strip the kernel version suffix from target directories, except for brcm-2.4 (the -2.4 will be included in the board name here). CONFIG_LINUX_<ver>_<board> becomes CONFIG_TARGET_<board>, same for profiles.

git-svn-id: svn://svn.openwrt.org/openwrt/trunk@8653 3c298f89-4303-0410-b956-a3cf2f4a3e73

1 files changed, 520 insertions, 0 deletions

diff --git a/target/linux/adm5120/files/drivers/serial/adm5120_uart.c b/target/linux/adm5120/files/drivers/serial/adm5120_uart.c
new file mode 100644
index 000000000..83c5f7201
--- /dev/null
+++ b/target/linux/adm5120/files/drivers/serial/adm5120_uart.c
@@ -0,0 +1,520 @@
+/*
+ *	Serial driver for ADM5120 SoC
+ *
+ *	Derived from drivers/serial/uart00.c
+ *	Copyright 2001 Altera Corporation
+ *
+ *	Some pieces are derived from the ADMtek 2.4 serial driver.
+ *	Copyright (C) ADMtek Incorporated, 2003
+ *		daniell@admtek.com.tw
+ *	Which again was derived from drivers/char/serial.c
+ *	Copyright (C) Linus Torvalds et al.
+ *
+ *	Copyright Jeroen Vreeken (pe1rxq@amsat.org), 2005
+ */
+
+#include <linux/autoconf.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/ioport.h>
+#include <linux/serial.h>
+#include <linux/serial_core.h>
+#include <linux/tty.h>
+#include <linux/tty_flip.h>
+#include <linux/console.h>
+
+#include <asm/mach-adm5120/adm5120_defs.h>
+#include <asm/mach-adm5120/adm5120_irq.h>
+
+#define ADM5120_UART_REG(base, reg) \
+	(*(volatile u32 *)KSEG1ADDR((base)+(reg)))
+
+#define ADM5120_UARTCLK_FREQ            62500000
+#define ADM5120_UART_BAUDDIV(rate)	((unsigned long)(ADM5120_UARTCLK_FREQ/(16*(rate)) - 1))
+
+#define ADM5120_UART_BAUD115200		ADM5120_UART_BAUDDIV(115200)
+
+#define ADM5120_UART_DATA		0x00
+#define ADM5120_UART_RS			0x04
+#define ADM5120_UART_LCR_H		0x08
+#define ADM5120_UART_LCR_M		0x0c
+#define ADM5120_UART_LCR_L		0x10
+#define ADM5120_UART_CR			0x14
+#define ADM5120_UART_FR			0x18
+#define ADM5120_UART_IR			0x1c
+
+#define ADM5120_UART_FE			0x01
+#define ADM5120_UART_PE			0x02
+#define ADM5120_UART_BE			0x04
+#define ADM5120_UART_OE			0x08
+#define ADM5120_UART_ERR		0x0f
+#define ADM5120_UART_FIFO_EN		0x10
+#define ADM5120_UART_EN			0x01
+#define ADM5120_UART_TIE		0x20
+#define ADM5120_UART_RIE		0x50
+#define ADM5120_UART_IE			0x78
+#define ADM5120_UART_CTS		0x01
+#define ADM5120_UART_DSR		0x02
+#define ADM5120_UART_DCD		0x04
+#define ADM5120_UART_TXFF		0x20
+#define ADM5120_UART_TXFE		0x80
+#define ADM5120_UART_RXFE		0x10
+#define ADM5120_UART_BRK		0x01
+#define ADM5120_UART_PEN		0x02
+#define ADM5120_UART_EPS		0x04
+#define ADM5120_UART_STP2		0x08
+#define ADM5120_UART_W5			0x00
+#define ADM5120_UART_W6			0x20
+#define ADM5120_UART_W7			0x40
+#define ADM5120_UART_W8			0x60
+#define ADM5120_UART_MIS		0x01
+#define ADM5120_UART_RIS		0x02
+#define ADM5120_UART_TIS		0x04
+#define ADM5120_UART_RTIS		0x08
