diff options
author | blogic <blogic@3c298f89-4303-0410-b956-a3cf2f4a3e73> | 2012-10-16 13:44:25 +0000 |
---|---|---|
committer | blogic <blogic@3c298f89-4303-0410-b956-a3cf2f4a3e73> | 2012-10-16 13:44:25 +0000 |
commit | a3a71d430b762ca48c6030c92d268a86b9f9137d (patch) | |
tree | 5937de88cb9dca7bfebc4dc3dce3cf904bf65357 /package/uboot-xburst/files/include/configs | |
parent | 05a3ece84affbb56ac43d1bf67b15d06bb354ca0 (diff) |
[boot] move boot related packages to their own folder
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33781 3c298f89-4303-0410-b956-a3cf2f4a3e73
Diffstat (limited to 'package/uboot-xburst/files/include/configs')
-rw-r--r-- | package/uboot-xburst/files/include/configs/avt2.h | 26 | ||||
-rw-r--r-- | package/uboot-xburst/files/include/configs/n516.h | 311 | ||||
-rw-r--r-- | package/uboot-xburst/files/include/configs/nanonote.h | 191 | ||||
-rw-r--r-- | package/uboot-xburst/files/include/configs/qi_lb60.h | 27 | ||||
-rw-r--r-- | package/uboot-xburst/files/include/configs/sakc.h | 200 |
5 files changed, 0 insertions, 755 deletions
diff --git a/package/uboot-xburst/files/include/configs/avt2.h b/package/uboot-xburst/files/include/configs/avt2.h deleted file mode 100644 index cbf34d720..000000000 --- a/package/uboot-xburst/files/include/configs/avt2.h +++ /dev/null @@ -1,26 +0,0 @@ -#ifndef __CONFIG_AVT2_H -#define __CONFIG_AVT2_H - -#include <configs/nanonote.h> - -#define CONFIG_AVT2 1 - -#define CONFIG_BOOTARGS "mem=64M console=ttyS0,57600n8 ubi.mtd=2 rootfstype=ubifs root=ubi0:rootfs rw rootwait avt2=1" -#define CONFIG_BOOTARGSFROMSD "mem=64M console=ttyS0,57600n8 rootfstype=ext2 root=/dev/mmcblk0p1 rw rootwait avt2=1" -#define CONFIG_BOOTCOMMAND "nand read 0x80600000 0x400000 0x200000;bootm" - -/* SDRAM paramters */ -#define SDRAM_BW16 1 /* Data bus width: 0-32bit, 1-16bit */ -#define SDRAM_BANK4 1 /* Banks each chip: 0-2bank, 1-4bank */ -#define SDRAM_ROW 13 /* Row address: 11 to 13 */ -#define SDRAM_COL 10 /* Column address: 8 to 12 */ -#define SDRAM_CASL 2 /* CAS latency: 2 or 3 */ - -/* SDRAM Timings, unit: ns */ -#define SDRAM_TRAS 45 /* RAS# Active Time */ -#define SDRAM_RCD 20 /* RAS# to CAS# Delay */ -#define SDRAM_TPC 20 /* RAS# Precharge Time */ -#define SDRAM_TRWL 7 /* Write Latency Time */ -#define SDRAM_TREF 15625 /* Refresh period: 8192 cycles/64ms */ - -#endif /* __CONFIG_AVT_H */ diff --git a/package/uboot-xburst/files/include/configs/n516.h b/package/uboot-xburst/files/include/configs/n516.h deleted file mode 100644 index c741bfe6c..000000000 --- a/package/uboot-xburst/files/include/configs/n516.h +++ /dev/null @@ -1,311 +0,0 @@ -/* - * (C) Copyright 2006 - * Ingenic Semiconductor, <jlwei@ingenic.cn> - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of - * the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, - * MA 02111-1307 USA - */ - -/* - * This file contains the configuration parameters for the pavo board. - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -//#define DEBUG -//#define DEBUG_SHELL - -#define CONFIG_MIPS32 1 /* MIPS32 CPU core */ -#define CONFIG_JzRISC 1 /* JzRISC core */ -#define CONFIG_JZSOC 1 /* Jz SoC */ -#define CONFIG_JZ4740 1 /* Jz4740 SoC */ -#define CONFIG_PAVO 1 /* PAVO validation board */ - -#define CONFIG_BOARD_NAME "n516" -#define CONFIG_BOARD_HWREV "1.0" -#define CONFIG_FIRMWARE_EPOCH "0" -#define CONFIG_UPDATE_TMPBUF 0x80600000 -#define CONFIG_UPDATE_CHUNKSIZE 0x800000 -#define CONFIG_UPDATE_FILENAME "update.oifw" -#define CONFIG_UPDATE_FILEEXT ".oifw" -#define CONFIG_UBI_PARTITION "UBI" - -#define CONFIG_SKIP_LOWLEVEL_INIT 1 -#undef CONFIG_SKIP_RELOCATE_UBOOT - -#if 0 -#define CONFIG_LCD /* LCD support */ -#define CONFIG_JZLCD_METRONOME_800x600 -#define LCD_BPP LCD_COLOR8 - -#define WFM_DATA_SIZE ( 1 << 14 ) -#define CONFIG_METRONOME_WF_LEN (64 * (1 << 10)) -#define CONFIG_METRONOME_WF_NAND_OFFSET (0x100000) -#define BMP_LOGO_HEIGHT 0 -#define CONFIG_UBI_WF_VOLUME "waveforms" -#define CONFIG_UBI_BOOTSPLASH_VOLUME "bootsplash" -#define CONFIG_METRONOME_BOOTSPLASH_LEN 480000 -#endif - -#if 0 -#define CONFIG_JZSOC_I2C -#define CONFIG_HARD_I2C -#define CONFIG_SYS_I2C_SPEED 100000 -#define CONFIG_SYS_I2C_SLAVE 0 -#define CONFIG_LPC_I2C_ADDR 0x54 -#endif - -#define JZ4740_NORBOOT_CFG JZ4740_NORBOOT_16BIT /* NOR Boot config code */ -#define JZ4740_NANDBOOT_CFG JZ4740_NANDBOOT_B8R3 /* NAND Boot config code */ - -#define CONFIG_SYS_CPU_SPEED 336000000 /* CPU clock: 336 MHz */ -#define CONFIG_SYS_EXTAL 12000000 /* EXTAL freq: 12 MHz */ -#define CONFIG_SYS_HZ (CONFIG_SYS_EXTAL/256) /* incrementer freq */ - -#define CONFIG_SYS_UART_BASE UART0_BASE /* Base of the UART channel */ - -#define CONFIG_BAUDRATE 57600 -#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } - - -#define CONFIG_MMC 1 -#define CONFIG_GENERIC_MMC 1 -#define CONFIG_JZ_MMC 1 -#define CONFIG_FAT 1 - -#define CONFIG_SYS_HUSH_PARSER -#define CONFIG_SYS_PROMPT_HUSH_PS2 ">" -#define CONFIG_CMDLINE_EDITING - -/* allow to overwrite serial and ethaddr */ -#define CONFIG_ENV_OVERWRITE - -#include <config_cmd_default.h> - -#undef CONFIG_CMD_BDI /* bdinfo */ -#undef CONFIG_CMD_FPGA -#undef CONFIG_CMD_ECHO /* echo arguments */ -#undef CONFIG_CMD_FLASH /* flinfo, erase, protect */ -#undef CONFIG_CMD_FPGA /* FPGA configuration Support */ -#undef CONFIG_CMD_IMI /* iminfo */ -#undef CONFIG_CMD_ITEST /* Integer (and string) test */ -#undef CONFIG_CMD_LOADB /* loadb */ -#undef CONFIG_CMD_LOADS /* loads */ -#undef CONFIG_CMD_NFS /* NFS support */ -#undef CONFIG_CMD_SETGETDCR /* DCR support on 4xx */ -#undef CONFIG_CMD_SOURCE /* "source" command support */ -#undef CONFIG_CMD_XIMG /* Load part of Multi Image */ -#undef CONFIG_CMD_NET - -//#define CONFIG_CMD_ASKENV -//#define CONFIG_CMD_DHCP -//#define CONFIG_CMD_PING -#define CONFIG_CMD_NAND -#define CONFIG_CMD_MMC -#define CONFIG_CMD_FAT -/*#define CONFIG_CMD_UBI*/ -/*#define CONFIG_CMD_MTDPARTS*/ -//#define CONFIG_CMD_JFFS2 -//#define CONFIG_JFFS2_NAND -//#define CONFIG_JFFS2_CMDLINE -#define CONFIG_CMD_UPDATE - -#define CONFIG_DOS_PARTITION - -/*#define CONFIG_MTD_PARTITIONS*/ -#define CONFIG_RBTREE - -#define CONFIG_BOOTP_MASK ( CONFIG_BOOTP_DEFAUL ) - -/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ -#if 0 -#define CONFIG_ZERO_BOOTDELAY_CHECK -#define CONFIG_BOOTDELAY 0 -#define CONFIG_BOOTFILE uImage /* file to load */ -#define CONFIG_BOOTARGS "mem=64M console=ttyS0,57600n8 ip=off rootfstype=ubifs root=ubi:rootfs ubi.mtd=UBI rw panic=5 " MTDPARTS_DEFAULT -#define CONFIG_BOOTCOMMAND "check_and_update; setenv bootargs $bootargs $batt_level_param; ubi read 0x80600000 bootsplash && show_image 0x80600000; ubi read 0x80600000 kernel; bootm 0x80600000; ubi read 0x80600000 errorsplash && show_image 0x80600000; while test 0 = 0; do check_and_update; done" -#define CONFIG_SYS_AUTOLOAD "n" /* No autoload */ -#define CONFIG_IPADDR 192.168.111.1 -#define CONFIG_SERVERIP 192.168.111.2 -#define MTDIDS_DEFAULT "nand0=jz4740-nand" -#define MTDPARTS_DEFAULT "mtdparts=jz4740-nand:1M@0(uboot)ro,-@1M(UBI)" -#define CONFIG_EXTRA_ENV_SETTINGS "mtdids=nand0=jz4740-nand\0mtdparts=mtdparts=jz4740-nand:1M@0(uboot)ro,-@1M(UBI)\0" \ - "stdout=serial\0stderr=lcd\0" -#endif - -#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAUL) -#define CONFIG_BOOTDELAY 0 -#define CONFIG_BOOTFILE "uImage" /* file to load */ -#define CONFIG_BOOTARGS "mem=64M console=ttyS0,57600n8 ubi.mtd=2 rootfstype=ubifs root=ubi0:rootfs rw rootwait" -#define CONFIG_BOOTCOMMAND "nand read 0x80600000 0x400000 0x200000;bootm" - - - -#define CONFIG_SYS_CONSOLE_IS_IN_ENV - -/* - * Serial download configuration - * - */ -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#define CONFIG_SYS_PROMPT "n516 # " /* Monitor Command Prompt */ -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args*/ - -#define CONFIG_SYS_MALLOC_LEN 1024*1024*2 -#define CONFIG_SYS_BOOTPARAMS_LEN 128*1024 - -#define CONFIG_SYS_SDRAM_BASE 0x80000000 /* Cached addr */ - -#define CONFIG_SYS_INIT_SP_OFFSET 0x400000 - -#define CONFIG_SYS_LOAD_ADDR 0x80600000 /* default load address */ - -#define CONFIG_SYS_MEMTEST_START 0x80100000 -#define CONFIG_SYS_MEMTEST_END 0x80800000 - -/*----------------------------------------------------------------------- - * Environment - *----------------------------------------------------------------------*/ -#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL) -#define CONFIG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */ -#else -#define CONFIG_ENV_IS_IN_NAND 1 /* use NAND for environment vars */ -#endif - -/*----------------------------------------------------------------------- - * NAND FLASH configuration - */ -#define CONFIG_SYS_MAX_NAND_DEVICE 1 -#define NAND_MAX_CHIPS 1 -#define CONFIG_SYS_NAND_BASE 0xB8000000 -#define CONFIG_SYS_NAND_SELECT_DEVICE 1 /* nand driver supports mutipl. chips */ - -/* - * IPL (Initial Program Loader, integrated inside CPU) - * Will load first 8k from NAND (SPL) into cache and execute it from there. - * - * SPL (Secondary Program Loader) - * Will load special U-Boot version (NUB) from NAND and execute it. This SPL - * has to fit into 8kByte. It sets up the CPU and configures the SDRAM - * controller and the NAND controller so that the special U-Boot image can be - * loaded from NAND to SDRAM. - * - * NUB (NAND U-Boot) - * This NAND U-Boot (NUB) is a special U-Boot version which can be started - * from RAM. Therefore it mustn't (re-)configure the SDRAM controller. - * - */ -#define CONFIG_SYS_NAND_U_BOOT_DST 0x80100000 /* Load NUB to this addr */ -#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_NAND_U_BOOT_DST /* Start NUB from this addr */ - -/* - * Define the partitioning of the NAND chip (only RAM U-Boot is needed here) - */ -#define CONFIG_SYS_NAND_U_BOOT_OFFS (256 << 10) /* Offset to RAM U-Boot image */ -#define CONFIG_SYS_NAND_U_BOOT_SIZE (512 << 10) /* Size of RAM U-Boot image */ - -#define CONFIG_SYS_NAND_PAGE_SIZE 2048 -#define CONFIG_SYS_NAND_BLOCK_SIZE (128 << 10) /* NAND chip block size */ -#define CONFIG_SYS_NAND_BADBLOCK_PAGE 63 /* NAND bad block was marked at this page in a block, starting from 0 */ -#define CONFIG_SYS_NAND_ECC_POS 6 - -#ifdef CONFIG_ENV_IS_IN_NAND -//#define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE -#define CONFIG_ENV_SIZE (128 * 1024) -//#define CONFIG_ENV_OFFSET (CONFIG_SYS_NAND_BLOCK_SIZE + CONFIG_SYS_NAND_U_BOOT_SIZE + CONFIG_SYS_NAND_BLOCK_SIZE) /* environment starts here */ -#define CONFIG_ENV_OFFSET (CONFIG_SYS_NAND_U_BOOT_SIZE + CONFIG_SYS_NAND_U_BOOT_OFFS) -//#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE) -#endif - - -/*----------------------------------------------------------------------- - * NOR