data = &pronghorn_led_data, -+}; -+ -+static struct resource pronghorn_pata_resources[] = { -+ { -+ .flags = IORESOURCE_MEM -+ }, -+ { -+ .flags = IORESOURCE_MEM, -+ }, -+ { -+ .name = "intrq", -+ .start = IRQ_IXP4XX_GPIO0, -+ .end = IRQ_IXP4XX_GPIO0, -+ .flags = IORESOURCE_IRQ, -+ }, -+}; -+ -+static struct ixp4xx_pata_data pronghorn_pata_data = { -+ .cs0_bits = 0xbfff0043, -+ .cs1_bits = 0xbfff0043, -+}; -+ -+static struct platform_device pronghorn_pata = { -+ .name = "pata_ixp4xx_cf", -+ .id = 0, -+ .dev.platform_data = &pronghorn_pata_data, -+ .num_resources = ARRAY_SIZE(pronghorn_pata_resources), -+ .resource = pronghorn_pata_resources, -+}; -+ -+static struct eth_plat_info pronghorn_plat_eth[] = { -+ { -+ .phy = 0, -+ .rxq = 3, -+ .txreadyq = 20, -+ }, { -+ .phy = 1, -+ .rxq = 4, -+ .txreadyq = 21, -+ } -+}; -+ -+static struct platform_device pronghorn_eth[] = { -+ { -+ .name = "ixp4xx_eth", -+ .id = IXP4XX_ETH_NPEB, -+ .dev.platform_data = pronghorn_plat_eth, -+ }, { -+ .name = "ixp4xx_eth", -+ .id = IXP4XX_ETH_NPEC, -+ .dev.platform_data = pronghorn_plat_eth + 1, -+ } -+}; -+ -+static struct platform_device *pronghorn_devices[] __initdata = { -+ &pronghorn_flash, -+ &pronghorn_uart, -+ &pronghorn_led, -+ &pronghorn_eth[0], -+ &pronghorn_eth[1], -+}; -+ -+static void __init pronghorn_init(void) -+{ -+ ixp4xx_sys_init(); -+ -+ pronghorn_flash_resource.start = IXP4XX_EXP_BUS_BASE(0); -+ pronghorn_flash_resource.end = IXP4XX_EXP_BUS_BASE(0) + SZ_32M - 1; -+ -+ *IXP4XX_EXP_CS0 |= IXP4XX_FLASH_WRITABLE; -+ *IXP4XX_EXP_CS1 = *IXP4XX_EXP_CS0; -+ -+ platform_add_devices(pronghorn_devices, ARRAY_SIZE(pronghorn_devices)); -+ -+ if (machine_is_pronghorn()) { -+ pronghorn_pata_resources[0].start = IXP4XX_EXP_BUS_BASE(2); -+ pronghorn_pata_resources[0].end = IXP4XX_EXP_BUS_END(2); -+ -+ pronghorn_pata_resources[1].start = IXP4XX_EXP_BUS_BASE(3); -+ pronghorn_pata_resources[1].end = IXP4XX_EXP_BUS_END(3); -+ -+ pronghorn_pata_data.cs0_cfg = IXP4XX_EXP_CS2; -+ pronghorn_pata_data.cs1_cfg = IXP4XX_EXP_CS3; -+ } else { -+ pronghorn_pata_resources[0].start = IXP4XX_EXP_BUS_BASE(3); -+ pronghorn_pata_resources[0].end = IXP4XX_EXP_BUS_END(3); -+ -+ pronghorn_pata_resources[1].start = IXP4XX_EXP_BUS_BASE(4); -+ pronghorn_pata_resources[1].end = IXP4XX_EXP_BUS_END(4); -+ -+ pronghorn_pata_data.cs0_cfg = IXP4XX_EXP_CS3; -+ pronghorn_pata_data.cs1_cfg = IXP4XX_EXP_CS4; -+ -+ platform_device_register(&pronghorn_i2c_gpio); -+ } -+ -+ platform_device_register(&pronghorn_pata); -+} -+ -+MACHINE_START(PRONGHORN, "ADI Engineering Pronghorn") -+ /* Maintainer: Imre Kaloz <kaloz@openwrt.org> */ -+ .phys_io = IXP4XX_PERIPHERAL_BASE_PHYS, -+ .io_pg_offst = ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xfffc, -+ .map_io = ixp4xx_map_io, -+ .init_irq = ixp4xx_init_irq, -+ .timer = &ixp4xx_timer, -+ .boot_params = 0x0100, -+ .init_machine = pronghorn_init, -+MACHINE_END -+ -+MACHINE_START(PRONGHORNMETRO, "ADI Engineering Pronghorn Metro") -+ /* Maintainer: Imre Kaloz <kaloz@openwrt.org> */ -+ .phys_io = IXP4XX_PERIPHERAL_BASE_PHYS, -+ .io_pg_offst = ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xfffc, -+ .map_io = ixp4xx_map_io, -+ .init_irq = ixp4xx_init_irq, -+ .timer = &ixp4xx_timer, -+ .boot_params = 0x0100, -+ .init_machine = pronghorn_init, -+MACHINE_END ---- a/arch/arm/mach-ixp4xx/include/mach/uncompress.h -+++ b/arch/arm/mach-ixp4xx/include/mach/uncompress.h -@@ -41,7 +41,8 @@ static __inline__ void __arch_decomp_set - * Some boards are using UART2 as console - */ - if (machine_is_adi_coyote() || machine_is_gtwx5715() || -- machine_is_gateway7001() || machine_is_wg302v2()) -+ machine_is_gateway7001() || machine_is_wg302v2() || -+ machine_is_pronghorn() || machine_is_pronghorn_metro()) - uart_base = (volatile u32*) IXP4XX_UART2_BASE_PHYS; - else - uart_base = (volatile u32*) IXP4XX_UART1_BASE_PHYS; diff --git a/target/linux/ixp4xx/patches-2.6.33/111-pronghorn_swap_uarts.patch b/target/linux/ixp4xx/patches-2.6.33/111-pronghorn_swap_uarts.patch deleted file mode 100644 index b9fa50768..000000000 --- a/target/linux/ixp4xx/patches-2.6.33/111-pronghorn_swap_uarts.patch +++ /dev/null @@ -1,44 +0,0 @@ ---- a/arch/arm/mach-ixp4xx/pronghorn-setup.c -+++ b/arch/arm/mach-ixp4xx/pronghorn-setup.c -@@ -51,31 +51,31 @@ static struct platform_device pronghorn_ - - static struct resource pronghorn_uart_resources [] = { - { -- .start = IXP4XX_UART1_BASE_PHYS, -- .end = IXP4XX_UART1_BASE_PHYS + 0x0fff, -+ .start = IXP4XX_UART2_BASE_PHYS, -+ .end = IXP4XX_UART2_BASE_PHYS + 0x0fff, - .flags = IORESOURCE_MEM - }, - { -- .start = IXP4XX_UART2_BASE_PHYS, -- .end = IXP4XX_UART2_BASE_PHYS + 0x0fff, -+ .start = IXP4XX_UART1_BASE_PHYS, -+ .end = IXP4XX_UART1_BASE_PHYS + 0x0fff, - .flags = IORESOURCE_MEM - } - }; - - static struct plat_serial8250_port pronghorn_uart_data[] = { - { -- .mapbase = IXP4XX_UART1_BASE_PHYS, -- .membase = (char *)IXP4XX_UART1_BASE_VIRT + REG_OFFSET, -- .irq = IRQ_IXP4XX_UART1, -+ .mapbase = IXP4XX_UART2_BASE_PHYS, -+ .membase = (char *)IXP4XX_UART2_BASE_VIRT + REG_OFFSET, -+ .irq = IRQ_IXP4XX_UART2, - .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST, - .iotype = UPIO_MEM, - .regshift = 2, - .uartclk = IXP4XX_UART_XTAL, - }, - { -- .mapbase = IXP4XX_UART2_BASE_PHYS, -- .membase = (char *)IXP4XX_UART2_BASE_VIRT + REG_OFFSET, -- .irq = IRQ_IXP4XX_UART2, -+ .mapbase = IXP4XX_UART1_BASE_PHYS, -+ .membase = (char *)IXP4XX_UART1_BASE_VIRT + REG_OFFSET, -+ .irq = IRQ_IXP4XX_UART1, - .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST, - .iotype = UPIO_MEM, - .regshift = 2, diff --git a/target/linux/ixp4xx/patches-2.6.33/115-sidewinder_support.patch b/target/linux/ixp4xx/patches-2.6.33/115-sidewinder_support.patch deleted file mode 100644 index bad0826c8..000000000 --- a/target/linux/ixp4xx/patches-2.6.33/115-sidewinder_support.patch +++ /dev/null @@ -1,282 +0,0 @@ -From 60bdaaaf3446b4237566c6e04855186fc7bd766b Mon Sep 17 00:00:00 2001 -From: Imre Kaloz <kaloz@openwrt.org> -Date: Sun, 13 Jul 2008 22:46:45 +0200 -Subject: [PATCH] Add support for the ADI Sidewinder - -Signed-off-by: Imre Kaloz <kaloz@openwrt.org> ---- - arch/arm/mach-ixp4xx/Kconfig | 10 ++- - arch/arm/mach-ixp4xx/Makefile | 2 + - arch/arm/mach-ixp4xx/sidewinder-pci.c | 68 ++++++++++++++ - arch/arm/mach-ixp4xx/sidewinder-setup.c | 151 +++++++++++++++++++++++++++++++ - 4 files changed, 230 insertions(+), 1 deletions(-) - create mode 100644 arch/arm/mach-ixp4xx/sidewinder-pci.c - create mode 100644 arch/arm/mach-ixp4xx/sidewinder-setup.c - ---- a/arch/arm/mach-ixp4xx/Kconfig -+++ b/arch/arm/mach-ixp4xx/Kconfig -@@ -81,6 +81,14 @@ config MACH_PRONGHORN - config MACH_PRONGHORNMETRO - def_bool MACH_PRONGHORN - -+config MACH_SIDEWINDER -+ bool "ADI Sidewinder" -+ select PCI -+ help -+ Say 'Y' here if you want your kernel to support the ADI -+ Engineering Sidewinder board. For more information on this -+ platform, see http://www.adiengineering.com -+ - config ARCH_IXDP425 - bool "IXDP425" - help -@@ -169,7 +177,7 @@ config MACH_FSG - # - config CPU_IXP46X - bool -- depends on MACH_IXDP465 -+ depends on MACH_IXDP465 || MACH_SIDEWINDER - default y - - config CPU_IXP43X ---- a/arch/arm/mach-ixp4xx/Makefile -+++ b/arch/arm/mach-ixp4xx/Makefile -@@ -18,6 +18,7 @@ obj-pci-$(CONFIG_MACH_WG302V1) += wg302 - obj-pci-$(CONFIG_MACH_WG302V2) += wg302v2-pci.o - obj-pci-$(CONFIG_MACH_FSG) += fsg-pci.o - obj-pci-$(CONFIG_MACH_PRONGHORN) += pronghorn-pci.o -+obj-pci-$(CONFIG_MACH_SIDEWINDER) += sidewinder-pci.o - - obj-y += common.o - -@@ -35,6 +36,7 @@ obj-$(CONFIG_MACH_WG302V2) += wg302v2-se - obj-$(CONFIG_MACH_FSG) += fsg-setup.o - obj-$(CONFIG_MACH_GORAMO_MLR) += goramo_mlr.o - obj-$(CONFIG_MACH_PRONGHORN) += pronghorn-setup.o -+obj-$(CONFIG_MACH_SIDEWINDER) += sidewinder-setup.o - - obj-$(CONFIG_PCI) += $(obj-pci-$(CONFIG_PCI)) common-pci.o - obj-$(CONFIG_IXP4XX_QMGR) += ixp4xx_qmgr.o ---- /dev/null -+++ b/arch/arm/mach-ixp4xx/sidewinder-pci.c -@@ -0,0 +1,68 @@ -+/* -+ * arch/arch/mach-ixp4xx/pronghornmetro-pci.c -+ * -+ * PCI setup routines for ADI Engineering Sidewinder -+ * -+ * Copyright (C) 2008 Imre Kaloz <kaloz@openwrt.org> -+ * -+ * based on coyote-pci.c: -+ * Copyright (C) 2002 Jungo Software Technologies. -+ * Copyright (C) 2003 MontaVista Softwrae, Inc. -+ * -+ * Maintainer: Imre Kaloz <kaloz@openwrt.org> -+ * -+ * This program is free software; you can redistribute it and/or modify -+ * it under the terms of the GNU General Public License version 2 as -+ * published by the Free Software Foundation. -+ * -+ */ -+ -+#include <linux/kernel.h> -+#include <linux/pci.h> -+#include <linux/init.h> -+#include <linux/irq.h> -+ -+#include <asm/mach-types.h> -+#include <mach/hardware.h> -+#include <asm/irq.h> -+ -+#include <asm/mach/pci.h> -+ -+void __init sidewinder_pci_preinit(void) -+{ -+ set_irq_type(IRQ_IXP4XX_GPIO11, IRQ_TYPE_LEVEL_LOW); -+ set_irq_type(IRQ_IXP4XX_GPIO10, IRQ_TYPE_LEVEL_LOW); -+ set_irq_type(IRQ_IXP4XX_GPIO9, IRQ_TYPE_LEVEL_LOW); -+ -+ ixp4xx_pci_preinit(); -+} -+ -+static int __init sidewinder_map_irq(struct pci_dev *dev, u8 slot, u8 pin) -+{ -+ if (slot == 1) -+ return IRQ_IXP4XX_GPIO11; -+ else if (slot == 2) -+ return IRQ_IXP4XX_GPIO10; -+ else if (slot == 3) -+ return IRQ_IXP4XX_GPIO9; -+ else -+ return -1; -+} -+ -+struct hw_pci sidewinder_pci __initdata = { -+ .nr_controllers = 1, -+ .preinit = sidewinder_pci_preinit, -+ .swizzle = pci_std_swizzle, -+ .setup = ixp4xx_setup, -+ .scan = ixp4xx_scan_bus, -+ .map_irq = sidewinder_map_irq, -+}; -+ -+int __init sidewinder_pci_init(void) -+{ -+ if (machine_is_sidewinder()) -+ pci_common_init(&sidewinder_pci); -+ return 0; -+} -+ -+subsys_initcall(sidewinder_pci_init); ---- /dev/null -+++ b/arch/arm/mach-ixp4xx/sidewinder-setup.c -@@ -0,0 +1,149 @@ -+/* -+ * arch/arm/mach-ixp4xx/sidewinder-setup.c -+ * -+ * Board setup for the ADI Engineering Sidewinder -+ * -+ * Copyright (C) 2008 Imre Kaloz <Kaloz@openwrt.org> -+ * -+ * based on coyote-setup.c: -+ * Copyright (C) 2003-2005 MontaVista Software, Inc. -+ * -+ * Author: Imre Kaloz <Kaloz@openwrt.org> -+ */ -+ -+#include <linux/kernel.h> -+#include <linux/serial.h> -+#include <linux/serial_8250.h> -+ -+#include <asm/mach-types.h> -+#include <asm/mach/arch.h> -+#include <asm/mach/flash.h> -+ -+static struct flash_platform_data sidewinder_flash_data = { -+ .map_name = "cfi_probe", -+ .width = 2, -+}; -+ -+static struct resource sidewinder_flash_resource = { -+ .flags = IORESOURCE_MEM, -+}; -+ -+static struct platform_device sidewinder_flash = { -+ .name = "IXP4XX-Flash", -+ .id = 0, -+ .dev = { -+ .platform_data = &sidewinder_flash_data, -+ }, -+ .num_resources = 1, -+ .resource = &sidewinder_flash_resource, -+}; -+ -+static struct resource sidewinder_uart_resources[] = { -+ { -+ .start = IXP4XX_UART1_BASE_PHYS, -+ .end = IXP4XX_UART1_BASE_PHYS + 0x0fff, -+ .flags = IORESOURCE_MEM, -+ }, -+ { -+ .start = IXP4XX_UART2_BASE_PHYS, -+ .end = IXP4XX_UART2_BASE_PHYS + 0x0fff, -+ .flags = IORESOURCE_MEM, -+ } -+}; -+ -+static struct plat_serial8250_port sidewinder_uart_data[] = { -+ { -+ .mapbase = IXP4XX_UART1_BASE_PHYS, -+ .membase = (char *)IXP4XX_UART1_BASE_VIRT + REG_OFFSET, -+ .irq = IRQ_IXP4XX_UART1, -+ .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST, -+ .iotype = UPIO_MEM, -+ .regshift = 2, -+ .uartclk = IXP4XX_UART_XTAL, -+ }, -+ { -+ .mapbase = IXP4XX_UART2_BASE_PHYS, -+ .membase = (char *)IXP4XX_UART2_BASE_VIRT + REG_OFFSET, -+ .irq = IRQ_IXP4XX_UART2, -+ .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST, -+ .iotype = UPIO_MEM, -+ .regshift = 2, -+ .uartclk = IXP4XX_UART_XTAL, -+ }, -+ { }, -+}; -+ -+static struct platform_device sidewinder_uart = { -+ .name = "serial8250", -+ .id = PLAT8250_DEV_PLATFORM, -+ .dev = { -+ .platform_data = sidewinder_uart_data, -+ }, -+ .num_resources = ARRAY_SIZE(sidewinder_uart_resources), -+ .resource = sidewinder_uart_resources, -+}; -+ -+static struct eth_plat_info sidewinder_plat_eth[] = { -+ { -+ .phy = 5, -+ .rxq = 3, -+ .txreadyq = 20, -+ }, { -+ .phy = IXP4XX_ETH_PHY_MAX_ADDR, -+ .phy_mask = 0x1e, -+ .rxq = 4, -+ .txreadyq = 21, -+ }, { -+ .phy = 31, -+ .rxq = 2, -+ .txreadyq = 19, -+ } -+}; -+ -+static struct platform_device sidewinder_eth[] = { -+ { -+ .name = "ixp4xx_eth", -+ .id = IXP4XX_ETH_NPEB, -+ .dev.platform_data = sidewinder_plat_eth, -+ }, { -+ .name = "ixp4xx_eth", -+ .id = IXP4XX_ETH_NPEC, -+ .dev.platform_data = sidewinder_plat_eth + 1, -+ }, { -+ .name = "ixp4xx_eth", -+ .id = IXP4XX_ETH_NPEA, -+ .dev.platform_data = sidewinder_plat_eth + 2, -+ } -+}; -+ -+static struct platform_device *sidewinder_devices[] __initdata = { -+ &sidewinder_flash, -+ &sidewinder_uart, -+ &sidewinder_eth[0], -+ &sidewinder_eth[1], -+ &sidewinder_eth[2], -+}; -+ -+static void __init sidewinder_init(void) -+{ -+ ixp4xx_sys_init(); -+ -+ sidewinder_flash_resource.start = IXP4XX_EXP_BUS_BASE(0); -+ sidewinder_flash_resource.end = IXP4XX_EXP_BUS_BASE(0) + SZ_64M - 1; -+ -+ *IXP4XX_EXP_CS0 |= IXP4XX_FLASH_WRITABLE; -+ *IXP4XX_EXP_CS1 = *IXP4XX_EXP_CS0; -+ -+ platform_add_devices(sidewinder_devices, ARRAY_SIZE(sidewinder_devices)); -+} -+ -+MACHINE_START(SIDEWINDER, "ADI Engineering Sidewinder") -+ /* Maintainer: Imre Kaloz <kaloz@openwrt.org> */ -+ .phys_io = IXP4XX_PERIPHERAL_BASE_PHYS, -+ .io_pg_offst = ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xfffc, -+ .map_io = ixp4xx_map_io, -+ .init_irq = ixp4xx_init_irq, -+ .timer = &ixp4xx_timer, -+ .boot_params = 0x0100, -+ .init_machine = sidewinder_init, -+MACHINE_END diff --git a/target/linux/ixp4xx/patches-2.6.33/116-sidewinder_fis_location.patch b/target/linux/ixp4xx/patches-2.6.33/116-sidewinder_fis_location.patch deleted file mode 100644 index 1d0a98398..000000000 --- a/target/linux/ixp4xx/patches-2.6.33/116-sidewinder_fis_location.patch +++ /dev/null @@ -1,30 +0,0 @@ ---- a/drivers/mtd/redboot.c -+++ b/drivers/mtd/redboot.c -@@ -13,6 +13,8 @@ - - #define BOARD_CONFIG_PART "boardconfig" - -+#include <asm/mach-types.h> -+ - struct fis_image_desc { - unsigned char name[16]; // Null terminated name - uint32_t flash_base; // Address within FLASH of image -@@ -30,7 +32,8 @@ struct fis_list { - struct fis_list *next; - }; - --static int directory = CONFIG_MTD_REDBOOT_DIRECTORY_BLOCK; -+int directory = CONFIG_MTD_REDBOOT_DIRECTORY_BLOCK; -+ - module_param(directory, int, 0); - - static inline int redboot_checksum(struct fis_image_desc *img) -@@ -59,6 +62,8 @@ static int parse_redboot_partitions(stru - #ifdef CONFIG_MTD_REDBOOT_PARTS_UNALLOCATED - static char nullstring[] = "unallocated"; - #endif -+ if (machine_is_sidewinder()) -+ directory = -5; - - if ( directory < 0 ) { - offset = master->size + directory * master->erasesize; diff --git a/target/linux/ixp4xx/patches-2.6.33/120-compex_support.patch b/target/linux/ixp4xx/patches-2.6.33/120-compex_support.patch deleted file mode 100644 index 3a26afec6..000000000 --- a/target/linux/ixp4xx/patches-2.6.33/120-compex_support.patch +++ /dev/null @@ -1,212 +0,0 @@ -From 24025a2dcf1248079dd3019fac6ed955252d277f Mon Sep 17 00:00:00 2001 -From: Imre Kaloz <kaloz@openwrt.org> -Date: Mon, 14 Jul 2008 21:56:34 +0200 -Subject: [PATCH] Add support for the Compex WP18 / NP18A boards - -Signed-off-by: Imre Kaloz <kaloz@openwrt.org> ---- - arch/arm/mach-ixp4xx/Kconfig | 8 ++ - arch/arm/mach-ixp4xx/Makefile | 2 + - arch/arm/mach-ixp4xx/compex-setup.c | 136 +++++++++++++++++++++++++++++++++++ - arch/arm/mach-ixp4xx/ixdp425-pci.c | 3 +- - arch/arm/tools/mach-types | 2 +- - 5 files changed, 149 insertions(+), 2 deletions(-) - create mode 100644 arch/arm/mach-ixp4xx/compex-setup.c - ---- a/arch/arm/mach-ixp4xx/Kconfig -+++ b/arch/arm/mach-ixp4xx/Kconfig -@@ -89,6 +89,14 @@ config MACH_SIDEWINDER - Engineering Sidewinder board. For more information on this - platform, see http://www.adiengineering.com - -+config MACH_COMPEX -+ bool "Compex WP18 / NP18A" -+ select PCI -+ help -+ Say 'Y' here if you want your kernel to support Compex' -+ WP18 or NP18A boards. For more information on this -+ platform, see http://www.compex.com.sg/home/OEM/product_ap.htm -+ - config ARCH_IXDP425 - bool "IXDP425" - help ---- a/arch/arm/mach-ixp4xx/Makefile -+++ b/arch/arm/mach-ixp4xx/Makefile -@@ -19,6 +19,7 @@ obj-pci-$(CONFIG_MACH_WG302V2) += wg302 - obj-pci-$(CONFIG_MACH_FSG) += fsg-pci.o - obj-pci-$(CONFIG_MACH_PRONGHORN) += pronghorn-pci.o - obj-pci-$(CONFIG_MACH_SIDEWINDER) += sidewinder-pci.o -+obj-pci-$(CONFIG_MACH_COMPEX) += ixdp425-pci.o - - obj-y += common.o - -@@ -37,6 +38,7 @@ obj-$(CONFIG_MACH_FSG) += fsg-setup.o - obj-$(CONFIG_MACH_GORAMO_MLR) += goramo_mlr.o - obj-$(CONFIG_MACH_PRONGHORN) += pronghorn-setup.o - obj-$(CONFIG_MACH_SIDEWINDER) += sidewinder-setup.o -+obj-$(CONFIG_MACH_COMPEX) += compex-setup.o - - obj-$(CONFIG_PCI) += $(obj-pci-$(CONFIG_PCI)) common-pci.o - obj-$(CONFIG_IXP4XX_QMGR) += ixp4xx_qmgr.o ---- /dev/null -+++ b/arch/arm/mach-ixp4xx/compex-setup.c -@@ -0,0 +1,136 @@ -+/* -+ * arch/arm/mach-ixp4xx/compex-setup.c -+ * -+ * Compex WP18 / NP18A board-setup -+ * -+ * Copyright (C) 2008 Imre Kaloz <Kaloz@openwrt.org> -+ * -+ * based on coyote-setup.c: -+ * Copyright (C) 2003-2005 MontaVista Software, Inc. -+ * -+ * Author: Imre Kaloz <Kaloz@openwrt.org> -+ */ -+ -+#include <linux/kernel.h> -+#include <linux/serial.h> -+#include <linux/serial_8250.h> -+ -+#include <asm/mach-types.h> -+#include <asm/mach/arch.h> -+#include <asm/mach/flash.h> -+ -+static struct flash_platform_data compex_flash_data = { -+ .map_name = "cfi_probe", -+ .width = 2, -+}; -+ -+static struct resource compex_flash_resource = { -+ .flags = IORESOURCE_MEM, -+}; -+ -+static struct platform_device compex_flash = { -+ .name = "IXP4XX-Flash", -+ .id = 0, -+ .dev = { -+ .platform_data = &compex_flash_data, -+ }, -+ .num_resources = 1, -+ .resource = &compex_flash_resource, -+}; -+ -+static struct resource compex_uart_resources[] = { -+ { -+ .start = IXP4XX_UART1_BASE_PHYS, -+ .end = IXP4XX_UART1_BASE_PHYS + 0x0fff, -+ .flags = IORESOURCE_MEM -+ }, -+ { -+ .start = IXP4XX_UART2_BASE_PHYS, -+ .end = IXP4XX_UART2_BASE_PHYS + 0x0fff, -+ .flags = IORESOURCE_MEM -+ } -+}; -+ -+static struct plat_serial8250_port compex_uart_data[] = { -+ { -+ .mapbase = IXP4XX_UART1_BASE_PHYS, -+ .membase = (char *)IXP4XX_UART1_BASE_VIRT + REG_OFFSET, -+ .irq = IRQ_IXP4XX_UART1, -+ .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST, -+ .iotype = UPIO_MEM, -+ .regshift = 2, -+ .uartclk = IXP4XX_UART_XTAL, -+ }, -+ { -+ .mapbase = IXP4XX_UART2_BASE_PHYS, -+ .membase = (char *)IXP4XX_UART2_BASE_VIRT + REG_OFFSET, -+ .irq = IRQ_IXP4XX_UART2, -+ .