+
+static void adm5120ser_stop_tx(struct uart_port *port)
+{
+	ADM5120_UART_REG(port->iobase, ADM5120_UART_CR) &= ~ADM5120_UART_TIE;
+}
+
+static void adm5120ser_irq_rx(struct uart_port *port)
+{
+	struct tty_struct *tty = port->info->tty;
+	unsigned int status, ch, rds, flg, ignored = 0;
+
+	status = ADM5120_UART_REG(port->iobase, ADM5120_UART_FR);
+	while (!(status & ADM5120_UART_RXFE)) {
+		/* 
+		 * We need to read rds before reading the 
+		 * character from the fifo
+		 */
+		rds = ADM5120_UART_REG(port->iobase, ADM5120_UART_RS);
+		ch = ADM5120_UART_REG(port->iobase, ADM5120_UART_DATA);
+		port->icount.rx++;
+
+		if (tty->low_latency)
+			tty_flip_buffer_push(tty);
+
+		flg = TTY_NORMAL;
+
+		/*
+		 * Note that the error handling code is
+		 * out of the main execution path
+		 */
+		if (rds & ADM5120_UART_ERR)
+			goto handle_error;
+		if (uart_handle_sysrq_char(port, ch))
+			goto ignore_char;
+
+	error_return:
+		tty_insert_flip_char(tty, ch, flg);
+
+	ignore_char:
+		status = ADM5120_UART_REG(port->iobase, ADM5120_UART_FR);
+	}
+ out:
+	tty_flip_buffer_push(tty);
+	return;
+
+ handle_error:
+ 	ADM5120_UART_REG(port->iobase, ADM5120_UART_RS) = 0xff;
+	if (rds & ADM5120_UART_BE) {
+		port->icount.brk++;
+		if (uart_handle_break(port))
+			goto ignore_char;
+	} else if (rds & ADM5120_UART_PE)
+		port->icount.parity++;
+	else if (rds & ADM5120_UART_FE)
+		port->icount.frame++;
+	if (rds & ADM5120_UART_OE)
+		port->icount.overrun++;
+
+	if (rds & port->ignore_status_mask) {
+		if (++ignored > 100)
+			goto out;
+		goto ignore_char;
+	}
+	rds &= port->read_status_mask;
+
+	if (rds & ADM5120_UART_BE)
+		flg = TTY_BREAK;
+	else if (rds & ADM5120_UART_PE)
+		flg = TTY_PARITY;
+	else if (rds & ADM5120_UART_FE)
+		flg = TTY_FRAME;
+
+	if (rds & ADM5120_UART_OE) {
+		/*
+		 * CHECK: does overrun affect the current character?
+		 * ASSUMPTION: it does not.
+		 */
+		tty_insert_flip_char(tty, ch, flg);
+		ch = 0;
+		flg = TTY_OVERRUN;
+	}
+#ifdef CONFIG_MAGIC_SYSRQ
+	port->sysrq = 0;
+#endif
+	goto error_return;
+}
+
+static void adm5120ser_irq_tx(struct uart_port *port)
+{
+	struct circ_buf *xmit = &port->info->xmit;
+	int count;
+
+	if (port->x_char) {
+		ADM5120_UART_REG(port->iobase, ADM5120_UART_DATA) =
+		    port->x_char;
+		port->icount.tx++;
+		port->x_char = 0;
+		return;
+	}
+	if (uart_circ_empty(xmit) || uart_tx_stopped(port)) {
+		adm5120ser_stop_tx(port);
+		return;
+	}
+
+	count = port->fifosize >> 1;
+	do {
+		ADM5120_UART_REG(port->iobase, ADM5120_UART_DATA) =
+		    xmit->buf[xmit->tail];
+		xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
+		port->icount.tx++;
+		if (uart_circ_empty(xmit))
+			break;
+	} while (--count > 0);
+
+	if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
+		uart_write_wakeup(port);
+
+	if (uart_circ_empty(xmit))