FLASH and environment organization - */ -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ -#define CONFIG_SYS_MAX_FLASH_SECT (128) /* max number of sectors on one chip */ - -#define PHYS_FLASH_1 0xa8000000 /* Flash Bank #1 */ - -/* The following #defines are needed to get flash environment right */ -#define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* in pavo/config.mk TEXT_BASE=0x88000000*/ -#define CONFIG_SYS_SYS_MONITOR_BASE TEXT_BASE /* in pavo/config.mk TEXT_BASE=0x88000000*/ -#define CONFIG_SYS_MONITOR_LEN (256*1024) /* Reserve 256 kB for Monitor */ - -#define CONFIG_SYS_FLASH_BASE PHYS_FLASH_1 - -/* timeout values are in ticks */ -#define CONFIG_SYS_FLASH_ERASE_TOUT (2 * CONFIG_SYS_HZ) /* Timeout for Flash Erase */ -#define CONFIG_SYS_FLASH_WRITE_TOUT (2 * CONFIG_SYS_HZ) /* Timeout for Flash Write */ - -#ifdef CONFIG_ENV_IS_IN_FLASH -#define CONFIG_ENV_IS_NOWHERE 1 -#define CONFIG_ENV_ADDR 0xa8040000 -#define CONFIG_ENV_SIZE 0x20000 -#endif - -/*----------------------------------------------------------------------- - * SDRAM Info. - */ -#define CONFIG_NR_DRAM_BANKS 1 - -// SDRAM paramters -#define SDRAM_BW16 0 /* Data bus width: 0-32bit, 1-16bit */ -#define SDRAM_BANK4 1 /* Banks each chip: 0-2bank, 1-4bank */ -#define SDRAM_ROW 13 /* Row address: 11 to 13 */ -#define SDRAM_COL 9 /* Column address: 8 to 12 */ -#define SDRAM_CASL 2 /* CAS latency: 2 or 3 */ - -// SDRAM Timings, unit: ns -#define SDRAM_TRAS 45 /* RAS# Active Time */ -#define SDRAM_RCD 20 /* RAS# to CAS# Delay */ -#define SDRAM_TPC 20 /* RAS# Precharge Time */ -#define SDRAM_TRWL 7 /* Write Latency Time */ -#define SDRAM_TREF 15625 /* Refresh period: 4096 refresh cycles/64ms */ - -/*----------------------------------------------------------------------- - * Cache Configuration - */ -#define CONFIG_SYS_DCACHE_SIZE 16384 -#define CONFIG_SYS_ICACHE_SIZE 16384 -#define CONFIG_SYS_CACHELINE_SIZE 32 - -/*----------------------------------------------------------------------- - * GPIO definition - */ -#define GPIO_SD_VCC_EN_N 113 /* GPD17 */ -#define GPIO_SD_CD_N 103 /* GPD7 */ -#define GPIO_SD_WP 111 /* GPD15 */ -#define GPIO_USB_DETE 115 /* GPD6 */ -//#define GPIO_DC_DETE_N 103 /* GPD7 */ -#define GPIO_CHARG_STAT_N 112 /* GPD15 */ -#define GPIO_DISP_OFF_N 97 /* GPD1 */ -#define GPIO_UDC_HOTPLUG 100 /* GPD4 */ -#define GPIO_LED_EN 124 /* GPD28 */ - -#define GPIO_RST_L 50 /* GPB18 LCD_SPL */ -#define GPIO_LCDRDY 49 /* GPB17 LCD_CLS */ -#define GPIO_STBY 86 /* GPC22 LCD_PS */ -#define GPIO_ERR 87 /* GPC23 LCD_REV */ - -#endif /* __CONFIG_H */ diff --git a/package/uboot-xburst/files/include/configs/nanonote.h b/package/uboot-xburst/files/include/configs/nanonote.h deleted file mode 100644 index 8926877ab..000000000 --- a/package/uboot-xburst/files/include/configs/nanonote.h +++ /dev/null @@ -1,191 +0,0 @@ -/* - * Authors: Xiangfu Liu <xiangfu.z@gmail.com> - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License - * as published by the Free Software Foundation; either version - * 3 of the License, or (at your option) any later version. - */ - -/* - * This file contains the configuration parameters for the NanoNote. - */ -#ifndef __CONFIG_NANONOTE_H -#define __CONFIG_NANONOTE_H - -#define CONFIG_MIPS32 1 /* MIPS32 CPU core */ -#define CONFIG_JzRISC 1 /* JzRISC core */ -#define CONFIG_JZSOC 1 /* Jz SoC */ -#define CONFIG_JZ4740 1 /* Jz4740 SoC */ -#define CONFIG_NANONOTE 1 - -#define CONFIG_LCD 1 /* LCD support */ -#define LCD_BPP LCD_COLOR32 /*5:18,24,32 bits