strip the kernel version suffix from target directories, except for brcm-2.4 (the -2.4 will be included in the board name here). CONFIG_LINUX_<ver>_<board> becomes CONFIG_TARGET_<board>, same for profiles.

git-svn-id: svn://svn.openwrt.org/openwrt/trunk@8653 3c298f89-4303-0410-b956-a3cf2f4a3e73

1 files changed, 0 insertions, 191 deletions

diff --git a/target/linux/adm5120-2.6/files/include/asm-mips/mach-adm5120/prom/myloader.h b/target/linux/adm5120-2.6/files/include/asm-mips/mach-adm5120/prom/myloader.h
deleted file mode 100644
index 526de865c..000000000
--- a/target/linux/adm5120-2.6/files/include/asm-mips/mach-adm5120/prom/myloader.h
+++ /dev/null
@@ -1,191 +0,0 @@
-/*
- *  $Id$
- *
- *  Compex's MyLoader specific definitions
- *
- *  Copyright (C) 2006,2007 Gabor Juhos <juhosg at openwrt.org>
- *  Copyright (C) 2007 OpenWrt.org
- *
- *  This program is free software; you can redistribute it and/or
- *  modify it under the terms of the GNU General Public License
- *  as published by the Free Software Foundation; either version 2
- *  of the License, or (at your option) any later version.
- *
- *  This program is distributed in the hope that it will be useful,
- *  but WITHOUT ANY WARRANTY; without even the implied warranty of
- *  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *  GNU General Public License for more details.
- *
- *  You should have received a copy of the GNU General Public License
- *  along with this program; if not, write to the
- *  Free Software Foundation, Inc., 51 Franklin Street, Fifth Floor,
- *  Boston, MA  02110-1301, USA.
- */
-
-#ifndef _MYLOADER_H_
-#define _MYLOADER_H_
-
-/*
- * Firmware file format:
- *
- *	<header>
- *	[<block descriptor 0>]
- *	...
- *	[<block descriptor n>]
- *	<null block descriptor>
- *	[<block data 0>]
- *	...
- *	[<block data n>]
- *
- *
- */
-
-/* Myloader specific magic numbers */
-#define MYLO_MAGIC_FIRMWARE	0x4C594D00
-#define MYLO_MAGIC_20021103	0x20021103
-#define MYLO_MAGIC_20021107	0x20021107
-
-#define MYLO_MAGIC_SYS_PARAMS	MYLO_MAGIC_20021107
-#define MYLO_MAGIC_PARTITIONS	MYLO_MAGIC_20021103
-#define MYLO_MAGIC_BOARD_PARAMS	MYLO_MAGIC_20021103
-
-/*
- * Addresses of the data structures provided by MyLoader
- */
-#define MYLO_MIPS_SYS_PARAMS	0x80000800	/* System Parameters */
-#define MYLO_MIPS_BOARD_PARAMS	0x80000A00	/* Board Parameters */
-#define MYLO_MIPS_PARTITIONS	0x80000C00	/* Partition Table */
-#define MYLO_MIPS_BOOT_PARAMS	0x80000E00	/* Boot Parameters */
-
-/* Vendor ID's (seems to be same as the PCI vendor ID's) */
-#define VENID_COMPEX		0x11F6
-
-/* Devices based on the ADM5120 */
-#define DEVID_COMPEX_NP27G	0x0078
-#define DEVID_COMPEX_NP28G	0x044C
-#define DEVID_COMPEX_NP28GHS	0x044E
-#define DEVID_COMPEX_WP54Gv1C	0x0514
-#define DEVID_COMPEX_WP54G	0x0515
-#define DEVID_COMPEX_WP54AG	0x0546
-#define DEVID_COMPEX_WPP54AG	0x0550
-#define DEVID_COMPEX_WPP54G	0x0555
-
-/* Devices based on the IXP422 */
-#define DEVID_COMPEX_WP18	0x047E
-#define DEVID_COMPEX_NP18A	0x0489
-
-/* Other devices */
-#define DEVID_COMPEX_NP26G8M	0x03E8
-#define DEVID_COMPEX_NP26G16M	0x03E9
-
-struct mylo_fw_header {
-	uint32_t	magic;	/* must be MYLO_MAGIC_FIRMWARE */
-	uint32_t	crc;	/* CRC of the whole firmware */
-	uint32_t	res0;	/* unknown/unused */
