diff options
Diffstat (limited to 'package/network/config/ltq-dsl-app/files/dsl_control')
| -rw-r--r-- | package/network/config/ltq-dsl-app/files/dsl_control | 315 |
1 files changed, 0 insertions, 315 deletions
diff --git a/package/network/config/ltq-dsl-app/files/dsl_control b/package/network/config/ltq-dsl-app/files/dsl_control deleted file mode 100644 index 79961aaed..000000000 --- a/package/network/config/ltq-dsl-app/files/dsl_control +++ /dev/null @@ -1,315 +0,0 @@ -#!/bin/sh /etc/rc.common -# Copyright (C) 2012 OpenWrt.org - -START=99 - -EXTRA_COMMANDS="status lucistat" -EXTRA_HELP=" status Get DSL status information - lucistat Get status information if lua friendly format" - -SERVICE_DAEMONIZE=1 -SERVICE_WRITE_PID=1 - -# -# Basic functions to send CLI commands to the dsl_cpe_control daemon -# -dsl_cmd() { - killall -0 dsl_cpe_control && ( - echo "$@" > /tmp/pipe/dsl_cpe0_cmd - cat /tmp/pipe/dsl_cpe0_ack - ) -} -dsl_val() { - echo $(expr "$1" : '.*'$2'=\([-\.[:alnum:]]*\).*') -} - -# -# Simple divide by 10 routine to cope with one decimal place -# -dbt() { - local a=$(expr $1 / 10) - local b=$(expr $1 % 10) - echo "${a}.${b}" -} -# -# Take a number and convert to k or meg -# -scale() { - local val=$1 - local a - local b - - if [ "$val" -gt 1000000 ]; then - a=$(expr $val / 1000) - b=$(expr $a % 1000) - a=$(expr $a / 1000) - printf "%d.%03d Mb" ${a} ${b} - elif [ "$val" -gt 1000 ]; then - a=$(expr $val / 1000) - printf "%d Kb" ${a} - else - echo "${val} b" - fi -} - -# -# Read the data rates for both directions -# -data_rates() { - local csg - local dru - local drd - local sdru - local sdrd - - csg=$(dsl_cmd g997csg 0 1) - drd=$(dsl_val "$csg" ActualDataRate) - - csg=$(dsl_cmd g997csg 0 0) - dru=$(dsl_val "$csg" ActualDataRate) - - [ -z "$drd" ] && drd=0 - [ -z "$dru" ] && dru=0 - - sdrd=$(scale $drd) - sdru=$(scale $dru) - - if [ "$action" = "lucistat" ]; then - echo "dsl.data_rate_down=$drd" - echo "dsl.data_rate_up=$dru" - echo "dsl.data_rate_down_s=\"$sdrd\"" - echo "dsl.data_rate_up_s=\"$sdru\"" - else - echo "Data Rate: ${sdrd}/s / ${sdru}/s" - fi -} - -# -# Chipset -# -chipset() { - local vig - local cs - local csv - - vig=$(dsl_cmd vig) - cs=$(dsl_val "$vig" DSL_ChipSetType) - csv=$(dsl_val "$vig" DSL_ChipSetHWVersion) - - if [ "$action" = "lucistat" ]; then - echo "dsl.chipset=\"${cs} ${csv}\"" - else - echo "Chipset: ${cs} ${csv}" - fi -} - -# -# Work out how long the line has been up -# -line_uptime() { - local ccsg - local et - local etr - local d - local h - local m - local s - local rc="" - - ccsg=$(dsl_cmd pmccsg 0 0 0) - et=$(dsl_val "$ccsg" nElapsedTime) - - [ -z "$et" ] && et=0 - - if [ "$action" = "lucistat" ]; then - echo "dsl.line_uptime=${et}" - return - fi - - d=$(expr $et / 86400) - etr=$(expr $et % 86400) - h=$(expr $etr / 3600) - etr=$(expr $etr % 3600) - m=$(expr $etr / 60) - s=$(expr $etr % 60) - - - [ "${d}${h}${m}${s}" -ne 0 ] && rc="${s}s" - [ "${d}${h}${m}" -ne 0 ] && rc="${m}m ${rc}" - [ "${d}${h}" -ne 0 ] && rc="${h}h ${rc}" - [ "${d}" -ne 0 ] && rc="${d}d ${rc}" - - [ -z "$rc" ] && rc="down" - echo "Line Uptime: ${rc}" -} - -# -# Get noise and attenuation figures -# -line_data() { - local lsg - local latnu - local latnd - local snru - local snrd - - lsg=$(dsl_cmd g997lsg 1 1) - latnd=$(dsl_val "$lsg" LATN) - snrd=$(dsl_val "$lsg" SNR) - - lsg=$(dsl_cmd g997lsg 0 1) - latnu=$(dsl_val "$lsg" LATN) - snru=$(dsl_val "$lsg" SNR) - - [ -z "$latnd" ] && latnd=0 - [ -z "$latnu" ] && latnu=0 - [ -z "$snrd" ] && snrd=0 - [ -z "$snru" ] && snru=0 - - latnd=$(dbt $latnd) - latnu=$(dbt $latnu) - snrd=$(dbt $snrd) - snru=$(dbt $snru) - - if [ "$action" = "lucistat" ]; then - echo "dsl.line_attenuation_down=$latnd" - echo "dsl.line_attenuation_up=$latnu" - echo "dsl.noise_margin_down=$snrd" - echo "dsl.noise_margin_up=$snru" - else - echo "Line Attenuation: ${latnd}dB / ${latnu}dB" - echo "Noise Margin: ${snrd}dB / ${snru}dB" - fi -} - -# -# Is the line up? Or what state is it in? -# -line_state() { - local lsg=$(dsl_cmd lsg) - local ls=$(dsl_val "$lsg" nLineState); - local s; - - case "$ls" in - "0x0") s="not initialized" ;; - "0x1") s="exception" ;; - "0x10") s="not updated" ;; - "0xff") s="idle request" ;; - "0x100") s="idle" ;; - "0x1ff") s="silent request" ;; - "0x200") s="silent" ;; - "0x300") s="handshake" ;; - "0x380") s="full_init" ;; - "0x400") s="discovery" ;; - "0x500") s="training" ;; - "0x600") s="analysis" ;; - "0x700") s="exchange" ;; - "0x800") s="showtime_no_sync" ;; - "0x801") s="showtime_tc_sync" ;; - "0x900") s="fastretrain" ;; - "0xa00") s="lowpower_l2" ;; - "0xb00") s="loopdiagnostic active" ;; - "0xb10") s="loopdiagnostic data exchange" ;; - "0xb20") s="loopdiagnostic data request" ;; - "0xc00") s="loopdiagnostic complete" ;; - "0x1000000") s="test" ;; - "0xd00") s="resync" ;; - "0x3c0") s="short init entry" ;; - "") s="not running daemon"; ls="0xfff" ;; - *) s="unknown" ;; - esac - - if [ $action = "lucistat" ]; then - echo "dsl.line_state_num=$ls" - echo "dsl.line_state_detail=\"$s\"" - if [ "$ls" = "0x801" ]; then - echo "dsl.line_state=\"UP\"" - else - echo "dsl.line_state=\"DOWN\"" - fi - else - if [ "$ls" = "0x801" ]; then - echo "Line State: UP [$ls: $s]" - else - echo "Line State: DOWN [$ls: $s]" - fi - fi -} - -# -# Main status routine -# -status() { - chipset - line_state - data_rates - line_data - line_uptime -} - -# -# Luci (lua) compatible version that's easy to parse -# -lucistat() { - echo "local dsl={}" - status - echo "return dsl" -} - - -annex_b=10_00_10_00_00_04_00_00 -annex_bdmt=10_00_00_00_00_00_00_00 -annex_b2=00_00_10_00_00_00_00_00 -annex_b2p=00_00_00_00_00_04_00_00 -annex_a=04_01_04_00_00_01_00_00 -annex_at1=01_00_00_00_00_00_00_00 -annex_alite=00_01_00_00_00_00_00_00 -annex_admt=04_00_00_00_00_00_00_00 -annex_a2=00_00_04_00_00_00_00_00 -annex_a2p=00_00_00_00_00_01_00_00 -annex_l=00_00_00_00_04_00_00_00 -annex_m=00_00_00_00_40_00_04_00 -annex_m2=00_00_00_00_40_00_00_00 -annex_m2p=00_00_00_00_00_00_04_00 - -# -# Simple start routine -# -start() { - local annex - local fwannex - local xtu - config_load network - config_get annex adsl annex - config_get fwannex adsl fwannex - - # get xtu - eval "xtu=\"\${annex_$annex}\"" - - # check for invalid annex mode - [ -n "${annex}" -a -z "${xtu}" ] && - echo "unknown annex mode $annex" - - # check for invalid fw annex mode - [[ "$fwannex" != "a" && "$fwannex" != "b" ]] && - echo "invalid fwannex: $fwannex" - - # start CPE dsl daemon in the background - service_start /sbin/dsl_cpe_control -i${xtu} \ - -n /sbin/dsl_notify.sh \ - -f /lib/firmware/dsl-fw-${fwannex}.bin -} - -# -# For stop we want to simulate the notification call for when -# the line goes down, so that we can stop the ppp link before -# we die. -# -stop() { - DSL_NOTIFICATION_TYPE="DSL_INTERFACE_STATUS" \ - DSL_INTERFACE_STATUS="DOWN" \ - /sbin/dsl_notify.sh - - service_stop /sbin/dsl_cpe_control -} - |