+		adm5120ser_stop_tx(port);
+}
+
+static void adm5120ser_irq_modem(struct uart_port *port)
+{
+	unsigned int status;
+
+	status = ADM5120_UART_REG(port->iobase, ADM5120_UART_FR);
+
+	if (status & ADM5120_UART_DCD)
+		uart_handle_dcd_change(port, status & ADM5120_UART_DCD);
+
+	if (status & ADM5120_UART_DSR)
+		port->icount.dsr++;
+
+	if (status & ADM5120_UART_CTS)
+		uart_handle_cts_change(port, status & ADM5120_UART_CTS);
+
+	wake_up_interruptible(&port->info->delta_msr_wait);
+}
+
+static irqreturn_t adm5120ser_irq(int irq, void *dev_id)
+{
+	struct uart_port *port = dev_id;
+	unsigned long ir = ADM5120_UART_REG(port->iobase, ADM5120_UART_IR);
+
+	if (ir & (ADM5120_UART_RIS | ADM5120_UART_RTIS))
+		adm5120ser_irq_rx(port);
+	if (ir & ADM5120_UART_TIS)
+		adm5120ser_irq_tx(port);
+	if (ir & ADM5120_UART_MIS) {
+		adm5120ser_irq_modem(port);
+		ADM5120_UART_REG(port->iobase, ADM5120_UART_IR) = 0xff;
+	}
+
+	return IRQ_HANDLED;
+}
+
+static unsigned int adm5120ser_tx_empty(struct uart_port *port)
+{
+	unsigned int fr = ADM5120_UART_REG(port->iobase, ADM5120_UART_FR);
+	return (fr & ADM5120_UART_TXFE) ? TIOCSER_TEMT : 0;
+}
+
+static void adm5120ser_set_mctrl(struct uart_port *port, unsigned int mctrl)
+{
+}
+
+static unsigned int adm5120ser_get_mctrl(struct uart_port *port)
+{
+	unsigned int result = 0;
+	unsigned int fr = ADM5120_UART_REG(port->iobase, ADM5120_UART_FR);
+
+	if (fr & ADM5120_UART_CTS)
+		result |= TIOCM_CTS;
+	if (fr & ADM5120_UART_DSR)
+		result |= TIOCM_DSR;
+	if (fr & ADM5120_UART_DCD)
+		result |= TIOCM_CAR;
+	return result;
+}
+
+static void adm5120ser_start_tx(struct uart_port *port)
+{
+	ADM5120_UART_REG(port->iobase, ADM5120_UART_CR) |= ADM5120_UART_TIE;
+}
+
+static void adm5120ser_stop_rx(struct uart_port *port)
+{
+	ADM5120_UART_REG(port->iobase, ADM5120_UART_CR) &= ~ADM5120_UART_RIE;
+}
+
+static void adm5120ser_enable_ms(struct uart_port *port)
+{
+}
+
+static void adm5120ser_break_ctl(struct uart_port *port, int break_state)
+{
+	unsigned long flags;
+	unsigned long lcrh;
+
+	spin_lock_irqsave(&port->lock, flags);
+	lcrh = ADM5120_UART_REG(port->iobase, ADM5120_UART_LCR_H);
+	if (break_state == -1)
+		lcrh |= ADM5120_UART_BRK;
+	else
+		lcrh &= ~ADM5120_UART_BRK;
+	ADM5120_UART_REG(port->iobase, ADM5120_UART_LCR_H) = lcrh;
+	spin_unlock_irqrestore(&port->lock, flags);
+}
+
+static int adm5120ser_startup(struct uart_port *port)
+{
+	int ret;
+
+	ret = request_irq(port->irq, adm5120ser_irq, 0, "ADM5120 UART", port);
+	if (ret) {
+		printk(KERN_ERR "Couldn't get irq %d\n", port->irq);
+		return ret;
+	}
+	ADM5120_UART_REG(port->iobase, ADM5120_UART_LCR_H) |=
+	    ADM5120_UART_FIFO_EN;
+	ADM5120_UART_REG(port->iobase, ADM5120_UART_CR) |=
+	    ADM5120_UART_EN | ADM5120_UART_IE;
+	return 0;
+}
+
+static void adm5120ser_shutdown(struct uart_port *port)
