rtl819xx/target/linux/brcm47xx/base-files, branch master

brcm47xx: use old partition names again for kernel 3.8

2013-04-06T22:22:26+00:00

This fixes sysupgrade. The partition names are used all over the Internet in various howtos.

Thank you russell for spotting this problem.


git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36235 3c298f89-4303-0410-b956-a3cf2f4a3e73

brcm47xx: netconfig: add bacis support for swconfig

2013-03-09T19:24:43+00:00

Parse the cpu port from swconfig and explicitly mark the cpu port as tagged.


git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35911 3c298f89-4303-0410-b956-a3cf2f4a3e73

brcm47xx: do not use vlan0 any more.

2013-02-20T15:31:43+00:00

The Broadcom switch driver says that vlan0 should not be used with any switch other than bcm5325.

This makes OpenWrt always use vlan1 and vlan2 instead.



git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35704 3c298f89-4303-0410-b956-a3cf2f4a3e73

brcm47xx: add initial support for kernel 3.8

2013-02-16T20:28:24+00:00

This contains the following new bigger changes:
 * new partition parser which still could lake some features or have bugs
 * new nand flash driver
 * using physmap-flash flash driver for parallel flash
 * some changes to the serial flash driver

With these changes OpenWrt starts using more of the mainline flash drivers.


git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35632 3c298f89-4303-0410-b956-a3cf2f4a3e73

brcm47xx: improve cpuport detection for filesafe

2013-02-16T16:24:15+00:00

Do not try to load bcm57xx.ko any more this is not needed for kernel 2.6 and 3.X
Ask the switch driver where the CPU port is.



git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35624 3c298f89-4303-0410-b956-a3cf2f4a3e73

brcm47xx: fix network config on simpleshare

2013-02-16T15:24:48+00:00

The included patch will generate a correct network configuration on the simpletech simpleshare.

Thank you for the patch Will Holmes (RealOpty)

This closes #12361.


git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35623 3c298f89-4303-0410-b956-a3cf2f4a3e73

brcm47xx: try to automatically detect if the wan port is at port 4 and not at port 0.

2013-02-16T12:37:24+00:00

This should fix #13000.


git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35617 3c298f89-4303-0410-b956-a3cf2f4a3e73

brcm47xx: if the cpuport of the switch is port 8 assume vlan0ports: "1 2 3 4 8" and vlan0ports: "0 8"

2013-02-14T12:38:16+00:00

git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35597 3c298f89-4303-0410-b956-a3cf2f4a3e73

brcm47xx: configure vlan correctly on some recent devices.

2013-02-13T16:05:52+00:00

git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35587 3c298f89-4303-0410-b956-a3cf2f4a3e73

Add Failsafe support for Linksys E3000V1 / WRT610NV2

2013-02-04T22:40:57+00:00

Adds specification of the correct cpu_port for Linksys E3000V1 and WRT610NV2
in /lib/preinit/05_init_interfaces_brcm.  The list of devices will need to
be expanded.  Is there a way to determine the correct cpu_port to use in a
generic sense; for instance, if "/proc/switch/eth0/port/8" exists, or if
"/sys/class/net/eth0/device/driver/module/drivers/bcma:bgmac" exists?  Could
a similar method be used in "/etc/init.d/netconfig"?

Signed-off-by: Nathan Hintz 


git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35491 3c298f89-4303-0410-b956-a3cf2f4a3e73