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST, -+ .iotype = UPIO_MEM, -+ .regshift = 2, -+ .uartclk = IXP4XX_UART_XTAL, -+ }, -+ { }, -+}; -+ -+static struct platform_device compex_uart = { -+ .name = "serial8250", -+ .id = PLAT8250_DEV_PLATFORM, -+ .dev.platform_data = compex_uart_data, -+ .num_resources = 2, -+ .resource = compex_uart_resources, -+}; -+ -+static struct eth_plat_info compex_plat_eth[] = { -+ { -+ .phy = IXP4XX_ETH_PHY_MAX_ADDR, -+ .phy_mask = 0xf0000, -+ .rxq = 3, -+ .txreadyq = 20, -+ }, { -+ .phy = 3, -+ .rxq = 4, -+ .txreadyq = 21, -+ } -+}; -+ -+static struct platform_device compex_eth[] = { -+ { -+ .name = "ixp4xx_eth", -+ .id = IXP4XX_ETH_NPEB, -+ .dev.platform_data = compex_plat_eth, -+ }, { -+ .name = "ixp4xx_eth", -+ .id = IXP4XX_ETH_NPEC, -+ .dev.platform_data = compex_plat_eth + 1, -+ } -+}; -+ -+static struct platform_device *compex_devices[] __initdata = { -+ &compex_flash, -+ &compex_uart, -+ &compex_eth[0], -+ &compex_eth[1], -+}; -+ -+static void __init compex_init(void) -+{ -+ ixp4xx_sys_init(); -+ -+ compex_flash_resource.start = IXP4XX_EXP_BUS_BASE(0); -+ compex_flash_resource.end = -+ IXP4XX_EXP_BUS_BASE(0) + SZ_32M - 1; -+ -+ platform_add_devices(compex_devices, ARRAY_SIZE(compex_devices)); -+} -+ -+MACHINE_START(COMPEX, "Compex WP18 / NP18A") -+ /* Maintainer: Imre Kaloz <Kaloz@openwrt.org> */ -+ .phys_io = IXP4XX_PERIPHERAL_BASE_PHYS, -+ .io_pg_offst = ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xfffc, -+ .map_io = ixp4xx_map_io, -+ .init_irq = ixp4xx_init_irq, -+ .timer = &ixp4xx_timer, -+ .boot_params = 0x0100, -+ .init_machine = compex_init, -+MACHINE_END ---- a/arch/arm/mach-ixp4xx/ixdp425-pci.c -+++ b/arch/arm/mach-ixp4xx/ixdp425-pci.c -@@ -70,7 +70,8 @@ struct hw_pci ixdp425_pci __initdata = { - int __init ixdp425_pci_init(void) - { - if (machine_is_ixdp425() || machine_is_ixcdp1100() || -- machine_is_ixdp465() || machine_is_kixrp435()) -+ machine_is_ixdp465() || machine_is_kixrp435() || -+ machine_is_compex()) - pci_common_init(&ixdp425_pci); - return 0; - } ---- a/arch/arm/tools/mach-types -+++ b/arch/arm/tools/mach-types -@@ -1273,7 +1273,7 @@ oiab MACH_OIAB OIAB 1269 - smdk6400 MACH_SMDK6400 SMDK6400 1270 - nokia_n800 MACH_NOKIA_N800 NOKIA_N800 1271 - greenphone MACH_GREENPHONE GREENPHONE 1272 --compex42x MACH_COMPEXWP18 COMPEXWP18 1273 -+compex MACH_COMPEX COMPEX 1273 - xmate MACH_XMATE XMATE 1274 - energizer MACH_ENERGIZER ENERGIZER 1275 - ime1 MACH_IME1 IME1 1276 diff --git a/target/linux/ixp4xx/patches-2.6.33/130-wrt300nv2_support.patch b/target/linux/ixp4xx/patches-2.6.33/130-wrt300nv2_support.patch deleted file mode 100644 index c184a6c6c..000000000 --- a/target/linux/ixp4xx/patches-2.6.33/130-wrt300nv2_support.patch +++ /dev/null @@ -1,225 +0,0 @@ ---- a/arch/arm/mach-ixp4xx/Kconfig -+++ b/arch/arm/mach-ixp4xx/Kconfig -@@ -97,6 +97,14 @@ config MACH_COMPEX - WP18 or NP18A boards. For more information on this - platform, see http://www.compex.com.sg/home/OEM/product_ap.htm - -+config MACH_WRT300NV2 -+ bool "Linksys WRT300N v2" -+ select PCI -+ help -+ Say 'Y' here if you want your kernel to support Linksys' -+ WRT300N v2 router. For more information on this -+ platform, see http://openwrt.org -+ - config ARCH_IXDP425 - bool "IXDP425" - help ---- a/arch/arm/mach-ixp4xx/Makefile -+++ b/arch/arm/mach-ixp4xx/Makefile -@@ -20,6 +20,7 @@ obj-pci-$(CONFIG_MACH_FSG) += fsg-pci.o - obj-pci-$(CONFIG_MACH_PRONGHORN) += pronghorn-pci.o - obj-pci-$(CONFIG_MACH_SIDEWINDER) += sidewinder-pci.o - obj-pci-$(CONFIG_MACH_COMPEX) += ixdp425-pci.o -+obj-pci-$(CONFIG_MACH_WRT300NV2) += wrt300nv2-pci.o - - obj-y += common.o - -@@ -39,6 +40,7 @@ obj-$(CONFIG_MACH_GORAMO_MLR) += goramo_ - obj-$(CONFIG_MACH_PRONGHORN) += pronghorn-setup.o - obj-$(CONFIG_MACH_SIDEWINDER) += sidewinder-setup.o - obj-$(CONFIG_MACH_COMPEX) += compex-setup.o -+obj-$(CONFIG_MACH_WRT300NV2) += wrt300nv2-setup.o - - obj-$(CONFIG_PCI) += $(obj-pci-$(CONFIG_PCI)) common-pci.o - obj-$(CONFIG_IXP4XX_QMGR) += ixp4xx_qmgr.o ---- /dev/null -+++ b/arch/arm/mach-ixp4xx/wrt300nv2-pci.c -@@ -0,0 +1,65 @@ -+/* -+ * arch/arch/mach-ixp4xx/wrt300nv2-pci.c -+ * -+ * PCI setup routines for Linksys WRT300N v2 -+ * -+ * Copyright (C) 2007 Imre Kaloz <kaloz@openwrt.org> -+ * -+ * based on coyote-pci.c: -+ * Copyright (C) 2002 Jungo Software Technologies. -+ * Copyright (C) 2003 MontaVista Softwrae, Inc. -+ * -+ * Maintainer: Imre Kaloz <kaloz@openwrt.org> -+ * -+ * This program is free software; you can redistribute it and/or modify -+ * it under the terms of the GNU General Public License version 2 as -+ * published by the Free Software Foundation. -+ * -+ */ -+ -+#include <linux/kernel.h> -+#include <linux/pci.h> -+#include <linux/init.h> -+#include <linux/irq.h> -+ -+#include <asm/mach-types.h> -+#include <mach/hardware.h> -+#include <asm/irq.h> -+ -+#include <asm/mach/pci.h> -+ -+extern void ixp4xx_pci_preinit(void); -+extern int ixp4xx_setup(int nr, struct pci_sys_data *sys); -+extern struct pci_bus *ixp4xx_scan_bus(int nr, struct pci_sys_data *sys); -+ -+void __init wrt300nv2_pci_preinit(void) -+{ -+ set_irq_type(IRQ_IXP4XX_GPIO8, IRQ_TYPE_LEVEL_LOW); -+ -+ ixp4xx_pci_preinit(); -+} -+ -+static int __init wrt300nv2_map_irq(struct pci_dev *dev, u8 slot, u8 pin) -+{ -+ if (slot == 1) -+ return IRQ_IXP4XX_GPIO8; -+ else return -1; -+} -+ -+struct hw_pci wrt300nv2_pci __initdata = { -+ .nr_controllers = 1, -+ .preinit = wrt300nv2_pci_preinit, -+ .swizzle = pci_std_swizzle, -+ .setup = ixp4xx_setup, -+ .scan = ixp4xx_scan_bus, -+ .map_irq = wrt300nv2_map_irq, -+}; -+ -+int __init wrt300nv2_pci_init(void) -+{ -+ if (machine_is_wrt300nv2()) -+ pci_common_init(&wrt300nv2_pci); -+ return 0; -+} -+ -+subsys_initcall(wrt300nv2_pci_init); ---- /dev/null -+++ b/arch/arm/mach-ixp4xx/wrt300nv2-setup.c -@@ -0,0 +1,108 @@ -+/* -+ * arch/arm/mach-ixp4xx/wrt300nv2-setup.c -+ * -+ * Board setup for the Linksys WRT300N v2 -+ * -+ * Copyright (C) 2007 Imre Kaloz <Kaloz@openwrt.org> -+ * -+ * based on coyote-setup.c: -+ * Copyright (C) 2003-2005 MontaVista Software, Inc. -+ * -+ * Author: Imre Kaloz <Kaloz@openwrt.org> -+ */ -+ -+#include <linux/kernel.h> -+#include <linux/init.h> -+#include <linux/device.h> -+#include <linux/serial.h> -+#include <linux/tty.h> -+#include <linux/serial_8250.h> -+#include <linux/slab.h> -+ -+#include <asm/types.h> -+#include <asm/setup.h> -+#include <asm/memory.h> -+#include <mach/hardware.h> -+#include <asm/irq.h> -+#include <asm/mach-types.h> -+#include <asm/mach/arch.h> -+#include <asm/mach/flash.h> -+ -+static struct flash_platform_data wrt300nv2_flash_data = { -+ .map_name = "cfi_probe", -+ .width = 2, -+}; -+ -+static struct resource wrt300nv2_flash_resource = { -+ .flags = IORESOURCE_MEM, -+}; -+ -+static struct platform_device wrt300nv2_flash = { -+ .name = "IXP4XX-Flash", -+ .id = 0, -+ .dev = { -+ .platform_data = &wrt300nv2_flash_data, -+ }, -+ .num_resources = 1, -+ .resource = &wrt300nv2_flash_resource, -+}; -+ -+static struct resource wrt300nv2_uart_resource = { -+ .start = IXP4XX_UART2_BASE_PHYS, -+ .end = IXP4XX_UART2_BASE_PHYS + 0x0fff, -+ .flags = IORESOURCE_MEM, -+}; -+ -+static struct plat_serial8250_port wrt300nv2_uart_data[] = { -+ { -+ .mapbase = IXP4XX_UART2_BASE_PHYS, -+ .membase = (char *)IXP4XX_UART2_BASE_VIRT + REG_OFFSET, -+ .irq = IRQ_IXP4XX_UART2, -+ .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST, -+ .iotype = UPIO_MEM, -+ .regshift = 2, -+ .uartclk = IXP4XX_UART_XTAL, -+ }, -+ { }, -+}; -+ -+static struct platform_device wrt300nv2_uart = { -+ .name = "serial8250", -+ .id = PLAT8250_DEV_PLATFORM, -+ .dev = { -+ .platform_data = wrt300nv2_uart_data, -+ }, -+ .num_resources = 1, -+ .resource = &wrt300nv2_uart_resource, -+}; -+ -+static struct platform_device *wrt300nv2_devices[] __initdata = { -+ &wrt300nv2_flash, -+ &wrt300nv2_uart -+}; -+ -+static void __init wrt300nv2_init(void) -+{ -+ ixp4xx_sys_init(); -+ -+ wrt300nv2_flash_resource.start = IXP4XX_EXP_BUS_BASE(0); -+ wrt300nv2_flash_resource.end = IXP4XX_EXP_BUS_BASE(0) + SZ_32M - 1; -+ -+ *IXP4XX_EXP_CS0 |= IXP4XX_FLASH_WRITABLE; -+ *IXP4XX_EXP_CS1 = *IXP4XX_EXP_CS0; -+ -+ platform_add_devices(wrt300nv2_devices, ARRAY_SIZE(wrt300nv2_devices)); -+} -+ -+#ifdef CONFIG_MACH_WRT300NV2 -+MACHINE_START(WRT300NV2, "Linksys WRT300N v2") -+ /* Maintainer: Imre Kaloz <kaloz@openwrt.org> */ -+ .phys_io = IXP4XX_PERIPHERAL_BASE_PHYS, -+ .io_pg_offst = ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xfffc, -+ .map_io = ixp4xx_map_io, -+ .init_irq = ixp4xx_init_irq, -+ .timer = &ixp4xx_timer, -+ .boot_params = 0x0100, -+ .init_machine = wrt300nv2_init, -+MACHINE_END -+#endif ---- a/arch/arm/mach-ixp4xx/include/mach/uncompress.h -+++ b/arch/arm/mach-ixp4xx/include/mach/uncompress.h -@@ -42,7 +42,7 @@ static __inline__ void __arch_decomp_set - */ - if (machine_is_adi_coyote() || machine_is_gtwx5715() || - machine_is_gateway7001() || machine_is_wg302v2() || -- machine_is_pronghorn() || machine_is_pronghorn_metro()) -+ machine_is_pronghorn() || machine_is_pronghorn_metro() || machine_is_wrt300nv2()) - uart_base = (volatile u32*) IXP4XX_UART2_BASE_PHYS; - else - uart_base = (volatile u32*) IXP4XX_UART1_BASE_PHYS; diff --git a/target/linux/ixp4xx/patches-2.6.33/131-wrt300nv2_mac_plat_info.patch b/target/linux/ixp4xx/patches-2.6.33/131-wrt300nv2_mac_plat_info.patch deleted file mode 100644 index 3ab68c4f3..000000000 --- a/target/linux/ixp4xx/patches-2.6.33/131-wrt300nv2_mac_plat_info.patch +++ /dev/null @@ -1,40 +0,0 @@ ---- a/arch/arm/mach-ixp4xx/wrt300nv2-setup.c -+++ b/arch/arm/mach-ixp4xx/wrt300nv2-setup.c -@@ -76,9 +76,36 @@ static struct platform_device wrt300nv2_ - .resource = &wrt300nv2_uart_resource, - }; - -+/* Built-in 10/100 Ethernet MAC interfaces */ -+static struct eth_plat_info wrt300nv2_plat_eth[] = { -+ { -+ .phy = -1, -+ .rxq = 3, -+ .txreadyq = 20, -+ }, { -+ .phy = 1, -+ .rxq = 4, -+ .txreadyq = 21, -+ } -+}; -+ -+static struct platform_device wrt300nv2_eth[] = { -+ { -+ .name = "ixp4xx_eth", -+ .id = IXP4XX_ETH_NPEB, -+ .dev.platform_data = wrt300nv2_plat_eth, -+ }, { -+ .name = "ixp4xx_eth", -+ .id = IXP4XX_ETH_NPEC, -+ .dev.platform_data = wrt300nv2_plat_eth + 1, -+ } -+}; -+ - static struct platform_device *wrt300nv2_devices[] __initdata = { - &wrt300nv2_flash, -- &wrt300nv2_uart -+ &wrt300nv2_uart, -+ &wrt300nv2_eth[0], -+ &wrt300nv2_eth[1], - }; - - static void __init wrt300nv2_init(void) diff --git a/target/linux/ixp4xx/patches-2.6.33/132-wrt300nv2_mac_fix.patch b/target/linux/ixp4xx/patches-2.6.33/132-wrt300nv2_mac_fix.patch deleted file mode 100644 index 381cc5b75..000000000 --- a/target/linux/ixp4xx/patches-2.6.33/132-wrt300nv2_mac_fix.patch +++ /dev/null @@ -1,72 +0,0 @@ ---- a/arch/arm/mach-ixp4xx/wrt300nv2-setup.c -+++ b/arch/arm/mach-ixp4xx/wrt300nv2-setup.c -@@ -3,6 +3,7 @@ - * - * Board setup for the Linksys WRT300N v2 - * -+ * Copyright (C) 2010 Alexandros C. Couloumbis <alex@ozo.com> - * Copyright (C) 2007 Imre Kaloz <Kaloz@openwrt.org> - * - * based on coyote-setup.c: -@@ -18,6 +19,7 @@ - #include <linux/tty.h> - #include <linux/serial_8250.h> - #include <linux/slab.h> -+#include <linux/etherdevice.h> - - #include <asm/types.h> - #include <asm/setup.h> -@@ -79,7 +81,8 @@ static struct platform_device wrt300nv2_ - /* Built-in 10/100 Ethernet MAC interfaces */ - static struct eth_plat_info wrt300nv2_plat_eth[] = { - { -- .phy = -1, -+ .phy = IXP4XX_ETH_PHY_MAX_ADDR, -+ .phy_mask = 0x0F0000, - .rxq = 3, - .txreadyq = 20, - }, { -@@ -110,6 +113,10 @@ static struct platform_device *wrt300nv2 - - static void __init wrt300nv2_init(void) - { -+ uint8_t __iomem *f; -+ int offset = 0; -+ int i; -+ - ixp4xx_sys_init(); - - wrt300nv2_flash_resource.start = IXP4XX_EXP_BUS_BASE(0); -@@ -119,6 +126,32 @@ static void __init wrt300nv2_init(void) - *IXP4XX_EXP_CS1 = *IXP4XX_EXP_CS0; - - platform_add_devices(wrt300nv2_devices, ARRAY_SIZE(wrt300nv2_devices)); -+ -+ f = ioremap(IXP4XX_EXP_BUS_BASE(0), 0x60000); -+ -+ if (f) { -+ for (i = 0; i < 6; i++) { -+#ifdef __ARMEB__ -+ wrt300nv2_plat_eth[0].hwaddr[i] = readb(f + 0x5FFA0 + i); -+ if (i == 5) -+ offset = 1; -+ wrt300nv2_plat_eth[1].hwaddr[i] = (wrt300nv2_plat_eth[0].hwaddr[i] + offset); -+#else -+ wrt300nv2_plat_eth[0].hwaddr[i] = readb(f + 0x5FFA0 + (i^3)); -+ if (i == 5) -+ offset = 1; -+ wrt300nv2_plat_eth[1].hwaddr[i] = (wrt300nv2_plat_eth[0].hwaddr[i] + offset); -+#endif -+ } -+ iounmap(f); -+ } -+ -+ if (!(is_valid_ether_addr(wrt300nv2_plat_eth[0].hwaddr))) -+ random_ether_addr(wrt300nv2_plat_eth[0].hwaddr); -+ if (!(is_valid_ether_addr(wrt300nv2_plat_eth[1].hwaddr))) { -+ memcpy(wrt300nv2_plat_eth[1].hwaddr, wrt300nv2_plat_eth[0].hwaddr, ETH_ALEN); -+ wrt300nv2_plat_eth[1].hwaddr[5] = (wrt300nv2_plat_eth[0].hwaddr[5] + 1); -+ } - } - - #ifdef CONFIG_MACH_WRT300NV2 diff --git a/target/linux/ixp4xx/patches-2.6.33/150-lanready_ap1000_support.patch b/target/linux/ixp4xx/patches-2.6.33/150-lanready_ap1000_support.patch deleted file mode 100644 index 1dd31e70e..000000000 --- a/target/linux/ixp4xx/patches-2.6.33/150-lanready_ap1000_support.patch +++ /dev/null @@ -1,200 +0,0 @@ ---- /dev/null -+++ b/arch/arm/mach-ixp4xx/ap1000-setup.c -@@ -0,0 +1,151 @@ -+/* -+ * arch/arm/mach-ixp4xx/ap1000-setup.c -+ * -+ * Lanready AP-1000 -+ * -+ * Copyright (C) 2007 Imre Kaloz <Kaloz@openwrt.org> -+ * -+ * based on ixdp425-setup.c: -+ * Copyright (C) 2003-2005 MontaVista Software, Inc. -+ * -+ * Author: Imre Kaloz <Kaloz@openwrt.org> -+ */ -+ -+#include <linux/kernel.h> -+#include <linux/init.h> -+#include <linux/device.h> -+#include <linux/serial.h> -+#include <linux/tty.h> -+#include <linux/serial_8250.h> -+#include <linux/slab.h> -+ -+#include <asm/types.h> -+#include <asm/setup.h> -+#include <asm/memory.h> -+#include <mach/hardware.h> -+#include <asm/mach-types.h> -+#include <asm/irq.h> -+#include <asm/mach/arch.h> -+#include <asm/mach/flash.h> -+ -+static struct flash_platform_data ap1000_flash_data = { -+ .map_name = "cfi_probe", -+ .width = 2, -+}; -+ -+static struct resource ap1000_flash_resource = { -+ .flags = IORESOURCE_MEM, -+}; -+ -+static struct platform_device ap1000_flash = { -+ .name = "IXP4XX-Flash", -+ .id = 0, -+ .dev = { -+ .platform_data = &ap1000_flash_data, -+ }, -+ .num_resources = 1, -+ .resource = &ap1000_flash_resource, -+}; -+ -+static struct resource ap1000_uart_resources[] = { -+ { -+ .start = IXP4XX_UART1_BASE_PHYS, -+ .end = IXP4XX_UART1_BASE_PHYS + 0x0fff, -+ .flags = IORESOURCE_MEM -+ }, -+ { -+ .start = IXP4XX_UART2_BASE_PHYS, -+ .end = IXP4XX_UART2_BASE_PHYS + 0x0fff, -+ .flags = IORESOURCE_MEM -+ } -+}; -+ -+static struct plat_serial8250_port ap1000_uart_data[] = { -+ { -+ .mapbase = IXP4XX_UART1_BASE_PHYS, -+ .membase = (char *)IXP4XX_UART1_BASE_VIRT + REG_OFFSET, -+ .irq = IRQ_IXP4XX_UART1, -+ .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST, -+ .iotype = UPIO_MEM, -+ .regshift = 2, -+ .uartclk = IXP4XX_UART_XTAL, -+ }, -+ { -+ .mapbase = IXP4XX_UART2_BASE_PHYS, -+ .membase = (char *)IXP4XX_UART2_BASE_VIRT + REG_OFFSET, -+ .irq = IRQ_IXP4XX_UART2, -+ .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST, -+ .iotype = UPIO_MEM, -+ .regshift = 2, -+ .uartclk = IXP4XX_UART_XTAL, -+ }, -+ { }, -+}; -+ -+static struct platform_device ap1000_uart = { -+ .name = "serial8250", -+ .id = PLAT8250_DEV_PLATFORM, -+ .dev.platform_data = ap1000_uart_data, -+ .num_resources = 2, -+ .resource = ap1000_uart_resources -+}; -+ -+static struct platform_device *ap1000_devices[] __initdata = { -+ &ap1000_flash, -+ &ap1000_uart -+}; -+ -+static char ap1000_mem_fixup[] __initdata = "mem=64M "; -+ -+static void __init ap1000_fixup(struct machine_desc *desc, -+ struct tag *tags, char **cmdline, struct meminfo *mi) -+ -+{ -+ struct tag *t = tags; -+ char *p = *cmdline; -+ -+ /* Find the end of the tags table, taking note of any cmdline tag. */ -+ for (; t->hdr.size; t = tag_next(t)) { -+ if (t->hdr.tag == ATAG_CMDLINE) { -+ p = t->u.cmdline.cmdline; -+ } -+ } -+ -+ /* Overwrite the end of the table with a new cmdline tag. */ -+ t->hdr.tag = ATAG_CMDLINE; -+ t->hdr.size = (sizeof (struct tag_header) + -+ strlen(ap1000_mem_fixup) + strlen(p) + 1 + 4) >> 2; -+ strlcpy(t->u.cmdline.cmdline, ap1000_mem_fixup, COMMAND_LINE_SIZE); -+ strlcpy(t->u.cmdline.cmdline + strlen(ap1000_mem_fixup), p, -+ COMMAND_LINE_SIZE - strlen(ap1000_mem_fixup)); -+ -+ /* Terminate the table. */ -+ t = tag_next(t); -+ t->hdr.tag = ATAG_NONE; -+ t->hdr.size = 0; -+} -+ -+static void __init ap1000_init(void) -+{ -+ ixp4xx_sys_init(); -+ -+ ap1000_flash_resource.start = IXP4XX_EXP_BUS_BASE(0); -+ ap1000_flash_resource.end = -+ IXP4XX_EXP_BUS_BASE(0) + ixp4xx_exp_bus_size - 1; -+ -+ platform_add_devices(ap1000_devices, ARRAY_SIZE(ap1000_devices)); -+} -+ -+#ifdef CONFIG_MACH_AP1000 -+MACHINE_START(AP1000, "Lanready AP-1000") -+ /* Maintainer: Imre Kaloz <Kaloz@openwrt.org> */ -+ .phys_io = IXP4XX_PERIPHERAL_BASE_PHYS, -+ .io_pg_offst = ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xfffc, -+ .fixup = ap1000_fixup, -+ .map_io = ixp4xx_map_io, -+ .init_irq = ixp4xx_init_irq, -+ .timer = &ixp4xx_timer, -+ .boot_params = 0x0100, -+ .init_machine = ap1000_init, -+MACHINE_END -+#endif ---- a/arch/arm/mach-ixp4xx/ixdp425-pci.c -+++ b/arch/arm/mach-ixp4xx/ixdp425-pci.c -@@ -71,7 +71,7 @@ int __init ixdp425_pci_init(void) - { - if (machine_is_ixdp425() || machine_is_ixcdp1100() || - machine_is_ixdp465() || machine_is_kixrp435() || -- machine_is_compex()) -+ machine_is_compex() || machine_is_ap1000()) - pci_common_init(&ixdp425_pci); - return 0; - } ---- a/arch/arm/mach-ixp4xx/Kconfig -+++ b/arch/arm/mach-ixp4xx/Kconfig -@@ -105,6 +105,14 @@ config MACH_WRT300NV2 - WRT300N v2 router. For more information on this - platform, see http://openwrt.org - -+config MACH_AP1000 -+ bool "Lanready AP-1000" -+ select PCI -+ help -+ Say 'Y' here if you want your kernel to support Lanready's -+ AP1000 board. For more information on this -+ platform, see http://openwrt.org -+ - config ARCH_IXDP425 - bool "IXDP425" - help ---- a/arch/arm/mach-ixp4xx/Makefile -+++ b/arch/arm/mach-ixp4xx/Makefile -@@ -21,6 +21,7 @@ obj-pci-$(CONFIG_MACH_PRONGHORN) += pron - obj-pci-$(CONFIG_MACH_SIDEWINDER) += sidewinder-pci.o - obj-pci-$(CONFIG_MACH_COMPEX) += ixdp425-pci.o - obj-pci-$(CONFIG_MACH_WRT300NV2) += wrt300nv2-pci.o -+obj-pci-$(CONFIG_MACH_AP1000) += ixdp425-pci.o - - obj-y += common.o - -@@ -41,6 +42,7 @@ obj-$(CONFIG_MACH_PRONGHORN) += pronghor - obj-$(CONFIG_MACH_SIDEWINDER) += sidewinder-setup.o - obj-$(CONFIG_MACH_COMPEX) += compex-setup.o - obj-$(CONFIG_MACH_WRT300NV2) += wrt300nv2-setup.o -+obj-$(CONFIG_MACH_AP1000) += ap1000-setup.o - - obj-$(CONFIG_PCI) += $(obj-pci-$(CONFIG_PCI)) common-pci.o - obj-$(CONFIG_IXP4XX_QMGR) += ixp4xx_qmgr.o diff --git a/target/linux/ixp4xx/patches-2.6.33/151-lanready_ap1000_mac_plat_info.patch b/target/linux/ixp4xx/patches-2.6.33/151-lanready_ap1000_mac_plat_info.patch deleted file mode 100644 index a1214d567..000000000 --- a/target/linux/ixp4xx/patches-2.6.33/151-lanready_ap1000_mac_plat_info.patch +++ /dev/null @@ -1,41 +0,0 @@ ---- a/arch/arm/mach-ixp4xx/ap1000-setup.c -+++ b/arch/arm/mach-ixp4xx/ap1000-setup.c -@@ -90,9 +90,37 @@ static struct platform_device ap1000_uar - .resource = ap1000_uart_resources - }; - -+/* Built-in 10/100 Ethernet MAC interfaces */ -+static struct eth_plat_info ap1000_plat_eth[] = { -+ { -+ .phy = IXP4XX_ETH_PHY_MAX_ADDR, -+ .phy_mask = 0x1e, -+ .rxq = 3, -+ .txreadyq = 20, -+ }, { -+ .phy = 5, -+ .rxq = 4, -+ .txreadyq = 21, -+ } -+}; -+ -+static struct platform_device ap1000_eth[] = { -+ { -+ .name = "ixp4xx_eth", -+ .id = IXP4XX_ETH_NPEB, -+ .dev.platform_data = ap1000_plat_eth, -+ }, { -+ .name = "ixp4xx_eth", -+ .id = IXP4XX_ETH_NPEC, -+ .dev.platform_data = ap1000_plat_eth + 1, -+ } -+}; -+ - static struct platform_device *ap1000_devices[] __initdata = { - &ap1000_flash, -- &ap1000_uart -+ &ap1000_uart, -+ &ap1000_eth[0], -+ &ap1000_eth[1], - }; - - static char ap1000_mem_fixup[] __initdata = "mem=64M "; diff --git a/target/linux/ixp4xx/patches-2.6.33/162-wg302v1_mem_fixup.patch b/target/linux/ixp4xx/patches-2.6.33/162-wg302v1_mem_fixup.patch deleted file mode 100644 index 684db4475..000000000 --- a/target/linux/ixp4xx/patches-2.6.33/162-wg302v1_mem_fixup.patch +++ /dev/null @@ -1,47 +0,0 @@ ---- a/arch/arm/mach-ixp4xx/wg302v1-setup.c -+++ b/arch/arm/mach-ixp4xx/wg302v1-setup.c -@@ -115,6 +115,36 @@ static struct platform_device *wg302v1_d - &wg302v1_eth[0], - }; - -+static char wg302v1_mem_fixup[] __initdata = "mem=32M "; -+ -+static void __init wg302v1_fixup(struct machine_desc *desc, -+ struct tag *tags, char **cmdline, struct meminfo *mi) -+ -+{ -+ struct tag *t = tags; -+ char *p = *cmdline; -+ -+ /* Find the end of the tags table, taking note of any cmdline tag. */ -+ for (; t->hdr.size; t = tag_next(t)) { -+ if (t->hdr.tag == ATAG_CMDLINE) { -+ p = t->u.cmdline.cmdline; -+ } -+ } -+ -+ /* Overwrite the end of the table with a new cmdline tag. */ -+ t->hdr.tag = ATAG_CMDLINE; -+ t->hdr.size = (sizeof (struct tag_header) + -+ strlen(wg302v1_mem_fixup) + strlen(p) + 1 + 4) >> 2; -+ strlcpy(t->u.cmdline.cmdline, wg302v1_mem_fixup, COMMAND_LINE_SIZE); -+ strlcpy(t->u.cmdline.cmdline + strlen(wg302v1_mem_fixup), p, -+ COMMAND_LINE_SIZE - strlen(wg302v1_mem_fixup)); -+ -+ /* Terminate the table. */ -+ t = tag_next(t); -+ t->hdr.tag = ATAG_NONE; -+ t->hdr.size = 0; -+} -+ - static void __init wg302v1_init(void) - { - ixp4xx_sys_init(); -@@ -133,6 +163,7 @@ MACHINE_START(WG302V1, "Netgear WG302 v1 - /* Maintainer: Imre Kaloz <kaloz@openwrt.org> */ - .phys_io = IXP4XX_PERIPHERAL_BASE_PHYS, - .io_pg_offst = ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xfffc, -+ .fixup = wg302v1_fixup, - .map_io = ixp4xx_map_io, - .init_irq = ixp4xx_init_irq, - .timer = &ixp4xx_timer, diff --git a/target/linux/ixp4xx/patches-2.6.33/170-ixdpg425_mac_plat_info.patch b/target/linux/ixp4xx/patches-2.6.33/170-ixdpg425_mac_plat_info.patch deleted file mode 100644 index 279f4c65f..000000000 --- a/target/linux/ixp4xx/patches-2.6.33/170-ixdpg425_mac_plat_info.patch +++ /dev/null @@ -1,41 +0,0 @@ ---- a/arch/arm/mach-ixp4xx/coyote-setup.c -+++ b/arch/arm/mach-ixp4xx/coyote-setup.c -@@ -82,9 +82,37 @@ static struct platform_device coyote_uar - .resource = &coyote_uart_resource, - }; - -+/* Built-in 10/100 Ethernet MAC interfaces */ -+static struct eth_plat_info ixdpg425_plat_eth[] = { -+ { -+ .phy = 5, -+ .rxq = 3, -+ .txreadyq = 20, -+ }, { -+ .phy = 4, -+ .rxq = 4, -+ .txreadyq = 21, -+ } -+}; -+ -+static struct platform_device ixdpg425_eth[] = { -+ { -+ .name = "ixp4xx_eth", -+ .id = IXP4XX_ETH_NPEB, -+ .dev.platform_data = ixdpg425_plat_eth, -+ }, { -+ .name = "ixp4xx_eth", -+ .id = IXP4XX_ETH_NPEC, -+ .dev.platform_data = ixdpg425_plat_eth + 1, -+ } -+}; -+ -+ - static struct platform_device *coyote_devices[] __initdata = { - &coyote_flash, -- &coyote_uart -+ &coyote_uart, -+ &ixdpg425_eth[0], -+ &ixdpg425_eth[1], - }; - - static void __init coyote_init(void) diff --git a/target/linux/ixp4xx/patches-2.6.33/180-tw5334_support.patch b/target/linux/ixp4xx/patches-2.6.33/180-tw5334_support.patch deleted file mode 100644 index bed2c5dba..000000000 --- a/target/linux/ixp4xx/patches-2.6.33/180-tw5334_support.patch +++ /dev/null @@ -1,285 +0,0 @@ ---- a/arch/arm/mach-ixp4xx/Kconfig -+++ b/arch/arm/mach-ixp4xx/Kconfig -@@ -164,6 +164,14 @@ config ARCH_PRPMC1100 - PrPCM1100 Processor Mezanine Module. For more information on - this platform, see <file:Documentation/arm/IXP4xx>. - -+config MACH_TW5334 -+ bool "Titan Wireless TW-533-4" -+ select PCI -+ help -+ Say 'Y' here if you want your kernel to support the Titan -+ Wireless TW533-4. For more information on this platform, -+ see http://openwrt.org -+ - config MACH_NAS100D - bool - prompt "NAS100D" ---- a/arch/arm/mach-ixp4xx/Makefile -+++ b/arch/arm/mach-ixp4xx/Makefile -@@ -22,6 +22,7 @@ obj-pci-$(CONFIG_MACH_SIDEWINDER) += sid - obj-pci-$(CONFIG_MACH_COMPEX) += ixdp425-pci.o - obj-pci-$(CONFIG_MACH_WRT300NV2) += wrt300nv2-pci.o - obj-pci-$(CONFIG_MACH_AP1000) += ixdp425-pci.o -+obj-pci-$(CONFIG_MACH_TW5334) += tw5334-pci.o - - obj-y += common.o - -@@ -43,6 +44,7 @@ obj-$(CONFIG_MACH_SIDEWINDER) += sidewin - obj-$(CONFIG_MACH_COMPEX) += compex-setup.o - obj-$(CONFIG_MACH_WRT300NV2) += wrt300nv2-setup.o - obj-$(CONFIG_MACH_AP1000) += ap1000-setup.o -+obj-$(CONFIG_MACH_TW5334) += tw5334-setup.o - - obj-$(CONFIG_PCI) += $(obj-pci-$(CONFIG_PCI)) common-pci.o - obj-$(CONFIG_IXP4XX_QMGR) += ixp4xx_qmgr.o ---- /dev/null -+++ b/arch/arm/mach-ixp4xx/tw5334-setup.c -@@ -0,0 +1,163 @@ -+/* -+ * arch/arm/mach-ixp4xx/tw5334-setup.c -+ * -+ * Board setup for the Titan Wireless TW-533-4 -+ * -+ * Copyright (C) 2008 Imre Kaloz <kaloz@openwrt.org> -+ * -+ * based on coyote-setup.c: -+ * Copyright (C) 2003-2005 MontaVista Software, Inc. -+ * -+ * Author: Imre Kaloz <Kaloz@openwrt.org> -+ */ -+ -+#include <linux/if_ether.h> -+#include <linux/kernel.h> -+#include <linux/init.h> -+#include <linux/device.h> -+#include <linux/serial.h> -+#include <linux/tty.h> -+#include <linux/serial_8250.h> -+#include <linux/slab.h> -+ -+#include <asm/types.h> -+#include <asm/setup.h> -+#include <asm/memory.h> -+#include <mach/hardware.h> -+#include <asm/irq.h> -+#include <asm/mach-types.h> -+#include <asm/mach/arch.h> -+#include <asm/mach/flash.h> -+ -+static struct flash_platform_data tw5334_flash_data = { -+ .map_name = "cfi_probe", -+ .width = 2, -+}; -+ -+static struct resource tw5334_flash_resource = { -+ .flags = IORESOURCE_MEM, -+}; -+ -+static struct platform_device tw5334_flash = { -+ .name = "IXP4XX-Flash", -+ .id = 0, -+ .dev = { -+ .platform_data = &tw5334_flash_data, -+ }, -+ .num_resources = 1, -+ .resource = &tw5334_flash_resource, -+}; -+ -+static struct resource tw5334_uart_resource = { -+ .start = IXP4XX_UART2_BASE_PHYS, -+ .end = IXP4XX_UART2_BASE_PHYS + 0x0fff, -+ .flags = IORESOURCE_MEM, -+}; -+ -+static struct plat_serial8250_port tw5334_uart_data[] = { -+ { -+ .mapbase = IXP4XX_UART2_BASE_PHYS, -+ .membase = (char *)IXP4XX_UART2_BASE_VIRT + REG_OFFSET, -+ .irq = IRQ_IXP4XX_UART2, -+ .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST, -+ .iotype = UPIO_MEM, -+ .regshift = 2, -+ .uartclk = IXP4XX_UART_XTAL, -+ }, -+ { }, -+}; -+ -+static struct platform_device tw5334_uart = { -+ .name = "serial8250", -+ .id = PLAT8250_DEV_PLATFORM, -+ .dev = { -+ .platform_data = tw5334_uart_data, -+ }, -+ .num_resources = 1, -+ .resource = &tw5334_uart_resource, -+}; -+ -+/* Built-in 10/100 Ethernet MAC interfaces */ -+static struct eth_plat_info tw5334_plat_eth[] = { -+ { -+ .phy = 0, -+ .rxq = 3, -+ .txreadyq = 20, -+ }, { -+ .phy = 1, -+ .rxq = 4, -+ .txreadyq = 21, -+ } -+}; -+ -+static struct platform_device tw5334_eth[] = { -+ { -+ .name = "ixp4xx_eth", -+ .id = IXP4XX_ETH_NPEB, -+ .dev.platform_data = tw5334_plat_eth, -+ }, { -+ .name = "ixp4xx_eth", -+ .id = IXP4XX_ETH_NPEC, -+ .dev.platform_data = tw5334_plat_eth + 1, -+ } -+}; -+ -+static struct platform_device *tw5334_devices[] __initdata = { -+ &tw5334_flash, -+ &tw5334_uart, -+ &tw5334_eth[0], -+ &tw5334_eth[1], -+}; -+ -+static void __init tw5334_init(void) -+{ -+ uint8_t __iomem *f; -+ int i; -+ -+ ixp4xx_sys_init(); -+ -+ tw5334_flash_resource.start = IXP4XX_EXP_BUS_BASE(0); -+ tw5334_flash_resource.end = IXP4XX_EXP_BUS_BASE(0) + SZ_32M - 1; -+ -+ *IXP4XX_EXP_CS0 |= IXP4XX_FLASH_WRITABLE; -+ *IXP4XX_EXP_CS1 = *IXP4XX_EXP_CS0; -+ -+ platform_add_devices(tw5334_devices, ARRAY_SIZE(tw5334_devices)); -+ -+ /* -+ * Map in a portion of the flash and read the MAC addresses. -+ * Since it is stored in BE in the flash itself, we need to -+ * byteswap it if we're in LE mode. -+ */ -+ f = ioremap(IXP4XX_EXP_BUS_BASE(0), 0x1000000); -+ if (f) { -+ for (i = 0; i < 6; i++) { -+#ifdef __ARMEB__ -+ tw5334_plat_eth[0].hwaddr[i] = readb(f + 0xFC0422 + i); -+ tw5334_plat_eth[1].hwaddr[i] = readb(f + 0xFC043B + i); -+#else -+ tw5334_plat_eth[0].hwaddr[i] = readb(f + 0xFC0422 + (i^3)); -+ tw5334_plat_eth[1].hwaddr[i] = readb(f + 0xFC043B + (i^3)); -+#endif -+ } -+ iounmap(f); -+ } -+ -+ printk(KERN_INFO "TW-533-4: Using MAC address %pM for port 0\n", -+ tw5334_plat_eth[0].hwaddr); -+ printk(KERN_INFO "TW-533-4: Using MAC address %pM for port 1\n", -+ tw5334_plat_eth[1].hwaddr); -+} -+ -+#ifdef CONFIG_MACH_TW5334 -+MACHINE_START(TW5334, "Titan Wireless TW-533-4") -+ /* Maintainer: Imre Kaloz <kaloz@openwrt.org> */ -+ .phys_io = IXP4XX_PERIPHERAL_BASE_PHYS, -+ .io_pg_offst = ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xfffc, -+ .map_io = ixp4xx_map_io, -+ .init_irq = ixp4xx_init_irq, -+ .timer = &ixp4xx_timer, -+ .boot_params = 0x0100, -+ .init_machine = tw5334_init, -+MACHINE_END -+#endif ---- /dev/null -+++ b/arch/arm/mach-ixp4xx/tw5334-pci.c -@@ -0,0 +1,69 @@ -+/* -+ * arch/arch/mach-ixp4xx/tw5334-pci.c -+ * -+ * PCI setup routines for the Titan Wireless TW-533-4 -+ * -+ * Copyright (C) 2008 Imre Kaloz <kaloz@openwrt.org> -+ * -+ * based on coyote-pci.c: -+ * Copyright (C) 2002 Jungo Software Technologies. -+ * Copyright (C) 2003 MontaVista Softwrae, Inc. -+ * -+ * Maintainer: Imre Kaloz <kaloz@openwrt.org> -+ * -+ * This program is free software; you can redistribute it and/or modify -+ * it under the terms of the GNU General Public License version 2 as -+ * published by the Free Software Foundation. -+ * -+ */ -+ -+#include <linux/kernel.h> -+#include <linux/pci.h> -+#include <linux/init.h> -+#include <linux/irq.h> -+ -+#include <asm/mach-types.h> -+#include <mach/hardware.h> -+ -+#include <asm/mach/pci.h> -+ -+void __init tw5334_pci_preinit(void) -+{ -+ set_irq_type(IRQ_IXP4XX_GPIO6, IRQ_TYPE_LEVEL_LOW); -+ set_irq_type(IRQ_IXP4XX_GPIO2, IRQ_TYPE_LEVEL_LOW); -+ set_irq_type(IRQ_IXP4XX_GPIO1, IRQ_TYPE_LEVEL_LOW); -+ set_irq_type(IRQ_IXP4XX_GPIO0, IRQ_TYPE_LEVEL_LOW); -+ -+ ixp4xx_pci_preinit(); -+} -+ -+static int __init tw5334_map_irq(struct pci_dev *dev, u8 slot, u8 pin) -+{ -+ if (slot == 12) -+ return IRQ_IXP4XX_GPIO6; -+ else if (slot == 13) -+ return IRQ_IXP4XX_GPIO2; -+ else if (slot == 14) -+ return IRQ_IXP4XX_GPIO1; -+ else if (slot == 15) -+ return IRQ_IXP4XX_GPIO0; -+ else return -1; -+} -+ -+struct hw_pci tw5334_pci __initdata = { -+ .nr_controllers = 1, -+ .preinit = tw5334_pci_preinit, -+ .swizzle = pci_std_swizzle, -+ .setup = ixp4xx_setup, -+ .scan = ixp4xx_scan_bus, -+ .map_irq = tw5334_map_irq, -+}; -+ -+int __init tw5334_pci_init(void) -+{ -+ if (machine_is_tw5334()) -+ pci_common_init(&tw5334_pci); -+ return 0; -+} -+ -+subsys_initcall(tw5334_pci_init); ---- a/arch/arm/mach-ixp4xx/include/mach/uncompress.h -+++ b/arch/arm/mach-ixp4xx/include/mach/uncompress.h -@@ -42,7 +42,8 @@ static __inline__ void __arch_decomp_set - */ - if (machine_is_adi_coyote() || machine_is_gtwx5715() || - machine_is_gateway7001() || machine_is_wg302v2() || -- machine_is_pronghorn() || machine_is_pronghorn_metro() || machine_is_wrt300nv2()) -+ machine_is_pronghorn() || machine_is_pronghorn_metro() || machine_is_wrt300nv2() || -+ machine_is_tw5334()) - uart_base = (volatile u32*) IXP4XX_UART2_BASE_PHYS; - else - uart_base = (volatile u32*) IXP4XX_UART1_BASE_PHYS; diff --git a/target/linux/ixp4xx/patches-2.6.33/185-mi424wr_support.patch b/target/linux/ixp4xx/patches-2.6.33/185-mi424wr_support.patch deleted file mode 100644 index 1b8ee89c9..000000000 --- a/target/linux/ixp4xx/patches-2.6.33/185-mi424wr_support.patch +++ /dev/null @@ -1,465 +0,0 @@ ---- /dev/null -+++ b/arch/arm/mach-ixp4xx/mi424wr-pci.c -@@ -0,0 +1,71 @@ -+/* -+ * arch/arm/mach-ixp4xx/mi424wr-pci.c -+ * -+ * Actiontec MI424WR board-level PCI initialization -+ * -+ * Copyright (C) 2008 Jose Vasconcellos -+ * -+ * Maintainer: Jose Vasconcellos <jvasco@verizon.net> -+ * -+ * This program is free software; you can redistribute it and/or modify -+ * it under the terms of the GNU General Public License version 2 as -+ * published by the Free Software Foundation. -+ * -+ */ -+ -+#include <linux/kernel.h> -+#include <linux/pci.h> -+#include <linux/init.h> -+#include <linux/irq.h> -+ -+#include <asm/mach-types.h> -+#include <asm/mach/pci.h> -+ -+/* PCI controller GPIO to IRQ pin mappings -+ * This information was obtained from Actiontec's GPL release. -+ * -+ * INTA INTB -+ * SLOT 13 8 6 -+ * SLOT 14 7 8 -+ * SLOT 15 6 7 -+ */ -+ -+void __init mi424wr_pci_preinit(void) -+{ -+ set_irq_type(IRQ_IXP4XX_GPIO6, IRQ_TYPE_LEVEL_LOW); -+ set_irq_type(IRQ_IXP4XX_GPIO7, IRQ_TYPE_LEVEL_LOW); -+ set_irq_type(IRQ_IXP4XX_GPIO8, IRQ_TYPE_LEVEL_LOW); -+ -+ ixp4xx_pci_preinit(); -+} -+ -+static int __init mi424wr_map_irq(struct pci_dev *dev, u8 slot, u8 pin) -+{ -+ if (slot == 13) -+ return IRQ_IXP4XX_GPIO8; -+ if (slot == 14) -+ return IRQ_IXP4XX_GPIO7; -+ if (slot == 15) -+ return IRQ_IXP4XX_GPIO6; -+ -+ return -1; -+} -+ -+struct hw_pci mi424wr_pci __initdata = { -+ .nr_controllers = 1, -+ .preinit = mi424wr_pci_preinit, -+ .swizzle = pci_std_swizzle, -+ .setup = ixp4xx_setup, -+ .scan = ixp4xx_scan_bus, -+ .map_irq = mi424wr_map_irq, -+}; -+ -+int __init mi424wr_pci_init(void) -+{ -+ if (machine_is_mi424wr()) -+ pci_common_init(&mi424wr_pci); -+ return 0; -+} -+ -+subsys_initcall(mi424wr_pci_init); -+ ---- /dev/null -+++ b/arch/arm/mach-ixp4xx/mi424wr-setup.c -@@ -0,0 +1,344 @@ -+/* -+ * arch/arm/mach-ixp4xx/mi424wr-setup.c -+ * -+ * Actiontec MI424-WR board setup -+ * Copyright (c) 2008 Jose Vasconcellos -+ * -+ * Based on Gemtek GTWX5715 by -+ * Copyright (C) 2004 George T. Joseph -+ * Derived from Coyote -+ * -+ * This program is free software; you can redistribute it and/or -+ * modify it under the terms of the GNU General Public License -+ * as published by the Free Software Foundation; either version 2 -+ * of the License, or (at your option) any later version. -+ * -+ * This program is distributed in the hope that it will be useful, -+ * but WITHOUT ANY WARRANTY; without even the implied warranty of -+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -+ * GNU General Public License for more details. -+ * -+ * You should have received a copy of the GNU General Public License -+ * along with this program; if not, write to the Free Software -+ * Foundation, Inc., 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA. -+ * -+ */ -+ -+#include <linux/init.h> -+#include <linux/device.h> -+#include <linux/serial.h> -+#include <linux/serial_8250.h> -+#include <linux/types.h> -+#include <linux/memory.h> -+#include <linux/leds.h> -+#include <linux/spi/spi_gpio_old.h> -+ -+#include <asm/setup.h> -+#include <asm/irq.h> -+#include <asm/io.h> -+#include <asm/mach-types.h> -+#include <asm/mach/arch.h> -+#include <asm/mach/flash.h> -+ -+/* -+ * GPIO 2,3,4 and 9 are hard wired to the Micrel/Kendin KS8995M Switch -+ * and operate as an SPI type interface. The details of the interface -+ * are available on Kendin/Micrel's web site. -+ */ -+ -+#define MI424WR_KSSPI_SELECT 9 -+#define MI424WR_KSSPI_TXD 4 -+#define MI424WR_KSSPI_CLOCK 2 -+#define MI424WR_KSSPI_RXD 3 -+ -+/* -+ * The "reset" button is wired to GPIO 10. -+ * The GPIO is brought "low" when the button is pushed. -+ */ -+ -+#define MI424WR_BUTTON_GPIO 10 -+#define MI424WR_BUTTON_IRQ IRQ_IXP4XX_GPIO10 -+ -+#define MI424WR_MOCA_WAN_LED 11 -+ -+/* Latch on CS1 - taken from Actiontec's 2.4 source code -+ * -+ * default latch value -+ * 0 - power alarm led (red) 0 (off) -+ * 1 - power led (green) 0 (off) -+ * 2 - wireless led (green) 1 (off) -+ * 3 - no internet led (red) 0 (off) -+ * 4 - internet ok led (green) 0 (off) -+ * 5 - moca LAN 0 (off) -+ * 6 - WAN alarm led (red) 0 (off) -+ * 7 - PCI reset 1 (not reset) -+ * 8 - IP phone 1 led (green) 1 (off) -+ * 9 - IP phone 2 led (green) 1 (off) -+ * 10 - VOIP ready led (green) 1 (off) -+ * 11 - PSTN relay 1 control 0 (PSTN) -+ * 12 - PSTN relay 1 control 0 (PSTN) -+ * 13 - N/A -+ * 14 - N/A -+ * 15 - N/A -+ */ -+ -+#define MI424WR_LATCH_MASK 0x04 -+#define MI424WR_LATCH_DEFAULT 0x1f86 -+ -+#define MI424WR_LATCH_ALARM_LED 0x00 -+#define MI424WR_LATCH_POWER_LED 0x01 -+#define MI424WR_LATCH_WIRELESS_LED 0x02 -+#define MI424WR_LATCH_INET_DOWN_LED 0x03 -+#define MI424WR_LATCH_INET_OK_LED 0x04 -+#define MI424WR_LATCH_MOCA_LAN_LED 0x05 -+#define MI424WR_LATCH_WAN_ALARM_LED 0x06 -+#define MI424WR_LATCH_PCI_RESET 0x07 -+#define MI424WR_LATCH_PHONE1_LED 0x08 -+#define MI424WR_LATCH_PHONE2_LED 0x09 -+#define MI424WR_LATCH_VOIP_LED 0x10 -+#define MI424WR_LATCH_PSTN_RELAY1 0x11 -+#define MI424WR_LATCH_PSTN_RELAY2 0x12 -+ -+/* initialize CS1 to default timings, Intel style, 16-bit bus */ -+#define MI424WR_CS1_CONFIG 0x80000002 -+ -+/* Define both UARTs but they are not easily accessible. -+ */ -+ -+static struct resource mi424wr_uart_resources[] = { -+ { -+ .start = IXP4XX_UART1_BASE_PHYS, -+ .end = IXP4XX_UART1_BASE_PHYS + 0x0fff, -+ .flags = IORESOURCE_MEM, -+ }, -+ { -+ .start = IXP4XX_UART2_BASE_PHYS, -+ .end = IXP4XX_UART2_BASE_PHYS + 0x0fff, -+ .flags = IORESOURCE_MEM, -+ } -+}; -+ -+ -+static struct plat_serial8250_port mi424wr_uart_platform_data[] = { -+ { -+ .mapbase = IXP4XX_UART1_BASE_PHYS, -+ .membase = (char *)IXP4XX_UART1_BASE_VIRT + REG_OFFSET, -+ .irq = IRQ_IXP4XX_UART1, -+ .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST, -+ .iotype = UPIO_MEM, -+ .regshift = 2, -+ .uartclk = IXP4XX_UART_XTAL, -+ }, -+ { -+ .mapbase = IXP4XX_UART2_BASE_PHYS, -+ .membase = (char *)IXP4XX_UART2_BASE_VIRT + REG_OFFSET, -+ .irq = IRQ_IXP4XX_UART2, -+ .