diff options
Diffstat (limited to 'target/linux/etrax/files/arch/cris')
4 files changed, 0 insertions, 1503 deletions
diff --git a/target/linux/etrax/files/arch/cris/arch-v10/drivers/etraxi2c.h b/target/linux/etrax/files/arch/cris/arch-v10/drivers/etraxi2c.h deleted file mode 100644 index 9d5c9bf95..000000000 --- a/target/linux/etrax/files/arch/cris/arch-v10/drivers/etraxi2c.h +++ /dev/null @@ -1,49 +0,0 @@ -#ifndef _LINUX_ETRAXI2C_H -#define _LINUX_ETRAXI2C_H - -/* etraxi2c _IOC_TYPE, bits 8 to 15 in ioctl cmd */ - -#define ETRAXI2C_IOCTYPE 44 - -/* supported ioctl _IOC_NR's */ - -/* in write operations, the argument contains both i2c - * slave, register and value. - */ - -#define I2C_WRITEARG(slave, reg, value) (((slave) << 16) | ((reg) << 8) | (value)) -#define I2C_READARG(slave, reg) (((slave) << 16) | ((reg) << 8)) - -#define I2C_ARGSLAVE(arg) ((arg) >> 16) -#define I2C_ARGREG(arg) (((arg) >> 8) & 0xff) -#define I2C_ARGVALUE(arg) ((arg) & 0xff) - -#define I2C_WRITEREG 0x1 /* write to an I2C register */ -#define I2C_READREG 0x2 /* read from an I2C register */ - -/* -EXAMPLE usage: - - i2c_arg = I2C_WRITEARG(STA013_WRITE_ADDR, reg, val); - ioctl(fd, _IO(ETRAXI2C_IOCTYPE, I2C_WRITEREG), i2c_arg); - - i2c_arg = I2C_READARG(STA013_READ_ADDR, reg); - val = ioctl(fd, _IO(ETRAXI2C_IOCTYPE, I2C_READREG), i2c_arg); - -*/ - -/* Extended part */ -#define I2C_READ 0x4 /* reads from I2C device */ -#define I2C_WRITE 0x3 /* writes to I2C device */ -#define I2C_WRITEREAD 0x5 /* writes to I2C device where to start reading */ - -typedef struct _I2C_DATA -{ - unsigned char slave; /* I2C address (8-bit representation) of slave device */ - unsigned char wbuf[256]; /* Write buffer (length = 256 bytes) */ - unsigned int wlen; /* Number of bytes to write from wbuf[] */ - unsigned char rbuf[256]; /* Read buffer (length = 256 bytes) */ - unsigned int rlen; /* Number of bytes to read into rbuf[] */ -} I2C_DATA; - -#endif diff --git a/target/linux/etrax/files/arch/cris/arch-v10/drivers/i2c_errno.h b/target/linux/etrax/files/arch/cris/arch-v10/drivers/i2c_errno.h deleted file mode 100644 index ddd99b0e5..000000000 --- a/target/linux/etrax/files/arch/cris/arch-v10/drivers/i2c_errno.h +++ /dev/null @@ -1,20 +0,0 @@ -#ifndef _I2C_ERRNO_H -#define _I2C_ERRNO_H - -#define EI2CNOERRORS 0 /* All fine */ -#define EI2CBUSNFREE 1 /* I2C bus not free */ -#define EI2CWADDRESS 2 /* Address write failed */ -#define EI2CRADDRESS 3 /* Address read failed */ -#define EI2CSENDDATA 4 /* Sending data failed */ -#define EI2CRECVDATA 5 /* Receiving data failed */ -#define EI2CSTRTCOND 6 /* Start condition failed */ -#define EI2CRSTACOND 7 /* Repeated start condition failed */ -#define EI2CSTOPCOND 8 /* Stop condition failed */ -#define EI2CNOSNDBYT 9 /* Number of send bytes is 0, while there's a send buffer defined */ -#define EI2CNOSNDBUF 10 /* No send buffer defined, while number of send bytes is not 0 */ -#define EI2CNORCVBYT 11 /* Number of receive bytes is 0, while there's a receive buffer defined */ -#define EI2CNORCVBUF 12 /* No receive buffer defined, while number of receive bytes is not 0 */ -#define EI2CNOACKNLD 13 /* No acknowledge received from slave */ -#define EI2CNOMNUMBR 14 /* No MAJOR number received from kernel while registering the device */ - -#endif /* _I2C_ERRNO_H */ diff --git a/target/linux/etrax/files/arch/cris/arch-v10/drivers/i2c_gvc.c b/target/linux/etrax/files/arch/cris/arch-v10/drivers/i2c_gvc.c deleted file mode 100644 index e47bc6459..000000000 --- a/target/linux/etrax/files/arch/cris/arch-v10/drivers/i2c_gvc.c +++ /dev/null @@ -1,1404 +0,0 @@ -/*!*************************************************************************** -*! -*! FILE NAME : i2c.c -*! -*! -*! --------------------------------------------------------------------------- -*! -*! ( C ) Copyright 1999-2002 Axis Communications AB, LUND, SWEDEN -*! -*!***************************************************************************/ - -/******************** INCLUDE FILES SECTION ****************************/ - -#include <linux/module.h> -#include <linux/fs.h> - -#ifdef CONFIG_ETRAX_I2C_DYN_ALLOC -#include <linux/types.h> /* for dev_t */ -#include <linux/cdev.h> /* for struct cdev */ -#endif - -#include <linux/device.h> - -#include "etraxi2c.h" - -#include "i2c_errno.h" - -#include <asm/io.h> -#include <asm/delay.h> -#include <asm/arch/io_interface_mux.h> -#include <asm/uaccess.h> - -#include "i2c_gvc.h" - -MODULE_DESCRIPTION( "I2C Device Driver - 2.3" ); - -/*!********************************************************************* - *!History I2C driver Geert Vancompernolle - *!--------------------------------------- - *! - *! - v1.0: - *! First official version. - *! - *! - v1.1: - *! Changes to remove unwanted spikes at ACK/NACK time. - *! - *!