bcm63xx: drop linux 3.2 support

git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31464 3c298f89-4303-0410-b956-a3cf2f4a3e73

1 files changed, 0 insertions, 111 deletions

diff --git a/target/linux/brcm63xx/patches-3.2/452-board_V2500V.patch b/target/linux/brcm63xx/patches-3.2/452-board_V2500V.patch
deleted file mode 100644
index d37ee450d..000000000
--- a/target/linux/brcm63xx/patches-3.2/452-board_V2500V.patch
+++ /dev/null
@@ -1,111 +0,0 @@
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -851,6 +851,63 @@ static struct board_info __initdata boar
- 	},
- };
- 
-+	static struct board_info __initdata board_V2500V_BB = {
-+        .name                           = "V2500V_BB",
-+        .expected_cpu_id                = 0x6348,
-+
-+        .has_uart0                      = 1,
-+        .has_enet0                      = 1,
-+        .has_enet1                      = 1,
-+        .has_pci                        = 1,
-+
-+        .enet0 = {
-+                .has_phy                = 1,
-+                .use_internal_phy       = 1,
-+        },
-+        .enet1 = {
-+                .force_speed_100        = 1,
-+                .force_duplex_full      = 1,
-+        },
-+
-+	.leds = {
-+		{
-+			.name		= "power:green",
-+			.gpio		= 0,
-+			.active_low	= 1,
-+			.default_trigger = "default-on",
-+		},
-+		{
-+			.name		= "power:red",
-+			.gpio		= 1,
-+			.active_low	= 1,
-+		},
-+		{
-+			.name		= "adsl",
-+			.gpio		= 2,
-+			.active_low	= 1,
-+		},
-+		{	.name		= "ppp",
-+			.gpio		= 3,
-+			.active_low	= 1,
-+		},
-+		{
-+			.name		= "wireless",
-+			.gpio		= 6,
-+			.active_low	= 1,
-+		},
-+	},
-+	.buttons = {
-+		{
-+			.desc		= "reset",
-+			.gpio		= 31,
-+			.active_low	= 1,
-+			.type		= EV_KEY,
-+			.code		= KEY_RESTART,
-+			.threshold	= 3,
-+		},
-+	},
-+};
-+
- #endif
- 
- /*
-@@ -1898,6 +1955,7 @@ static const struct board_info __initdat
- 	&board_96348_D4PW,
- 	&board_spw500v,
- 	&board_96348sv,
-+	&board_V2500V_BB,
- #endif
- 
- #ifdef CONFIG_BCM63XX_CPU_6358
-@@ -2051,6 +2109,22 @@ void __init board_prom_init(void)
- 	val = bcm_mpi_readl(MPI_CSBASE_REG(0));
- 	val &= MPI_CSBASE_BASE_MASK;
- 	boot_addr = (u8 *)KSEG1ADDR(val);
-+	printk(KERN_INFO PFX "Boot address 0x%08x\n",(unsigned int)boot_addr);
-+
-+	/* BT Voyager 2500V (RTA1046VW PCB) has 8 Meg flash used as two */
-+	/* banks of 4 Meg. The byte at 0xBF800000 identifies the back to use.*/
-+	/* Loading firmware from the CFE Prompt always loads to Bank 0 */
-+	/* Do an early check of CFE and then select bank 0 */
-+
-+       	if (boot_addr == (u8 *)0xbf800000) {
-+		u8 *tmp_boot_addr;
-+		tmp_boot_addr = (u8 *)0xbfc00000; // Address of Bank 0
-+		memcpy(&nvram, tmp_boot_addr + BCM963XX_NVRAM_OFFSET, sizeof(nvram));
-+		if (!strcmp(nvram.name, "V2500V_BB")) {
-+	               	printk(KERN_INFO PFX "V2500V: nvram bank 0\n");
-+			boot_addr = (u8 *)0xbfc00000; // Bank 0
-+		}
-+	}
- 
- 	/* dump cfe version */
- 	cfe = boot_addr + BCM963XX_CFE_VERSION_OFFSET;
-@@ -2249,6 +2323,13 @@ int __init board_register_devices(void)
- 	val = bcm_mpi_readl(MPI_CSBASE_REG(0));
- 	val &= MPI_CSBASE_BASE_MASK;
- 
-+	/* BT Voyager 2500V has 8 Meg flash in two 4 Meg banks */
-+	/* Loading from CFE always uses Bank 0 */
-+	if (!strcmp(board.name, "V2500V_BB")) {
-+		printk(KERN_INFO PFX "V2500V: Start in Bank 0\n");
-+		val = val + 0x400000; // Select Bank 0 start address
-+	}
-+
- 	mtd_resources[0].start = val;
- 	mtd_resources[0].end = 0x1FFFFFFF;
-