rtl819xx/package/switch/Makefile, branch toolchain-unstable

bcm63xx: switch to b53 and swconfig

2013-01-23T10:12:40+00:00

Switch to using the B53 switch driver where appropriate.

Use a non-tagged default config where it isn't confirmed to be
working.

Remove the switch configuration in preinit as the switch will now
be configured by the driver  to use port isolation to prevent leakage
between lan and wan.

While at it, also provide a switch config for Neufbox 6.

Signed-off-by: Jonas Gorski 

git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35307 3c298f89-4303-0410-b956-a3cf2f4a3e73

switch: ROBO Switch Gigabit MII Support

2013-01-03T01:58:01+00:00

I wrote this patch some time ago because I had a need for one of the
Gigabit ports (Linksys E3000) to be forced to 100FD.  This is based
on the robocfg sources included w/ the RT-N16 sources from ASUS.
Since work is progressing on a BGMAC driver that could be included in
OpenWRT, this may be useful to someone else.

In testing, forcing the speed to 10/100 or 1000 worked fine; however,
when trying to force full-duplex mode, the result was always
half-duplex.  I was not able to isolate the source of the problem
(this patch, driver or H/W limitation).  The only way I could get it
to work was to set the port to Auto, but then only advertise 100FD
(not included in this patch).

I have a modified version of the robocfg package as well, I'd have to
clean it up a little first (remove the full-duplex hack) before
submitting it if there is interest.

Signed-off-by: Nathan Hintz 


git-svn-id: svn://svn.openwrt.org/openwrt/trunk@34992 3c298f89-4303-0410-b956-a3cf2f4a3e73

[package] switch: the hardware must be up while configuring

2012-03-13T21:15:41+00:00

Since the removal of the interface coldplug hack the timing changed in such a way that eth0 is not up during switch setup,
leading to an inaccesible device. Bring up the switch interface before configuring it to mitigate the problem.


git-svn-id: svn://svn.openwrt.org/openwrt/trunk@30937 3c298f89-4303-0410-b956-a3cf2f4a3e73

switch: update for brcm47xx target

2011-08-04T20:07:58+00:00

* remove suport for 2.4 kernel
* add support for bcma bus



git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27904 3c298f89-4303-0410-b956-a3cf2f4a3e73

[package] switch: fix switch-robo device reference counting

2011-02-20T17:24:15+00:00

Fix incorrect device reference counting by switch-robo.

Signed-off-by: George Kashperko 

git-svn-id: svn://svn.openwrt.org/openwrt/trunk@25619 3c298f89-4303-0410-b956-a3cf2f4a3e73

massive: replace occurences of .$(LINUX_KMOD_SUFFIX) with .ko after r21950

2010-07-12T14:06:13+00:00

git-svn-id: svn://svn.openwrt.org/openwrt/trunk@22145 3c298f89-4303-0410-b956-a3cf2f4a3e73

remove linux 2.4 support from several packages

2010-06-26T20:43:41+00:00

git-svn-id: svn://svn.openwrt.org/openwrt/trunk@21954 3c298f89-4303-0410-b956-a3cf2f4a3e73

[package] switch: explicitely clear port mappings in unsused vlans (#7082)

2010-04-05T13:51:26+00:00

git-svn-id: svn://svn.openwrt.org/openwrt/trunk@20717 3c298f89-4303-0410-b956-a3cf2f4a3e73

[package] fix strange LED behavior with Netgear WGT634U (#3552)

2009-04-20T10:27:46+00:00

git-svn-id: svn://svn.openwrt.org/openwrt/trunk@15290 3c298f89-4303-0410-b956-a3cf2f4a3e73

get rid of $Id$ - it has never helped us and it has broken too many patches ;)

2009-04-17T14:09:46+00:00

git-svn-id: svn://svn.openwrt.org/openwrt/trunk@15242 3c298f89-4303-0410-b956-a3cf2f4a3e73