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST, -+ .iotype = UPIO_MEM, -+ .regshift = 2, -+ .uartclk = IXP4XX_UART_XTAL, -+ }, -+ { }, -+}; -+ -+static struct platform_device mi424wr_uart_device = { -+ .name = "serial8250", -+ .id = PLAT8250_DEV_PLATFORM, -+ .dev.platform_data = mi424wr_uart_platform_data, -+ .num_resources = ARRAY_SIZE(mi424wr_uart_resources), -+ .resource = mi424wr_uart_resources, -+}; -+ -+static struct flash_platform_data mi424wr_flash_data = { -+ .map_name = "cfi_probe", -+ .width = 2, -+}; -+ -+static struct resource mi424wr_flash_resource = { -+ .flags = IORESOURCE_MEM, -+}; -+ -+static struct platform_device mi424wr_flash = { -+ .name = "IXP4XX-Flash", -+ .id = 0, -+ .dev.platform_data = &mi424wr_flash_data, -+ .num_resources = 1, -+ .resource = &mi424wr_flash_resource, -+}; -+ -+static int mi424wr_spi_boardinfo_setup(struct spi_board_info *bi, -+ struct spi_master *master, void *data) -+{ -+ -+ strlcpy(bi->modalias, "spi-ks8995", sizeof(bi->modalias)); -+ -+ bi->max_speed_hz = 5000000 /* Hz */; -+ bi->bus_num = master->bus_num; -+ bi->mode = SPI_MODE_0; -+ -+ return 0; -+} -+ -+static struct spi_gpio_platform_data mi424wr_spi_bus_data = { -+ .pin_cs = MI424WR_KSSPI_SELECT, -+ .pin_clk = MI424WR_KSSPI_CLOCK, -+ .pin_miso = MI424WR_KSSPI_RXD, -+ .pin_mosi = MI424WR_KSSPI_TXD, -+ .cs_activelow = 1, -+ .no_spi_delay = 1, -+ .boardinfo_setup = mi424wr_spi_boardinfo_setup, -+}; -+ -+static struct gpio_led mi424wr_gpio_led[] = { -+ { -+ .name = "moca-wan", /* green led */ -+ .gpio = MI424WR_MOCA_WAN_LED, -+ .active_low = 0, -+ } -+}; -+ -+static struct gpio_led_platform_data mi424wr_gpio_leds_data = { -+ .num_leds = 1, -+ .leds = mi424wr_gpio_led, -+}; -+ -+static struct platform_device mi424wr_gpio_leds = { -+ .name = "leds-gpio", -+ .id = -1, -+ .dev.platform_data = &mi424wr_gpio_leds_data, -+}; -+ -+static uint16_t latch_value = MI424WR_LATCH_DEFAULT; -+static uint16_t __iomem *iobase; -+ -+static void mi424wr_latch_set_led(u8 bit, enum led_brightness value) -+{ -+ -+ if (((MI424WR_LATCH_MASK >> bit) & 1) ^ (value == LED_OFF)) -+ latch_value &= ~(0x1 << bit); -+ else -+ latch_value |= (0x1 << bit); -+ -+ __raw_writew(latch_value, iobase); -+ -+} -+ -+static struct latch_led mi424wr_latch_led[] = { -+ { -+ .name = "power-alarm", -+ .bit = MI424WR_LATCH_ALARM_LED, -+ }, -+ { -+ .name = "power-ok", -+ .bit = MI424WR_LATCH_POWER_LED, -+ }, -+ { -+ .name = "wireless", /* green led */ -+ .bit = MI424WR_LATCH_WIRELESS_LED, -+ }, -+ { -+ .name = "inet-down", /* red led */ -+ .bit = MI424WR_LATCH_INET_DOWN_LED, -+ }, -+ { -+ .name = "inet-up", /* green led */ -+ .bit = MI424WR_LATCH_INET_OK_LED, -+ }, -+ { -+ .name = "moca-lan", /* green led */ -+ .bit = MI424WR_LATCH_MOCA_LAN_LED, -+ }, -+ { -+ .name = "wan-alarm", /* red led */ -+ .bit = MI424WR_LATCH_WAN_ALARM_LED, -+ } -+}; -+ -+static struct latch_led_platform_data mi424wr_latch_leds_data = { -+ .num_leds = ARRAY_SIZE(mi424wr_latch_led), -+ .mem = 0x51000000, -+ .leds = mi424wr_latch_led, -+ .set_led = mi424wr_latch_set_led, -+}; -+ -+static struct platform_device mi424wr_latch_leds = { -+ .name = "leds-latch", -+ .id = -1, -+ .dev.platform_data = &mi424wr_latch_leds_data, -+}; -+ -+static struct platform_device mi424wr_spi_bus = { -+ .name = "spi-gpio", -+ .id = 0, -+ .dev.platform_data = &mi424wr_spi_bus_data, -+}; -+ -+static struct eth_plat_info mi424wr_npeb_data = { -+ .phy = 17, /* KS8721 */ -+ .rxq = 3, -+ .txreadyq = 20, -+}; -+ -+static struct eth_plat_info mi424wr_npec_data = { -+ .phy = IXP4XX_ETH_PHY_MAX_ADDR, -+ .phy_mask = 0x1e, /* ports 1-4 of the KS8995 switch */ -+ .rxq = 4, -+ .txreadyq = 21, -+}; -+ -+static struct platform_device mi424wr_npe_devices[] = { -+ { -+ .name = "ixp4xx_eth", -+ .id = IXP4XX_ETH_NPEC, -+ .dev.platform_data = &mi424wr_npec_data, -+ }, { -+ .name = "ixp4xx_eth", -+ .id = IXP4XX_ETH_NPEB, -+ .dev.platform_data = &mi424wr_npeb_data, -+ } -+}; -+ -+static struct platform_device *mi424wr_devices[] __initdata = { -+ &mi424wr_uart_device, -+ &mi424wr_flash, -+ &mi424wr_gpio_leds, -+ &mi424wr_latch_leds, -+ &mi424wr_spi_bus, -+ &mi424wr_npe_devices[0], -+ &mi424wr_npe_devices[1], -+}; -+ -+static void __init mi424wr_init(void) -+{ -+ ixp4xx_sys_init(); -+ -+ mi424wr_flash_resource.start = IXP4XX_EXP_BUS_BASE(0); -+ mi424wr_flash_resource.end = IXP4XX_EXP_BUS_BASE(0) + SZ_8M - 1; -+ -+ *IXP4XX_EXP_CS0 |= IXP4XX_FLASH_WRITABLE; -+ *IXP4XX_EXP_CS1 = MI424WR_CS1_CONFIG; -+ -+ /* configure button as input -+ */ -+ gpio_line_config(MI424WR_BUTTON_GPIO, IXP4XX_GPIO_IN); -+ -+ /* Initialize LEDs and enables PCI bus. -+ */ -+ iobase = ioremap_nocache(IXP4XX_EXP_BUS_BASE(1), 0x1000); -+ __raw_writew(latch_value, iobase); -+ -+ platform_add_devices(mi424wr_devices, ARRAY_SIZE(mi424wr_devices)); -+} -+ -+ -+MACHINE_START(MI424WR, "Actiontec MI424WR") -+ /* Maintainer: Jose Vasconcellos */ -+ .phys_io = IXP4XX_UART2_BASE_PHYS, -+ .io_pg_offst = ((IXP4XX_UART2_BASE_VIRT) >> 18) & 0xfffc, -+ .map_io = ixp4xx_map_io, -+ .init_irq = ixp4xx_init_irq, -+ .timer = &ixp4xx_timer, -+ .boot_params = 0x0100, -+ .init_machine = mi424wr_init, -+MACHINE_END -+ ---- a/arch/arm/mach-ixp4xx/Makefile -+++ b/arch/arm/mach-ixp4xx/Makefile -@@ -23,6 +23,7 @@ obj-pci-$(CONFIG_MACH_COMPEX) += ixdp42 - obj-pci-$(CONFIG_MACH_WRT300NV2) += wrt300nv2-pci.o - obj-pci-$(CONFIG_MACH_AP1000) += ixdp425-pci.o - obj-pci-$(CONFIG_MACH_TW5334) += tw5334-pci.o -+obj-pci-$(CONFIG_MACH_MI424WR) += mi424wr-pci.o - - obj-y += common.o - -@@ -45,6 +46,7 @@ obj-$(CONFIG_MACH_COMPEX) += compex-setu - obj-$(CONFIG_MACH_WRT300NV2) += wrt300nv2-setup.o - obj-$(CONFIG_MACH_AP1000) += ap1000-setup.o - obj-$(CONFIG_MACH_TW5334) += tw5334-setup.o -+obj-$(CONFIG_MACH_MI424WR) += mi424wr-setup.o - - obj-$(CONFIG_PCI) += $(obj-pci-$(CONFIG_PCI)) common-pci.o - obj-$(CONFIG_IXP4XX_QMGR) += ixp4xx_qmgr.o ---- a/arch/arm/mach-ixp4xx/Kconfig -+++ b/arch/arm/mach-ixp4xx/Kconfig -@@ -235,6 +235,13 @@ config MACH_GTWX5715 - "High Speed" UART is n/c (as far as I can tell) - 20 Pin ARM/Xscale JTAG interface on J2 - -+config MACH_MI424WR -+ bool "Actiontec MI424WR" -+ depends on ARCH_IXP4XX -+ select PCI -+ help -+ Add support for the Actiontec MI424-WR. -+ - comment "IXP4xx Options" - - config IXP4XX_INDIRECT_PCI ---- a/arch/arm/configs/ixp4xx_defconfig -+++ b/arch/arm/configs/ixp4xx_defconfig -@@ -172,6 +172,7 @@ CONFIG_MACH_FSG=y - CONFIG_CPU_IXP46X=y - CONFIG_CPU_IXP43X=y - CONFIG_MACH_GTWX5715=y -+CONFIG_MACH_MI424WR=y - - # - # IXP4xx Options diff --git a/target/linux/ixp4xx/patches-2.6.33/190-cambria_support.patch b/target/linux/ixp4xx/patches-2.6.33/190-cambria_support.patch deleted file mode 100644 index 6753451be..000000000 --- a/target/linux/ixp4xx/patches-2.6.33/190-cambria_support.patch +++ /dev/null @@ -1,553 +0,0 @@ ---- /dev/null -+++ b/arch/arm/mach-ixp4xx/cambria-pci.c -@@ -0,0 +1,74 @@ -+/* -+ * arch/arch/mach-ixp4xx/cambria-pci.c -+ * -+ * PCI setup routines for Gateworks Cambria series -+ * -+ * Copyright (C) 2008 Imre Kaloz <kaloz@openwrt.org> -+ * -+ * based on coyote-pci.c: -+ * Copyright (C) 2002 Jungo Software Technologies. -+ * Copyright (C) 2003 MontaVista Softwrae, Inc. -+ * -+ * Maintainer: Imre Kaloz <kaloz@openwrt.org> -+ * -+ * This program is free software; you can redistribute it and/or modify -+ * it under the terms of the GNU General Public License version 2 as -+ * published by the Free Software Foundation. -+ * -+ */ -+ -+#include <linux/kernel.h> -+#include <linux/pci.h> -+#include <linux/init.h> -+#include <linux/irq.h> -+ -+#include <asm/mach-types.h> -+#include <mach/hardware.h> -+#include <asm/irq.h> -+ -+#include <asm/mach/pci.h> -+ -+extern void ixp4xx_pci_preinit(void); -+extern int ixp4xx_setup(int nr, struct pci_sys_data *sys); -+extern struct pci_bus *ixp4xx_scan_bus(int nr, struct pci_sys_data *sys); -+ -+void __init cambria_pci_preinit(void) -+{ -+ set_irq_type(IRQ_IXP4XX_GPIO11, IRQ_TYPE_LEVEL_LOW); -+ set_irq_type(IRQ_IXP4XX_GPIO10, IRQ_TYPE_LEVEL_LOW); -+ set_irq_type(IRQ_IXP4XX_GPIO9, IRQ_TYPE_LEVEL_LOW); -+ set_irq_type(IRQ_IXP4XX_GPIO8, IRQ_TYPE_LEVEL_LOW); -+ -+ ixp4xx_pci_preinit(); -+} -+ -+static int __init cambria_map_irq(struct pci_dev *dev, u8 slot, u8 pin) -+{ -+ if (slot == 1) -+ return IRQ_IXP4XX_GPIO11; -+ else if (slot == 2) -+ return IRQ_IXP4XX_GPIO10; -+ else if (slot == 3) -+ return IRQ_IXP4XX_GPIO9; -+ else if (slot == 4) -+ return IRQ_IXP4XX_GPIO8; -+ else return -1; -+} -+ -+struct hw_pci cambria_pci __initdata = { -+ .nr_controllers = 1, -+ .preinit = cambria_pci_preinit, -+ .swizzle = pci_std_swizzle, -+ .setup = ixp4xx_setup, -+ .scan = ixp4xx_scan_bus, -+ .map_irq = cambria_map_irq, -+}; -+ -+int __init cambria_pci_init(void) -+{ -+ if (machine_is_cambria()) -+ pci_common_init(&cambria_pci); -+ return 0; -+} -+ -+subsys_initcall(cambria_pci_init); ---- /dev/null -+++ b/arch/arm/mach-ixp4xx/cambria-setup.c -@@ -0,0 +1,429 @@ -+/* -+ * arch/arm/mach-ixp4xx/cambria-setup.c -+ * -+ * Board setup for the Gateworks Cambria series -+ * -+ * Copyright (C) 2008 Imre Kaloz <kaloz@openwrt.org> -+ * -+ * based on coyote-setup.c: -+ * Copyright (C) 2003-2005 MontaVista Software, Inc. -+ * -+ * Author: Imre Kaloz <kaloz@openwrt.org> -+ */ -+ -+#include <linux/device.h> -+#include <linux/i2c.h> -+#include <linux/i2c-gpio.h> -+#include <linux/i2c/at24.h> -+#include <linux/if_ether.h> -+#include <linux/init.h> -+#include <linux/kernel.h> -+#include <linux/leds.h> -+#include <linux/memory.h> -+#include <linux/netdevice.h> -+#include <linux/serial.h> -+#include <linux/serial_8250.h> -+#include <linux/slab.h> -+#include <linux/socket.h> -+#include <linux/types.h> -+#include <linux/tty.h> -+ -+#include <mach/hardware.h> -+#include <asm/irq.h> -+#include <asm/mach-types.h> -+#include <asm/mach/arch.h> -+#include <asm/mach/flash.h> -+#include <asm/setup.h> -+ -+struct cambria_board_info { -+ unsigned char *model; -+ void (*setup)(void); -+}; -+ -+static struct cambria_board_info *cambria_info __initdata; -+ -+static struct flash_platform_data cambria_flash_data = { -+ .map_name = "cfi_probe", -+ .width = 2, -+}; -+ -+static struct resource cambria_flash_resource = { -+ .flags = IORESOURCE_MEM, -+}; -+ -+static struct platform_device cambria_flash = { -+ .name = "IXP4XX-Flash", -+ .id = 0, -+ .dev = { -+ .platform_data = &cambria_flash_data, -+ }, -+ .num_resources = 1, -+ .resource = &cambria_flash_resource, -+}; -+ -+static struct i2c_gpio_platform_data cambria_i2c_gpio_data = { -+ .sda_pin = 7, -+ .scl_pin = 6, -+}; -+ -+static struct platform_device cambria_i2c_gpio = { -+ .name = "i2c-gpio", -+ .id = 0, -+ .dev = { -+ .platform_data = &cambria_i2c_gpio_data, -+ }, -+}; -+ -+static struct eth_plat_info cambria_npec_data = { -+ .phy = 1, -+ .rxq = 4, -+ .txreadyq = 21, -+}; -+ -+static struct eth_plat_info cambria_npea_data = { -+ .phy = 2, -+ .rxq = 2, -+ .txreadyq = 19, -+}; -+ -+static struct platform_device cambria_npec_device = { -+ .name = "ixp4xx_eth", -+ .id = IXP4XX_ETH_NPEC, -+ .dev.platform_data = &cambria_npec_data, -+}; -+ -+static struct platform_device cambria_npea_device = { -+ .name = "ixp4xx_eth", -+ .id = IXP4XX_ETH_NPEA, -+ .dev.platform_data = &cambria_npea_data, -+}; -+ -+static struct resource cambria_uart_resource = { -+ .start = IXP4XX_UART1_BASE_PHYS, -+ .end = IXP4XX_UART1_BASE_PHYS + 0x0fff, -+ .flags = IORESOURCE_MEM, -+}; -+ -+static struct plat_serial8250_port cambria_uart_data[] = { -+ { -+ .mapbase = IXP4XX_UART1_BASE_PHYS, -+ .membase = (char *)IXP4XX_UART1_BASE_VIRT + REG_OFFSET, -+ .irq = IRQ_IXP4XX_UART1, -+ .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST, -+ .iotype = UPIO_MEM, -+ .regshift = 2, -+ .uartclk = IXP4XX_UART_XTAL, -+ }, -+ { }, -+}; -+ -+static struct platform_device cambria_uart = { -+ .name = "serial8250", -+ .id = PLAT8250_DEV_PLATFORM, -+ .dev = { -+ .platform_data = cambria_uart_data, -+ }, -+ .num_resources = 1, -+ .resource = &cambria_uart_resource, -+}; -+ -+static struct resource cambria_pata_resources[] = { -+ { -+ .flags = IORESOURCE_MEM -+ }, -+ { -+ .flags = IORESOURCE_MEM, -+ }, -+ { -+ .name = "intrq", -+ .start = IRQ_IXP4XX_GPIO12, -+ .end = IRQ_IXP4XX_GPIO12, -+ .flags = IORESOURCE_IRQ, -+ }, -+}; -+ -+static struct ixp4xx_pata_data cambria_pata_data = { -+ .cs0_bits = 0xbfff3c03, -+ .cs1_bits = 0xbfff3c03, -+}; -+ -+static struct platform_device cambria_pata = { -+ .name = "pata_ixp4xx_cf", -+ .id = 0, -+ .dev.platform_data = &cambria_pata_data, -+ .num_resources = ARRAY_SIZE(cambria_pata_resources), -+ .resource = cambria_pata_resources, -+}; -+ -+static struct gpio_led cambria_gpio_leds[] = { -+ { -+ .name = "user", /* green led */ -+ .gpio = 5, -+ .active_low = 1, -+ } -+}; -+ -+static struct gpio_led_platform_data cambria_gpio_leds_data = { -+ .num_leds = 1, -+ .leds = cambria_gpio_leds, -+}; -+ -+static struct platform_device cambria_gpio_leds_device = { -+ .name = "leds-gpio", -+ .id = -1, -+ .dev.platform_data = &cambria_gpio_leds_data, -+}; -+ -+static struct latch_led cambria_latch_leds[] = { -+ { -+ .name = "ledA", /* green led */ -+ .bit = 0, -+ }, -+ { -+ .name = "ledB", /* green led */ -+ .bit = 1, -+ }, -+ { -+ .name = "ledC", /* green led */ -+ .bit = 2, -+ }, -+ { -+ .name = "ledD", /* green led */ -+ .bit = 3, -+ }, -+ { -+ .name = "ledE", /* green led */ -+ .bit = 4, -+ }, -+ { -+ .name = "ledF", /* green led */ -+ .bit = 5, -+ }, -+ { -+ .name = "ledG", /* green led */ -+ .bit = 6, -+ }, -+ { -+ .name = "ledH", /* green led */ -+ .bit = 7, -+ } -+}; -+ -+static struct latch_led_platform_data cambria_latch_leds_data = { -+ .num_leds = 8, -+ .leds = cambria_latch_leds, -+ .mem = 0x53F40000, -+}; -+ -+static struct platform_device cambria_latch_leds_device = { -+ .name = "leds-latch", -+ .id = -1, -+ .dev.platform_data = &cambria_latch_leds_data, -+}; -+ -+static struct resource cambria_usb0_resources[] = { -+ { -+ .start = 0xCD000000, -+ .end = 0xCD000300, -+ .flags = IORESOURCE_MEM, -+ }, -+ { -+ .start = 32, -+ .flags = IORESOURCE_IRQ, -+ }, -+}; -+ -+static struct resource cambria_usb1_resources[] = { -+ { -+ .start = 0xCE000000, -+ .end = 0xCE000300, -+ .flags = IORESOURCE_MEM, -+ }, -+ { -+ .start = 33, -+ .flags = IORESOURCE_IRQ, -+ }, -+}; -+ -+static u64 ehci_dma_mask = ~(u32)0; -+ -+static struct platform_device cambria_usb0_device = { -+ .name = "ixp4xx-ehci", -+ .id = 0, -+ .resource = cambria_usb0_resources, -+ .num_resources = ARRAY_SIZE(cambria_usb0_resources), -+ .dev = { -+ .dma_mask = &ehci_dma_mask, -+ .coherent_dma_mask = 0xffffffff, -+ }, -+}; -+ -+static struct platform_device cambria_usb1_device = { -+ .name = "ixp4xx-ehci", -+ .id = 1, -+ .resource = cambria_usb1_resources, -+ .num_resources = ARRAY_SIZE(cambria_usb1_resources), -+ .dev = { -+ .dma_mask = &ehci_dma_mask, -+ .coherent_dma_mask = 0xffffffff, -+ }, -+}; -+ -+static struct platform_device *cambria_devices[] __initdata = { -+ &cambria_i2c_gpio, -+ &cambria_flash, -+ &cambria_uart, -+}; -+ -+static void __init cambria_gw23xx_setup(void) -+{ -+ platform_device_register(&cambria_npec_device); -+ platform_device_register(&cambria_npea_device); -+} -+ -+static void __init cambria_gw2350_setup(void) -+{ -+ platform_device_register(&cambria_npec_device); -+ platform_device_register(&cambria_npea_device); -+ -+ platform_device_register(&cambria_usb0_device); -+ platform_device_register(&cambria_usb1_device); -+ -+ platform_device_register(&cambria_gpio_leds_device); -+} -+ -+static void __init cambria_gw2358_setup(void) -+{ -+ platform_device_register(&cambria_npec_device); -+ platform_device_register(&cambria_npea_device); -+ -+ platform_device_register(&cambria_usb0_device); -+ platform_device_register(&cambria_usb1_device); -+ -+ platform_device_register(&cambria_pata); -+ -+ platform_device_register(&cambria_latch_leds_device); -+} -+ -+static struct cambria_board_info cambria_boards[] __initdata = { -+ { -+ .model = "GW2350", -+ .setup = cambria_gw2350_setup, -+ }, { -+ .model = "GW2358", -+ .setup = cambria_gw2358_setup, -+ } -+}; -+ -+static struct cambria_board_info * __init cambria_find_board_info(char *model) -+{ -+ int i; -+ model[6] = '\0'; -+ -+ for (i = 0; i < ARRAY_SIZE(cambria_boards); i++) { -+ struct cambria_board_info *info = &cambria_boards[i]; -+ if (strcmp(info->model, model) == 0) -+ return info; -+ } -+ -+ return NULL; -+} -+ -+static struct memory_accessor *at24_mem_acc; -+ -+static void at24_setup(struct memory_accessor *mem_acc, void *context) -+{ -+ char mac_addr[ETH_ALEN]; -+ char model[7]; -+ -+ at24_mem_acc = mem_acc; -+ -+ /* Read MAC addresses */ -+ if (at24_mem_acc->read(at24_mem_acc, mac_addr, 0x0, 6) == 6) { -+ memcpy(&cambria_npec_data.hwaddr, mac_addr, ETH_ALEN); -+ } -+ if (at24_mem_acc->read(at24_mem_acc, mac_addr, 0x6, 6) == 6) { -+ memcpy(&cambria_npea_data.hwaddr, mac_addr, ETH_ALEN); -+ } -+ -+ /* Read the first 6 bytes of the model number */ -+ if (at24_mem_acc->read(at24_mem_acc, model, 0x20, 6) == 6) { -+ cambria_info = cambria_find_board_info(model); -+ } -+ -+} -+ -+static struct at24_platform_data cambria_eeprom_info = { -+ .byte_len = 1024, -+ .page_size = 16, -+ .flags = AT24_FLAG_READONLY, -+ .setup = at24_setup, -+}; -+ -+static struct i2c_board_info __initdata cambria_i2c_board_info[] = { -+ { -+ I2C_BOARD_INFO("ds1672", 0x68), -+ }, -+ { -+ I2C_BOARD_INFO("ad7418", 0x28), -+ }, -+ { -+ I2C_BOARD_INFO("24c08", 0x51), -+ .platform_data = &cambria_eeprom_info -+ }, -+}; -+ -+static void __init cambria_init(void) -+{ -+ ixp4xx_sys_init(); -+ -+ cambria_flash_resource.start = IXP4XX_EXP_BUS_BASE(0); -+ cambria_flash_resource.end = IXP4XX_EXP_BUS_BASE(0) + SZ_32M - 1; -+ -+ *IXP4XX_EXP_CS0 |= IXP4XX_FLASH_WRITABLE; -+ *IXP4XX_EXP_CS1 = *IXP4XX_EXP_CS0; -+ -+ platform_add_devices(cambria_devices, ARRAY_SIZE(cambria_devices)); -+ -+ cambria_pata_resources[0].start = 0x53e00000; -+ cambria_pata_resources[0].end = 0x53e3ffff; -+ -+ cambria_pata_resources[1].start = 0x53e40000; -+ cambria_pata_resources[1].end = 0x53e7ffff; -+ -+ cambria_pata_data.cs0_cfg = IXP4XX_EXP_CS3; -+ cambria_pata_data.cs1_cfg = IXP4XX_EXP_CS3; -+ -+ i2c_register_board_info(0, cambria_i2c_board_info, -+ ARRAY_SIZE(cambria_i2c_board_info)); -+} -+ -+static int __init cambria_model_setup(void) -+{ -+ if (!machine_is_cambria()) -+ return 0; -+ -+ if (cambria_info) { -+ printk(KERN_DEBUG "Running on Gateworks Cambria %s\n", -+ cambria_info->model); -+ cambria_info->setup(); -+ } else { -+ printk(KERN_INFO "Unknown/missing Cambria model number" -+ " -- defaults will be used\n"); -+ cambria_gw23xx_setup(); -+ } -+ -+ return 0; -+} -+late_initcall(cambria_model_setup); -+ -+MACHINE_START(CAMBRIA, "Gateworks Cambria series") -+ /* Maintainer: Imre Kaloz <kaloz@openwrt.org> */ -+ .phys_io = IXP4XX_PERIPHERAL_BASE_PHYS, -+ .io_pg_offst = ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xfffc, -+ .map_io = ixp4xx_map_io, -+ .init_irq = ixp4xx_init_irq, -+ .timer = &ixp4xx_timer, -+ .boot_params = 0x0100, -+ .init_machine = cambria_init, -+MACHINE_END ---- a/arch/arm/mach-ixp4xx/Kconfig -+++ b/arch/arm/mach-ixp4xx/Kconfig -@@ -25,6 +25,14 @@ config MACH_AVILA - Avila Network Platform. For more information on this platform, - see <file:Documentation/arm/IXP4xx>. - -+config MACH_CAMBRIA -+ bool "Cambria" -+ select PCI -+ help -+ Say 'Y' here if you want your kernel to support the Gateworks -+ Cambria series. For more information on this platform, -+ see <file:Documentation/arm/IXP4xx>. -+ - config MACH_LOFT - bool "Loft" - depends on MACH_AVILA -@@ -214,7 +222,7 @@ config CPU_IXP46X - - config CPU_IXP43X - bool -- depends on MACH_KIXRP435 -+ depends on MACH_KIXRP435 || MACH_CAMBRIA - default y - - config MACH_GTWX5715 ---- a/arch/arm/mach-ixp4xx/Makefile -+++ b/arch/arm/mach-ixp4xx/Makefile -@@ -7,6 +7,7 @@ obj-pci-n := - - obj-pci-$(CONFIG_ARCH_IXDP4XX) += ixdp425-pci.o - obj-pci-$(CONFIG_MACH_AVILA) += avila-pci.o -+obj-pci-$(CONFIG_MACH_CAMBRIA) += cambria-pci.o - obj-pci-$(CONFIG_MACH_IXDPG425) += ixdpg425-pci.o - obj-pci-$(CONFIG_ARCH_ADI_COYOTE) += coyote-pci.o - obj-pci-$(CONFIG_MACH_GTWX5715) += gtwx5715-pci.o -@@ -29,6 +30,7 @@ obj-y += common.o - - obj-$(CONFIG_ARCH_IXDP4XX) += ixdp425-setup.o - obj-$(CONFIG_MACH_AVILA) += avila-setup.o -+obj-$(CONFIG_MACH_CAMBRIA) += cambria-setup.o - obj-$(CONFIG_MACH_IXDPG425) += coyote-setup.o - obj-$(CONFIG_ARCH_ADI_COYOTE) += coyote-setup.o - obj-$(CONFIG_MACH_GTWX5715) += gtwx5715-setup.o diff --git a/target/linux/ixp4xx/patches-2.6.33/191-cambria_optional_uart.patch b/target/linux/ixp4xx/patches-2.6.33/191-cambria_optional_uart.patch deleted file mode 100644 index 2ebe3e4e3..000000000 --- a/target/linux/ixp4xx/patches-2.6.33/191-cambria_optional_uart.patch +++ /dev/null @@ -1,217 +0,0 @@ ---- a/arch/arm/mach-ixp4xx/cambria-setup.c -+++ b/arch/arm/mach-ixp4xx/cambria-setup.c -@@ -34,6 +34,7 @@ - #include <asm/mach/arch.h> - #include <asm/mach/flash.h> - #include <asm/setup.h> -+#include <linux/irq.h> - - struct