[package] Add uboot for xburst package

git-svn-id: svn://svn.openwrt.org/openwrt/trunk@20832 3c298f89-4303-0410-b956-a3cf2f4a3e73

1 files changed, 200 insertions, 0 deletions

diff --git a/package/uboot-xburst/files/include/configs/sakc.h b/package/uboot-xburst/files/include/configs/sakc.h
new file mode 100644
index 000000000..b88d8b08b
--- /dev/null
+++ b/package/uboot-xburst/files/include/configs/sakc.h
@@ -0,0 +1,200 @@
+/*
+ * Authors: Xiangfu Liu <xiangfu.z@gmail.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version
+ * 3 of the License, or (at your option) any later version.
+ */
+
+/*
+ * This file contains the configuration parameters for SAKC.
+ */
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#define DEBUG
+#define CONFIG_MIPS32		1  /* MIPS32 CPU core */
+#define CONFIG_JzRISC		1  /* JzRISC core */
+#define CONFIG_JZSOC		1  /* Jz SoC */
+#define CONFIG_JZ4725		1  /* Jz4725 SoC */
+#define CONFIG_JZ4740		1  /* Jz4740 SoC */
+#define CONFIG_SAKC			1  /* SAKC board */
+
+#define MMC_BUS_WIDTH_1BIT	1  /* 1 for MMC  1Bit Bus Width */
+
+//#define CONFIG_LCD		1  /* LCD support */
+//#define LCD_BPP			LCD_COLOR32	/*5:18,24,32 bits per pixel */
+//#define CONFIG_SYS_WHITE_ON_BLACK	1
+
+#define CONFIG_SYS_CPU_SPEED	336000000	/* CPU clock: 336 MHz */
+#define CONFIG_SYS_EXTAL		12000000	/* EXTAL freq: 12 MHz */
+#define CONFIG_SYS_HZ		(CONFIG_SYS_EXTAL / 256) /* incrementer freq */
+#define CONFIG_SYS_MIPS_TIMER_FREQ	CONFIG_SYS_CPU_SPEED
+
+#define CONFIG_SYS_UART_BASE	UART0_BASE	/* Base of the UART channel */
+#define CONFIG_BAUDRATE		57600
+#define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }
+
+#define CONFIG_MMC      	1
+#define CONFIG_FAT      	1  
+#define CONFIG_DOS_PARTITION	1
+#define CONFIG_SKIP_LOWLEVEL_INIT	1
+#define CONFIG_BOARD_EARLY_INIT_F	1
+#define CONFIG_SYS_NO_FLASH	1
+#define CONFIG_ENV_OVERWRITE	1
+
+#define CONFIG_BOOTP_MASK	(CONFIG_BOOTP_DEFAUL)
+#define CONFIG_BOOTDELAY	3
+#define CONFIG_BOOTFILE		"uImage"	/* file to load */
+#define CONFIG_BOOTARGS		"mem=32M console=ttyS0,57600n8 ubi.mtd=2 rootfstype=ubifs root=ubi0:rootfs rw rootwait"
+#define CONFIG_EXTRA_ENV_SETTINGS	1
+#define CONFIG_BOOTARGSFROMSD	"mem=32M console=ttyS0,57600n8 rootfstype=ext2 root=/dev/mmcblk0p1 rw rootwait"
+#define CONFIG_BOOTCOMMAND	"nand read 0x80600000 0x400000 0x200000;bootm"
+
+/*
+ * Command line configuration.
+ */
+#define CONFIG_CMD_BDI		/* bdinfo			*/
+#define CONFIG_CMD_BOOTD	/* bootd			*/
+#define CONFIG_CMD_CONSOLE	/* coninfo			*/
+#define CONFIG_CMD_ECHO		/* echo arguments		*/
+#define CONFIG_CMD_IMI		/* iminfo			*/
+#define CONFIG_CMD_ITEST	/* Integer (and string) test	*/
+
+#define CONFIG_CMD_LOADB	/* loadb			*/
+#define CONFIG_CMD_LOADS	/* loads			*/
+#define CONFIG_CMD_MEMORY	/* md mm nm mw cp cmp crc base loop mtest */
+#define CONFIG_CMD_MISC		/* Misc functions like sleep etc*/
+#define CONFIG_CMD_RUN		/* run command in env variable	*/
+#define CONFIG_CMD_SAVEENV	/* saveenv			*/
+#define CONFIG_CMD_SETGETDCR	/* DCR support on 4xx		*/
+#define CONFIG_CMD_SOURCE	/* "source" command support	*/
+#define CONFIG_CMD_XIMG		/* Load part of Multi Image	*/
+
+#define CONFIG_CMD_NAND
+#define CONFIG_CMD_MMC
+#define CONFIG_CMD_FAT
+
+/*
+ * Serial download configuration
+ */
+#define CONFIG_LOADS_ECHO	1	/* echo on for serial download */
+#define CONFIG_LOADS_BAUD_CHANGE	1	/* allow baudrate change */
+
+/*
+ * Miscellaneous configurable options
+ */
+#define	CONFIG_SYS_LONGHELP			/* undef to save memory */
+#define	CONFIG_SYS_PROMPT		"SAKC# "	/* Monitor Command Prompt */
+#define	CONFIG_SYS_CBSIZE		256	/* Console I/O Buffer Size */
+#define	CONFIG_SYS_PBSIZE		(CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
+/* Print Buffer Size */
+#define	CONFIG_SYS_MAXARGS		16	/* max number of command args*/
+
+#define CONFIG_SYS_MALLOC_LEN		128 * 1024
+#define CONFIG_SYS_BOOTPARAMS_LEN	128 * 1024