+{
+	ADM5120_UART_REG(port->iobase, ADM5120_UART_CR) &= ~ADM5120_UART_IE;
+	free_irq(port->irq, port);
+}
+
+static void adm5120ser_set_termios(struct uart_port *port,
+    struct ktermios *termios, struct ktermios *old)
+{
+	unsigned int baud, quot, lcrh;
+	unsigned long flags;
+
+	termios->c_cflag |= CREAD;
+
+	baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk/16);
+	quot = uart_get_divisor(port, baud);
+
+	lcrh = ADM5120_UART_FIFO_EN;
+	switch (termios->c_cflag & CSIZE) {
+		case CS5:
+			lcrh |= ADM5120_UART_W5;
+			break;
+		case CS6:
+			lcrh |= ADM5120_UART_W6;
+			break;
+		case CS7:
+			lcrh |= ADM5120_UART_W7;
+			break;
+		default:
+			lcrh |= ADM5120_UART_W8;
+			break;
+	}
+	if (termios->c_cflag & CSTOPB)
+		lcrh |= ADM5120_UART_STP2;
+	if (termios->c_cflag & PARENB) {
+		lcrh |= ADM5120_UART_PEN;
+		if (!(termios->c_cflag & PARODD))
+			lcrh |= ADM5120_UART_EPS;
+	}
+
+	spin_lock_irqsave(port->lock, flags);
+
+	ADM5120_UART_REG(port->iobase, ADM5120_UART_LCR_H) = lcrh;
+
+	/*
+	 * Update the per-port timeout.
+	 */
+	uart_update_timeout(port, termios->c_cflag, baud);
+
+	port->read_status_mask = ADM5120_UART_OE;
+	if (termios->c_iflag & INPCK)
+		port->read_status_mask |= ADM5120_UART_FE | ADM5120_UART_PE;
+	if (termios->c_iflag & (BRKINT | PARMRK))
+		port->read_status_mask |= ADM5120_UART_BE;
+
+	/*
+	 * Characters to ignore
+	 */
+	port->ignore_status_mask = 0;
+	if (termios->c_iflag & IGNPAR)
+		port->ignore_status_mask |= ADM5120_UART_FE | ADM5120_UART_PE;
+	if (termios->c_iflag & IGNBRK) {
+		port->ignore_status_mask |= ADM5120_UART_BE;
+		/*
+		 * If we're ignoring parity and break indicators,
+		 * ignore overruns to (for real raw support).
+		 */
+		if (termios->c_iflag & IGNPAR)
+			port->ignore_status_mask |= ADM5120_UART_OE;
+	}
+
+	quot = ADM5120_UART_BAUD115200;
+	ADM5120_UART_REG(port->iobase, ADM5120_UART_LCR_L) = quot & 0xff;
+	ADM5120_UART_REG(port->iobase, ADM5120_UART_LCR_M) = quot >> 8;
+
+	spin_unlock_irqrestore(&port->lock, flags);
+}
+
+static const char *adm5120ser_type(struct uart_port *port)
+{
+	return port->type == PORT_ADM5120 ? "ADM5120" : NULL;
+}
+
+static void adm5120ser_config_port(struct uart_port *port, int flags)
+{
+	if (flags & UART_CONFIG_TYPE)
+		port->type = PORT_ADM5120;
+}
+
+static void adm5120ser_release_port(struct uart_port *port)
+{
+	release_mem_region(port->iobase, ADM5120_UART_SIZE);
+}
+
+static int adm5120ser_request_port(struct uart_port *port)
+{
+	return request_mem_region(port->iobase, ADM5120_UART_SIZE,
+	    "adm5120-uart") != NULL ? 0 : -EBUSY; 
+}
+
+static struct uart_ops adm5120ser_ops = {
+	.tx_empty =	adm5120ser_tx_empty,
+	.set_mctrl =	adm5120ser_set_mctrl,
+	.get_mctrl =	adm5120ser_get_mctrl,
+	.stop_tx =	adm5120ser_stop_tx,
+	.start_tx =	adm5120ser_start_tx,