cambria_board_info { - unsigned char *model; -@@ -127,6 +128,45 @@ static struct platform_device cambria_ua - .resource = &cambria_uart_resource, - }; - -+static struct resource cambria_optional_uart_resources[] = { -+ { -+ .start = 0x52000000, -+ .end = 0x52000fff, -+ .flags = IORESOURCE_MEM -+ }, -+ { -+ .start = 0x53000000, -+ .end = 0x53000fff, -+ .flags = IORESOURCE_MEM -+ } -+}; -+ -+static struct plat_serial8250_port cambria_optional_uart_data[] = { -+ { -+ .flags = UPF_BOOT_AUTOCONF, -+ .iotype = UPIO_MEM_DELAY, -+ .regshift = 0, -+ .uartclk = 1843200, -+ .rw_delay = 2, -+ }, -+ { -+ .flags = UPF_BOOT_AUTOCONF, -+ .iotype = UPIO_MEM_DELAY, -+ .regshift = 0, -+ .uartclk = 1843200, -+ .rw_delay = 2, -+ }, -+ { }, -+}; -+ -+static struct platform_device cambria_optional_uart = { -+ .name = "serial8250", -+ .id = PLAT8250_DEV_PLATFORM1, -+ .dev.platform_data = cambria_optional_uart_data, -+ .num_resources = 2, -+ .resource = cambria_optional_uart_resources, -+}; -+ - static struct resource cambria_pata_resources[] = { - { - .flags = IORESOURCE_MEM -@@ -283,6 +323,19 @@ static void __init cambria_gw23xx_setup( - - static void __init cambria_gw2350_setup(void) - { -+ *IXP4XX_EXP_CS2 = 0xBFFF3C43; -+ set_irq_type(IRQ_IXP4XX_GPIO3, IRQ_TYPE_EDGE_RISING); -+ cambria_optional_uart_data[0].mapbase = 0x52FF0000; -+ cambria_optional_uart_data[0].membase = (void __iomem *)ioremap(0x52FF0000, 0x0fff); -+ cambria_optional_uart_data[0].irq = IRQ_IXP4XX_GPIO3; -+ -+ *IXP4XX_EXP_CS3 = 0xBFFF3C43; -+ set_irq_type(IRQ_IXP4XX_GPIO4, IRQ_TYPE_EDGE_RISING); -+ cambria_optional_uart_data[1].mapbase = 0x53FF0000; -+ cambria_optional_uart_data[1].membase = (void __iomem *)ioremap(0x53FF0000, 0x0fff); -+ cambria_optional_uart_data[1].irq = IRQ_IXP4XX_GPIO4; -+ -+ platform_device_register(&cambria_optional_uart); - platform_device_register(&cambria_npec_device); - platform_device_register(&cambria_npea_device); - -@@ -294,6 +347,19 @@ static void __init cambria_gw2350_setup( - - static void __init cambria_gw2358_setup(void) - { -+ *IXP4XX_EXP_CS3 = 0xBFFF3C43; -+ set_irq_type(IRQ_IXP4XX_GPIO3, IRQ_TYPE_EDGE_RISING); -+ cambria_optional_uart_data[0].mapbase = 0x53FC0000; -+ cambria_optional_uart_data[0].membase = (void __iomem *)ioremap(0x53FC0000, 0x0fff); -+ cambria_optional_uart_data[0].irq = IRQ_IXP4XX_GPIO3; -+ -+ set_irq_type(IRQ_IXP4XX_GPIO4, IRQ_TYPE_EDGE_RISING); -+ cambria_optional_uart_data[1].mapbase = 0x53F80000; -+ cambria_optional_uart_data[1].membase = (void __iomem *)ioremap(0x53F80000, 0x0fff); -+ cambria_optional_uart_data[1].irq = IRQ_IXP4XX_GPIO4; -+ -+ platform_device_register(&cambria_optional_uart); -+ - platform_device_register(&cambria_npec_device); - platform_device_register(&cambria_npea_device); - ---- a/include/linux/serial_8250.h -+++ b/include/linux/serial_8250.h -@@ -27,6 +27,7 @@ struct plat_serial8250_port { - void *private_data; - unsigned char regshift; /* register shift */ - unsigned char iotype; /* UPIO_* */ -+ unsigned int rw_delay; /* udelay for slower busses IXP4XX Expansion Bus */ - unsigned char hub6; - upf_t flags; /* UPF_* flags */ - unsigned int type; /* If UPF_FIXED_TYPE */ ---- a/include/linux/serial_core.h -+++ b/include/linux/serial_core.h -@@ -288,6 +288,7 @@ struct uart_port { - #define UPIO_TSI (5) /* Tsi108/109 type IO */ - #define UPIO_DWAPB (6) /* DesignWare APB UART */ - #define UPIO_RM9000 (7) /* RM9000 type IO */ -+#define UPIO_MEM_DELAY (8) - - unsigned int read_status_mask; /* driver specific */ - unsigned int ignore_status_mask; /* driver specific */ -@@ -330,6 +331,7 @@ struct uart_port { - - unsigned int mctrl; /* current modem ctrl settings */ - unsigned int timeout; /* character-based timeout */ -+ unsigned int rw_delay; /* udelay for slow busses, IXP4XX Expansion Bus */ - unsigned int type; /* port type */ - const struct uart_ops *ops; - unsigned int custom_divisor; ---- a/drivers/serial/8250.c -+++ b/drivers/serial/8250.c -@@ -409,6 +409,20 @@ static void mem_serial_out(struct uart_p - writeb(value, p->membase + offset); - } - -+static unsigned int memdelay_serial_in(struct uart_port *p, int offset) -+{ -+ struct uart_8250_port *up = (struct uart_8250_port *)p; -+ udelay(up->port.rw_delay); -+ return mem_serial_in(p, offset); -+} -+ -+static void memdelay_serial_out(struct uart_port *p, int offset, int value) -+{ -+ struct uart_8250_port *up = (struct uart_8250_port *)p; -+ udelay(up->port.rw_delay); -+ mem_serial_out(p, offset, value); -+} -+ - static void mem32_serial_out(struct uart_port *p, int offset, int value) - { - offset = map_8250_out_reg(p, offset) << p->regshift; -@@ -502,6 +516,11 @@ static void set_io_from_upio(struct uart - p->serial_out = mem32_serial_out; - break; - -+ case UPIO_MEM_DELAY: -+ p->serial_in = memdelay_serial_in; -+ p->serial_out = memdelay_serial_out; -+ break; -+ - #ifdef CONFIG_SERIAL_8250_AU1X00 - case UPIO_AU: - p->serial_in = au_serial_in; -@@ -534,6 +553,7 @@ serial_out_sync(struct uart_8250_port *u - switch (p->iotype) { - case UPIO_MEM: - case UPIO_MEM32: -+ case UPIO_MEM_DELAY: - #ifdef CONFIG_SERIAL_8250_AU1X00 - case UPIO_AU: - #endif -@@ -2450,6 +2470,7 @@ static int serial8250_request_std_resour - case UPIO_MEM32: - case UPIO_MEM: - case UPIO_DWAPB: -+ case UPIO_MEM_DELAY: - if (!up->port.mapbase) - break; - -@@ -2487,6 +2508,7 @@ static void serial8250_release_std_resou - case UPIO_MEM32: - case UPIO_MEM: - case UPIO_DWAPB: -+ case UPIO_MEM_DELAY: - if (!up->port.mapbase) - break; - -@@ -2964,6 +2986,7 @@ static int __devinit serial8250_probe(st - port.serial_in = p->serial_in; - port.serial_out = p->serial_out; - port.dev = &dev->dev; -+ port.rw_delay = p->rw_delay; - port.irqflags |= irqflag; - ret = serial8250_register_port(&port); - if (ret < 0) { -@@ -3113,6 +3136,7 @@ int serial8250_register_port(struct uart - uart->port.iotype = port->iotype; - uart->port.flags = port->flags | UPF_BOOT_AUTOCONF; - uart->port.mapbase = port->mapbase; -+ uart->port.rw_delay = port->rw_delay; - uart->port.private_data = port->private_data; - if (port->dev) - uart->port.dev = port->dev; ---- a/drivers/serial/serial_core.c -+++ b/drivers/serial/serial_core.c -@@ -2144,6 +2144,7 @@ uart_report_port(struct uart_driver *drv - snprintf(address, sizeof(address), - "I/O 0x%lx offset 0x%x", port->iobase, port->hub6); - break; -+ case UPIO_MEM_DELAY: - case UPIO_MEM: - case UPIO_MEM32: - case UPIO_AU: -@@ -2557,6 +2558,7 @@ int uart_match_port(struct uart_port *po - case UPIO_HUB6: - return (port1->iobase == port2->iobase) && - (port1->hub6 == port2->hub6); -+ case UPIO_MEM_DELAY: - case UPIO_MEM: - case UPIO_MEM32: - case UPIO_AU: diff --git a/target/linux/ixp4xx/patches-2.6.33/192-cambria_gpio_device.patch b/target/linux/ixp4xx/patches-2.6.33/192-cambria_gpio_device.patch deleted file mode 100644 index d785c3a8c..000000000 --- a/target/linux/ixp4xx/patches-2.6.33/192-cambria_gpio_device.patch +++ /dev/null @@ -1,46 +0,0 @@ ---- a/arch/arm/mach-ixp4xx/cambria-setup.c -+++ b/arch/arm/mach-ixp4xx/cambria-setup.c -@@ -214,6 +214,20 @@ static struct platform_device cambria_gp - .dev.platform_data = &cambria_gpio_leds_data, - }; - -+static struct resource cambria_gpio_resources[] = { -+ { -+ .name = "gpio", -+ .flags = 0, -+ }, -+}; -+ -+static struct platform_device cambria_gpio = { -+ .name = "GPIODEV", -+ .id = -1, -+ .num_resources = ARRAY_SIZE(cambria_gpio_resources), -+ .resource = cambria_gpio_resources, -+}; -+ - static struct latch_led cambria_latch_leds[] = { - { - .name = "ledA", /* green led */ -@@ -335,6 +349,11 @@ static void __init cambria_gw2350_setup( - cambria_optional_uart_data[1].membase = (void __iomem *)ioremap(0x53FF0000, 0x0fff); - cambria_optional_uart_data[1].irq = IRQ_IXP4XX_GPIO4; - -+ cambria_gpio_resources[0].start = (1 << 0) | (1 << 1) | (1 << 2) | (1 << 3) | (1 << 4) |\ -+ (1 << 5) | (1 << 8) | (1 << 9) | (1 << 12); -+ cambria_gpio_resources[0].end = cambria_gpio_resources[0].start; -+ -+ platform_device_register(&cambria_gpio); - platform_device_register(&cambria_optional_uart); - platform_device_register(&cambria_npec_device); - platform_device_register(&cambria_npea_device); -@@ -358,6 +377,10 @@ static void __init cambria_gw2358_setup( - cambria_optional_uart_data[1].membase = (void __iomem *)ioremap(0x53F80000, 0x0fff); - cambria_optional_uart_data[1].irq = IRQ_IXP4XX_GPIO4; - -+ cambria_gpio_resources[0].start = (1 << 14); -+ cambria_gpio_resources[0].end = cambria_gpio_resources[0].start; -+ -+ platform_device_register(&cambria_gpio); - platform_device_register(&cambria_optional_uart); - - platform_device_register(&cambria_npec_device); diff --git a/target/linux/ixp4xx/patches-2.6.33/193-cambria_pld_gpio.patch b/target/linux/ixp4xx/patches-2.6.33/193-cambria_pld_gpio.patch deleted file mode 100644 index 299630f17..000000000 --- a/target/linux/ixp4xx/patches-2.6.33/193-cambria_pld_gpio.patch +++ /dev/null @@ -1,107 +0,0 @@ ---- a/arch/arm/mach-ixp4xx/cambria-setup.c -+++ b/arch/arm/mach-ixp4xx/cambria-setup.c -@@ -12,11 +12,14 @@ - */ - - #include <linux/device.h> -+#include <linux/gpio_buttons.h> - #include <linux/i2c.h> - #include <linux/i2c-gpio.h> - #include <linux/i2c/at24.h> -+#include <linux/i2c/gw_i2c_pld.h> - #include <linux/if_ether.h> - #include <linux/init.h> -+#include <linux/input.h> - #include <linux/kernel.h> - #include <linux/leds.h> - #include <linux/memory.h> -@@ -323,6 +326,39 @@ static struct platform_device cambria_us - }, - }; - -+static struct gw_i2c_pld_platform_data gw_i2c_pld_data0 = { -+ .gpio_base = 16, -+ .nr_gpio = 8, -+}; -+ -+static struct gw_i2c_pld_platform_data gw_i2c_pld_data1 = { -+ .gpio_base = 24, -+ .nr_gpio = 2, -+}; -+ -+ -+static struct gpio_button cambria_gpio_buttons[] = { -+ { -+ .desc = "user", -+ .type = EV_KEY, -+ .code = BTN_0, -+ .threshold = 2, -+ .gpio = 25, -+ } -+}; -+ -+static struct gpio_buttons_platform_data cambria_gpio_buttons_data = { -+ .poll_interval = 500, -+ .nbuttons = 1, -+ .buttons = cambria_gpio_buttons, -+}; -+ -+static struct platform_device cambria_gpio_buttons_device = { -+ .name = "gpio-buttons", -+ .id = -1, -+ .dev.platform_data = &cambria_gpio_buttons_data, -+}; -+ - static struct platform_device *cambria_devices[] __initdata = { - &cambria_i2c_gpio, - &cambria_flash, -@@ -331,6 +367,11 @@ static struct platform_device *cambria_d - - static void __init cambria_gw23xx_setup(void) - { -+ cambria_gpio_resources[0].start = (1 << 0) | (1 << 1) | (1 << 2) | (1 << 3) | (1 << 4) |\ -+ (1 << 5) | (1 << 8) | (1 << 9) | (1 << 12); -+ cambria_gpio_resources[0].end = cambria_gpio_resources[0].start; -+ -+ platform_device_register(&cambria_gpio); - platform_device_register(&cambria_npec_device); - platform_device_register(&cambria_npea_device); - } -@@ -377,7 +418,8 @@ static void __init cambria_gw2358_setup( - cambria_optional_uart_data[1].membase = (void __iomem *)ioremap(0x53F80000, 0x0fff); - cambria_optional_uart_data[1].irq = IRQ_IXP4XX_GPIO4; - -- cambria_gpio_resources[0].start = (1 << 14); -+ cambria_gpio_resources[0].start = (1 << 14) | (1 << 16) | (1 << 17) | (1 << 18) |\ -+ (1 << 19) | (1 << 20) | (1 << 24) | (1 << 25); - cambria_gpio_resources[0].end = cambria_gpio_resources[0].start; - - platform_device_register(&cambria_gpio); -@@ -391,7 +433,12 @@ static void __init cambria_gw2358_setup( - - platform_device_register(&cambria_pata); - -+ cambria_gpio_leds[0].gpio = 24; -+ platform_device_register(&cambria_gpio_leds_device); -+ - platform_device_register(&cambria_latch_leds_device); -+ -+ platform_device_register(&cambria_gpio_buttons_device); - } - - static struct cambria_board_info cambria_boards[] __initdata = { -@@ -460,6 +507,14 @@ static struct i2c_board_info __initdata - I2C_BOARD_INFO("24c08", 0x51), - .platform_data = &cambria_eeprom_info - }, -+ { -+ I2C_BOARD_INFO("gw_i2c_pld", 0x56), -+ .platform_data = &gw_i2c_pld_data0, -+ }, -+ { -+ I2C_BOARD_INFO("gw_i2c_pld", 0x57), -+ .platform_data = &gw_i2c_pld_data1, -+ }, - }; - - static void __init cambria_init(void) diff --git a/target/linux/ixp4xx/patches-2.6.33/201-npe_driver_print_license_location.patch b/target/linux/ixp4xx/patches-2.6.33/201-npe_driver_print_license_location.patch deleted file mode 100644 index b97dd77dc..000000000 --- a/target/linux/ixp4xx/patches-2.6.33/201-npe_driver_print_license_location.patch +++ /dev/null @@ -1,11 +0,0 @@ ---- a/arch/arm/mach-ixp4xx/ixp4xx_npe.c -+++ b/arch/arm/mach-ixp4xx/ixp4xx_npe.c -@@ -583,6 +583,8 @@ int npe_load_firmware(struct npe *npe, c - npe_reset(npe); - #endif - -+ print_npe(KERN_INFO, npe, "firmware's license can be found in /usr/share/doc/LICENSE.IPL\n"); -+ - print_npe(KERN_INFO, npe, "firmware functionality 0x%X, " - "revision 0x%X:%X\n", (image->id >> 16) & 0xFF, - (image->id >> 8) & 0xFF, image->id & 0xFF); diff --git a/target/linux/ixp4xx/patches-2.6.33/203-npe_driver_mask_phy_features.patch b/target/linux/ixp4xx/patches-2.6.33/203-npe_driver_mask_phy_features.patch deleted file mode 100644 index eacf35d07..000000000 --- a/target/linux/ixp4xx/patches-2.6.33/203-npe_driver_mask_phy_features.patch +++ /dev/null @@ -1,13 +0,0 @@ ---- a/drivers/net/arm/ixp4xx_eth.c -+++ b/drivers/net/arm/ixp4xx_eth.c -@@ -1217,6 +1217,10 @@ static int __devinit eth_init_one(struct - if ((err = IS_ERR(port->phydev))) - goto err_free_mem; - -+ /* mask with MAC supported features */ -+ port->phydev->supported &= PHY_BASIC_FEATURES; -+ port->phydev->advertising = port->phydev->supported; -+ - port->phydev->irq = PHY_POLL; - - if ((err = register_netdev(dev))) diff --git a/target/linux/ixp4xx/patches-2.6.33/205-npe_driver_separate_phy_functions.patch b/target/linux/ixp4xx/patches-2.6.33/205-npe_driver_separate_phy_functions.patch deleted file mode 100644 index 9b8faeb2c..000000000 --- a/target/linux/ixp4xx/patches-2.6.33/205-npe_driver_separate_phy_functions.patch +++ /dev/null @@ -1,119 +0,0 @@ ---- a/drivers/net/arm/ixp4xx_eth.c -+++ b/drivers/net/arm/ixp4xx_eth.c -@@ -396,6 +396,50 @@ static void ixp4xx_adjust_link(struct ne - dev->name, port->speed, port->duplex ? "full" : "half"); - } - -+static int ixp4xx_phy_connect(struct net_device *dev) -+{ -+ struct port *port = netdev_priv(dev); -+ struct eth_plat_info *plat = port->plat; -+ char phy_id[MII_BUS_ID_SIZE + 3]; -+ -+ snprintf(phy_id, MII_BUS_ID_SIZE + 3, PHY_ID_FMT, "0", plat->phy); -+ port->phydev = phy_connect(dev, phy_id, &ixp4xx_adjust_link, 0, -+ PHY_INTERFACE_MODE_MII); -+ if (IS_ERR(port->phydev)) { -+ printk(KERN_ERR "%s: Could not attach to PHY\n", dev->name); -+ return PTR_ERR(port->phydev); -+ } -+ -+ /* mask with MAC supported features */ -+ port->phydev->supported &= PHY_BASIC_FEATURES; -+ port->phydev->advertising = port->phydev->supported; -+ -+ port->phydev->irq = PHY_POLL; -+ -+ return 0; -+} -+ -+static void ixp4xx_phy_disconnect(struct net_device *dev) -+{ -+ struct port *port = netdev_priv(dev); -+ -+ phy_disconnect(port->phydev); -+} -+ -+static void ixp4xx_phy_start(struct net_device *dev) -+{ -+ struct port *port = netdev_priv(dev); -+ -+ port->speed = 0; /* force "link up" message */ -+ phy_start(port->phydev); -+} -+ -+static void ixp4xx_phy_stop(struct net_device *dev) -+{ -+ struct port *port = netdev_priv(dev); -+ -+ phy_stop(port->phydev); -+} - - static inline void debug_pkt(struct net_device *dev, const char *func, - u8 *data, int len) -@@ -1005,8 +1049,7 @@ static int eth_open(struct net_device *d - return err; - } - -- port->speed = 0; /* force "link up" message */ -- phy_start(port->phydev); -+ ixp4xx_phy_start(dev); - - for (i = 0; i < ETH_ALEN; i++) - __raw_writel(dev->dev_addr[i], &port->regs->hw_addr[i]); -@@ -1127,7 +1170,7 @@ static int eth_close(struct net_device * - printk(KERN_CRIT "%s: unable to disable loopback\n", - dev->name); - -- phy_stop(port->phydev); -+ ixp4xx_phy_stop(dev); - - if (!ports_open) - qmgr_disable_irq(TXDONE_QUEUE); -@@ -1153,7 +1196,6 @@ static int __devinit eth_init_one(struct - struct net_device *dev; - struct eth_plat_info *plat = pdev->dev.platform_data; - u32 regs_phys; -- char phy_id[MII_BUS_ID_SIZE + 3]; - int err; - - if (!(dev = alloc_etherdev(sizeof(struct port)))) -@@ -1211,18 +1253,10 @@ static int __devinit eth_init_one(struct - __raw_writel(DEFAULT_CORE_CNTRL, &port->regs->core_control); - udelay(50); - -- snprintf(phy_id, MII_BUS_ID_SIZE + 3, PHY_ID_FMT, "0", plat->phy); -- port->phydev = phy_connect(dev, phy_id, &ixp4xx_adjust_link, 0, -- PHY_INTERFACE_MODE_MII); -- if ((err = IS_ERR(port->phydev))) -+ err = ixp4xx_phy_connect(dev); -+ if (err) - goto err_free_mem; - -- /* mask with MAC supported features */ -- port->phydev->supported &= PHY_BASIC_FEATURES; -- port->phydev->advertising = port->phydev->supported; -- -- port->phydev->irq = PHY_POLL; -- - if ((err = register_netdev(dev))) - goto err_phy_dis; - -@@ -1232,7 +1266,7 @@ static int __devinit eth_init_one(struct - return 0; - - err_phy_dis: -- phy_disconnect(port->phydev); -+ ixp4xx_phy_disconnect(dev); - err_free_mem: - npe_port_tab[NPE_ID(port->id)] = NULL; - platform_set_drvdata(pdev, NULL); -@@ -1250,7 +1284,7 @@ static int __devexit eth_remove_one(stru - struct port *port = netdev_priv(dev); - - unregister_netdev(dev); -- phy_disconnect(port->phydev); -+ ixp4xx_phy_disconnect(dev); - npe_port_tab[NPE_ID(port->id)] = NULL; - platform_set_drvdata(pdev, NULL); - npe_release(port->npe); diff --git a/target/linux/ixp4xx/patches-2.6.33/206-npe_driver_add_update_link_function.patch b/target/linux/ixp4xx/patches-2.6.33/206-npe_driver_add_update_link_function.patch deleted file mode 100644 index 419ec4cdb..000000000 --- a/target/linux/ixp4xx/patches-2.6.33/206-npe_driver_add_update_link_function.patch +++ /dev/null @@ -1,98 +0,0 @@ ---- a/drivers/net/arm/ixp4xx_eth.c -+++ b/drivers/net/arm/ixp4xx_eth.c -@@ -168,7 +168,7 @@ struct port { - struct desc *desc_tab; /* coherent */ - u32 desc_tab_phys; - int id; /* logical port ID */ -- int speed, duplex; -+ int link, speed, duplex; - u8 firmware[4]; - }; - -@@ -365,37 +365,52 @@ static void ixp4xx_mdio_remove(void) - mdiobus_free(mdio_bus); - } - -- --static void ixp4xx_adjust_link(struct net_device *dev) -+static void ixp4xx_update_link(struct net_device *dev) - { - struct port *port = netdev_priv(dev); -- struct phy_device *phydev = port->phydev; - -- if (!phydev->link) { -- if (port->speed) { -- port->speed = 0; -- printk(KERN_INFO "%s: link down\n", dev->name); -- } -+ if (!port->link) { -+ netif_carrier_off(dev); -+ printk(KERN_INFO "%s: link down\n", dev->name); - return; - } - -- if (port->speed == phydev->speed && port->duplex == phydev->duplex) -- return; -- -- port->speed = phydev->speed; -- port->duplex = phydev->duplex; -- -- if (port->duplex) -+ if (port->duplex == DUPLEX_FULL) - __raw_writel(DEFAULT_TX_CNTRL0 & ~TX_CNTRL0_HALFDUPLEX, - &port->regs->tx_control[0]); - else - __raw_writel(DEFAULT_TX_CNTRL0 | TX_CNTRL0_HALFDUPLEX, - &port->regs->tx_control[0]); - -+ netif_carrier_on(dev); - printk(KERN_INFO "%s: link up, speed %u Mb/s, %s duplex\n", - dev->name, port->speed, port->duplex ? "full" : "half"); - } - -+static void ixp4xx_adjust_link(struct net_device *dev) -+{ -+ struct port *port = netdev_priv(dev); -+ struct phy_device *phydev = port->phydev; -+ int status_change = 0; -+ -+ if (phydev->link) { -+ if (port->duplex != phydev->duplex -+ || port->speed != phydev->speed) { -+ status_change = 1; -+ } -+ } -+ -+ if (phydev->link != port->link) -+ status_change = 1; -+ -+ port->link = phydev->link; -+ port->speed = phydev->speed; -+ port->duplex = phydev->duplex; -+ -+ if (status_change) -+ ixp4xx_update_link(dev); -+} -+ - static int ixp4xx_phy_connect(struct net_device *dev) - { - struct port *port = netdev_priv(dev); -@@ -430,7 +445,6 @@ static void ixp4xx_phy_start(struct net_ - { - struct port *port = netdev_priv(dev); - -- port->speed = 0; /* force "link up" message */ - phy_start(port->phydev); - } - -@@ -1260,6 +1274,10 @@ static int __devinit eth_init_one(struct - if ((err = register_netdev(dev))) - goto err_phy_dis; - -+ port->link = 0; -+ port->speed = 0; -+ port->duplex = -1; -+ - printk(KERN_INFO "%s: MII PHY %i on %s\n", dev->name, plat->phy, - npe_name(port->npe)); - diff --git a/target/linux/ixp4xx/patches-2.6.33/207-npe_driver_multiphy_support.patch b/target/linux/ixp4xx/patches-2.6.33/207-npe_driver_multiphy_support.patch deleted file mode 100644 index afcf7e156..000000000 --- a/target/linux/ixp4xx/patches-2.6.33/207-npe_driver_multiphy_support.patch +++ /dev/null @@ -1,155 +0,0 @@ -TODO: take care of additional PHYs through the PHY abstraction layer - ---- a/arch/arm/mach-ixp4xx/include/mach/platform.h -+++ b/arch/arm/mach-ixp4xx/include/mach/platform.h -@@ -72,7 +72,7 @@ extern unsigned long ixp4xx_exp_bus_size - /* - * Clock Speed Definitions. - */ --#define IXP4XX_PERIPHERAL_BUS_CLOCK (66) /* 66Mhzi APB BUS */ -+#define IXP4XX_PERIPHERAL_BUS_CLOCK (66) /* 66Mhzi APB BUS */ - #define IXP4XX_UART_XTAL 14745600 - - /* -@@ -95,12 +95,23 @@ struct sys_timer; - #define IXP4XX_ETH_NPEB 0x10 - #define IXP4XX_ETH_NPEC 0x20 - -+#define IXP4XX_ETH_PHY_MAX_ADDR 32 -+ - /* Information about built-in Ethernet MAC interfaces */ - struct eth_plat_info { - u8 phy; /* MII PHY ID, 0 - 31 */ - u8 rxq; /* configurable, currently 0 - 31 only */ - u8 txreadyq; - u8 hwaddr[6]; -+ -+ u32 phy_mask; -+#if 0 -+ int speed; -+ int duplex; -+#else -+ int speed_10; -+ int half_duplex; -+#endif - }; - - /* Information about built-in HSS (synchronous serial) interfaces */ ---- a/drivers/net/arm/ixp4xx_eth.c -+++ b/drivers/net/arm/ixp4xx_eth.c -@@ -417,6 +417,37 @@ static int ixp4xx_phy_connect(struct net - struct eth_plat_info *plat = port->plat; - char phy_id[MII_BUS_ID_SIZE + 3]; - -+ if (plat->phy == IXP4XX_ETH_PHY_MAX_ADDR) { -+#if 0 -+ switch (plat->speed) { -+ case SPEED_10: -+ case SPEED_100: -+ break; -+ default: -+ printk(KERN_ERR "%s: invalid speed (%d)\n", -+ dev->name, plat->speed); -+ return -EINVAL; -+ } -+ -+ switch (plat->duplex) { -+ case DUPLEX_HALF: -+ case DUPLEX_FULL: -+ break; -+ default: -+ printk(KERN_ERR "%s: invalid duplex mode (%d)\n", -+ dev->name, plat->duplex); -+ return -EINVAL; -+ } -+ port->speed = plat->speed; -+ port->duplex = plat->duplex; -+#else -+ port->speed = plat->speed_10 ? SPEED_10 : SPEED_100; -+ port->duplex = plat->half_duplex ? DUPLEX_HALF : DUPLEX_FULL; -+#endif -+ -+ return 0; -+ } -+ - snprintf(phy_id, MII_BUS_ID_SIZE + 3, PHY_ID_FMT, "0", plat->phy); - port->phydev = phy_connect(dev, phy_id, &ixp4xx_adjust_link, 0, - PHY_INTERFACE_MODE_MII); -@@ -438,21 +469,32 @@ static void ixp4xx_phy_disconnect(struct - { - struct port *port = netdev_priv(dev); - -- phy_disconnect(port->phydev); -+ if (port->phydev) -+ phy_disconnect(port->phydev); - } - - static void ixp4xx_phy_start(struct net_device *dev) - { - struct port *port = netdev_priv(dev); - -- phy_start(port->phydev); -+ if (port->phydev) { -+ phy_start(port->phydev); -+ } else { -+ port->link = 1; -+ ixp4xx_update_link(dev); -+ } - } - - static void ixp4xx_phy_stop(struct net_device *dev) - { - struct port *port = netdev_priv(dev); - -- phy_stop(port->phydev); -+ if (port->phydev) { -+ phy_stop(port->phydev); -+ } else { -+ port->link = 0; -+ ixp4xx_update_link(dev); -+ } - } - - static inline void debug_pkt(struct net_device *dev, const char *func, -@@ -826,6 +868,10 @@ static int eth_ioctl(struct net_device * - - if (!netif_running(dev)) - return -EINVAL; -+ -+ if (!port->phydev) -+ return -EOPNOTSUPP; -+ - return phy_mii_ioctl(port->phydev, if_mii(req), cmd); - } - -@@ -845,18 +891,30 @@ static void ixp4xx_get_drvinfo(struct ne - static int ixp4xx_get_settings(struct net_device *dev, struct ethtool_cmd *cmd) - { - struct port *port = netdev_priv(dev); -+ -+ if (!port->phydev) -+ return -EOPNOTSUPP; -+ - return phy_ethtool_gset(port->phydev, cmd); - } - - static int ixp4xx_set_settings(struct net_device *dev, struct ethtool_cmd *cmd) - { - struct port *port = netdev_priv(dev); -+ -+ if (!port->phydev) -+ return -EOPNOTSUPP; -+ - return phy_ethtool_sset(port->phydev, cmd); - } - - static int ixp4xx_nway_reset(struct net_device *dev) - { - struct port *port = netdev_priv(dev); -+ -+ if (!port->phydev) -+ return -EOPNOTSUPP; -+ - return phy_start_aneg(port->phydev); - } - diff --git a/target/linux/ixp4xx/patches-2.6.33/295-latch_led_driver.patch b/target/linux/ixp4xx/patches-2.6.33/295-latch_led_driver.patch deleted file mode 100644 index e173ac6e4..000000000 --- a/target/linux/ixp4xx/patches-2.6.33/295-latch_led_driver.patch +++ /dev/null @@ -1,201 +0,0 @@ ---- a/drivers/leds/Kconfig -+++ b/drivers/leds/Kconfig -@@ -157,6 +157,13 @@ config LEDS_LP3944 - To compile this driver as a module, choose M here: the - module will be called leds-lp3944. - -+config LEDS_LATCH -+ tristate "LED Support for Memory Latched LEDs" -+ depends on LEDS_CLASS -+ help -+ -- To Do -- -+ -+ - config LEDS_CLEVO_MAIL - tristate "Mail LED on Clevo notebook" - depends on LEDS_CLASS && X86 && SERIO_I8042 && DMI ---- /dev/null -+++ b/drivers/leds/leds-latch.c -@@ -0,0 +1,150 @@ -+/* -+ * LEDs driver for Memory Latched Devices -+ * -+ * Copyright (C) 2008 Gateworks Corp. -+ * Chris Lang <clang@gateworks.com> -+ * -+ * This program is free software; you can redistribute it and/or modify -+ * it under the terms of the GNU General Public License version 2 as -+ * published by the Free Software Foundation. -+ * -+ */ -+#include <linux/kernel.h> -+#include <linux/init.h> -+#include <linux/platform_device.h> -+#include <linux/leds.h> -+#include <linux/workqueue.h> -+#include <asm/io.h> -+#include <linux/spinlock.h> -+#include <linux/slab.h> -+ -+static unsigned int mem_keep = 0xFF; -+static spinlock_t mem_lock; -+static unsigned char *iobase; -+ -+struct latch_led_data { -+ struct led_classdev cdev; -+ struct work_struct work; -+ u8 new_level; -+ u8 bit; -+ void (*set_led)(u8 bit, enum led_brightness value); -+}; -+ -+static void latch_set_led(u8 bit, enum led_brightness value) -+{ -+ if (value == LED_OFF) -+ mem_keep |= (0x1 << bit); -+ else -+ mem_keep &= ~(0x1 << bit); -+ -+ writeb(mem_keep, iobase); -+} -+ -+static void latch_led_set(struct led_classdev *led_cdev, -+ enum led_brightness value) -+{ -+ struct latch_led_data *led_dat = -+ container_of(led_cdev, struct latch_led_data, cdev); -+ -+ raw_spin_lock(mem_lock); -+ -+ led_dat->set_led(led_dat->bit, value); -+ -+ raw_spin_unlock(mem_lock); -+} -+ -+static int latch_led_probe(struct platform_device *pdev) -+{ -+ struct latch_led_platform_data *pdata = pdev->dev.platform_data; -+ struct latch_led *cur_led; -+ struct latch_led_data *leds_data, *led_dat; -+ int i, ret = 0; -+ -+ if (!pdata) -+ return -EBUSY; -+ -+ leds_data = kzalloc(sizeof(struct latch_led_data) * pdata->num_leds, -+ GFP_KERNEL); -+ if (!leds_data) -+ return -ENOMEM; -+ -+ for (i = 0; i < pdata->num_leds; i++) { -+ cur_led = &pdata->leds[i]; -+ led_dat = &leds_data[i]; -+ -+ led_dat->cdev.name = cur_led->name; -+ led_dat->cdev.default_trigger = cur_led->default_trigger; -+ led_dat->cdev.brightness_set = latch_led_set; -+ led_dat->cdev.brightness = LED_OFF; -+ led_dat->bit = cur_led->bit; -+ led_dat->set_led = pdata->set_led ? pdata->set_led : latch_set_led; -+ -+ ret = led_classdev_register(&pdev->dev, &led_dat->cdev); -+ if (ret < 0) { -+ goto err; -+ } -+ } -+ -+ if (!pdata->set_led) { -+ iobase = ioremap_nocache(pdata->mem, 0x1000); -+ writeb(0xFF, iobase); -+ } -+ platform_set_drvdata(pdev, leds_data); -+ -+ return 0; -+ -+err: -+ if (i > 0) { -+ for (i = i - 1; i >= 0; i--) { -+ led_classdev_unregister(&leds_data[i].cdev); -+ } -+ } -+ -+ kfree(leds_data); -+ -+ return ret; -+} -+ -+static int __devexit latch_led_remove(struct platform_device *pdev) -+{ -+ int i; -+ struct latch_led_platform_data *pdata = pdev->dev.platform_data; -+ struct latch_led_data *leds_data; -+ -+ leds_data = platform_get_drvdata(pdev); -+ -+ for (i = 0; i < pdata->num_leds; i++) { -+ led_classdev_unregister(&leds_data[i].cdev); -+ cancel_work_sync(&leds_data[i].work); -+ } -+ -+ kfree(leds_data); -+ -+ return 0; -+} -+ -+static struct platform_driver latch_led_driver = { -+ .probe = latch_led_probe, -+ .remove = __devexit_p(latch_led_remove), -+ .driver = { -+ .name = "leds-latch", -+ .owner = THIS_MODULE, -+ }, -+}; -+ -+static int __init latch_led_init(void) -+{ -+ return platform_driver_register(&latch_led_driver); -+} -+ -+static void __exit latch_led_exit(void) -+{ -+ platform_driver_unregister(&latch_led_driver); -+} -+ -+module_init(latch_led_init); -+module_exit(latch_led_exit); -+ -+MODULE_AUTHOR("Chris Lang <clang@gateworks.com>"); -+MODULE_DESCRIPTION("Latch LED driver"); -+MODULE_LICENSE("GPL"); ---- a/drivers/leds/Makefile -+++ b/drivers/leds/Makefile -@@ -20,6 +20,7 @@ obj-$(CONFIG_LEDS_COBALT_RAQ) += leds-c - obj-$(CONFIG_LEDS_SUNFIRE) += leds-sunfire.o - obj-$(CONFIG_LEDS_PCA9532) += leds-pca9532.o - obj-$(CONFIG_LEDS_GPIO) += leds-gpio.o -+obj-$(CONFIG_LEDS_LATCH) += leds-latch.o - obj-$(CONFIG_LEDS_LP3944) += leds-lp3944.o - obj-$(CONFIG_LEDS_CLEVO_MAIL) += leds-clevo-mail.o - obj-$(CONFIG_LEDS_HP6XX) += leds-hp6xx.o ---- a/include/linux/leds.h -+++ b/include/linux/leds.h -@@ -161,5 +161,19 @@ struct gpio_led_platform_data { - unsigned long *delay_off); - }; - -+/* For the leds-latch driver */ -+struct latch_led { -+ const char *name; -+ char *default_trigger; -+ unsigned bit; -+}; -+ -+struct latch_led_platform_data { -+ int num_leds; -+ u32 mem; -+ struct latch_led *leds; -+ void (*set_led)(u8 bit, enum led_brightness value); -+}; -+ - - #endif /* __LINUX_LEDS_H_INCLUDED */ diff --git a/target/linux/ixp4xx/patches-2.6.33/300-avila_fetch_mac.patch b/target/linux/ixp4xx/patches-2.6.33/300-avila_fetch_mac.patch deleted file mode 100644 index 329fd9573..000000000 --- a/target/linux/ixp4xx/patches-2.6.33/300-avila_fetch_mac.patch +++ /dev/null @@ -1,244 +0,0 @@ ---- a/arch/arm/mach-ixp4xx/avila-setup.c -+++ b/arch/arm/mach-ixp4xx/avila-setup.c -@@ -14,10 +14,16 @@ - #include <linux/kernel.h> - #include <linux/init.h> - #include <linux/device.h> -+#include <linux/if_ether.h> -+#include <linux/socket.h> -+#include <linux/netdevice.h> - #include <linux/serial.h> - #include <linux/tty.h> - #include <linux/serial_8250.h> - #include <linux/slab.h> -+#include <linux/i2c.h> -+#include <linux/i2c/at24.h> -+ - #include <linux/i2c-gpio.h> - #include <asm/types.h> - #include <asm/setup.h> -@@ -31,6 +37,13 @@ - #define AVILA_SDA_PIN 7 - #define AVILA_SCL_PIN 6 - -+struct avila_board_info { -+ unsigned char *model; -+ void (*setup)(void); -+}; -+ -+static struct avila_board_info *avila_info __initdata; -+ - static struct flash_platform_data avila_flash_data = { - .map_name = "cfi_probe", - .width = 2, -@@ -134,16 +147,181 @@ static struct platform_device avila_pata - .resource = avila_pata_resources, - }; - -+/* Built-in 10/100 Ethernet MAC interfaces */ -+static struct eth_plat_info avila_npeb_data = { -+ .phy = 0, -+ .rxq = 3, -+ .txreadyq = 20, -+}; -+ -+static struct eth_plat_info avila_npec_data = { -+ .phy = 1, -+ .rxq = 4, -+ .txreadyq = 21, -+}; -+ -+static struct platform_device avila_npeb_device = { -+ .name = "ixp4xx_eth", -+ .id = IXP4XX_ETH_NPEB, -+ .dev.platform_data = &avila_npeb_data, -+}; -+ -+static struct platform_device avila_npec_device = { -+ .name = "ixp4xx_eth", -+ .id = IXP4XX_ETH_NPEC, -+ .dev.platform_data = &avila_npec_data, -+}; -+ - static struct platform_device *avila_devices[] __initdata = { - &avila_i2c_gpio, - &avila_flash, - &avila_uart - }; - -+static void __init avila_gw23xx_setup(void) -+{ -+ platform_device_register(&avila_npeb_device); -+ platform_device_register(&avila_npec_device); -+} -+ -+static void __init avila_gw2342_setup(void) -+{ -+ platform_device_register(&avila_npeb_device); -+ platform_device_register(&avila_npec_device); -+} -+ -+static void __init avila_gw2345_setup(void) -+{ -+ avila_npeb_data.phy = IXP4XX_ETH_PHY_MAX_ADDR; -+ avila_npeb_data.phy_mask = 0x1e; /* ports 1-4 of the KS8995 switch */ -+ platform_device_register(&avila_npeb_device); -+ -+ avila_npec_data.phy = 5; /* port 5 of the KS8995 switch */ -+ platform_device_register(&avila_npec_device); -+} -+ -+static void __init avila_gw2347_setup(void) -+{ -+ platform_device_register(&avila_npeb_device); -+} -+ -+static void __init avila_gw2348_setup(void) -+{ -+ platform_device_register(&avila_npeb_device); -+ platform_device_register(&avila_npec_device); -+} -+ -+static void __init avila_gw2353_setup(void) -+{ -+ platform_device_register(&avila_npeb_device); -+} -+ -+static void __init avila_gw2355_setup(void) -+{ -+ avila_npeb_data.phy = IXP4XX_ETH_PHY_MAX_ADDR; -+ avila_npeb_data.phy_mask = 0x1e; /* ports 1-4 of the KS8995 switch */ -+ platform_device_register(&avila_npeb_device); -+ -+ avila_npec_data.phy = 16; -+ platform_device_register(&avila_npec_device); -+} -+ -+static void __init avila_gw2357_setup(void) -+{ -+ platform_device_register(&avila_npeb_device); -+} -+ -+static struct avila_board_info avila_boards[] __initdata = { -+ { -+ .model = "GW2342", -+ .setup = avila_gw2342_setup, -+ }, { -+ .model = "GW2345", -+ .setup = avila_gw2345_setup, -+ }, { -+ .model = "GW2347", -+ .setup = avila_gw2347_setup, -+ }, { -+ .model = "GW2348", -+ .setup = avila_gw2348_setup, -+ }, { -+ .model = "GW2353", -+ .setup = avila_gw2353_setup, -+ }, { -+ .model = "GW2355", -+ .setup = avila_gw2355_setup, -+ }, { -+ .model = "GW2357", -+ .setup = avila_gw2357_setup, -+ } -+}; -+ -+static struct avila_board_info * __init avila_find_board_info(char *model) -+{ -+ int i; -+ model[6] = '\0'; -+ -+ for (i = 0; i < ARRAY_SIZE(avila_boards); i++) { -+ struct avila_board_info *info = &avila_boards[i]; -+ if (strcmp(info->model, model) == 0) -+ return info; -+ } -+ -+ return NULL; -+} -+ -+static struct memory_accessor *at24_mem_acc; -+ -+static void at24_setup(struct memory_accessor *mem_acc, void *context) -+{ -+ char mac_addr[ETH_ALEN]; -+ char model[7]; -+ -+ at24_mem_acc = mem_acc; -+ -+ /* Read MAC addresses */ -+ if (at24_mem_acc->read(at24_mem_acc, mac_addr, 0x0, 6) == 6) { -+ memcpy(&avila_npeb_data.hwaddr, mac_addr, ETH_ALEN); -+ } -+ if (at24_mem_acc->read(at24_mem_acc, mac_addr, 0x6, 6) == 6) { -+ memcpy(&avila_npec_data.hwaddr, mac_addr, ETH_ALEN); -+ } -+ -+ /* Read the first 6 bytes of the model number */ -+ if (at24_mem_acc->read(at24_mem_acc, model, 0x20, 6) == 6) { -+ avila_info = avila_find_board_info(model); -+ } -+ -+} -+ -+static struct at24_platform_data avila_eeprom_info = { -+ .byte_len = 1024, -+ .page_size = 16, -+ .flags = AT24_FLAG_READONLY, -+ .setup = at24_setup, -+}; -+ -+static struct i2c_board_info __initdata avila_i2c_board_info[] = { -+ { -+ I2C_BOARD_INFO("ds1672", 0x68), -+ }, -+ { -+ I2C_BOARD_INFO("ad7418", 0x28), -+ }, -+ { -+ I2C_BOARD_INFO("24c08", 0x51), -+ .platform_data = &avila_eeprom_info -+ }, -+}; -+ - static void __init avila_init(void) - { - ixp4xx_sys_init(); - -+ /* -+ * These devices are present on all Avila models and don't need any -+ * model specific setup. -+ */ - avila_flash_resource.start = IXP4XX_EXP_BUS_BASE(0); - avila_flash_resource.end = - IXP4XX_EXP_BUS_BASE(0) + ixp4xx_exp_bus_size - 1; -@@ -161,7 +339,28 @@ static void __init avila_init(void) - - platform_device_register(&avila_pata); - -+ i2c_register_board_info(0, avila_i2c_board_info, -+ ARRAY_SIZE(avila_i2c_board_info)); -+} -+ -+static int __init avila_model_setup(void) -+{ -+ if (!machine_is_avila()) -+ return 0; -+ -+ if (avila_info) { -+ printk(KERN_DEBUG "Running on Gateworks Avila %s\n", -+ avila_info->model); -+ avila_info->setup(); -+ } else { -+ printk(KERN_INFO "Unknown/missing Avila model number" -+ " -- defaults will be used\n"); -+ avila_gw23xx_setup(); -+ } -+ -+ return 0; - } -+late_initcall(avila_model_setup); - - MACHINE_START(AVILA, "Gateworks Avila Network Platform") - /* Maintainer: Deepak Saxena <dsaxena@plexity.net> */ diff --git a/target/linux/ixp4xx/patches-2.6.33/301-avila_led.patch b/target/linux/ixp4xx/patches-2.6.33/301-avila_led.patch deleted file mode 100644 index cc5fadeed..000000000 --- a/target/linux/ixp4xx/patches-2.6.33/301-avila_led.patch +++ /dev/null @@ -1,161 +0,0 @@ ---- a/arch/arm/mach-ixp4xx/avila-setup.c -+++ b/arch/arm/mach-ixp4xx/avila-setup.c -@@ -24,6 +24,7 @@ - #include <linux/i2c.h> - #include <linux/i2c/at24.h> - -+#include <linux/leds.h> - #include <linux/i2c-gpio.h> - #include <asm/types.h> - #include <asm/setup.h> -@@ -172,6 +173,72 @@ static struct platform_device avila_npec - .dev.platform_data = &avila_npec_data, - }; - -+static struct gpio_led avila_gpio_leds[] = { -+ { -+ .name = "user", /* green led */ -+ .gpio = AVILA_GW23XX_LED_USER_GPIO, -+ .active_low = 1, -+ } -+}; -+ -+static struct gpio_led_platform_data avila_gpio_leds_data = { -+ .num_leds = 1, -+ .leds = avila_gpio_leds, -+}; -+ -+static struct platform_device avila_gpio_leds_device = { -+ .name = "leds-gpio", -+ .id = -1, -+ .dev.platform_data = &avila_gpio_leds_data, -+}; -+ -+static struct latch_led avila_latch_leds[] = { -+ { -+ .name = "led0", /* green led */ -+ .bit = 0, -+ }, -+ { -+ .name = "led1", /* green led */ -+ .bit = 1, -+ }, -+ { -+ .name = "led2", /* green led */ -+ .bit = 2, -+ }, -+ { -+ .name = "led3", /* green led */ -+ .bit = 3, -+ }, -+ { -+ .name = "led4", /* green led */ -+ .bit = 4, -+ }, -+ { -+ .name = "led5", /* green led */ -+ .bit = 5, -+ }, -+ { -+ .name = "led6", /* green led */ -+ .bit = 6, -+ }, -+ { -+ .name = "led7", /* green led */ -+ .bit = 7, -+ } -+}; -+ -+static struct latch_led_platform_data avila_latch_leds_data = { -+ .num_leds = 8, -+ .leds = avila_latch_leds, -+ .mem = 0x51000000, -+}; -+ -+static struct platform_device avila_latch_leds_device = { -+ .name = "leds-latch", -+ .id = -1, -+ .dev.platform_data = &avila_latch_leds_data, -+}; -+ - static struct platform_device *avila_devices[] __initdata = { - &avila_i2c_gpio, - &avila_flash, -@@ -182,12 +249,16 @@ static void __init avila_gw23xx_setup(vo - { - platform_device_register(&avila_npeb_device); - platform_device_register(&avila_npec_device); -+ -+ platform_device_register(&avila_gpio_leds_device); - } - - static void __init avila_gw2342_setup(void) - { - platform_device_register(&avila_npeb_device); - platform_device_register(&avila_npec_device); -+ -+ platform_device_register(&avila_gpio_leds_device); - } - - static void __init avila_gw2345_setup(void) -@@ -198,22 +269,30 @@ static void __init avila_gw2345_setup(vo - - avila_npec_data.phy = 5; /* port 5 of the KS8995 switch */ - platform_device_register(&avila_npec_device); -+ -+ platform_device_register(&avila_gpio_leds_device); - } - - static void __init avila_gw2347_setup(void) - { - platform_device_register(&avila_npeb_device); -+ -+ avila_gpio_leds[0].gpio = AVILA_GW23X7_LED_USER_GPIO; -+ platform_device_register(&avila_gpio_leds_device); - } - - static void __init avila_gw2348_setup(void) - { - platform_device_register(&avila_npeb_device); - platform_device_register(&avila_npec_device); -+ -+ platform_device_register(&avila_gpio_leds_device); - } - - static void __init avila_gw2353_setup(void) - { - platform_device_register(&avila_npeb_device); -+ platform_device_register(&avila_gpio_leds_device); - } - - static void __init avila_gw2355_setup(void) -@@ -224,11 +303,29 @@ static void __init avila_gw2355_setup(vo - - avila_npec_data.phy = 16; - platform_device_register(&avila_npec_device); -+ -+ platform_device_register(&avila_gpio_leds_device); -+ -+ *IXP4XX_EXP_CS4 |= 0xbfff3c03; -+ avila_latch_leds[0].name = "RXD"; -+ avila_latch_leds[1].name = "TXD"; -+ avila_latch_leds[2].name = "POL"; -+ avila_latch_leds[3].name = "LNK"; -+ avila_latch_leds[4].name = "ERR"; -+ avila_latch_leds_data.num_leds = 5; -+ avila_latch_leds_data.mem = 0x54000000; -+ platform_device_register(&avila_latch_leds_device); - } - - static void __init avila_gw2357_setup(void) - { - platform_device_register(&avila_npeb_device); -+ -+ avila_gpio_leds[0].gpio = AVILA_GW23X7_LED_USER_GPIO; -+ platform_device_register(&avila_gpio_leds_device); -+ -+ *IXP4XX_EXP_CS1 |= 0xbfff3c03; -+ platform_device_register(&avila_latch_leds_device); - } - - static struct avila_board_info avila_boards[] __initdata = { diff --git a/target/linux/ixp4xx/patches-2.6.33/302-avila_gpio_device.patch b/target/linux/ixp4xx/patches-2.6.33/302-avila_gpio_device.patch deleted file mode 100644 index f941a94bc..000000000 --- a/target/linux/ixp4xx/patches-2.6.33/302-avila_gpio_device.patch +++ /dev/null @@ -1,16 +0,0 @@ ---- a/arch/arm/mach-ixp4xx/avila-setup.c -+++ b/arch/arm/mach-ixp4xx/avila-setup.c -@@ -38,6 +38,13 @@ - #define AVILA_SDA_PIN 7 - #define AVILA_SCL_PIN 6 - -+/* User LEDs */ -+#define AVILA_GW23XX_LED_USER_GPIO 3 -+#define AVILA_GW23X7_LED_USER_GPIO 4 -+ -+/* gpio mask used by platform device */ -+#define AVILA_GPIO_MASK (1 << 1) | (1 << 3) | (1 << 5) | (1 << 7) | (1 << 9) -+ - struct avila_board_info { - unsigned char *model; - void (*setup)(void); diff --git a/target/linux/ixp4xx/patches-2.6.33/304-ixp4xx_eth_jumboframe.patch b/target/linux/ixp4xx/patches-2.6.33/304-ixp4xx_eth_jumboframe.patch deleted file mode 100644 index a9cbddcf5..000000000 --- a/target/linux/ixp4xx/patches-2.6.33/304-ixp4xx_eth_jumboframe.patch +++ /dev/null @@ -1,80 +0,0 @@ ---- a/drivers/net/arm/ixp4xx_eth.c -+++ b/drivers/net/arm/ixp4xx_eth.c -@@ -52,7 +52,7 @@ - - #define POOL_ALLOC_SIZE (sizeof(struct desc) * (RX_DESCS + TX_DESCS)) - #define REGS_SIZE 0x1000 --#define MAX_MRU 1536 /* 0x600 */ -+#define MAX_MRU (14320 - ETH_HLEN - ETH_FCS_LEN) - #define RX_BUFF_SIZE ALIGN((NET_IP_ALIGN) + MAX_MRU, 4) - - #define NAPI_WEIGHT 16 -@@ -1061,6 +1061,32 @@ static void destroy_queues(struct port * - } - } - -+static int eth_do_change_mtu(struct net_device *dev, int mtu) -+{ -+ struct port *port; -+ struct msg msg; -+ /* adjust for ethernet headers */ -+ int framesize = mtu + ETH_HLEN + ETH_FCS_LEN; -+ -+ port = netdev_priv(dev); -+ -+ memset(&msg, 0, sizeof(msg)); -+ msg.cmd = NPE_SETMAXFRAMELENGTHS; -+ msg.eth_id = port->id; -+ -+ /* max rx/tx 64 byte blocks */ -+ msg.byte2 = ((framesize + 63) / 64) << 8; -+ msg.byte3 = ((framesize + 63) / 64) << 8; -+ -+ msg.byte4 = msg.byte6 = framesize >> 8; -+ msg.byte5 = msg.byte7 = framesize & 0xff; -+ -+ if (npe_send_recv_message(port->npe, &msg, "ETH_SET_MAX_FRAME_LENGTH")) -+ return -EIO; -+ -+ return 0; -+} -+ - static int eth_open(struct net_device *dev) - { - struct port *port = netdev_priv(dev); -@@ -1112,6 +1138,8 @@ static int eth_open(struct net_device *d - if (npe_send_recv_message(port->npe, &msg, "ETH_SET_FIREWALL_MODE")) - return -EIO; - -+ eth_do_change_mtu(dev, dev->mtu); -+ - if ((err = request_queues(port)) != 0) - return err; - -@@ -1251,7 +1279,26 @@ static int eth_close(struct net_device * - return 0; - } - -+static int ixp_eth_change_mtu(struct net_device *dev, int mtu) -+{ -+ int ret; -+ -+ if (mtu > MAX_MRU) -+ return -EINVAL; -+ -+ if (dev->flags & IFF_UP) { -+ ret = eth_do_change_mtu(dev, mtu); -+ if (ret < 0) -+ return ret; -+ } -+ -+ dev->mtu = mtu; -+ -+ return 0; -+} -+ - static const struct net_device_ops ixp4xx_netdev_ops = { -+ .ndo_change_mtu = ixp_eth_change_mtu, - .ndo_open = eth_open, - .ndo_stop = eth_close, - .ndo_start_xmit = eth_xmit, diff --git a/target/linux/ixp4xx/patches-2.6.33/310-gtwx5717_spi_bus.patch b/target/linux/ixp4xx/patches-2.6.33/310-gtwx5717_spi_bus.patch deleted file mode 100644 index 164e03e77..000000000 --- a/target/linux/ixp4xx/patches-2.6.33/310-gtwx5717_spi_bus.patch +++ /dev/null @@ -1,52 +0,0 @@ ---- a/arch/arm/mach-ixp4xx/gtwx5715-setup.c -+++ b/arch/arm/mach-ixp4xx/gtwx5715-setup.c -@@ -28,6 +28,7 @@ - #include <linux/tty.h> - #include <linux/serial_8250.h> - #include <linux/slab.h> -+#include <linux/spi/spi_gpio_old.h> - #include <asm/types.h> - #include <asm/setup.h> - #include <asm/memory.h> -@@ -147,9 +148,41 @@ static struct platform_device gtwx5715_f - .resource = >wx5715_flash_resource, - }; - -+static int gtwx5715_spi_boardinfo_setup(struct spi_board_info *bi, -+ struct spi_master *master, void *data) -+{ -+ -+ strlcpy(bi->modalias, "spi-ks8995", sizeof(bi->modalias)); -+ -+ bi->max_speed_hz = 5000000 /* Hz */; -+ bi->bus_num = master->bus_num; -+ bi->mode = SPI_MODE_0; -+ -+ return 0; -+} -+ -+static struct spi_gpio_platform_data gtwx5715_spi_bus_data = { -+ .pin_cs = GTWX5715_KSSPI_SELECT, -+ .pin_clk = GTWX5715_KSSPI_CLOCK, -+ .pin_miso = GTWX5715_KSSPI_RXD, -+ .pin_mosi = GTWX5715_KSSPI_TXD, -+ .cs_activelow = 1, -+ .no_spi_delay = 1, -+ .boardinfo_setup = gtwx5715_spi_boardinfo_setup, -+}; -+ -+static struct platform_device gtwx5715_spi_bus = { -+ .name = "spi-gpio", -+ .id = 0, -+ .dev = { -+ .platform_data = >wx5715_spi_bus_data, -+ }, -+}; -+ - static struct platform_device *gtwx5715_devices[] __initdata = { - >wx5715_uart_device, - >wx5715_flash, -+ >wx5715_spi_bus, - }; - - static void __init gtwx5715_init(void) diff --git a/target/linux/ixp4xx/patches-2.6.33/311-gtwx5717_mac_plat_info.patch b/target/linux/ixp4xx/patches-2.6.33/311-gtwx5717_mac_plat_info.patch deleted file mode 100644 index 8ce79e4d0..000000000 --- a/target/linux/ixp4xx/patches-2.6.33/311-gtwx5717_mac_plat_info.patch +++ /dev/null @@ -1,40 +0,0 @@ ---- a/arch/arm/mach-ixp4xx/gtwx5715-setup.c -+++ b/arch/arm/mach-ixp4xx/gtwx5715-setup.c -@@ -179,10 +179,37 @@ static struct platform_device gtwx5715_s - }, - }; - -+static struct eth_plat_info gtwx5715_npeb_data = { -+ .phy = IXP4XX_ETH_PHY_MAX_ADDR, -+ .phy_mask = 0x1e, /* ports 1-4 of the KS8995 switch */ -+ .rxq = 3, -+ .txreadyq = 20, -+}; -+ -+static struct eth_plat_info gtwx5715_npec_data = { -+ .phy = 5, /* port 5 of the KS8995 switch */ -+ .rxq = 4, -+ .txreadyq = 21, -+}; -+ -+static struct platform_device gtwx5715_npeb_device = { -+ .name = "ixp4xx_eth", -+ .id = IXP4XX_ETH_NPEB, -+ .dev.platform_data = >wx5715_npeb_data, -+}; -+ -+static struct platform_device gtwx5715_npec_device = { -+ .name = "ixp4xx_eth", -+ .id = IXP4XX_ETH_NPEC, -+ .dev.platform_data = >wx5715_npec_data, -+}; -+ - static struct platform_device *gtwx5715_devices[] __initdata = { - >wx5715_uart_device, - >wx5715_flash, - >wx5715_spi_bus, -+ >wx5715_npeb_device, -+ >wx5715_npec_device, - }; - - static void __init gtwx5715_init(void) diff --git a/target/linux/ixp4xx/patches-2.6.33/312-ixp4xx_pata_optimization.patch b/target/linux/ixp4xx/patches-2.6.33/312-ixp4xx_pata_optimization.patch deleted file mode 100644 index 3bf1b7497..000000000 --- a/target/linux/ixp4xx/patches-2.6.33/312-ixp4xx_pata_optimization.patch +++ /dev/null @@ -1,137 +0,0 @@ ---- a/drivers/ata/pata_ixp4xx_cf.c -+++ b/drivers/ata/pata_ixp4xx_cf.c -@@ -24,16 +24,58 @@ - #include <scsi/scsi_host.h> - - #define DRV_NAME "pata_ixp4xx_cf" --#define DRV_VERSION "0.2" -+#define DRV_VERSION "0.3" - - static int ixp4xx_set_mode(struct ata_link *link, struct ata_device **error) - { - struct ata_device *dev; -+ struct ixp4xx_pata_data *data = link->ap->host->dev->platform_data; -+ unsigned int pio_mask; - - ata_for_each_dev(dev, link, ENABLED) { -- ata_dev_printk(dev, KERN_INFO, "configured for PIO0\n"); -- dev->pio_mode = XFER_PIO_0; -- dev->xfer_mode = XFER_PIO_0; -+ if (dev->id[ATA_ID_FIELD_VALID] & (1 << 1)) { -+ pio_mask = dev->id[ATA_ID_PIO_MODES] & 0x03; -+ if (pio_mask & (1 << 1)) { -+ pio_mask = 4; -+ } else { -+ pio_mask = 3; -+ } -+ } else { -+ pio_mask = (dev->id[ATA_ID_OLD_PIO_MODES] >> 8); -+ } -+ -+ switch (pio_mask){ -+ case 0: -+ ata_dev_printk(dev, KERN_INFO, "configured for PIO0\n"); -+ dev->pio_mode = XFER_PIO_0; -+ dev->xfer_mode = XFER_PIO_0; -+ *data->cs0_cfg = 0x8a473c03; -+ break; -+ case 1: -+ ata_dev_printk(dev, KERN_INFO, "configured for PIO1\n"); -+ dev->pio_mode = XFER_PIO_1; -+ dev->xfer_mode = XFER_PIO_1; -+ *data->cs0_cfg = 0x86433c03; -+ break; -+ case 2: -+ ata_dev_printk(dev, KERN_INFO, "configured for PIO2\n"); -+ dev->pio_mode = XFER_PIO_2; -+ dev->xfer_mode = XFER_PIO_2; -+ *data->cs0_cfg = 0x82413c03; -+ break; -+ case 3: -+ ata_dev_printk(dev, KERN_INFO, "configured for PIO3\n"); -+ dev->pio_mode = XFER_PIO_3; -+ dev->xfer_mode = XFER_PIO_3; -+ *data->cs0_cfg = 0x80823c03; -+ break; -+ case 4: -+ ata_dev_printk(dev, KERN_INFO, "configured for PIO4\n"); -+ dev->pio_mode = XFER_PIO_4; -+ dev->xfer_mode = XFER_PIO_4; -+ *data->cs0_cfg = 0x80403c03; -+ break; -+ } - dev->xfer_shift = ATA_SHIFT_PIO; - dev->flags |= ATA_DFLAG_PIO; - } -@@ -46,6 +88,7 @@ static unsigned int ixp4xx_mmio_data_xfe - unsigned int i; - unsigned int words = buflen >> 1; - u16 *buf16 = (u16 *) buf; -+ unsigned int pio_mask; - struct ata_port *ap = dev->link->ap; - void __iomem *mmio = ap->ioaddr.data_addr; - struct ixp4xx_pata_data *data = ap->host->dev->platform_data; -@@ -53,8 +96,34 @@ static unsigned int ixp4xx_mmio_data_xfe - /* set the expansion bus in 16bit mode and restore - * 8 bit mode after the transaction. - */ -- *data->cs0_cfg &= ~(0x01); -- udelay(100); -+ if (dev->id[ATA_ID_FIELD_VALID] & (1 << 1)){ -+ pio_mask = dev->id[ATA_ID_PIO_MODES] & 0x03; -+ if (pio_mask & (1 << 1)){ -+ pio_mask = 4; -+ }else{ -+ pio_mask = 3; -+ } -+ }else{ -+ pio_mask = (dev->id[ATA_ID_OLD_PIO_MODES] >> 8); -+ } -+ switch (pio_mask){ -+ case 0: -+ *data->cs0_cfg = 0xa9643c42; -+ break; -+ case 1: -+ *data->cs0_cfg = 0x85033c42; -+ break; -+ case 2: -+ *data->cs0_cfg = 0x80b23c42; -+ break; -+ case 3: -+ *data->cs0_cfg = 0x80823c42; -+ break; -+ case 4: -+ *data->cs0_cfg = 0x80403c42; -+ break; -+ } -+ udelay(5); - - /* Transfer multiple of 2 bytes */ - if (rw == READ) -@@ -79,8 +148,24 @@ static unsigned int ixp4xx_mmio_data_xfe - words++; - } - -- udelay(100); -- *data->cs0_cfg |= 0x01; -+ udelay(5); -+ switch (pio_mask){ -+ case 0: -+ *data->cs0_cfg = 0x8a473c03; -+ break; -+ case 1: -+ *data->cs0_cfg = 0x86433c03; -+ break; -+ case 2: -+ *data->cs0_cfg = 0x82413c03; -+ break; -+ case 3: -+ *data->cs0_cfg = 0x80823c03; -+ break; -+ case 4: -+ *data->cs0_cfg = 0x80403c03; -+ break; -+ } - - return words << 1; - } diff --git a/target/linux/ixp4xx/patches-2.6.33/401-avila_pci_dev.patch b/target/linux/ixp4xx/patches-2.6.33/401-avila_pci_dev.patch deleted file mode 100644 index 80f4de7a3..000000000 --- a/target/linux/ixp4xx/patches-2.6.33/401-avila_pci_dev.patch +++ /dev/null @@ -1,11 +0,0 @@ ---- a/arch/arm/mach-ixp4xx/avila-pci.c -+++ b/arch/arm/mach-ixp4xx/avila-pci.c -@@ -27,7 +27,7 @@ - #include <mach/hardware.h> - #include <asm/mach-types.h> - --#define AVILA_MAX_DEV 4 -+#define AVILA_MAX_DEV 6 - #define LOFT_MAX_DEV 6 - #define IRQ_LINES 4 - diff --git a/target/linux/ixp4xx/patches-2.6.33/402-ixp4xx_gpiolib.patch b/target/linux/ixp4xx/patches-2.6.33/402-ixp4xx_gpiolib.patch deleted file mode 100644 index 1b1b91065..000000000 --- a/target/linux/ixp4xx/patches-2.6.33/402-ixp4xx_gpiolib.patch +++ /dev/null @@ -1,136 +0,0 @@ ---- a/arch/arm/mach-ixp4xx/common.c -+++ b/arch/arm/mach-ixp4xx/common.c -@@ -36,6 +36,7 @@ - #include <asm/pgtable.h> - #include <asm/page.h> - #include <asm/irq.h> -+#include <asm/gpio.h> - - #include <asm/mach/map.h> - #include <asm/mach/irq.h> -@@ -375,12 +376,50 @@ static struct platform_device *ixp46x_de - unsigned long ixp4xx_exp_bus_size; - EXPORT_SYMBOL(ixp4xx_exp_bus_size); - -+static int ixp4xx_gpio_direction_input(struct gpio_chip *chip, unsigned gpio) -+{ -+ gpio_line_config(gpio, IXP4XX_GPIO_IN); -+ return 0; -+} -+ -+static int ixp4xx_gpio_direction_output(struct gpio_chip *chip, unsigned gpio, int level) -+{ -+ gpio_line_set(gpio, level); -+ gpio_line_config(gpio, IXP4XX_GPIO_OUT); -+ return 0; -+} -+ -+static int ixp4xx_gpio_get_value(struct gpio_chip *chip, unsigned gpio) -+{ -+ int value; -+ -+ gpio_line_get(gpio, &value); -+ return value; -+} -+ -+static void ixp4xx_gpio_set_value(struct gpio_chip *chip, unsigned gpio, int value) -+{ -+ gpio_line_set(gpio, value); -+} -+ -+static struct gpio_chip ixp4xx_gpio_chip = { -+ .label = "IXP4XX_GPIO_CHIP", -+ .direction_input = ixp4xx_gpio_direction_input, -+ .direction_output = ixp4xx_gpio_direction_output, -+ .get = ixp4xx_gpio_get_value, -+ .set = ixp4xx_gpio_set_value, -+ .base = 0, -+ .ngpio = 16, -+}; -+ - void __init ixp4xx_sys_init(void) - { - ixp4xx_exp_bus_size = SZ_16M; - - platform_add_devices(ixp4xx_devices, ARRAY_SIZE(ixp4xx_devices)); - -+ gpiochip_add(&ixp4xx_gpio_chip); -+ - if (cpu_is_ixp46x()) { - int region; - ---- a/arch/arm/Kconfig -+++ b/arch/arm/Kconfig -@@ -418,6 +418,7 @@ config ARCH_IXP4XX - select GENERIC_GPIO - select GENERIC_TIME - select GENERIC_CLOCKEVENTS -+ select ARCH_REQUIRE_GPIOLIB - help - Support for Intel's IXP4XX (XScale) family of processors. - ---- a/arch/arm/mach-ixp4xx/include/mach/gpio.h -+++ b/arch/arm/mach-ixp4xx/include/mach/gpio.h -@@ -27,47 +27,31 @@ - - #include <linux/kernel.h> - #include <mach/hardware.h> -+#include <asm-generic/gpio.h> /* cansleep wrappers */ - --static inline int gpio_request(unsigned gpio, const char *label) --{ -- return 0; --} -- --static inline void gpio_free(unsigned gpio) --{ -- might_sleep(); -- -- return; --} -- --static inline int gpio_direction_input(unsigned gpio) --{ -- gpio_line_config(gpio, IXP4XX_GPIO_IN); -- return 0; --} -- --static inline int gpio_direction_output(unsigned gpio, int level) --{ -- gpio_line_set(gpio, level); -- gpio_line_config(gpio, IXP4XX_GPIO_OUT); -- return 0; --} -+#define NR_BUILTIN_GPIO 16 - - static inline int gpio_get_value(unsigned gpio) - { -- int value; -- -- gpio_line_get(gpio, &value); -- -- return value; -+ if (gpio < NR_BUILTIN_GPIO) -+ { -+ int value; -+ gpio_line_get(gpio, &value); -+ return value; -+ } -+ else -+ return __gpio_get_value(gpio); - } - - static inline void gpio_set_value(unsigned gpio, int value) - { -- gpio_line_set(gpio, value); -+ if (gpio < NR_BUILTIN_GPIO) -+ gpio_line_set(gpio, value); -+ else -+ __gpio_set_value(gpio, value); - } - --#include <asm-generic/gpio.h> /* cansleep wrappers */ -+#define gpio_cansleep __gpio_cansleep - - extern int gpio_to_irq(int gpio); - extern int irq_to_gpio(unsigned int irq); diff --git a/target/linux/ixp4xx/patches-2.6.33/500-usr8200_support.patch b/target/linux/ixp4xx/patches-2.6.33/500-usr8200_support.patch deleted file mode 100644 index 2d78425f4..000000000 --- a/target/linux/ixp4xx/patches-2.6.33/500-usr8200_support.patch +++ /dev/null @@ -1,342 +0,0 @@ ---- a/arch/arm/mach-ixp4xx/Kconfig -+++ b/arch/arm/mach-ixp4xx/Kconfig -@@ -97,6 +97,14 @@ config MACH_SIDEWINDER - Engineering Sidewinder board. For more information on this - platform, see http://www.adiengineering.com - -+config MACH_USR8200 -+ bool "USRobotics USR8200" -+ select PCI -+ help -+ Say 'Y' here if you want your kernel to support the USRobotics -+ USR8200 router board. For more information on this platform, see -+ http://openwrt.org -+ - config MACH_COMPEX - bool "Compex WP18 / NP18A" - select PCI ---- a/arch/arm/mach-ixp4xx/Makefile -+++ b/arch/arm/mach-ixp4xx/Makefile -@@ -25,6 +25,7 @@ obj-pci-$(CONFIG_MACH_WRT300NV2) += wrt - obj-pci-$(CONFIG_MACH_AP1000) += ixdp425-pci.o - obj-pci-$(CONFIG_MACH_TW5334) += tw5334-pci.o - obj-pci-$(CONFIG_MACH_MI424WR) += mi424wr-pci.o -+obj-pci-$(CONFIG_MACH_USR8200) += usr8200-pci.o - - obj-y += common.o - -@@ -49,6 +50,7 @@ obj-$(CONFIG_MACH_WRT300NV2) += wrt300nv - obj-$(CONFIG_MACH_AP1000) += ap1000-setup.o - obj-$(CONFIG_MACH_TW5334) += tw5334-setup.o - obj-$(CONFIG_MACH_MI424WR) += mi424wr-setup.o -+obj-$(CONFIG_MACH_USR8200) += usr8200-setup.o - - obj-$(CONFIG_PCI) += $(obj-pci-$(CONFIG_PCI)) common-pci.o - obj-$(CONFIG_IXP4XX_QMGR) += ixp4xx_qmgr.o ---- /dev/null -+++ b/arch/arm/mach-ixp4xx/usr8200-pci.c -@@ -0,0 +1,78 @@ -+/* -+ * arch/arch/mach-ixp4xx/usr8200-pci.c -+ * -+ * PCI setup routines for USRobotics USR8200 -+ * -+ * Copyright (C) 2008 Peter Denison <openwrt@marshadder.org> -+ * -+ * based on pronghorn-pci.c -+ * Copyright (C) 2008 Imre Kaloz <kaloz@openwrt.org> -+ * based on coyote-pci.c: -+ * Copyright (C) 2002 Jungo Software Technologies. -+ * Copyright (C) 2003 MontaVista Softwrae, Inc. -+ * -+ * Maintainer: Peter Denison <openwrt@marshadder.org> -+ * -+ * This program is free software; you can redistribute it and/or modify -+ * it under the terms of the GNU General Public License version 2 as -+ * published by the Free Software Foundation. -+ * -+ */ -+ -+#include <linux/kernel.h> -+#include <linux/pci.h> -+#include <linux/init.h> -+#include <linux/irq.h> -+ -+#include <asm/mach-types.h> -+#include <mach/hardware.h> -+ -+#include <asm/mach/pci.h> -+ -+void __init usr8200_pci_preinit(void) -+{ -+ set_irq_type(IRQ_IXP4XX_GPIO7, IRQ_TYPE_LEVEL_LOW); -+ set_irq_type(IRQ_IXP4XX_GPIO8, IRQ_TYPE_LEVEL_LOW); -+ set_irq_type(IRQ_IXP4XX_GPIO9, IRQ_TYPE_LEVEL_LOW); -+ set_irq_type(IRQ_IXP4XX_GPIO10, IRQ_TYPE_LEVEL_LOW); -+ set_irq_type(IRQ_IXP4XX_GPIO11, IRQ_TYPE_LEVEL_LOW); -+ -+ ixp4xx_pci_preinit(); -+} -+ -+static int __init usr8200_map_irq(struct pci_dev *dev, u8 slot, u8 pin) -+{ -+ if (slot == 14) -+ return IRQ_IXP4XX_GPIO7; -+ else if (slot == 15) -+ return IRQ_IXP4XX_GPIO8; -+ else if (slot == 16) { -+ if (pin == 1) -+ return IRQ_IXP4XX_GPIO11; -+ else if (pin == 2) -+ return IRQ_IXP4XX_GPIO10; -+ else if (pin == 3) -+ return IRQ_IXP4XX_GPIO9; -+ else -+ return -1; -+ } else -+ return -1; -+} -+ -+struct hw_pci usr8200_pci __initdata = { -+ .nr_controllers = 1, -+ .preinit = usr8200_pci_preinit, -+ .swizzle = pci_std_swizzle, -+ .setup = ixp4xx_setup, -+ .scan = ixp4xx_scan_bus, -+ .map_irq = usr8200_map_irq, -+}; -+ -+int __init usr8200_pci_init(void) -+{ -+ if (machine_is_usr8200()) -+ pci_common_init(&usr8200_pci); -+ return 0; -+} -+ -+subsys_initcall(usr8200_pci_init); ---- /dev/null -+++ b/arch/arm/mach-ixp4xx/usr8200-setup.c -@@ -0,0 +1,212 @@ -+/* -+ * arch/arm/mach-ixp4xx/usr8200-setup.c -+ * -+ * Board setup for the USRobotics USR8200 -+ * -+ * Copyright (C) 2008 Peter Denison <openwrt@marshadder.org> -+ * -+ * based on pronghorn-setup.c: -+ * Copyright (C) 2008 Imre Kaloz <kaloz@openwrt.org> -+ * based on coyote-setup.c: -+ * Copyright (C) 2003-2005 MontaVista Software, Inc. -+ * -+ * Author: Peter Denison <openwrt@marshadder.org> -+ */ -+ -+#include <linux/kernel.h> -+#include <linux/init.h> -+#include <linux/device.h> -+#include <linux/serial.h> -+#include <linux/tty.h> -+#include <linux/serial_8250.h> -+#include <linux/slab.h> -+#include <linux/types.h> -+#include <linux/memory.h> -+#include <linux/i2c-gpio.h> -+#include <linux/leds.h> -+ -+#include <asm/setup.h> -+#include <mach/hardware.h> -+#include <asm/irq.h> -+#include <asm/mach-types.h> -+#include <asm/mach/arch.h> -+#include <asm/mach/flash.h> -+ -+static struct flash_platform_data usr8200_flash_data = { -+ .map_name = "cfi_probe", -+ .width = 2, -+}; -+ -+static struct resource usr8200_flash_resource = { -+ .flags = IORESOURCE_MEM, -+}; -+ -+static struct platform_device usr8200_flash = { -+ .name = "IXP4XX-Flash", -+ .id = 0, -+ .dev = { -+ .platform_data = &usr8200_flash_data, -+ }, -+ .num_resources = 1, -+ .resource = &usr8200_flash_resource, -+}; -+ -+static struct resource usr8200_uart_resources [] = { -+ { -+ .start = IXP4XX_UART2_BASE_PHYS, -+ .end = IXP4XX_UART2_BASE_PHYS + 0x0fff, -+ .flags = IORESOURCE_MEM -+ }, -+ { -+ .start = IXP4XX_UART1_BASE_PHYS, -+ .end = IXP4XX_UART1_BASE_PHYS + 0x0fff, -+ .flags = IORESOURCE_MEM -+ } -+}; -+ -+static struct plat_serial8250_port usr8200_uart_data[] = { -+ { -+ .mapbase = IXP4XX_UART2_BASE_PHYS, -+ .membase = (char *)IXP4XX_UART2_BASE_VIRT + REG_OFFSET, -+ .irq = IRQ_IXP4XX_UART2, -+ .