+
+#define CONFIG_SYS_SDRAM_BASE		0x80000000     /* Cached addr */
+#define CONFIG_SYS_INIT_SP_OFFSET	0x400000
+#define CONFIG_SYS_LOAD_ADDR		0x80600000     /* default load address */
+#define CONFIG_SYS_MEMTEST_START	0x80100000
+#define CONFIG_SYS_MEMTEST_END		0x80800000
+
+/*
+ * Environment
+ */
+#define CONFIG_ENV_IS_IN_NAND	1	/* use NAND for environment vars */
+
+/*
+ * NAND FLASH configuration
+ */
+/* NAND Boot config code */
+#define JZ4740_NANDBOOT_CFG	JZ4740_NANDBOOT_B8R3 
+
+#define SAKC_NAND_SIZE	1 /* if board nand flash is 1GB, set to 1
+				   * if board nand flash is 2GB, set to 2
+				   * for change the PAGE_SIZE and BLOCK_SIZE
+				   * will delete when there is no 1GB flash
+				   */
+
+#define CONFIG_SYS_NAND_PAGE_SIZE	(2048 * SAKC_NAND_SIZE)
+/* nand chip block size	*/
+#define CONFIG_SYS_NAND_BLOCK_SIZE	(256 * SAKC_NAND_SIZE << 10)	
+/* nand bad block was marked at this page in a block, start from 0 */
+#define CONFIG_SYS_NAND_BADBLOCK_PAGE	127 
+/* ECC offset position in oob area, default value is 6 if it isn't defined */
+#define CONFIG_SYS_NAND_ECC_POS	(6 * SAKC_NAND_SIZE)
+#define CONFIG_SYS_MAX_NAND_DEVICE     1
+#define NAND_MAX_CHIPS          1
+#define CONFIG_SYS_NAND_BASE           0xB8000000
+#define CONFIG_SYS_NAND_SELECT_DEVICE  1 /* nand driver supports mutipl.*/
+#define CONFIG_SYS_ONENAND_BASE	CONFIG_SYS_NAND_BASE
+
+/*
+ * IPL (Initial Program Loader, integrated inside CPU)
+ * Will load first 8k from NAND (SPL) into cache and execute it from there.
+ *
+ * SPL (Secondary Program Loader)
+ * Will load special U-Boot version (NUB) from NAND and execute it. This SPL
+ * has to fit into 8kByte. It sets up the CPU and configures the SDRAM
+ * controller and the NAND controller so that the special U-Boot image can be
+ * loaded from NAND to SDRAM.
+ *
+ * NUB (NAND U-Boot)
+ * This NAND U-Boot (NUB) is a special U-Boot version which can be started
+ * from RAM. Therefore it mustn't (re-)configure the SDRAM controller.
+ *
+ */
+#define CONFIG_SYS_NAND_U_BOOT_DST		0x80100000	/* Load NUB to this addr */
+#define CONFIG_SYS_NAND_U_BOOT_START	CONFIG_SYS_NAND_U_BOOT_DST 
+/* Start NUB from this addr*/
+
+/*
+ * Define the partitioning of the NAND chip (only RAM U-Boot is needed here)
+ */
+#define CONFIG_SYS_NAND_U_BOOT_OFFS	(256 << 10)	/* Offset to RAM U-Boot image */
+#define CONFIG_SYS_NAND_U_BOOT_SIZE	(512 << 10)	/* Size of RAM U-Boot image */
+
+#define CONFIG_ENV_SIZE		CONFIG_SYS_NAND_BLOCK_SIZE
+#define CONFIG_ENV_OFFSET	(CONFIG_SYS_NAND_BLOCK_SIZE + CONFIG_SYS_NAND_U_BOOT_SIZE + CONFIG_SYS_NAND_BLOCK_SIZE)
+/* environment starts here  */
+#define CONFIG_ENV_OFFSET_REDUND	(CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)
+
+/* in qi_lb60.h/config.mk TEXT_BAS = 0x88000000 */
+#define CONFIG_SYS_MONITOR_BASE	TEXT_BASE
+
+/*
+ * SDRAM Info.
+ */
+#define CONFIG_NR_DRAM_BANKS	1
+
+/* SDRAM paramters */
+#define SDRAM_BW16		1	/* Data bus width: 0-32bit, 1-16bit */
+#define SDRAM_BANK4		1	/* Banks each chip: 0-2bank, 1-4bank */
+#define SDRAM_ROW		13	/* Row address: 11 to 13 */
+#define SDRAM_COL		9	/* Column address: 8 to 12 */
+#define SDRAM_CASL		2	/* CAS latency: 2 or 3 */
+
+/* SDRAM Timings, unit: ns */
+#define SDRAM_TRAS		45	/* RAS# Active Time */
+#define SDRAM_RCD		20	/* RAS# to CAS# Delay */
+#define SDRAM_TPC		20	/* RAS# Precharge Time */
+#define SDRAM_TRWL		7	/* Write Latency Time */
+#define SDRAM_TREF	        15625	/* Refresh period: 8192 cycles/64ms */
+
+/*
+ * Cache Configuration
+ */
+#define CONFIG_SYS_DCACHE_SIZE	16384
+#define CONFIG_SYS_ICACHE_SIZE	16384
+#define CONFIG_SYS_CACHELINE_SIZE	32
+
+/*
+ * GPIO definition
+ */  
+#define	GPIO_SD_DETECT		(2 * 32 + 27)
+#define GPIO_SD_CD_N		GPIO_SD_DETECT	/* SD Card insert detect */
+#define GPIO_SD_VCC_EN_N	GPIO_SDPW_EN	/* SD Card Power Enable */
+
+#endif	/* __CONFIG_H */