rtl819xx/target/linux/brcm47xx/image, branch master

broadcom-diag: support for the WNDR3700v3

2013-04-28T21:11:17+00:00

I recently picked up a WNDR3700 to put OpenWRT on, and only after tearing into the box did I find it 
was one of the v3 boards, with poor OpenWRT support. This patch should add the board detection and
LED/button control to the broadcom-diag module, and should generate a netgear .chk image that the
bootloader and stock firmware will accept.

The changes to the broadcom-diag module are more than a few lines because the WNDR3700v3 is driving
its LEDs through an HC164 8-bit shift register.

Signed-off-by: Owen Kirby 


git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36482 3c298f89-4303-0410-b956-a3cf2f4a3e73

brcm47xx: generate images for Linksys E.... models

2013-03-27T15:51:28+00:00

Signed-off-by: Rafał Miłecki 


git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36139 3c298f89-4303-0410-b956-a3cf2f4a3e73

brcm47xx: activate image generation for some Netgear devices which are on the market and should be supported.

2013-03-27T15:35:52+00:00

git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36137 3c298f89-4303-0410-b956-a3cf2f4a3e73

brcm47xx: generate images for more WRT...N models

2013-03-27T15:34:55+00:00

Signed-off-by: Rafał Miłecki 


git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36136 3c298f89-4303-0410-b956-a3cf2f4a3e73

brcm47xx: generate images for some more devices

2013-03-20T22:01:18+00:00

These devices should be supported by trunk now.


git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36099 3c298f89-4303-0410-b956-a3cf2f4a3e73

brcm47xx: board detection WNDR3400v2

2013-02-25T20:55:46+00:00

WNDR3400v2 is based on BCM53xx . Image that is created breaks the router somehow therefore "#".

CFE and NVRAM contain different vars - example:
CFE line original: Device eth0:  hwaddr 74-44-01-37-C6-69, ipaddr 192.168.1.1, mask 255.255.255.0
CFE after openwrt: Device eth0:  hwaddr 00-FF-FF-FF-FF-FF, ipaddr 192.168.1.1, mask 255.255.255.0

Logs were posted earlier on this mailing list: https://lists.openwrt.org/pipermail/openwrt-devel/2012-July/016174.html
Different logs with factory firmware are in the wiki: http://wiki.openwrt.org/toh/netgear/wndr3400#wndr3400v2
(and on wikidevi for example)

Signed off by: Dirk Neukirchen  


git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35790 3c298f89-4303-0410-b956-a3cf2f4a3e73

brcm47xx: create image for Netgear WNDR3400 V1

2013-01-26T20:34:38+00:00

git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35323 3c298f89-4303-0410-b956-a3cf2f4a3e73

brcm47xx: Additional BCM4716 support

2012-12-13T18:57:38+00:00

Additional BCM4716 support.  Still needs working ethernet driver.

Signed-off-by: Nathan Hintz 


git-svn-id: svn://svn.openwrt.org/openwrt/trunk@34672 3c298f89-4303-0410-b956-a3cf2f4a3e73

[brcm47xx]: generate images for the D-Link DWL-3150 as well

2012-10-27T09:42:58+00:00

git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33961 3c298f89-4303-0410-b956-a3cf2f4a3e73

[brcm47xx] generate image for Linksys e3200

2012-08-05T13:14:00+00:00

git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33003 3c298f89-4303-0410-b956-a3cf2f4a3e73