per pixel */ -#define CONFIG_SYS_WHITE_ON_BLACK 1 - -#define CONFIG_SYS_CPU_SPEED 336000000 /* CPU clock: 336 MHz */ -#define CONFIG_SYS_EXTAL 12000000 /* EXTAL freq: 12 MHz */ -#define CONFIG_SYS_HZ (CONFIG_SYS_EXTAL / 256) /* incrementer freq */ -#define CONFIG_SYS_MIPS_TIMER_FREQ CONFIG_SYS_CPU_SPEED - -#define CONFIG_SYS_UART_BASE UART0_BASE /* Base of the UART channel */ -#define CONFIG_BAUDRATE 57600 -#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } - -#define CONFIG_MMC 1 -#define CONFIG_FAT 1 -#define CONFIG_DOS_PARTITION 1 -#define CONFIG_SKIP_LOWLEVEL_INIT 1 -#define CONFIG_BOARD_EARLY_INIT_F 1 -#define CONFIG_SYS_NO_FLASH 1 -#define CONFIG_ENV_OVERWRITE 1 - -#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAUL) -#define CONFIG_BOOTDELAY 0 -#define CONFIG_BOOTFILE "uImage" /* file to load */ -/* - * Command line configuration. - */ -#define CONFIG_CMD_BOOTD /* bootd */ -#define CONFIG_CMD_CONSOLE /* coninfo */ -#define CONFIG_CMD_ECHO /* echo arguments */ - -#define CONFIG_CMD_LOADB /* loadb */ -#define CONFIG_CMD_LOADS /* loads */ -#define CONFIG_CMD_MEMORY /* md mm nm mw cp cmp crc base loop mtest */ -#define CONFIG_CMD_MISC /* Misc functions like sleep etc*/ -#define CONFIG_CMD_RUN /* run command in env variable */ -#define CONFIG_CMD_SAVEENV /* saveenv */ -#define CONFIG_CMD_SETGETDCR /* DCR support on 4xx */ -#define CONFIG_CMD_SOURCE /* "source" command support */ - -#define CONFIG_CMD_NAND -#define CONFIG_CMD_MMC -#define CONFIG_CMD_FAT - -/* - * Serial download configuration - */ -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CONFIG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#define CONFIG_SYS_PROMPT "QI# " /* Monitor Command Prompt */ -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) -/* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args*/ - -#define CONFIG_SYS_MALLOC_LEN 896 * 1024 -#define CONFIG_SYS_BOOTPARAMS_LEN 128 * 1024 - -#define CONFIG_SYS_SDRAM_BASE 0x80000000 /* Cached addr */ -#define CONFIG_SYS_INIT_SP_OFFSET 0x400000 -#define CONFIG_SYS_LOAD_ADDR 0x80600000 /* default load address */ -#define CONFIG_SYS_MEMTEST_START 0x80100000 -#define CONFIG_SYS_MEMTEST_END 0x80800000 - -/* - * Environment - */ -#define CONFIG_ENV_IS_IN_NAND 1 /* use NAND for environment vars */ - -/* - * NAND FLASH configuration - */ -/* NAND Boot config code */ -#define JZ4740_NANDBOOT_CFG JZ4740_NANDBOOT_B8R3 - -#define NANONOTE_NAND_SIZE 2 /* if board nand flash is 1GB, set to 1 - * if board nand flash is 2GB, set to 2 - * for change the PAGE_SIZE and BLOCK_SIZE - * will delete when there is no 1GB flash - */ - -#define CONFIG_SYS_NAND_PAGE_SIZE (2048 * NANONOTE_NAND_SIZE) -/* nand chip block size */ -#define CONFIG_SYS_NAND_BLOCK_SIZE (256 * NANONOTE_NAND_SIZE << 10) -/* nand bad block was marked at this page in a block, start from 0 */ -#define CONFIG_SYS_NAND_BADBLOCK_PAGE 127 -/* ECC offset position in oob area, default value is 6 if it isn't defined */ -#define CONFIG_SYS_NAND_ECC_POS (6 * NANONOTE_NAND_SIZE) -#define CONFIG_SYS_MAX_NAND_DEVICE 1 -#define NAND_MAX_CHIPS 1 -#define CONFIG_SYS_NAND_BASE 0xB8000000 -#define CONFIG_SYS_NAND_SELECT_DEVICE 1 /* nand driver supports mutipl.