+	.stop_rx =	adm5120ser_stop_rx,
+	.enable_ms =	adm5120ser_enable_ms,
+	.break_ctl =	adm5120ser_break_ctl,
+	.startup =	adm5120ser_startup,
+	.shutdown =	adm5120ser_shutdown,
+	.set_termios =	adm5120ser_set_termios,
+	.type =		adm5120ser_type,
+	.config_port =	adm5120ser_config_port,
+	.release_port =	adm5120ser_release_port,
+	.request_port =	adm5120ser_request_port,
+};
+
+static void adm5120console_put(const char c)
+{
+	while ((ADM5120_UART_REG(ADM5120_UART0_BASE, ADM5120_UART_FR) &
+	     ADM5120_UART_TXFF) != 0);
+	ADM5120_UART_REG(ADM5120_UART0_BASE, ADM5120_UART_DATA) = c;
+}
+
+static void adm5120console_write(struct console *con, const char *s,
+    unsigned int count)
+{
+	while (count--) {
+		if (*s == '\n')
+			adm5120console_put('\r');
+		adm5120console_put(*s);
+		s++;
+	}
+}
+
+static int adm5120console_setup(struct console *con, char *options)
+{
+	/* Set to 115200 baud, 8N1 and enable FIFO */
+	ADM5120_UART_REG(ADM5120_UART0_BASE, ADM5120_UART_LCR_L) =
+	    ADM5120_UART_BAUD115200 & 0xff;
+	ADM5120_UART_REG(ADM5120_UART0_BASE, ADM5120_UART_LCR_M) =
+	    ADM5120_UART_BAUD115200 >> 8;
+	ADM5120_UART_REG(ADM5120_UART0_BASE, ADM5120_UART_LCR_H) =
+	    ADM5120_UART_W8 | ADM5120_UART_FIFO_EN;
+	/* Enable port */
+	ADM5120_UART_REG(ADM5120_UART0_BASE, ADM5120_UART_CR) =
+	    ADM5120_UART_EN;
+
+	return 0;
+}
+
+static struct uart_driver adm5120ser_reg;
+
+static struct console adm5120_serconsole = {
+	.name =		"ttyS",
+	.write =	adm5120console_write,
+	.device =	uart_console_device,
+	.setup =	adm5120console_setup,
+	.flags =	CON_PRINTBUFFER,
+	.cflag =	B115200 | CS8 | CREAD,
+	.index =	0,
+	.data =		&adm5120ser_reg,
+};
+
+static int __init adm5120console_init(void)
+{
+	register_console(&adm5120_serconsole);
+	return 0;
+}
+
+console_initcall(adm5120console_init);
+
+
+static struct uart_port adm5120ser_ports[] = {
+	{
+		.iobase =	ADM5120_UART0_BASE,
+		.irq =		ADM5120_IRQ_UART0,
+		.uartclk =	ADM5120_UARTCLK_FREQ,
+		.fifosize =	16,
+		.ops =		&adm5120ser_ops,
+		.line =		0,
+		.flags =	ASYNC_BOOT_AUTOCONF,
+	},
+#if (CONFIG_ADM5120_NR_UARTS > 1)
+	{
+		.iobase =	ADM5120_UART1_BASE,
+		.irq =		ADM5120_IRQ_UART1,
+		.uartclk =	ADM5120_UARTCLK_FREQ,
+		.fifosize =	16,
+		.ops =		&adm5120ser_ops,
+		.line =		1,
+		.flags =	ASYNC_BOOT_AUTOCONF,
+	},
+#endif
+};
+
+static struct uart_driver adm5120ser_reg = {
+	.owner	=	THIS_MODULE,
+	.driver_name =	"ttyS",
+	.dev_name =	"ttyS",
+	.major =	TTY_MAJOR,
+	.minor =	64,
+	.nr =		CONFIG_ADM5120_NR_UARTS,
+	.cons =		&adm5120_serconsole,
+};
+
+static int __init adm5120ser_init(void)
+{
+	int ret, i;
+
+	ret = uart_register_driver(&adm5120ser_reg);
+	if (!ret) {
+		for (i = 0; i < CONFIG_ADM5120_NR_UARTS; i++)
+			uart_add_one_port(&adm5120ser_reg, &adm5120ser_ports[i]);
+	}
+
+	return ret;
+}
+
+__initcall(adm5120ser_init);