*********************************************************************/ - -MODULE_LICENSE( "GPL" ); - -/****************** MACRO's **********************/ - -#define D( x ) - -#ifndef CONFIG_ETRAX_I2C_DYN_ALLOC -#define I2C_MAJOR 123 /* LOCAL/EXPERIMENTAL */ -#endif - -#define WAITONEUS 1 -/* Following are abbreviations taken from Philips I2C standard */ -/* Values are representing time in us and are rounded to next whole number, if relevant */ -#define THDSTA 4 /* Hold delay time for (repeated) START condition */ -#define TLOW 5 /* LOW period of the SCL clock */ -#define THDDAT 1 /* Hold delay time for DATA: value of 0 is allowed but 1 taken to be sure */ -#define TSUDAT 1 /* Set-up time for DATA */ -#define THIGH 4 /* HIGH period of the SCL clock */ -#define TSUSTA 5 /* Set-up time for a repeated START condition */ -#define TSUSTO 4 /* Set-up time for STOP condition */ -#define TBUF 5 /* Bus-free time between STOP and START condition */ - -#ifdef CONFIG_ETRAX_I2C_SLAVE_DELAY -#define MAXSCLRETRIES 100 -#endif - -#define MAXBUSFREERETRIES 5 -#define MAXRETRIES 3 -#define WRITEADDRESS_MASK ( 0xFE ) -#define READADDRESS_MASK ( 0x01 ) - -#define SCL_HIGH 1 -#define SCL_LOW 0 -#define SDA_HIGH 1 -#define SDA_LOW 0 - -#ifdef CONFIG_ETRAX_I2C_USES_PB_NOT_PB_I2C -/* Use PB and not PB_I2C */ -#ifndef CONFIG_ETRAX_I2C_DATA_PORT -#define CONFIG_ETRAX_I2C_DATA_PORT 0 -#endif -#ifndef CONFIG_ETRAX_I2C_CLK_PORT -#define CONFIG_ETRAX_I2C_CLK_PORT 1 -#endif - -#define SDABIT CONFIG_ETRAX_I2C_DATA_PORT -#define SCLBIT CONFIG_ETRAX_I2C_CLK_PORT -#define i2c_enable() -#define i2c_disable() - -/* enable or disable output-enable, to select output or input on the i2c bus */ -#define i2c_sda_dir_out() \ - REG_SHADOW_SET( R_PORT_PB_DIR, port_pb_dir_shadow, SDABIT, 1 ) -#define i2c_sda_dir_in() \ - REG_SHADOW_SET( R_PORT_PB_DIR, port_pb_dir_shadow, SDABIT, 0 ) - -#ifdef CONFIG_ETRAX_I2C_SLAVE_DELAY -#define i2c_scl_dir_out() \ - REG_SHADOW_SET( R_PORT_PB_DIR, port_pb_dir_shadow, SCLBIT, 1 ) -#define i2c_scl_dir_in() \ - REG_SHADOW_SET( R_PORT_PB_DIR, port_pb_dir_shadow, SCLBIT, 0 ) -#endif - -/* control the i2c clock and data signals */ -#define i2c_set_scl( x ) \ - REG_SHADOW_SET( R_PORT_PB_DATA, port_pb_data_shadow, SCLBIT, x ) -#define i2c_set_sda( x ) \ - REG_SHADOW_SET( R_PORT_PB_DATA, port_pb_data_shadow, SDABIT, x ) - -/* read status of SDA bit from the i2c interface */ -#define i2c_sda_is_high() ( ( ( *R_PORT_PB_READ & ( 1 << SDABIT ) ) ) >> SDABIT ) - -/* read status of SCL bit from the i2c interface */ -#define i2c_scl_is_high() ( ( ( *R_PORT_PB_READ & ( 1 << SCLBIT ) ) ) >> SCLBIT ) - -#else -/* enable or disable the i2c interface */ -#define i2c_enable() *R_PORT_PB_I2C = ( port_pb_i2c_shadow |= IO_MASK( R_PORT_PB_I2C, i2c_en ) ) -#define i2c_disable() *R_PORT_PB_I2C = ( port_pb_i2c_shadow &= ~IO_MASK( R_PORT_PB_I2C, i2c_en ) ) - -/* enable or disable output-enable, to select output or input on the i2c bus */ -#define i2c_sda_dir_out() \ - *R_PORT_PB_I2C = ( port_pb_i2c_shadow &= ~IO_MASK( R_PORT_PB_I2C, i2c_oe_ ) ); \ - REG_SHADOW_SET( R_PORT_PB_DIR, port_pb_dir_shadow, 0, 1 ); -#define i2c_sda_dir_in() \ - *R_PORT_PB_I2C = ( port_pb_i2c_shadow |= IO_MASK( R_PORT_PB_I2C, i2c_oe_ ) ); \ - REG_SHADOW_SET( R_PORT_PB_DIR, port_pb_dir_shadow, 0, 0 ); - -/* control the i2c clock and data signals */ -#define i2c_set_scl( x ) \ - *R_PORT_PB_I2C = ( port_pb_i2c_shadow = ( port_pb_i2c_shadow & \ - ~IO_MASK( R_PORT_PB_I2C, i2c_set_scl ) ) | IO_FIELD( R_PORT_PB_I2C, i2c_set_scl, ( x ) ) ); \ - REG_SHADOW_SET( R_PORT_PB_DATA, port_pb_data_shadow, 1, x ); - -#define i2c_set_sda( x ) \ - *R_PORT_PB_I2C = ( port_pb_i2c_shadow = ( port_pb_i2c_shadow & \ - ~IO_MASK( R_PORT_PB_I2C, i2c_d ) ) | IO_FIELD( R_PORT_PB_I2C, i2c_d, ( x ) ) ); \ - REG_SHADOW_SET( R_PORT_PB_DATA, port_pb_data_shadow, 0, x ); - -/* read a bit from the i2c interface */ -#define i2c_sda_is_high() ( *R_PORT_PB_READ & 0x1 ) -#endif - -/* use the kernels delay routine */ -#define i2c_delay( usecs ) udelay( usecs ) - - -/****************** TYPEDEF's **********************/ - - -/****************** STATIC (file scope) VARIABLES **********************/ -static DEFINE_SPINLOCK( i2c_lock ); /* Protect directions etc */ -static const char i2c_name[] = "i2c"; - - - -/****************** PROTOTYPING SECTION *************************/ -static int i2c_open( struct inode *inode, struct file *filp ); -static int i2c_release( struct inode *inode, struct file *filp ); -static int i2c_command( unsigned char slave - , unsigned char* wbuf - , unsigned char wlen - , unsigned char* rbuf - , unsigned char rlen - ); -static int i2c_bus_free_check( unsigned char maxretries ); -static void i2c_finalise( const char* text, unsigned long irqflags ); - - -/************************************************************************/ -/****************** AUXILIARIES *************************/ -/************************************************************************/ - -/*#--------------------------------------------------------------------------- - *# - *# FUNCTION NAME: i2c_open - *# - *# DESCRIPTION : opens an I2C device - *# - *# PARAMETERS : *inode: reference to inode - *# *filp : reference to file pointer - *# - *#--------------------------------------------------------------------------- - */ -static int i2c_open( struct inode *inode, struct file *filp ) -{ - return 0; -} /* i2c_open */ - - -/*#--------------------------------------------------------------------------- - *# - *# FUNCTION NAME: i2c_release - *# - *# DESCRIPTION : Releases the I2C device - *# - *# PARAMETERS : *inode: reference to inode - *# *filp : reference to file pointer - *# - *#--------------------------------------------------------------------------- - */ -static int i2c_release( struct inode *inode, struct file *filp ) -{ - return 0; -} /* i2c_release */ - - -/*#--------------------------------------------------------------------------- - *# - *# FUNCTION NAME: i2c_ioctl - *# - *# DESCRIPTION : Main device API: ioctl's to write/read - *# to/from i2c registers - *# - *# PARAMETERS : *inode: reference to inode - *# *filp : reference to file pointer - *# cmd : command to be executed during the ioctl call - *# arg : pointer to a structure with the data??? - *# - *# RETURN : result of the ioctl call - *# - *#--------------------------------------------------------------------------- - */ -static int i2c_ioctl( struct inode *inode - , struct file *file - , unsigned int cmd - , unsigned long arg - ) -{ - /* the acme ioctls */ - I2C_DATA i2cdata; - int RetVal = EI2CNOERRORS; - - if ( _IOC_TYPE( cmd ) != ETRAXI2C_IOCTYPE ) - { - return ( -EINVAL ); - } - - switch ( _IOC_NR( cmd ) ) - { - case I2C_WRITEREG: - /* write to an i2c slave */ - RetVal = i2c_writereg( I2C_ARGSLAVE( arg ) - , I2C_ARGREG( arg ) - , I2C_ARGVALUE( arg ) - ); - break; - - case I2C_READREG: - RetVal = i2c_readreg( I2C_ARGSLAVE( arg ), I2C_ARGREG( arg ) ); - break; - - /* New functions added by GVC */ - case I2C_READ: - copy_from_user( (char*)&i2cdata, (char*)arg, sizeof( I2C_DATA ) ); - { - int RetryCntr = MAXRETRIES; - - do - { - RetVal = i2c_command( i2cdata.slave - , NULL - , 0 - , i2cdata.rbuf - , i2cdata.rlen - ); - } while ( ( EI2CNOERRORS != RetVal ) - &&( --RetryCntr ) - ); - } - copy_to_user( (char*)arg, (char*)&i2cdata, sizeof( I2C_DATA ) ); - break; - - case I2C_WRITE: - copy_from_user( (char*)&i2cdata, (char*)arg, sizeof( I2C_DATA ) ); - { - int RetryCntr = MAXRETRIES; - - do - { - RetVal = i2c_command( i2cdata.slave - , i2cdata.wbuf - , i2cdata.wlen - , NULL - , 0 - ); - } while ( ( EI2CNOERRORS != RetVal ) - &&( --RetryCntr ) - ); - } - break; - - case I2C_WRITEREAD: - copy_from_user( (char*)&i2cdata, (char*)arg, sizeof( I2C_DATA ) ); - { - int RetryCntr = MAXRETRIES; - - do - { - RetVal = i2c_command( i2cdata.slave - , i2cdata.wbuf - , i2cdata.wlen - , i2cdata.rbuf - , i2cdata.rlen - ); - } while ( ( EI2CNOERRORS != RetVal ) - &&( --RetryCntr ) - ); - } - copy_to_user( (char*)arg, (char*)&i2cdata, sizeof( I2C_DATA ) ); - break; - - default: - RetVal = -EINVAL; - } - - return ( -RetVal ); -} /* i2c_ioctl */ - - -/*#--------------------------------------------------------------------------- - *# - *# FUNCTION NAME: i2c_command - *# - *# DESCRIPTION : general routine to read/write bytes from an I2C device - *# - *# 'i2c_command()' sends wlen bytes to the I2c bus and receives - *# rlen bytes from the I2c bus. - *# The data to be send must be placed in wbuf[ 0 ] upto wbuf[ wlen - 1 ). - *# The data to be received is assembled in rbuf[ 0 ] upto rbuf[ rlen - 1 ]. - *# - *# If no data is to be sent or received, put appropriate buffer parameter - *# to "NULL" and appropriate length parameter to "0". - *# - *# PARAMETERS : slave = slave address of the I2C device - *# wbuf = address of first element of write buffer (wbuf) - *# wlen = number of bytes to be written to slave - *# rbuf = address of first element of read buffer (rbuf) - *# rlen = number of bytes to be read from slave - *# - *# RETURN : - *# EI2CNOERRORS: I2C communication went fine - *# EI2CBUSNFREE: I2C bus is not free - *# EI2CWADDRESS: I2C write address failed - *# EI2CRADDRESS: I2C read address failed - *# EI2CSENDDATA: I2C send data failed - *# EI2CRECVDATA: I2C receive data failed - *# EI2CSTRTCOND: I2C start condition failed - *# EI2CRSTACOND: I2C repeated start condition failed - *# EI2CSTOPCOND: I2C stop condition failed - *# EI2CNOSNDBYT: I2C no bytes to be sent - *# EI2CNOSNDBUF: I2C no send buffer defined - *# EI2CNORCVBYT: I2C no bytes to be received - *# EI2CNORCVBUF: I2C no receive buffer defined - *# EI2CNOACKNLD: I2C no acknowledge received - *# - *# REMARK : - *# First, the send part is completed. - *# In the send routine, there is no stop generated. This is because maybe - *# a repeated start condition must