rtl819xx/target/linux/x86/net5501/config-default, branch realtek-unstable

x86: remove support for old kernels

2012-05-18T20:10:42+00:00

git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31804 3c298f89-4303-0410-b956-a3cf2f4a3e73

x86: sync 3.2 configs

2012-05-16T10:44:52+00:00

git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31750 3c298f89-4303-0410-b956-a3cf2f4a3e73

linux: move certain disabled symbols to the generic configs

2012-05-15T10:58:52+00:00

  * CONFIG_ARCH_DMA_ADDR_T_64BIT
  * CONFIG_ARCH_HAS_ILOG2_U32
  * CONFIG_ARCH_HAS_ILOG2_U64
  * CONFIG_ARCH_PHYS_ADDR_T_64BIT
  * CONFIG_ARCH_SUPPORTS_MSI
  * CONFIG_GENERIC_CPU_DEVICES
  * CONFIG_HWMON_DEBUG_CHIP
  * CONFIG_I2C_PXA_PCI
  * CONFIG_LEDS_GPIO
  * CONFIG_MINIX_FS_NATIVE_ENDIAN
  * CONFIG_MLX4_CORE
  * CONFIG_POWER_SUPPLY
  * CONFIG_POWER_SUPPLY_DEBUG
  * CONFIG_QUOTACTL
  * CONFIG_SDIO_UART
  * CONFIG_SENSORS_K10TEMP
  * CONFIG_SENSORS_SCH56XX_COMMON
  * CONFIG_SENSORS_VIA_CPUTEMP
  * CONFIG_SERIO_AMBAKMI
  * CONFIG_SERIO_I8042
  * CONFIG_SERIO_LIBPS2
  * CONFIG_SERIO_PCIPS2
  * CONFIG_SERIO_RAW
  * CONFIG_SERIO_SERPORT
  * CONFIG_SPI_BITBANG
  * CONFIG_SPI_GPIO

git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31737 3c298f89-4303-0410-b956-a3cf2f4a3e73

config: deprecated symbol CONFIG_LEDS_GPIO_PLATFORM

2012-02-24T10:35:20+00:00

CONFIG_LEDS_GPIO_PLATFORM went away a while ago.

http://git.kernel.org/?p=linux/kernel/git/stable/linux-stable.git;a=commit;h=2bcc7ed5b83b0a59c6976476e8788675038fb11b

Also, most platforms comment out CONFIG_LEDS_GPIO but not x86 for some reason.

Signed-off-by: Philip Prindeville 

git-svn-id: svn://svn.openwrt.org/openwrt/trunk@30708 3c298f89-4303-0410-b956-a3cf2f4a3e73

[PATCH] net5501: correct net5501 h/w configuration

2012-02-02T18:41:10+00:00

Bump to version 3.2.
Simplify and correct kernel config (based on x86/config-3.2).
Designate eth0 as wan interface, and bridge eth1/eth2/eth3.
Add heartbeat LED trigger.
Use correct CS5535 GPIO driver.
Use correct USB drivers (OHCI not UHCI).
Add MSR and HW clock support.
Add GPIO mask definition.
Add correct SATA drivers.
Add LED triggers.
[Patch from Philipp Prindeville, via  http://patchwork.openwrt.org/patch/1802/]


git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29994 3c298f89-4303-0410-b956-a3cf2f4a3e73

x86: turn off CONFIG_X86_GENERIC for geos and net5501

2010-11-21T22:56:33+00:00

CONFIG_X86_GENERIC obscures CONFIG_MGEODE_LX, etc. and causes it to use wrong cache-line size.

Signed-off-by: Philip Prindeville 

git-svn-id: svn://svn.openwrt.org/openwrt/trunk@24071 3c298f89-4303-0410-b956-a3cf2f4a3e73

x86: refresh config, enable pci express support

2010-11-17T22:41:17+00:00

git-svn-id: svn://svn.openwrt.org/openwrt/trunk@24026 3c298f89-4303-0410-b956-a3cf2f4a3e73

[x86] resync config-default, enable gpio support

2010-10-30T22:35:50+00:00

git-svn-id: svn://svn.openwrt.org/openwrt/trunk@23727 3c298f89-4303-0410-b956-a3cf2f4a3e73

[x86] add net5501 support

2010-04-11T12:36:55+00:00

This patch brings up the net5501 platform.

Note that the x86/ target included support for all x86/ class
processors.  That's not technically correct.  This should be constrained
only to the "generic" subtarget.  Every x86-class target that isn't
generic should be able to select only the optimizations/capabilities
applicable to that architectural variant.

It's also assumed that all x86 processors have keyboard & mouse ports,
ISA, DMI, ACPI... the embedded ones typically don't.  Again, moving
that to the generic subtarget.

Fortunately, this was a fairly benign tweak.

The net5501 board includes the following logic:

Geode/LX processor
CS5535 super-I/O chip
PC87360 sensor chip
Via Rhine Ethernet controllers
Via Sata controllers
USB, LEDS, I2C

Signed-off-by: Philip Prindeville 

git-svn-id: svn://svn.openwrt.org/openwrt/trunk@20794 3c298f89-4303-0410-b956-a3cf2f4a3e73