*/ -#define CONFIG_SYS_ONENAND_BASE CONFIG_SYS_NAND_BASE - -/* - * IPL (Initial Program Loader, integrated inside CPU) - * Will load first 8k from NAND (SPL) into cache and execute it from there. - * - * SPL (Secondary Program Loader) - * Will load special U-Boot version (NUB) from NAND and execute it. This SPL - * has to fit into 8kByte. It sets up the CPU and configures the SDRAM - * controller and the NAND controller so that the special U-Boot image can be - * loaded from NAND to SDRAM. - * - * NUB (NAND U-Boot) - * This NAND U-Boot (NUB) is a special U-Boot version which can be started - * from RAM. Therefore it mustn't (re-)configure the SDRAM controller. - * - */ -#define CONFIG_SYS_NAND_U_BOOT_DST 0x80100000 /* Load NUB to this addr */ -#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_NAND_U_BOOT_DST -/* Start NUB from this addr*/ - -/* - * Define the partitioning of the NAND chip (only RAM U-Boot is needed here) - */ -#define CONFIG_SYS_NAND_U_BOOT_OFFS (256 << 10) /* Offset to RAM U-Boot image */ -#define CONFIG_SYS_NAND_U_BOOT_SIZE (512 << 10) /* Size of RAM U-Boot image */ - -#define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE -#define CONFIG_ENV_OFFSET (CONFIG_SYS_NAND_BLOCK_SIZE + CONFIG_SYS_NAND_U_BOOT_SIZE + CONFIG_SYS_NAND_BLOCK_SIZE) -/* environment starts here */ -#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE) - -/* in board/nanonote/config.mk TEXT_BAS = 0x88000000 */ -#define CONFIG_SYS_MONITOR_BASE TEXT_BASE - -/* - * SDRAM Info. - */ -#define CONFIG_NR_DRAM_BANKS 1 - -/* - * Cache Configuration - */ -#define CONFIG_SYS_DCACHE_SIZE 16384 -#define CONFIG_SYS_ICACHE_SIZE 16384 -#define CONFIG_SYS_CACHELINE_SIZE 32 - -/* - * GPIO definition - */ -#define GPIO_LCD_CS (2 * 32 + 21) -#define GPIO_DISP_OFF_N (3 * 32 + 21) -#define GPIO_PWM (3 * 32 + 27) - -#define GPIO_AMP_EN (3 * 32 + 4) - -#define GPIO_SDPW_EN (3 * 32 + 2) -#define GPIO_SD_DETECT (3 * 32 + 0) - -#define GPIO_USB_DETECT (3 * 32 + 27) -#define GPIO_BUZZ_PWM (3 * 32 + 28) - -#define GPIO_AUDIO_POP (1 * 32 + 29) -#define GPIO_COB_TEST (1 * 32 + 30) - -#define GPIO_KEYOUT_BASE (2 * 32 + 10) -#define GPIO_KEYIN_BASE (3 * 32 + 18) -#define GPIO_KEYIN_8 (3 * 32 + 26) - -#define GPIO_SD_CD_N GPIO_SD_DETECT /* SD Card insert detect */ -#define GPIO_SD_VCC_EN_N GPIO_SDPW_EN /* SD Card Power Enable */ - -#endif /* __CONFIG_NANONOTE_H */ diff --git a/package/uboot-xburst/files/include/configs/qi_lb60.h b/package/uboot-xburst/files/include/configs/qi_lb60.h deleted file mode 100644 index 1542c3dd6..000000000 --- a/package/uboot-xburst/files/include/configs/qi_lb60.h +++ /dev/null @@ -1,27 +0,0 @@ -#ifndef __CONFIG_QI_LB60_H -#define __CONFIG_QI_LB60_H - -#include <configs/nanonote.h> - -#define CONFIG_QI_LB60 1 - -#define CONFIG_BOOTARGS "mem=32M console=ttyS0,57600n8 ubi.mtd=2 rootfstype=ubifs root=ubi0:rootfs rw rootwait" -#define CONFIG_BOOTARGSFROMSD "mem=32M console=ttyS0,57600n8 rootfstype=ext2 root=/dev/mmcblk0p2 rw rootwait" -#define CONFIG_BOOTCOMMAND "nand read 0x80600000 0x400000 0x200000;bootm" -#define CONFIG_BOOTCOMMANDFROMSD "mmc init; fatload mmc 0 0x80600000 uImage; bootm" - -/* SDRAM paramters */ -#define SDRAM_BW16 1 /* Data bus width: 0-32bit, 1-16bit */ -#define SDRAM_BANK4 1 /* Banks each chip: 0-2bank, 1-4bank */ -#define SDRAM_ROW 13 /* Row address: 11 to 13 */ -#define SDRAM_COL 9 /* Column address: 8 to 12 */ -#define SDRAM_CASL 2 /* CAS latency: 2 or 3 */ - -/* SDRAM Timings, unit: ns */ -#define SDRAM_TRAS 45 /* RAS# Active Time */ -#define SDRAM_RCD 20 /* RAS# to CAS# Delay */ -#define SDRAM_TPC 20 /* RAS# Precharge Time */ -#define SDRAM_TRWL 7 /* Write Latency Time */ -#define SDRAM_TREF 15625 /* Refresh period: 8192 cycles/64ms */ - -#endif diff --git a/package/uboot-xburst/files/include/configs/sakc.h b/package/uboot-xburst/files/include/configs/sakc.h deleted file mode 100644 index