rtl819xx/target/linux/brcm47xx/base-files/lib, branch master

brcm47xx: do not use vlan0 any more.

2013-02-20T15:31:43+00:00

The Broadcom switch driver says that vlan0 should not be used with any switch other than bcm5325.

This makes OpenWrt always use vlan1 and vlan2 instead.



git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35704 3c298f89-4303-0410-b956-a3cf2f4a3e73

brcm47xx: improve cpuport detection for filesafe

2013-02-16T16:24:15+00:00

Do not try to load bcm57xx.ko any more this is not needed for kernel 2.6 and 3.X
Ask the switch driver where the CPU port is.



git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35624 3c298f89-4303-0410-b956-a3cf2f4a3e73

Add Failsafe support for Linksys E3000V1 / WRT610NV2

2013-02-04T22:40:57+00:00

Adds specification of the correct cpu_port for Linksys E3000V1 and WRT610NV2
in /lib/preinit/05_init_interfaces_brcm.  The list of devices will need to
be expanded.  Is there a way to determine the correct cpu_port to use in a
generic sense; for instance, if "/proc/switch/eth0/port/8" exists, or if
"/sys/class/net/eth0/device/driver/module/drivers/bcma:bgmac" exists?  Could
a similar method be used in "/etc/init.d/netconfig"?

Signed-off-by: Nathan Hintz 


git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35491 3c298f89-4303-0410-b956-a3cf2f4a3e73

brcm47xx: load pps_core and ptp before tg3 to make the interface available for failsafe.

2013-01-27T21:48:28+00:00

git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35341 3c298f89-4303-0410-b956-a3cf2f4a3e73

brcm47xx: add bgmac driver

2013-01-03T02:05:22+00:00

This Ethernet driver is in early development stage and still has some problems.
This was working on my bcm4716 based device.

Thanks to Rafał Miłecki  for writing this driver.


git-svn-id: svn://svn.openwrt.org/openwrt/trunk@34995 3c298f89-4303-0410-b956-a3cf2f4a3e73

brcm47xx: build b44 as a module

2013-01-03T02:00:25+00:00

git-svn-id: svn://svn.openwrt.org/openwrt/trunk@34994 3c298f89-4303-0410-b956-a3cf2f4a3e73

brcm47xx: run ifup before starting the switch

2013-01-03T01:59:43+00:00

In addition check_module is not needed, nobody checks the return value.


git-svn-id: svn://svn.openwrt.org/openwrt/trunk@34993 3c298f89-4303-0410-b956-a3cf2f4a3e73

Do not use deprecated path to functions.sh (/etc/functions.sh -> /lib/functions.sh)

2012-12-19T16:07:50+00:00

git-svn-id: svn://svn.openwrt.org/openwrt/trunk@34793 3c298f89-4303-0410-b956-a3cf2f4a3e73

Do not overload mount-call - trying to reduce confusion

2012-12-19T16:07:46+00:00

The behaviour of calling 'mount' differed depending on whether it called
the busybox-mount, the mount of util-linux, the mount defined in
/lib/functions.sh and /lib/functions/boot.sh

/etc/preinit even included /lib/functions.sh and /lib/functions/boot.sh,
both re-defining 'mount'.

git-svn-id: svn://svn.openwrt.org/openwrt/trunk@34792 3c298f89-4303-0410-b956-a3cf2f4a3e73

brcm47xx: improve suppressing printing if a module was found in preinit function.

2012-12-14T22:45:12+00:00

Thank you Bastian Bittorf


git-svn-id: svn://svn.openwrt.org/openwrt/trunk@34680 3c298f89-4303-0410-b956-a3cf2f4a3e73