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST, -+ .iotype = UPIO_MEM, -+ .regshift = 2, -+ .uartclk = IXP4XX_UART_XTAL, -+ }, -+ { -+ .mapbase = IXP4XX_UART1_BASE_PHYS, -+ .membase = (char *)IXP4XX_UART1_BASE_VIRT + REG_OFFSET, -+ .irq = IRQ_IXP4XX_UART1, -+ .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST, -+ .iotype = UPIO_MEM, -+ .regshift = 2, -+ .uartclk = IXP4XX_UART_XTAL, -+ }, -+ { }, -+}; -+ -+static struct platform_device usr8200_uart = { -+ .name = "serial8250", -+ .id = PLAT8250_DEV_PLATFORM, -+ .dev = { -+ .platform_data = usr8200_uart_data, -+ }, -+ .num_resources = 2, -+ .resource = usr8200_uart_resources, -+}; -+ -+static struct gpio_led usr8200_led_pin[] = { -+ { -+ .name = "usr8200:usb1", -+ .gpio = 0, -+ .active_low = 1, -+ }, -+ { -+ .name = "usr8200:usb2", -+ .gpio = 1, -+ .active_low = 1, -+ }, -+ { -+ .name = "usr8200:ieee1394", -+ .gpio = 2, -+ .active_low = 1, -+ }, -+ { -+ .name = "usr8200:internal", -+ .gpio = 3, -+ .active_low = 1, -+ }, -+ { -+ .name = "usr8200:power", -+ .gpio = 14, -+ } -+}; -+ -+static struct gpio_led_platform_data usr8200_led_data = { -+ .num_leds = ARRAY_SIZE(usr8200_led_pin), -+ .leds = usr8200_led_pin, -+}; -+ -+static struct platform_device usr8200_led = { -+ .name = "leds-gpio", -+ .id = -1, -+ .dev.platform_data = &usr8200_led_data, -+}; -+ -+static struct eth_plat_info usr8200_plat_eth[] = { -+ { /* NPEC - LAN with Marvell 88E6060 switch */ -+ .phy = IXP4XX_ETH_PHY_MAX_ADDR, -+ .phy_mask = 0x0F0000, -+ .rxq = 4, -+ .txreadyq = 21, -+ }, { /* NPEB - WAN */ -+ .phy = 9, -+ .rxq = 3, -+ .txreadyq = 20, -+ } -+}; -+ -+static struct platform_device usr8200_eth[] = { -+ { -+ .name = "ixp4xx_eth", -+ .id = IXP4XX_ETH_NPEC, -+ .dev.platform_data = usr8200_plat_eth, -+ }, { -+ .name = "ixp4xx_eth", -+ .id = IXP4XX_ETH_NPEB, -+ .dev.platform_data = usr8200_plat_eth + 1, -+ } -+}; -+ -+static struct resource usr8200_rtc_resources = { -+ .flags = IORESOURCE_MEM -+}; -+ -+static struct platform_device usr8200_rtc = { -+ .name = "rtc7301", -+ .id = 0, -+ .num_resources = 1, -+ .resource = &usr8200_rtc_resources, -+}; -+ -+static struct platform_device *usr8200_devices[] __initdata = { -+ &usr8200_flash, -+ &usr8200_uart, -+ &usr8200_led, -+ &usr8200_eth[0], -+ &usr8200_eth[1], -+ &usr8200_rtc, -+}; -+ -+static void __init usr8200_init(void) -+{ -+ ixp4xx_sys_init(); -+ -+ usr8200_flash_resource.start = IXP4XX_EXP_BUS_BASE(0); -+ usr8200_flash_resource.end = IXP4XX_EXP_BUS_BASE(0) + SZ_16M - 1; -+ -+ usr8200_rtc_resources.start = IXP4XX_EXP_BUS_BASE(2); -+ usr8200_rtc_resources.end = IXP4XX_EXP_BUS_BASE(2) + 0x01ff; -+ -+ *IXP4XX_EXP_CS0 |= IXP4XX_FLASH_WRITABLE; -+ *IXP4XX_EXP_CS2 = 0x3fff000 | IXP4XX_EXP_BUS_SIZE(0) | IXP4XX_EXP_BUS_WR_EN | -+ IXP4XX_EXP_BUS_CS_EN | IXP4XX_EXP_BUS_BYTE_EN; -+ *IXP4XX_GPIO_GPCLKR = 0x01100000; -+ -+ /* configure button as input */ -+ gpio_line_config(12, IXP4XX_GPIO_IN); -+ -+ platform_add_devices(usr8200_devices, ARRAY_SIZE(usr8200_devices)); -+} -+ -+MACHINE_START(USR8200, "USRobotics USR8200") -+ /* Maintainer: Peter Denison <openwrt@marshadder.org> */ -+ .phys_io = IXP4XX_PERIPHERAL_BASE_PHYS, -+ .io_pg_offst = ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xfffc, -+ .map_io = ixp4xx_map_io, -+ .init_irq = ixp4xx_init_irq, -+ .timer = &ixp4xx_timer, -+ .boot_params = 0x0100, -+ .init_machine = usr8200_init, -+MACHINE_END ---- a/arch/arm/mach-ixp4xx/include/mach/uncompress.h -+++ b/arch/arm/mach-ixp4xx/include/mach/uncompress.h -@@ -43,7 +43,7 @@ static __inline__ void __arch_decomp_set - if (machine_is_adi_coyote() || machine_is_gtwx5715() || - machine_is_gateway7001() || machine_is_wg302v2() || - machine_is_pronghorn() || machine_is_pronghorn_metro() || machine_is_wrt300nv2() || -- machine_is_tw5334()) -+ machine_is_tw5334() || machine_is_usr8200()) - uart_base = (volatile u32*) IXP4XX_UART2_BASE_PHYS; - else - uart_base = (volatile u32*) IXP4XX_UART1_BASE_PHYS; diff --git a/target/linux/ixp4xx/patches-2.6.33/520-tw2662_support.patch b/target/linux/ixp4xx/patches-2.6.33/520-tw2662_support.patch deleted file mode 100644 index cc796c504..000000000 --- a/target/linux/ixp4xx/patches-2.6.33/520-tw2662_support.patch +++ /dev/null @@ -1,329 +0,0 @@ ---- a/arch/arm/mach-ixp4xx/Kconfig -+++ b/arch/arm/mach-ixp4xx/Kconfig -@@ -180,6 +180,15 @@ config ARCH_PRPMC1100 - PrPCM1100 Processor Mezanine Module. For more information on - this platform, see <file:Documentation/arm/IXP4xx>. - -+config MACH_TW2662 -+ bool "Titan Wireless TW-266-2" -+ select PCI -+ help -+ Say 'Y' here if you want your kernel to support the Titan -+ Wireless TW266-2. For more information on this platform, -+ see http://openwrt.org -+ -+ - config MACH_TW5334 - bool "Titan Wireless TW-533-4" - select PCI ---- a/arch/arm/mach-ixp4xx/Makefile -+++ b/arch/arm/mach-ixp4xx/Makefile -@@ -23,6 +23,7 @@ obj-pci-$(CONFIG_MACH_SIDEWINDER) += sid - obj-pci-$(CONFIG_MACH_COMPEX) += ixdp425-pci.o - obj-pci-$(CONFIG_MACH_WRT300NV2) += wrt300nv2-pci.o - obj-pci-$(CONFIG_MACH_AP1000) += ixdp425-pci.o -+obj-pci-$(CONFIG_MACH_TW2662) += tw2662-pci.o - obj-pci-$(CONFIG_MACH_TW5334) += tw5334-pci.o - obj-pci-$(CONFIG_MACH_MI424WR) += mi424wr-pci.o - obj-pci-$(CONFIG_MACH_USR8200) += usr8200-pci.o -@@ -48,6 +49,7 @@ obj-$(CONFIG_MACH_SIDEWINDER) += sidewin - obj-$(CONFIG_MACH_COMPEX) += compex-setup.o - obj-$(CONFIG_MACH_WRT300NV2) += wrt300nv2-setup.o - obj-$(CONFIG_MACH_AP1000) += ap1000-setup.o -+obj-$(CONFIG_MACH_TW2662) += tw2662-setup.o - obj-$(CONFIG_MACH_TW5334) += tw5334-setup.o - obj-$(CONFIG_MACH_MI424WR) += mi424wr-setup.o - obj-$(CONFIG_MACH_USR8200) += usr8200-setup.o ---- a/arch/arm/mach-ixp4xx/include/mach/uncompress.h -+++ b/arch/arm/mach-ixp4xx/include/mach/uncompress.h -@@ -43,7 +43,7 @@ static __inline__ void __arch_decomp_set - if (machine_is_adi_coyote() || machine_is_gtwx5715() || - machine_is_gateway7001() || machine_is_wg302v2() || - machine_is_pronghorn() || machine_is_pronghorn_metro() || machine_is_wrt300nv2() || -- machine_is_tw5334() || machine_is_usr8200()) -+ machine_is_tw5334() || machine_is_usr8200() || machine_is_tw2662()) - uart_base = (volatile u32*) IXP4XX_UART2_BASE_PHYS; - else - uart_base = (volatile u32*) IXP4XX_UART1_BASE_PHYS; ---- /dev/null -+++ b/arch/arm/mach-ixp4xx/tw2662-pci.c -@@ -0,0 +1,68 @@ -+/* -+ * arch/arm/mach-ixp4xx/tw2662-pci.c -+ * -+ * PCI setup routines for Tiran Wireless TW-266-2 platform -+ * -+ * Copyright (C) 2002 Jungo Software Technologies. -+ * Copyright (C) 2003 MontaVista Softwrae, Inc. -+ * Copyright (C) 2010 Alexandros C. Couloumbis <alex@ozo.com> -+ * Copyright (C) 2010 Gabor Juhos <juhosg@openwrt.org> -+ * -+ * Maintainer: Deepak Saxena <dsaxena@mvista.com> -+ * Maintainer: Alexandros C. Couloumbis <alex@ozo.com> -+ * -+ * This program is free software; you can redistribute it and/or modify -+ * it under the terms of the GNU General Public License version 2 as -+ * published by the Free Software Foundation. -+ * -+ */ -+ -+#include <linux/kernel.h> -+#include <linux/pci.h> -+#include <linux/init.h> -+#include <linux/irq.h> -+#include <asm/mach-types.h> -+#include <mach/hardware.h> -+#include <asm/irq.h> -+#include <asm/mach/pci.h> -+ -+#define SLOT0_DEVID 1 -+#define SLOT1_DEVID 3 -+ -+/* PCI controller GPIO to IRQ pin mappings */ -+#define SLOT0_INTA 11 -+#define SLOT1_INTA 9 -+ -+void __init tw2662_pci_preinit(void) -+{ -+ set_irq_type(IXP4XX_GPIO_IRQ(SLOT0_INTA), IRQ_TYPE_LEVEL_LOW); -+ set_irq_type(IXP4XX_GPIO_IRQ(SLOT1_INTA), IRQ_TYPE_LEVEL_LOW); -+ ixp4xx_pci_preinit(); -+} -+ -+static int __init tw2662_map_irq(struct pci_dev *dev, u8 slot, u8 pin) -+{ -+ if (slot == SLOT0_DEVID) -+ return IXP4XX_GPIO_IRQ(SLOT0_INTA); -+ else if (slot == SLOT1_DEVID) -+ return IXP4XX_GPIO_IRQ(SLOT1_INTA); -+ else return -1; -+} -+ -+struct hw_pci tw2662_pci __initdata = { -+ .nr_controllers = 1, -+ .preinit = tw2662_pci_preinit, -+ .swizzle = pci_std_swizzle, -+ .setup = ixp4xx_setup, -+ .scan = ixp4xx_scan_bus, -+ .map_irq = tw2662_map_irq, -+}; -+ -+int __init tw2662_pci_init(void) -+{ -+ if (machine_is_tw2662()) -+ pci_common_init(&tw2662_pci); -+ return 0; -+} -+ -+subsys_initcall(tw2662_pci_init); ---- /dev/null -+++ b/arch/arm/mach-ixp4xx/tw2662-setup.c -@@ -0,0 +1,208 @@ -+/* -+ * arch/arm/mach-ixp4xx/tw2662-setup.c -+ * -+ * Titan Wireless TW-266-2 -+ * -+ * Copyright (C) 2010 Gabor Juhos <juhosg@openwrt.org> -+ * Copyright (C) 2010 Alexandros C. Couloumbis <alex@ozo.com> -+ * -+ * based on ap1000-setup.c: -+ * Author: Imre Kaloz <Kaloz@openwrt.org> -+ */ -+ -+#include <linux/if_ether.h> -+#include <linux/kernel.h> -+#include <linux/init.h> -+#include <linux/device.h> -+#include <linux/serial.h> -+#include <linux/tty.h> -+#include <linux/serial_8250.h> -+#include <linux/slab.h> -+#include <linux/netdevice.h> -+#include <linux/etherdevice.h> -+#include <linux/platform_device.h> -+ -+#include <asm/io.h> -+#include <asm/types.h> -+#include <asm/setup.h> -+#include <asm/memory.h> -+#include <mach/hardware.h> -+#include <asm/mach-types.h> -+#include <asm/irq.h> -+#include <asm/mach/arch.h> -+#include <asm/mach/flash.h> -+ -+/* gpio mask used by platform device */ -+#define TW2662_GPIO_MASK (1 << 1) | (1 << 3) | (1 << 5) | (1 << 7) -+ -+static struct flash_platform_data tw2662_flash_data = { -+ .map_name = "cfi_probe", -+ .width = 2, -+}; -+ -+static struct resource tw2662_flash_resource = { -+ .flags = IORESOURCE_MEM, -+}; -+ -+static struct platform_device tw2662_flash = { -+ .name = "IXP4XX-Flash", -+ .id = 0, -+ .dev = { -+ .platform_data = &tw2662_flash_data, -+ }, -+ .num_resources = 1, -+ .resource = &tw2662_flash_resource, -+}; -+ -+static struct resource tw2662_gpio_resources[] = { -+ { -+ .name = "gpio", -+ /* FIXME: gpio mask should be model specific */ -+ .start = TW2662_GPIO_MASK, -+ .end = TW2662_GPIO_MASK, -+ .flags = 0, -+ }, -+}; -+ -+static struct platform_device tw2662_gpio = { -+ .name = "GPIODEV", -+ .id = -1, -+ .num_resources = ARRAY_SIZE(tw2662_gpio_resources), -+ .resource = tw2662_gpio_resources, -+}; -+ -+static struct resource tw2662_uart_resources[] = { -+ { -+ .start = IXP4XX_UART1_BASE_PHYS, -+ .end = IXP4XX_UART1_BASE_PHYS + 0x0fff, -+ .flags = IORESOURCE_MEM -+ }, -+ { -+ .start = IXP4XX_UART2_BASE_PHYS, -+ .end = IXP4XX_UART2_BASE_PHYS + 0x0fff, -+ .flags = IORESOURCE_MEM -+ } -+}; -+ -+static struct plat_serial8250_port tw2662_uart_data[] = { -+ { -+ .mapbase = IXP4XX_UART1_BASE_PHYS, -+ .membase = (char *)IXP4XX_UART1_BASE_VIRT + REG_OFFSET, -+ .irq = IRQ_IXP4XX_UART1, -+ .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST, -+ .iotype = UPIO_MEM, -+ .regshift = 2, -+ .uartclk = IXP4XX_UART_XTAL, -+ }, -+ { -+ .mapbase = IXP4XX_UART2_BASE_PHYS, -+ .membase = (char *)IXP4XX_UART2_BASE_VIRT + REG_OFFSET, -+ .irq = IRQ_IXP4XX_UART2, -+ .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST, -+ .iotype = UPIO_MEM, -+ .regshift = 2, -+ .uartclk = IXP4XX_UART_XTAL, -+ }, -+ { }, -+}; -+ -+static struct platform_device tw2662_uart = { -+ .name = "serial8250", -+ .id = PLAT8250_DEV_PLATFORM, -+ .dev.platform_data = tw2662_uart_data, -+ .num_resources = 2, -+ .resource = tw2662_uart_resources -+}; -+ -+/* Built-in 10/100 Ethernet MAC interfaces */ -+static struct eth_plat_info tw2662_plat_eth[] = { -+ { -+ .phy = 3, -+ .rxq = 3, -+ .txreadyq = 20, -+ }, { -+ .phy = 1, -+ .rxq = 4, -+ .txreadyq = 21, -+ } -+}; -+ -+static struct platform_device tw2662_eth[] = { -+ { -+ .name = "ixp4xx_eth", -+ .id = IXP4XX_ETH_NPEB, -+ .dev.platform_data = tw2662_plat_eth, -+ }, { -+ .name = "ixp4xx_eth", -+ .id = IXP4XX_ETH_NPEC, -+ .dev.platform_data = tw2662_plat_eth + 1, -+ } -+}; -+ -+ -+static struct platform_device *tw2662_devices[] __initdata = { -+ &tw2662_flash, -+ &tw2662_uart, -+ &tw2662_gpio, -+ &tw2662_eth[0], -+ &tw2662_eth[1], -+}; -+ -+static char tw2662_mem_fixup[] __initdata = "mem=64M "; -+ -+static void __init tw2662_fixup(struct machine_desc *desc, -+ struct tag *tags, char **cmdline, struct meminfo *mi) -+ -+{ -+ struct tag *t = tags; -+ char *p = *cmdline; -+ -+ /* Find the end of the tags table, taking note of any cmdline tag. */ -+ for (; t->hdr.size; t = tag_next(t)) { -+ if (t->hdr.tag == ATAG_CMDLINE) { -+ p = t->u.cmdline.cmdline; -+ } -+ } -+ -+ /* Overwrite the end of the table with a new cmdline tag. */ -+ t->hdr.tag = ATAG_CMDLINE; -+ t->hdr.size = (sizeof (struct tag_header) + -+ strlen(tw2662_mem_fixup) + strlen(p) + 1 + 4) >> 2; -+ strlcpy(t->u.cmdline.cmdline, tw2662_mem_fixup, COMMAND_LINE_SIZE); -+ strlcpy(t->u.cmdline.cmdline + strlen(tw2662_mem_fixup), p, -+ COMMAND_LINE_SIZE - strlen(tw2662_mem_fixup)); -+ -+ /* Terminate the table. */ -+ t = tag_next(t); -+ t->hdr.tag = ATAG_NONE; -+ t->hdr.size = 0; -+} -+ -+static void __init tw2662_init(void) -+{ -+ ixp4xx_sys_init(); -+ -+ tw2662_flash_resource.start = IXP4XX_EXP_BUS_BASE(0); -+ tw2662_flash_resource.end = -+ IXP4XX_EXP_BUS_BASE(0) + ixp4xx_exp_bus_size - 1; -+ -+ platform_add_devices(tw2662_devices, ARRAY_SIZE(tw2662_devices)); -+ /* hack MACs as most of these boards have a broken eeprom */ -+ random_ether_addr(tw2662_plat_eth[0].hwaddr); -+ random_ether_addr(tw2662_plat_eth[1].hwaddr); -+ -+} -+ -+#ifdef CONFIG_MACH_TW2662 -+MACHINE_START(TW2662, "Titan Wireless TW-266-2") -+ /* Maintainer: Alexandros C. Couloumbis <alex@ozo.com> */ -+ .phys_io = IXP4XX_PERIPHERAL_BASE_PHYS, -+ .io_pg_offst = ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xfffc, -+ .fixup = tw2662_fixup, -+ .map_io = ixp4xx_map_io, -+ .init_irq = ixp4xx_init_irq, -+ .timer = &ixp4xx_timer, -+ .boot_params = 0x0100, -+ .init_machine = tw2662_init, -+MACHINE_END -+#endif diff --git a/target/linux/ixp4xx/patches-2.6.33/600-skb_avoid_dmabounce.patch b/target/linux/ixp4xx/patches-2.6.33/600-skb_avoid_dmabounce.patch deleted file mode 100644 index 026c717c7..000000000 --- a/target/linux/ixp4xx/patches-2.6.33/600-skb_avoid_dmabounce.patch +++ /dev/null @@ -1,13 +0,0 @@ ---- a/net/core/skbuff.c -+++ b/net/core/skbuff.c -@@ -264,6 +264,10 @@ struct sk_buff *__alloc_skb(unsigned int - if (!skb) - goto out; - -+#ifdef CONFIG_ARCH_IXP4XX -+ gfp_mask |= GFP_DMA; -+#endif -+ - size = SKB_DATA_ALIGN(size); - data = kmalloc_node_track_caller(size + sizeof(struct skb_shared_info), - gfp_mask, node); diff --git a/target/linux/ixp4xx/patches-2.6.33/601-arm-dma_free_coherent.patch b/target/linux/ixp4xx/patches-2.6.33/601-arm-dma_free_coherent.patch deleted file mode 100644 index b939705b5..000000000 --- a/target/linux/ixp4xx/patches-2.6.33/601-arm-dma_free_coherent.patch +++ /dev/null @@ -1,12 +0,0 @@ ---- a/arch/arm/mm/dma-mapping.c -+++ b/arch/arm/mm/dma-mapping.c -@@ -384,7 +384,8 @@ EXPORT_SYMBOL(dma_mmap_writecombine); - */ - void dma_free_coherent(struct device *dev, size_t size, void *cpu_addr, dma_addr_t handle) - { -- WARN_ON(irqs_disabled()); -+ if (irqs_disabled()) /* don't want stack dumps for these! */ -+ printk("WARNING: at %s:%d %s()\n", __FILE__, __LINE__, __FUNCTION__); - - if (dma_release_from_coherent(dev, get_order(size), cpu_addr)) - return; diff --git a/target/linux/ixp4xx/patches-2.6.33/603-arm-kluin-array-indexing.patch b/target/linux/ixp4xx/patches-2.6.33/603-arm-kluin-array-indexing.patch deleted file mode 100644 index aca693a41..000000000 --- a/target/linux/ixp4xx/patches-2.6.33/603-arm-kluin-array-indexing.patch +++ /dev/null @@ -1,33 +0,0 @@ ---- a/arch/arm/kernel/setup.c -+++ b/arch/arm/kernel/setup.c -@@ -322,12 +322,13 @@ static void __init setup_processor(void) - void cpu_init(void) - { - unsigned int cpu = smp_processor_id(); -- struct stack *stk = &stacks[cpu]; -+ struct stack *stk; - - if (cpu >= NR_CPUS) { - printk(KERN_CRIT "CPU%u: bad primary CPU number\n", cpu); - BUG(); - } -+ stk = &stacks[cpu]; - - /* - * Define the placement constraint for the inline asm directive below. -@@ -386,13 +387,14 @@ static struct machine_desc * __init setu - - static int __init arm_add_memory(unsigned long start, unsigned long size) - { -- struct membank *bank = &meminfo.bank[meminfo.nr_banks]; -+ struct membank *bank; - - if (meminfo.nr_banks >= NR_BANKS) { - printk(KERN_CRIT "NR_BANKS too low, " - "ignoring memory at %#lx\n", start); - return -EINVAL; - } -+ bank = &meminfo.bank[meminfo.nr_banks]; - - /* - * Ensure that start/size are aligned to a page boundary. diff --git a/target/linux/ixp4xx/patches-2.6.33/604-arm-ixp4xx-sched_clock.patch b/target/linux/ixp4xx/patches-2.6.33/604-arm-ixp4xx-sched_clock.patch deleted file mode 100644 index 43cbaa2ae..000000000 --- a/target/linux/ixp4xx/patches-2.6.33/604-arm-ixp4xx-sched_clock.patch +++ /dev/null @@ -1,20 +0,0 @@ ---- a/arch/arm/mach-ixp4xx/common.c -+++ b/arch/arm/mach-ixp4xx/common.c -@@ -466,6 +466,17 @@ static void __init ixp4xx_clocksource_in - } - - /* -+ * sched_clock() -+ */ -+unsigned long long sched_clock(void) -+{ -+ cycle_t cyc = ixp4xx_get_cycles(NULL); -+ struct clocksource *cs = &clocksource_ixp4xx; -+ -+ return clocksource_cyc2ns(cyc, cs->mult, cs->shift); -+} -+ -+/* - * clockevents - */ - static int ixp4xx_set_next_event(unsigned long evt, diff --git a/target/linux/ixp4xx/patches-2.6.33/605-arm-rmk-cache-flush-optim.patch b/target/linux/ixp4xx/patches-2.6.33/605-arm-rmk-cache-flush-optim.patch deleted file mode 100644 index 31e0fb531..000000000 --- a/target/linux/ixp4xx/patches-2.6.33/605-arm-rmk-cache-flush-optim.patch +++ /dev/null @@ -1,11 +0,0 @@ ---- a/arch/arm/mm/fault-armv.c -+++ b/arch/arm/mm/fault-armv.c -@@ -127,8 +127,6 @@ make_coherent(struct address_space *mapp - flush_dcache_mmap_unlock(mapping); - if (aliases) - adjust_pte(vma, addr); -- else -- flush_cache_page(vma, addr, pfn); - } - - /* |