b88d8b08b..000000000 --- a/package/uboot-xburst/files/include/configs/sakc.h +++ /dev/null @@ -1,200 +0,0 @@ -/* - * Authors: Xiangfu Liu <xiangfu.z@gmail.com> - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License - * as published by the Free Software Foundation; either version - * 3 of the License, or (at your option) any later version. - */ - -/* - * This file contains the configuration parameters for SAKC. - */ -#ifndef __CONFIG_H -#define __CONFIG_H - -#define DEBUG -#define CONFIG_MIPS32 1 /* MIPS32 CPU core */ -#define CONFIG_JzRISC 1 /* JzRISC core */ -#define CONFIG_JZSOC 1 /* Jz SoC */ -#define CONFIG_JZ4725 1 /* Jz4725 SoC */ -#define CONFIG_JZ4740 1 /* Jz4740 SoC */ -#define CONFIG_SAKC 1 /* SAKC board */ - -#define MMC_BUS_WIDTH_1BIT 1 /* 1 for MMC 1Bit Bus Width */ - -//#define CONFIG_LCD 1 /* LCD support */ -//#define LCD_BPP LCD_COLOR32 /*5:18,24,32 bits per pixel */ -//#define CONFIG_SYS_WHITE_ON_BLACK 1 - -#define CONFIG_SYS_CPU_SPEED 336000000 /* CPU clock: 336 MHz */ -#define CONFIG_SYS_EXTAL 12000000 /* EXTAL freq: 12 MHz */ -#define CONFIG_SYS_HZ (CONFIG_SYS_EXTAL / 256) /* incrementer freq */ -#define CONFIG_SYS_MIPS_TIMER_FREQ CONFIG_SYS_CPU_SPEED - -#define CONFIG_SYS_UART_BASE UART0_BASE /* Base of the UART channel */ -#define CONFIG_BAUDRATE 57600 -#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } - -#define CONFIG_MMC 1 -#define CONFIG_FAT 1 -#define CONFIG_DOS_PARTITION 1 -#define CONFIG_SKIP_LOWLEVEL_INIT 1 -#define CONFIG_BOARD_EARLY_INIT_F 1 -#define CONFIG_SYS_NO_FLASH 1 -#define CONFIG_ENV_OVERWRITE 1 - -#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAUL) -#define CONFIG_BOOTDELAY 3 -#define CONFIG_BOOTFILE "uImage" /* file to load */ -#define CONFIG_BOOTARGS "mem=32M console=ttyS0,57600n8 ubi.mtd=2 rootfstype=ubifs root=ubi0:rootfs rw rootwait" -#define CONFIG_EXTRA_ENV_SETTINGS 1 -#define CONFIG_BOOTARGSFROMSD "mem=32M console=ttyS0,57600n8 rootfstype=ext2 root=/dev/mmcblk0p1 rw rootwait" -#define CONFIG_BOOTCOMMAND "nand read 0x80600000 0x400000 0x200000;bootm" - -/* - * Command line configuration. - */ -#define CONFIG_CMD_BDI /* bdinfo */ -#define CONFIG_CMD_BOOTD /* bootd */ -#define CONFIG_CMD_CONSOLE /* coninfo */ -#define CONFIG_CMD_ECHO /* echo arguments */ -#define CONFIG_CMD_IMI /* iminfo */ -#define CONFIG_CMD_ITEST /* Integer (and string) test */ - -#define CONFIG_CMD_LOADB /* loadb */ -#define CONFIG_CMD_LOADS /* loads */ -#define CONFIG_CMD_MEMORY /* md mm nm mw cp cmp crc base loop mtest */ -#define CONFIG_CMD_MISC /* Misc functions like sleep etc*/ -#define CONFIG_CMD_RUN /* run command in env variable */ -#define CONFIG_CMD_SAVEENV /* saveenv */ -#define CONFIG_CMD_SETGETDCR /* DCR support on 4xx */ -#define CONFIG_CMD_SOURCE /* "source" command support */ -#define CONFIG_CMD_XIMG /* Load part of Multi Image */ - -#define CONFIG_CMD_NAND -#define CONFIG_CMD_MMC -#define CONFIG_CMD_FAT - -/* - * Serial download configuration - */ -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CONFIG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#define CONFIG_SYS_PROMPT "SAKC# " /* Monitor Command Prompt */ -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) -/* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args*/ - -#define CONFIG_SYS_MALLOC_LEN 128 * 1024 -#define CONFIG_SYS_BOOTPARAMS_LEN 128 * 1024 - -#define CONFIG_SYS_SDRAM_BASE 0x80000000 /* Cached addr */ -#define CONFIG_SYS_INIT_SP_OFFSET 0x400000 -#define CONFIG_SYS_LOAD_ADDR 0x80600000 /* default load address */ -#define CONFIG_SYS_MEMTEST_START 