be generated. - *# This happens when we want to receive some data from the I2c bus. If not, - *# at the end of the general I2c loop the stopcondition is generated. - *# If, on the contrary, there are a number of bytes to be received, a new - *# startcondition is generated in the 'if' part of the main I2c routine, - *# which controls the receiving part. - *# Only when the receiving of data is finished, a final stopcondition is - *# generated. - *# - *#--------------------------------------------------------------------------- - */ -static int i2c_command( unsigned char slave - , unsigned char* wbuf - , unsigned char wlen - , unsigned char* rbuf - , unsigned char rlen - ) -{ - /* Check arguments and report error if relevant... */ - if ( ( wlen > 0 ) && ( wbuf == NULL ) ) - { - printk( KERN_DEBUG "I2C: EI2CNOSNDBUF\n" ); - return ( EI2CNOSNDBUF ); - } - else if ( ( wlen == 0 ) && ( wbuf != NULL ) ) - { - printk( KERN_DEBUG "I2C: EI2CNOSNDBYT\n" ); - return ( EI2CNOSNDBYT ); - } - else if ( ( rlen > 0 ) && ( rbuf == NULL ) ) - { - printk( KERN_DEBUG "I2C: EI2CNORCVBUF\n" ); - return ( EI2CNORCVBUF ); - } - else if ( ( rlen == 0 ) && ( rbuf != NULL ) ) - { - printk( KERN_DEBUG "I2C: EI2CNORCVBYT\n" ); - return ( EI2CNORCVBYT ); - } - else if ( EI2CBUSNFREE == i2c_bus_free_check( MAXBUSFREERETRIES ) ) - { - /* There's no need to try more, since we weren't even - * able to start the I2C communication. - * So, no IRQ flags are stored yet, no changes to any other - * stuff like START, STOP, SENDBYTES... - * Result, simply write down the error and return the correct error code. - */ - printk( KERN_DEBUG "I2C: EI2CBUSNFREE\n" ); - return ( EI2CBUSNFREE ); - } - else - { - /* Finally... We made it... */ - unsigned long irqflags = 0; - - /* we don't like to be interrupted */ - local_irq_save( irqflags ); - - /* Check if there are bytes to be send, - * or if you immediately want to receive data. - */ - if ( 0 < wlen ) - { - /* start I2C communication */ - if ( EI2CNOERRORS != i2c_start() ) - { - return ( i2c_finalise( "I2C: EI2CSTRTCOND\n", irqflags ) - , EI2CSTRTCOND - ); - } - - /* send slave address: xxxxxxx0B (last bit must be zero) */ - if ( EI2CNOERRORS != i2c_outbyte( slave & WRITEADDRESS_MASK ) ) - { - return ( i2c_finalise( "I2C: EI2CWADDRESS\n", irqflags ) - , EI2CWADDRESS - ); - } - - while ( wlen-- ) - { - /* send register data */ - if ( EI2CNOERRORS != i2c_outbyte( *wbuf ) && wlen ) - { - return ( i2c_finalise( "I2C: EI2CSENDDATA\n", irqflags ) - , EI2CSENDDATA - ); - } - - wbuf++; - }; - - i2c_delay( TLOW ); - } - - /* - * Receiving data from I2c_bus - * If there are bytes to be received, a new start condition is - * generated => Repeated Startcondition. - * A final stopcondition is generated at the end of the main I2c - * routine. - */ - if ( 0 < rlen ) - { - /* - * Generate start condition if wlen == 0 - * or repeated start condition if wlen != 0... - */ - if ( EI2CNOERRORS != i2c_start() ) - { - return ( i2c_finalise( ( ( 0 < wlen ) - ? "I2C: EI2CRSTACOND\n" - : "I2C: EI2CSTRTCOND\n" - ) - , irqflags - ) - , ( ( 0 < wlen ) ? EI2CRSTACOND : EI2CSTRTCOND ) - ); - } - - /* Send ReadAddress: xxxxxxx1B (last bit must be one) */ - if ( EI2CNOERRORS != i2c_outbyte( slave | READADDRESS_MASK ) ) - { - return ( i2c_finalise( "I2C: EI2CRADDRESS\n", irqflags ) - , EI2CRADDRESS - ); - } - - while ( rlen-- ) - { - /* fetch register */ - *rbuf = i2c_inbyte(); - rbuf++; - - /* last received byte needs to be NACK-ed instead of ACK-ed */ - if ( rlen ) - { - i2c_sendack(); - } - else - { - i2c_sendnack(); - } - }; - } - - /* Generate final stop condition */ - if ( EI2CNOERRORS != i2c_stop() ) - { - return ( i2c_finalise( "I2C CMD: EI2CSTOPCOND\n", irqflags ) - , EI2CSTOPCOND - ); - } - - /* enable interrupt again */ - local_irq_restore( irqflags ); - } - - return ( EI2CNOERRORS ); -} /* i2c_command */ - - -/*#--------------------------------------------------------------------------- - *# - *# FUNCTION NAME: i2c_bus_free_check - *# - *# DESCRIPTION : checks if the I2C bus is free before starting - *# an I2C communication - *# - *# PARAMETERS : maxretries, the number of times we will try to release - *# the I2C bus - *# - *# RETURN : I2cStatus_I2cBusNotFreeError in case the bus is not free, - *# I2cStatus_I2cNoError otherwise - *# - *#--------------------------------------------------------------------------- - */ -static int i2c_bus_free_check( unsigned char maxretries ) -{ - i2c_sda_dir_in(); /* Release SDA line */ - i2c_set_scl( SCL_HIGH ); /* put SCL line high */ - - i2c_delay( WAITONEUS ); - - while ( ( !i2c_sda_is_high() || !i2c_scl_is_high() ) - &&( maxretries-- ) - ) - { - /* Try to release I2C bus by generating STOP conditions */ - i2c_stop(); - } - - if ( 0 == maxretries ) - { - printk( KERN_DEBUG "I2C: EI2CBUSNFREE\n" ); - return ( EI2CBUSNFREE ); - } - else - { - return ( EI2CNOERRORS ); - } -} /* i2c_bus_free_check */ - - -static void i2c_finalise( const char* errortxt - , unsigned long irqflags - ) -{ - printk( KERN_DEBUG "%s", errortxt ); - local_irq_restore( irqflags ); - /* The least we can do when things go terribly wrong, - * is to try to release the bus. - * If this fails, well, then I don't know - * what I can do more for the moment... - */ - (void)i2c_bus_free_check( MAXBUSFREERETRIES ); -} /* i2c_finalise */ - - -static struct file_operations i2c_fops = -{ - .owner = THIS_MODULE -, .ioctl = i2c_ioctl -, .open = i2c_open -, .release = i2c_release -}; - - -/***********************************************************************/ -/************* EXTERNAL FUNCTION DEFINITION SECTION ********************/ -/***********************************************************************/ - -/*#--------------------------------------------------------------------------- - *# - *# FUNCTION NAME: i2c_init - *# - *# DESCRIPTION : initialises the I2C device driver - *# - *# PARAMETERS : - *# - *#--------------------------------------------------------------------------- - */ -int __init i2c_init( void ) -{ - static int res = 0; - static int first = 1; - - if ( !first ) - { - return res; - } - - first = 0; - - /* Setup and enable the Port B I2C interface */ - -#ifndef CONFIG_ETRAX_I2C_USES_PB_NOT_PB_I2C - /* here, we're using the dedicated I2C pins of FoxBoard */ - if ( ( res = cris_request_io_interface( if_i2c, "I2C" ) ) ) - { - printk( KERN_CRIT "i2c_init: Failed to get IO interface\n" ); - return res; - } - - *R_PORT_PB_I2C = port_pb_i2c_shadow |= - IO_STATE( R_PORT_PB_I2C, i2c_en, on ) | - IO_FIELD( R_PORT_PB_I2C, i2c_d, 1 ) | - IO_FIELD( R_PORT_PB_I2C, i2c_set_scl, 1 ) | - IO_STATE( R_PORT_PB_I2C, i2c_oe_, enable ); - - port_pb_dir_shadow &= ~IO_MASK( R_PORT_PB_DIR, dir0 ); - port_pb_dir_shadow &= ~IO_MASK( R_PORT_PB_DIR, dir1 ); - - *R_PORT_PB_DIR = ( port_pb_dir_shadow |= - IO_STATE( R_PORT_PB_DIR, dir0, input ) | - IO_STATE( R_PORT_PB_DIR, dir1, output ) ); -#else - /* If everything goes fine, res = 0, meaning "if" fails => - * will do the "else" too and as such initialise the clock port... - * Clever trick! - */ - if ( ( res = cris_io_interface_allocate_pins( if_i2c - , 'b' - , CONFIG_ETRAX_I2C_DATA_PORT - , CONFIG_ETRAX_I2C_DATA_PORT - ) - ) - ) - { - printk( KERN_WARNING "i2c_init: Failed to get IO pin for I2C data port\n" ); - return ( res ); - } - /* Same here...*/ - else if ( ( res = cris_io_interface_allocate_pins( if_i2c - , 'b' - , CONFIG_ETRAX_I2C_CLK_PORT - , CONFIG_ETRAX_I2C_CLK_PORT - ) - ) - ) - { - cris_io_interface_free_pins( if_i2c - , 'b' - , CONFIG_ETRAX_I2C_DATA_PORT - , CONFIG_ETRAX_I2C_DATA_PORT - ); - printk( KERN_WARNING "i2c_init: Failed to get IO pin for I2C clk port\n" ); - } -#endif - - return ( res ); -} /* i2c_init */ - - -/*#--------------------------------------------------------------------------- - *# - *# FUNCTION NAME: i2c_register - *# - *# DESCRIPTION : this registers the i2c driver as a character device - *# - *# PARAMETERS : - *# - *#--------------------------------------------------------------------------- - */ - -static struct class *i2c_class; - -static int __init i2c_register( void ) -{ - int res; -#ifdef CONFIG_ETRAX_I2C_DYN_ALLOC - dev_t devt; - struct cdev *my_i2cdev = NULL; -#endif - - res = i2c_init(); - - if ( res < 0 ) - { - return res; - } - -#ifdef CONFIG_ETRAX_I2C_DYN_ALLOC - res = alloc_chrdev_region( &devt, 0, 1, i2c_name ); - - if ( res < 0 ) - { - printk( KERN_DEBUG "I2C: EI2CNOMNUMBR\n" ); - return ( res ); - } - - my_i2cdev = cdev_alloc(); - my_i2cdev->ops = &i2c_fops; - my_i2cdev->owner = THIS_MODULE; - - /* make device "alive" */ - res = cdev_add( my_i2cdev, devt, 1 ); - - if ( res < 0 ) - { - printk( KERN_DEBUG "I2C: EI2CDADDFAIL\n" ); - return ( res ); - } - - int i2c_major = MAJOR( devt ); -#else - res = register_chrdev( I2C_MAJOR, i2c_name, &i2c_fops ); - - if ( res < 0 ) - { - printk( KERN_ERR "i2c: couldn't get a major number.\n" ); - return res; - } - - int i2c_major = I2C_MAJOR; -#endif - - printk( KERN_INFO "I2C: driver v2.3, (c) 1999-2004 Axis Communications AB\n" ); - printk( KERN_INFO "I2C: Improvements by Geert Vancompernolle, Positive Going, BK srl\n" ); - -#ifdef CONFIG_ETRAX_I2C_SLAVE_DELAY - printk( KERN_INFO "I2C: with master/slave delay patch\n" ); -#endif - - i2c_class = class_create (THIS_MODULE, "i2c_etrax"); - device_create (i2c_class, NULL, - MKDEV(i2c_major,0), NULL, i2c_name); - - return ( 0 ); -} /* i2c_register */ - - -/*#--------------------------------------------------------------------------- - *# - *# FUNCTION NAME: i2c_start - *# - *# DESCRIPTION : generate i2c start condition - *# - *# PARAMETERS : none - *# - *# RETURN : EI2CNOERRORS if OK, EI2CSTRTCOND otherwise - *# - *#--------------------------------------------------------------------------- - */ -int