-	uint32_t	res1;	/* unknown/unused */
-	uint16_t	vid;	/* vendor ID */
-	uint16_t	did;	/* device ID */
-	uint16_t	svid;	/* sub vendor ID */
-	uint16_t	sdid;	/* sub device ID */
-	uint32_t	rev;	/* device revision */
-	uint32_t	fwhi;	/* FIXME: firmware version high? */
-	uint32_t	fwlo;	/* FIXME: firmware version low? */
-	uint32_t	flags;	/* firmware flags */
-};
-
-#define FW_FLAG_BOARD_PARAMS_WP	0x01 /* board parameters are write protected */
-#define FW_FLAG_BOOT_SECTOR_WE	0x02 /* enable of write boot sectors (below 64K) */
-
-struct mylo_fw_blockdesc {
-	uint32_t	type;	/* block type */
-	uint32_t	addr;	/* relative address to flash start */
-	uint32_t	dlen;	/* size of block data in bytes */
-	uint32_t	blen;	/* total size of block in bytes */
-};
-
-#define FW_DESC_TYPE_UNUSED	0
-#define FW_DESC_TYPE_USED	1
-
-struct mylo_partition {
-	uint16_t	flags;	/* partition flags */
-	uint16_t	type;	/* type of the partition */
-	uint32_t	addr;	/* relative address of the partition from the
-				   flash start */
-	uint32_t	size;	/* size of the partition in bytes */
-	uint32_t	param;	/* if this is the active partition, the
-				   MyLoader load code to this address */
-};
-
-#define PARTITION_FLAG_ACTIVE	0x8000 /* this is the active partition,
-					* MyLoader loads firmware from here */
-#define PARTITION_FLAG_ISRAM	0x2000 /* FIXME: this is a RAM partition? */
-#define PARTIIION_FLAG_RAMLOAD	0x1000 /* FIXME: load this partition into the RAM? */
-#define PARTITION_FLAG_PRELOAD	0x0800 /* the partition data preloaded to RAM
-					* before decompression */
-#define PARTITION_FLAG_HAVEHDR  0x0002 /* the partition data have a header */
-
-#define PARTITION_TYPE_FREE	0
-#define PARTITION_TYPE_USED	1
-
-#define MYLO_MAX_PARTITIONS	8	/* maximum number of partitions in the
-					   partition table */
-
-struct mylo_partition_table {
-	uint32_t	magic;	/* must be MYLO_MAGIC_PARTITIONS */
-	uint32_t	res0;	/* unknown/unused */
-	uint32_t	res1;	/* unknown/unused */
-	uint32_t 	res2;	/* unknown/unused */
-	struct mylo_partition partitions[MYLO_MAX_PARTITIONS];
-};
-
-struct mylo_partition_header {
-	uint32_t	len;	/* length of the partition data */
-	uint32_t	crc;	/* CRC value of the partition data */
-};
-
-struct mylo_system_params {
-	uint32_t	magic;	/* must be MYLO_MAGIC_SYS_PARAMS */
-	uint32_t	res0;
-	uint32_t	res1;
-	uint32_t	mylo_ver;
-	uint16_t	vid;	/* Vendor ID */
-	uint16_t	did;	/* Device ID */
-	uint16_t	svid;	/* Sub Vendor ID */
-	uint16_t	sdid;	/* Sub Device ID */
-	uint32_t	rev;	/* device revision */
-	uint32_t	fwhi;
-	uint32_t	fwlo;
-	uint32_t	tftp_addr;
-	uint32_t	prog_start;
-	uint32_t	flash_size;	/* Size of boot FLASH in bytes */
-	uint32_t	dram_size;	/* Size of onboard RAM in bytes */
-};
-
-
-struct mylo_eth_addr {
-	uint8_t	mac[6];
-	uint8_t	csum[2];
-};
-
-#define MYLO_ETHADDR_COUNT	8	/* maximum number of ethernet address
-					   in the board parameters */
-
-struct mylo_board_params {
-	uint32_t	magic;	/* must be MYLO_MAGIC_BOARD_PARAMS */
-	uint32_t	res0;
-	uint32_t	res1;
-	uint32_t	res2;
-	struct mylo_eth_addr addr[MYLO_ETHADDR_COUNT];
-};
-
-struct myloader_info {
-	u32	vid;
-	u32	did;
-	u32	svid;
-	u32	sdid;
-};
-
-extern struct myloader_info myloader_info;
-extern int myloader_present(void) __init;
-
-#endif /* _MYLOADER_H_*/