0x80100000 -#define CONFIG_SYS_MEMTEST_END 0x80800000 - -/* - * Environment - */ -#define CONFIG_ENV_IS_IN_NAND 1 /* use NAND for environment vars */ - -/* - * NAND FLASH configuration - */ -/* NAND Boot config code */ -#define JZ4740_NANDBOOT_CFG JZ4740_NANDBOOT_B8R3 - -#define SAKC_NAND_SIZE 1 /* if board nand flash is 1GB, set to 1 - * if board nand flash is 2GB, set to 2 - * for change the PAGE_SIZE and BLOCK_SIZE - * will delete when there is no 1GB flash - */ - -#define CONFIG_SYS_NAND_PAGE_SIZE (2048 * SAKC_NAND_SIZE) -/* nand chip block size */ -#define CONFIG_SYS_NAND_BLOCK_SIZE (256 * SAKC_NAND_SIZE << 10) -/* nand bad block was marked at this page in a block, start from 0 */ -#define CONFIG_SYS_NAND_BADBLOCK_PAGE 127 -/* ECC offset position in oob area, default value is 6 if it isn't defined */ -#define CONFIG_SYS_NAND_ECC_POS (6 * SAKC_NAND_SIZE) -#define CONFIG_SYS_MAX_NAND_DEVICE 1 -#define NAND_MAX_CHIPS 1 -#define CONFIG_SYS_NAND_BASE 0xB8000000 -#define CONFIG_SYS_NAND_SELECT_DEVICE 1 /* nand driver supports mutipl.*/ -#define CONFIG_SYS_ONENAND_BASE CONFIG_SYS_NAND_BASE - -/* - * IPL (Initial Program Loader, integrated inside CPU) - * Will load first 8k from NAND (SPL) into cache and execute it from there. - * - * SPL (Secondary Program Loader) - * Will load special U-Boot version (NUB) from NAND and execute it. This SPL - * has to fit into 8kByte. It sets up the CPU and configures the SDRAM - * controller and the NAND controller so that the special U-Boot image can be - * loaded from NAND to SDRAM. - * - * NUB (NAND U-Boot) - * This NAND U-Boot (NUB) is a special U-Boot version which can be started - * from RAM. Therefore it mustn't (re-)configure the SDRAM controller. - * - */ -#define CONFIG_SYS_NAND_U_BOOT_DST 0x80100000 /* Load NUB to this addr */ -#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_NAND_U_BOOT_DST -/* Start NUB from this addr*/ - -/* - * Define the partitioning of the NAND chip (only RAM U-Boot is needed here) - */ -#define CONFIG_SYS_NAND_U_BOOT_OFFS (256 << 10) /* Offset to RAM U-Boot image */ -#define CONFIG_SYS_NAND_U_BOOT_SIZE (512 << 10) /* Size of RAM U-Boot image */ - -#define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE -#define CONFIG_ENV_OFFSET (CONFIG_SYS_NAND_BLOCK_SIZE + CONFIG_SYS_NAND_U_BOOT_SIZE + CONFIG_SYS_NAND_BLOCK_SIZE) -/* environment starts here */ -#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE) - -/* in qi_lb60.h/config.mk TEXT_BAS = 0x88000000 */ -#define CONFIG_SYS_MONITOR_BASE TEXT_BASE - -/* - * SDRAM Info. - */ -#define CONFIG_NR_DRAM_BANKS 1 - -/* SDRAM paramters */ -#define SDRAM_BW16 1 /* Data bus width: 0-32bit, 1-16bit */ -#define SDRAM_BANK4 1 /* Banks each chip: 0-2bank, 1-4bank */ -#define SDRAM_ROW 13 /* Row address: 11 to 13 */ -#define SDRAM_COL 9 /* Column address: 8 to 12 */ -#define SDRAM_CASL 2 /* CAS latency: 2 or 3 */ - -/* SDRAM Timings, unit: ns */ -#define SDRAM_TRAS 45 /* RAS# Active Time */ -#define SDRAM_RCD 20 /* RAS# to CAS# Delay */ -#define SDRAM_TPC 20 /* RAS# Precharge Time */ -#define SDRAM_TRWL 7 /* Write Latency Time */ -#define SDRAM_TREF 15625 /* Refresh period: 8192 cycles/64ms */ - -/* - * Cache Configuration - */ -#define CONFIG_SYS_DCACHE_SIZE 16384 -#define CONFIG_SYS_ICACHE_SIZE 16384 -#define CONFIG_SYS_CACHELINE_SIZE 32 - -/* - * GPIO definition - */ -#define GPIO_SD_DETECT (2 * 32 + 27) -#define GPIO_SD_CD_N GPIO_SD_DETECT /* SD Card insert detect */ -#define GPIO_SD_VCC_EN_N GPIO_SDPW_EN /* SD Card Power Enable */ - -#endif /* __CONFIG_H */ |