i2c_start( void ) -{ - /* Set SCL=1, SDA=1 */ - i2c_sda_dir_out(); - i2c_set_sda( SDA_HIGH ); - i2c_delay( WAITONEUS ); - i2c_set_scl( SCL_HIGH ); - i2c_delay( WAITONEUS ); - - /* Set SCL=1, SDA=0 */ - i2c_set_sda( SDA_LOW ); - i2c_delay( THDSTA ); - - /* Set SCL=0, SDA=0 */ - i2c_set_scl( SCL_LOW ); - /* We can take 1 us less than defined in spec (5 us), since the next action - * will be to set the dataline high or low and this action is 1 us - * before the clock is put high, so that makes our 5 us. - */ - i2c_delay( TLOW - WAITONEUS ); - - if ( i2c_sda_is_high() || i2c_scl_is_high() ) - { - printk( KERN_DEBUG "I2C: EI2CSTRTCOND\n" ); - return ( EI2CSTRTCOND ); - } - - return ( EI2CNOERRORS ); -} /* i2c_start */ - - -/*#--------------------------------------------------------------------------- - *# - *# FUNCTION NAME: i2c_stop - *# - *# DESCRIPTION : generate i2c stop condition - *# - *# PARAMETERS : none - *# - *# RETURN : none - *# - *#--------------------------------------------------------------------------- - */ -int i2c_stop( void ) -{ -#ifdef CONFIG_ETRAX_I2C_SLAVE_DELAY - int n=MAXSCLRETRIES; -#endif - i2c_sda_dir_out(); - - /* Set SCL=0, SDA=0 */ - /* Don't change order, otherwise you might generate a start condition! */ - i2c_set_scl( SCL_LOW ); - i2c_delay( WAITONEUS ); - i2c_set_sda( SDA_LOW ); - i2c_delay( WAITONEUS ); - - /* Set SCL=1, SDA=0 */ - -#ifdef CONFIG_ETRAX_I2C_SLAVE_DELAY - i2c_set_scl( SCL_HIGH ); - i2c_scl_dir_in(); - for( ; n>0; n-- ) - { - if( i2c_scl_is_high() ) - break; - i2c_delay( TSUSTO ); - } - - i2c_scl_dir_out(); -#else - i2c_set_scl( SCL_HIGH ); -#endif - i2c_delay( TSUSTO ); - - /* Set SCL=1, SDA=1 */ - i2c_set_sda( SDA_HIGH ); - i2c_delay( TBUF ); - - i2c_sda_dir_in(); - - if ( !i2c_sda_is_high() || !i2c_scl_is_high() ) - { - return ( EI2CSTOPCOND ); - } - - return ( EI2CNOERRORS ); -} /* i2c_stop */ - - -/*#--------------------------------------------------------------------------- - *# - *# FUNCTION NAME: i2c_outbyte - *# - *# DESCRIPTION : write a byte to the i2c interface - *# - *# PARAMETERS : x: byte to be sent on the I2C bus - *# - *# RETURN : none - *# - *#--------------------------------------------------------------------------- - */ -int i2c_outbyte( unsigned char x ) -{ - int i; - - i2c_sda_dir_out(); - - for ( i = 0; i < 8; i++ ) - { - if ( x & 0x80 ) - { - i2c_set_sda( SDA_HIGH ); - } - else - { - i2c_set_sda( SDA_LOW ); - } - - i2c_delay( TSUDAT ); - i2c_set_scl( SCL_HIGH ); - i2c_delay( THIGH ); - i2c_set_scl( SCL_LOW ); - i2c_delay( TSUDAT ); - i2c_set_sda( SDA_LOW ); - /* There should be only 5 us between falling edge and new rising - * edge of clock pulse. - * Since we spend already 1 us since clock edge was low, there are - * only ( TLOW - TSUDAT ) us left. - * Next to this, since the data line will be set up 1 us before the - * clock line is set up, we can reduce the delay with another us. - */ - i2c_delay( TLOW - TSUDAT - WAITONEUS ); - x <<= 1; - } - - /* enable input */ - i2c_sda_dir_in(); - - if ( !i2c_getack() ) - { - return( EI2CNOACKNLD ); - } - - return ( EI2CNOERRORS ); -} /* i2c_outbyte */ - - -/*#--------------------------------------------------------------------------- - *# - *# FUNCTION NAME: i2c_inbyte - *# - *# DESCRIPTION : read a byte from the i2c interface - *# - *# PARAMETERS : none - *# - *# RETURN : returns the byte read from the I2C device - *# - *#--------------------------------------------------------------------------- - */ -unsigned char i2c_inbyte( void ) -{ -#ifdef CONFIG_ETRAX_I2C_SLAVE_DELAY - int n=MAXSCLRETRIES; -#endif - unsigned char aBitByte = 0; - unsigned char Mask = 0x80; /* !!! ATTENTION: do NOT use 'char', otherwise shifting is wrong!!! */ - /* Must be UNSIGNED, not SIGNED! */ - - - /* Switch off I2C to get bit */ - i2c_disable(); - i2c_sda_dir_in(); - - while ( Mask != 0 ) - { -#ifdef CONFIG_ETRAX_I2C_SLAVE_DELAY - i2c_scl_dir_in(); - for( ; n>0; n-- ) - { - if( i2c_scl_is_high() ) - break; - i2c_delay( THIGH ); - } - - i2c_set_scl( SCL_HIGH ); - i2c_scl_dir_out(); -#else - i2c_set_scl( SCL_HIGH ); -#endif - i2c_delay( THIGH ); - - if ( i2c_sda_is_high() ) - { - aBitByte |= Mask; - } - - i2c_set_scl( SCL_LOW ); - - Mask >>= 1; - - i2c_delay( TLOW ); - } - - /* - * we leave the clock low, getbyte is usually followed - * by sendack/nack, they assume the clock to be low - */ - return ( aBitByte ); -} /* i2c_inbyte */ - - -/*#--------------------------------------------------------------------------- - *# - *# FUNCTION NAME: i2c_getack - *# - *# DESCRIPTION : checks if ack was received from ic2 - *# - *# PARAMETERS : none - *# - *# RETURN : returns the ack state of the I2C device - *# - *#--------------------------------------------------------------------------- - */ -int i2c_getack( void ) -{ - int ack = 1; -#ifdef CONFIG_ETRAX_I2C_SLAVE_DELAY - int n=MAXSCLRETRIES; -#endif - - /* generate ACK clock pulse */ - i2c_set_scl( SCL_HIGH ); - - /* switch off I2C */ - i2c_disable(); - -#ifdef CONFIG_ETRAX_I2C_SLAVE_DELAY - /* set clock low */ - i2c_set_scl( SCL_LOW ); - - /* now wait for ack */ - i2c_delay( THIGH ); - - /* set clock as input */ - i2c_scl_dir_in(); - - /* wait for clock to rise (n=MAXSCLRETRIES) */ - for( ; n>0; n-- ) - { - if( i2c_scl_is_high() ) - break; - i2c_delay( THIGH ); - } - - i2c_set_scl( SCL_HIGH ); - - i2c_scl_dir_out(); - - i2c_delay( THIGH ); -#else - /* now wait for ack */ - i2c_delay( THIGH ); -#endif - - /* check for ack: if SDA is high, then NACK, else ACK */ - if ( i2c_sda_is_high() ) - { - ack = 0; - } - else - { - ack = 1; - } - - /* end clock pulse */ - i2c_enable(); - i2c_set_scl( SCL_LOW ); - i2c_sda_dir_out(); - i2c_set_sda( SDA_LOW ); - - /* Since we "lost" already THDDAT time, we can subtract it here... */ - i2c_delay( TLOW - THDDAT ); - - return ( ack ); -} /* i2c_getack */ - - -/*#--------------------------------------------------------------------------- - *# - *# FUNCTION NAME: i2c_sendack - *# - *# DESCRIPTION : sends ACK on received data - *# - *# PARAMETERS : none - *# - *# RETURN : none - *# - *#--------------------------------------------------------------------------- - */ -void i2c_sendack( void ) -{ -#ifdef CONFIG_ETRAX_I2C_SLAVE_DELAY - int n=MAXSCLRETRIES; -#endif - - /* enable output */ - /* Clock has been set to TLOW already at end of i2c_inbyte() - * and i2c_outbyte(), so no need to do it again. - */ - i2c_sda_dir_out(); - /* set ack pulse low */ - i2c_set_sda( SDA_LOW ); - /* generate clock pulse */ - i2c_delay( TSUDAT ); - -#ifdef CONFIG_ETRAX_I2C_SLAVE_DELAY - i2c_scl_dir_in(); - /* wait for clock to rise (n=MAXSCLRETRIES) */ - for( ; n>0; n-- ) - { - if( i2c_scl_is_high() ) - break; - i2c_delay( THIGH ); - } - - i2c_set_scl( SCL_HIGH ); - i2c_scl_dir_out(); - i2c_delay( THIGH ); -#else - i2c_set_scl( SCL_HIGH ); - - i2c_delay( THIGH ); -#endif - i2c_set_scl( SCL_LOW ); - i2c_delay( THDDAT ); - /* reset data out */ - i2c_set_sda( SDA_HIGH ); - /* Subtract time spend already when waited to put SDA high */ - i2c_delay( TLOW - THDDAT ); - - /* release the SDA line */ - i2c_sda_dir_in(); -} /* i2c_sendack */ - - -/*#--------------------------------------------------------------------------- - *# - *# FUNCTION NAME: i2c_sendnack - *# - *# DESCRIPTION : sends NACK on received data - *# - *# PARAMETERS : none - *# - *# RETURN : none - *# - *#--------------------------------------------------------------------------- - */ -void i2c_sendnack( void ) -{ -#ifdef CONFIG_ETRAX_I2C_SLAVE_DELAY - int n=MAXSCLRETRIES; -#endif - - /* make sure the SDA line is set high prior to activation of the output. - * this way, you avoid an unnecessary peak to ground when a NACK has to - * be created. - */ - /* set data high */ - i2c_set_sda( SDA_HIGH ); - /* enable output */ - i2c_sda_dir_out(); - - /* generate clock pulse */ - i2c_delay( TSUDAT ); - -#ifdef CONFIG_ETRAX_I2C_SLAVE_DELAY - i2c_scl_dir_in(); - /* wait for clock to rise (n=MAXSCLRETRIES) */ - for( ; n>0; n-- ) - { - if( i2c_scl_is_high() ) - break; - i2c_delay( THIGH ); - } - - i2c_set_scl( SCL_HIGH ); - i2c_scl_dir_out(); - i2c_delay( THIGH ); -#else - i2c_set_scl( SCL_HIGH ); - - i2c_delay( THIGH ); -#endif - i2c_set_scl( SCL_LOW ); - i2c_delay( TSUDAT ); - i2c_set_sda( SDA_LOW ); - i2c_delay( TLOW - TSUDAT ); - - /* There's no need to change the direction of SDA to "in" again, - * since a NACK is always followed by a stop condition. - * A STOP condition will put the direction of SDA back to "out" - * resulting in a useless SDA "dip" on the line... - */ - /* i2c_sda_dir_in(); */ -} /* i2c_sendnack */ - - -/*#--------------------------------------------------------------------------- - *# - *# FUNCTION NAME: i2c_writereg - *# - *# DESCRIPTION : writes a value to a register of an I2C device - *# - *# PARAMETERS : theSlave = slave address of the I2C device - *# theReg = register of the I2C device that needs to be written - *# theValue = value to be written to the register - *# - *# RETURN : returns OR-ed result of the write action: - *# 0 = Ok - *# 1 = Slave_NoAck - *# 2 = Reg_NoAck - *# 4 = Val_NoAck - *# - *#--------------------------------------------------------------------------- - */ -int i2c_writereg( unsigned char theSlave - , unsigned char theReg - , unsigned char theValue - ) -{ - int error, cntr = 3; - unsigned long flags; - - spin_lock( &i2c_lock ); - - do - { - error = 0; - /* we don't like to be interrupted */ - local_irq_save( flags ); - - i2c_start(); - /* send slave address */ - if ( EI2CNOACKNLD == i2c_outbyte( theSlave & 0xfe ) ) - { - error = 1; - } - - /* now select register */ - if ( EI2CNOACKNLD == i2c_outbyte( theReg ) ) - { - error |= 2; - } - - /* send register register data */ - if ( EI2CNOACKNLD == i2c_outbyte( theValue ) ) - { - error |= 4; - } - - /* end byte stream */ - i2c_stop(); - /* enable interrupt again */ - local_irq_restore( flags ); - - } while ( error && cntr-- ); - - i2c_delay( TLOW ); - - spin_unlock( &i2c_lock ); - - return ( -error ); -} /* i2c_writereg */ - - -/*#--------------------------------------------------------------------------- - *# - *# FUNCTION NAME: i2c_readreg - *# - *# DESCRIPTION : reads the value from a certain register of an I2C device. - *# Function first writes the register that it wants to read - *# later on. - *# - *# PARAMETERS : theSlave = slave address of the I2C device - *# theReg = register of the I2C device that needs to be written - *# - *# RETURN : returns OR-ed result of the write action: - *# 0 = Ok - *# 1 = Slave_NoAck - *# 2 = Reg_NoAck - *# 4 = Val_NoAck - *# - *#--------------------------------------------------------------------------- - */ -unsigned char i2c_readreg( unsigned char theSlave - , unsigned char theReg - ) -{ - unsigned char b = 0; - int error, cntr = 3; - unsigned long flags; - - spin_lock( &i2c_lock ); - - do - { - error = 0; - - /* we don't like to be interrupted */ - local_irq_save( flags ); - - /* generate start condition */ - i2c_start(); - - /* send slave address */ - if ( EI2CNOACKNLD == i2c_outbyte( theSlave & 0xfe ) ) - { - error = 1; - } - - /* now select register */ - i2c_sda_dir_out(); - - if ( EI2CNOACKNLD == i2c_outbyte( theReg ) ) - { - error |= 2; - } - - /* repeat start condition */ - i2c_delay( TLOW ); - i2c_start(); - - /* send slave address */ - if ( EI2CNOACKNLD == i2c_outbyte( theSlave | 0x01 ) ) - { - error |= 1; - } - - /* fetch register */ - b = i2c_inbyte(); - /* - * last received byte needs to be nacked - * instead of acked - */ - i2c_sendnack(); - - /* end sequence */ - i2c_stop(); - - /* enable interrupt again */ - local_irq_restore( flags ); - - } while ( error && cntr-- ); - - spin_unlock( &i2c_lock ); - - return ( b ); -} /* i2c_readreg */ - - -/*#--------------------------------------------------------------------------- - *# - *# FUNCTION NAME: i2c_read - *# - *# DESCRIPTION : - *# - *# PARAMETERS : - *# - *# RETURN : - *# - *#--------------------------------------------------------------------------- - */ -int i2c_read( unsigned char slave, unsigned char* rbuf, unsigned char rlen ) -{ - return ( i2c_command( slave, NULL, 0, rbuf, rlen ) ); -} /* i2c_read */ - - -/*#--------------------------------------------------------------------------- - *# - *# FUNCTION NAME: i2c_write - *# - *# DESCRIPTION : - *# - *# PARAMETERS : - *# - *# RETURN : - *# - *#--------------------------------------------------------------------------- - */ -int i2c_write( unsigned char slave, unsigned char* wbuf, unsigned char wlen ) -{ - return ( i2c_command( slave, wbuf, wlen, NULL, 0 ) ); -} /* i2c_write */ - - -/*#--------------------------------------------------------------------------- - *# - *# FUNCTION NAME: i2c_writeread - *# - *# DESCRIPTION : - *# - *# PARAMETERS : - *# - *# RETURN : - *# - *#--------------------------------------------------------------------------- - */ -int i2c_writeread( unsigned char slave - , unsigned char* wbuf - , unsigned char wlen - , unsigned char* rbuf - , unsigned char rlen - ) -{ - return ( i2c_command( slave, wbuf, wlen, rbuf, rlen ) ); -} /* i2c_writeread */ - - -/*#--------------------------------------------------------------------------- - *# - *# FUNCTION NAME: module_init - *# - *# DESCRIPTION : this makes sure that i2c_register is called during boot - *# - *# PARAMETERS : - *# - *#--------------------------------------------------------------------------- - */ -module_init( i2c_register ); - -/****************** END OF FILE i2c.c ********************************/ diff --git a/target/linux/etrax/files/arch/cris/arch-v10/drivers/i2c_gvc.h b/target/linux/etrax/files/arch/cris/arch-v10/drivers/i2c_gvc.h deleted file mode 100644 index cac2d4689..000000000 --- a/target/linux/etrax/files/arch/cris/arch-v10/drivers/i2c_gvc.h +++ /dev/null @@ -1,30 +0,0 @@ -#ifndef _I2C_H -#define _I2C_H - -int i2c_init(void); - -/* High level I2C actions */ -int i2c_writereg(unsigned char theSlave, unsigned char theReg, unsigned char theValue); -unsigned char i2c_readreg(unsigned char theSlave, unsigned char theReg); - -/* Low level I2C */ -int i2c_start(void); -int i2c_stop(void); -int i2c_outbyte(unsigned char x); -unsigned char i2c_inbyte(void); -int i2c_getack(void); -void i2c_sendack(void); -void i2c_sendnack(void); - -/**GVC**/ -/* New low level I2C functions */ -int i2c_read( unsigned char slave, unsigned char* rbuf, unsigned char rlen ); -int i2c_write( unsigned char slave, unsigned char* wbuf, unsigned char wlen ); -int i2c_writeread( unsigned char slave - , unsigned char* wbuf - , unsigned char wlen - , unsigned char* rbuf - , unsigned char rlen - ); -/**END GVC**/ -#endif /* _I2C_H */ |